Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹19.1 LAccepted-AOC NEAR INDUSTRIAL ESTATE THANDA PADDAR UDHAMPUR J K 182101 | UDHAMPUR | JAMMU AND KASHMIR | 182101 | ₹19.1 L | L1 | Accepted-AOC Accepted being lowest bidder |
| 2 | L2₹19.6 LRejected-AOC NEW JAIL ROAD UDHAMPUR J K 182101 | UDHAMPUR | JAMMU AND KASHMIR | 182101 | ₹19.6 L | L2 | Rejected-AOC Rejected not being lowest bidder |
| 3 | L3₹22.7 LRejected-AOC | ₹22.7 L | L3 | Rejected-AOC Rejected not being lowest bidder |
| 4 | L4₹23.8 LRejected-AOC DAYA BAGH SATTANI DHAR ROAD UDHAMPUR DISTT UDHAMPUR J K 182101 | UDHAMPUR | JAMMU AND KASHMIR | 182101 | ₹23.8 L | L4 | Rejected-AOC Rejected not being lowest bidder |
| Sl No | Description | Qty | Unit | SINGH CONST CO L2 | K S BUILDERS L1 | M/SHansrajbuilder L4 | PRATAP TRADING CO L3 |
|---|---|---|---|---|---|---|---|
| 1.00 | Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable 3 Ph induction motor 75KW/100 HP rating alongwith Vertical terbine pump set , four stage (Mode-lBHR 28-18 , Make - kirloskar) installed at Jackwell at GE(Army) Dhar Road from the base plate,column pipe and shifting the Motor to Civil workshop for repair/rewinding. Dismantling the motor, rotor ,shaft, slip rings,carbon brush assembly etc carefully. cutting and removing the old heated up/burnt winding of the stater /rotor, cleaning the slots and replacement of brunt spare parts and reassembling the motor including transportation back the same after rewinding and reassembling in same position at the same location,complete all as specified and directed by Engr -in- Charge.
Note:- (a) cost of rewinding will be measured and paid separately.
(b) Motor shall be dismantled at workshop and its winding shall be cut in presence of authorised MES rep. (c) Labour for fixing of any type Spare parts will be included. (d) Major Spare parts such as bearing & shaft if found defective will be measured and paid separately. (e) The rates quoted shall be deemed to include the cost of loading/unloading, transportation(To & Fro), greasing & replacement of worn out nuts, bolts,pins, rubber gasket, washers, insulating materials for motor/stator winding etc i.e varnish, cotton tape insulating paper and soldering of any type/size and shape in order to make it functional and testing at its original location/position complete. | 1 | Each job | 15,000 ₹15,000 | 12,000 ₹12,000 | 7,000 ₹7,000 | 15,000 ₹15,000 |
| 2.00 | Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable Vertical terbine pump set , four stage (BHR 28-18) along with 3 Ph induction motor 75KW/100 HP installed at Jackwell at GE(Army) Dhar Road from the base plate,column pipe and shifting the same to Civil workshop for repair of pump set. Dismantling the pump parts such as key, coupling,bush, gland, ring, shaft sleeve,impeller, bearing, nut,bolt,washers,rubber gaskets/oil seals etc any type and size from the pump carefully. Replacement of UNSV spare parts and reassembling & refitting the Pump set complete in same position after testing including transportation complete all as specified and directed by Engr-in-Charge.
Note:- (a) Pump shall be dismantled at workshop in presence of authorised MES rep. (b) The rate includes the labour for fixing of any type Spare parts will be included. (c ) The rates quoted shall be deemed to include the cost of loading/unloading Motor , transportation(To & Fro), greasing, relacement of worn out nuts, bolts,pins, rubber gaskets/oil seals and washers etc of any size and shape duly. (d) Major Spare parts will be measured and paid separately. (e) the rate includes refixing the pumps in its original positioin, testing complete . | 1 | Each job | 10,000 ₹10,000 | 12,000 ₹12,000 | 7,000 ₹7,000 | 14,000 ₹14,000 |
| 3.00 | All as per Item no 1 above but for repair of 3 Ph induction Motor 55kw/75hp alongwith Centrifugal pump set , Model - DSM 125/40 Make Kirloskar installed at Fresh water sump at Dhar Road complete all as specified and directed by Engr -in- Charge.
Note:-(a) to (e) all as per item 1 above | 1 | Each job | 6,000 ₹6,000 | 8,000 ₹8,000 | 9,000 ₹9,000 | 7,000 ₹7,000 |
| 4.00 | All as per Item no 2 above but for repair of Centrifugal Pump 55kw/75hp alongwith 3 Ph induction Motor , Model - DSM 125/40 Make Kirloskar installed at Fresh water sump at Dhar Road complete all as specified and directed by Engr -in- Charge.
Note:-(a) to (e) all as per item 2 above | 3 | Each job | 20,000 ₹60,000 | 21,000 ₹63,000 | 21,000 ₹63,000 | 18,000 ₹54,000 |
| 5.00 | All as per Item no 1 above but for repair of 3 Ph induction Motor 1.5kw/5kw alongwith Centrifugal pump set , Model - DSM 125/40 Make Kirloskar installed at Fresh water sump at Dhar Road complete all as specified and directed by Engr -in- Charge.
Note:-(a) to (e) all as per item 1 above | 2 | Each job | 1,000 ₹2,000 | 18,000 ₹36,000 | 4,000 ₹8,000 | 3,400 ₹6,800 |
| 6.00 | All as per Item no 1 above but for repair of unserviceable 3 Ph induction motor of 15 KW/20 HP rating alongwith Pump Set make Kirloskar, having RPM 2940,head 300 Mtrs, discharge 7.2 Cubic Meter per Hour installed at Samana Banj Station under GE (A) Dhar Road complete all as specified and directed by Engr -in- Charge.
Note:- (a) to (e) all as per item 1 above | 2 | Each job | 5,000 ₹10,000 | 6,000 ₹12,000 | 6,000 ₹12,000 | 5,000 ₹10,000 |
| 7.00 | All as per Item no 2 above but for repair of Centrifugal Pump of 16 KW/20 H P alongwith 3 Ph induction Motor make Kirloskar , having RPM 2940, head 300 Mtrs, discharge 7.2 Cubic Meter per Hour installed at Samana Banj Station under GE (A) Dhar Road complete all as specified and directed by Engr -in- Charge.
Note:-(a) to (e) all as per item 2 above | 2 | Each job | 5,000 ₹10,000 | 6,000 ₹12,000 | 6,000 ₹12,000 | 5,000 ₹10,000 |
| 8.00 | Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable Diesel engine driven Kirloskar make having prime mover(Motor) rating 32 HP,24 KW, Speed installed at Samana Banj location under GE (A) Dhar Road from the base plate and shifting the same to civil workshop for repair of pump set. Dismantling the pump parts such as key, coupling,bush, gland, ring, shaft sleeve,impeller, bearing, nut,bolt,washers,rubber gasket etc any type and size from the pump carefully. Replacement of UNSV spare parts and reassembling the Pump set complete as before including transportation and fixing it back after repairing and testing complete all as specified and directed by Engr -in- Charge.
Note:- (a) Pump shall be dismantled at workshop in presence of authorised MES rep. (b) The rate includes the labour for fixing of any type Spare parts will be included. (c) The rates quoted shall be deemed to be included the cost of loading/unloading, transportation from Samanabanj station under GE (A) Dhar Raod, grease, nuts, bolts,pins, rubber gaskets, oil seals and washers etc of any size and shape duly. (d) Major Spare parts will be measured and paid separately. (e) Quoted rate includes refixing the pump with Engine in its original positioin including testing complete all as directed by EIC. | 1 | Each job | 10,000 ₹10,000 | 6,000 ₹6,000 | 13,000 ₹13,000 | 10,000 ₹10,000 |
| 9.00 | Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable Diesel engine driven Kirloskar make having prime mover(Motor) rating 15 KW, Speed 2930 rpm, pump head 280 Mtrs, discharge 7.20 cubic meter/hour, pump inupt 10.67 KW installed at Samana Banj location from the base plate and shifting the same to civil workshop for repair of Engine set. Dismantling the IC Engine parts such as cylinder head ,Fuel pipes, FIP assembly, air/ fuel/ lub oil filters, greasing whereas required including replacement of worn out nut,bolt,washers,rubber gaskets, oil seals etc any type and size from the Engine set carefully. Replacement of UNSV spare parts and reassembling the Engine complete in same position including transportation and reinstalling after repairing and testing complete all as specified and directed by Engr -in- Charge.
Note:- (a) Engine shall be dismantled at workshop in presence of authorised MES rep. (b) The rate includes the labour for fixing of any type Spare parts. (c) The rates quoted shall be deemed to include the cost of loading/unloading, transportation(To & fro) from Samanabanj station under GE (A) Dhar Raod, grease, nuts, bolts,pins, rubber gaskets, oil seals and washers etc of any size and shape. (d) Major Spare parts will be measured and paid separately. (e) Quoted rate includes refixing the Engine with pump in its original positioin including testing complete all as directed by EIC. | 1 | Each job | 4,000 ₹4,000 | 4,800 ₹4,800 | 4,000 ₹4,000 | 3,000 ₹3,000 |
| 10.00 | M&L for cleaning of over head tank /under ground sump by scrapping / removing all algae/moss,funges, scales, dust, sludge etc from inner walls & floor of the over head tank and depositing the same to a distance exc. 50 mtrs and n.exc. 100 mtrs including washing the walls & floor of the over head tank with water and disinfection chemical such as bleaching powder etc and writing date of cleaning, Capacity of tank, CA No with synthetic enamel black/white paint complete for 150000 gallons capacity complete all as specified and directed. (Near Filter plant) | 1 | Each job | 10,000 ₹10,000 | 8,600 ₹8,600 | 9,000 ₹9,000 | 7,500 ₹7,500 |
Updated dates
Tender Value
₹25 L
EMD Value
₹50,000
Closing Date
7 Feb 2026, 6:00 pmClosed
GE Army Dhar Road
GE Army Dhar Road
REPAIR REPLACEMENT OF VT PUMPS CENTRIFUGAL PUMPS MOTORS ETC AND CONNECTED WORKS AT SAMNABANJ RC PEAK BATTAL JINDRAH AND DHAR ROAD UNDER GE ARMY DHAR ROAD
2025_MES_738636_2
8071/NIT-73/2025-26
Open Tender
Civil Works
180 days
GE Army Dhar Road
Please refer Tender documents.
6 documents required · 6 mandatory
₹500
Yes
GE Army Dhar Road
₹50,000
Yes
13 Mar 2026
17 Jan 2026
9 Feb 2026
17 Jan 2026
7 Feb 2026
24 Jan 2026
Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable 3 Ph induction motor 75KW/100 HP rating alongwith Vertical terbine pump set , four stage (Mode-lBHR 28-18 , Make - kirloskar) installed at Jackwell at GE(Army) Dhar Road from the base plate,column pipe and shifting the Motor to Civil workshop for repair/rewinding. Dismantling the motor, rotor ,shaft, slip rings,carbon brush assembly etc carefully. cutting and removing the old heated up/burnt winding of the stater /rotor, cleaning the slots and replacement of brunt spare parts and reassembling the motor including transportation back the same after rewinding and reassembling in same position at the same location,complete all as specified and directed by Engr -in- Charge. Note:- (a) cost of rewinding will be measured and paid separately. (b) Motor shall be dismantled at workshop and its winding shall be cut in presence of authorised MES rep. (c) Labour for fixing of any type Spare parts will be included. (d) Major Spare parts such as bearing & shaft if found defective will be measured and paid separately. (e) The rates quoted shall be deemed to include the cost of loading/unloading, transportation(To & Fro), greasing & replacement of worn out nuts, bolts,pins, rubber gasket, washers, insulating materials for motor/stator winding etc i.e varnish, cotton tape insulating paper and soldering of any type/size and shape in order to make it functional and testing at its original location/position complete.
Taking out with proper shut down by disconnecting all the electrical connections, dismantling the unserviceable Vertical terbine pump set , four stage (BHR 28-18) along with 3 Ph induction motor 75KW/100 HP installed at Jackwell at GE(Army) Dhar Road from the base plate,column pipe and shifting the same to Civil workshop for repair of pump set. Dismantling the pump parts such as key, coupling,bush, gland, ring, shaft sleeve,impeller, bearing, nut,bolt,washers,rubber gaskets/oil seals etc any type and size from the pump carefully. Replacement of UNSV spare parts and reassembling & refitting the Pump set complete in same position after testing including transportation complete all as specified and directed by Engr-in-Charge. Note:- (a) Pump shall be dismantled at workshop in presence of authorised MES rep. (b) The rate includes the labour for fixing of any type Spare parts will be included. (c ) The rates quoted shall be deemed to include the cost of loading/unloading Motor , transportation(To & Fro), greasing, relacement of worn out nuts, bolts,pins, rubber gaskets/oil seals and washers etc of any size and shape duly. (d) Major Spare parts will be measured and paid separately. (e) the rate includes refixing the pumps in its original positioin, testing complete .
All as per Item no 1 above but for repair of 3 Ph induction Motor 55kw/75hp alongwith Centrifugal pump set , Model - DSM 125/40 Make Kirloskar installed at Fresh water sump at Dhar Road complete all as specified and directed by Engr -in- Charge. Note:-(a) to (e) all as per item 1 above
All as per Item no 2 above but for repair of Centrifugal Pump 55kw/75hp alongwith 3 Ph induction Motor , Model - DSM 125/40 Make Kirloskar installed at Fresh water sump at Dhar Road complete all as specified and directed by Engr -in- Charge. Note:-(a) to (e) all as per item 2 above
All as per Item no 1 above but for repair of 3 Ph induction Motor 1.5kw/5kw alongwith Centrifugal pump set , Model - DSM 125/40 Make Kirloskar installed at Fresh water sump at Dhar Road complete all as specified and directed by Engr -in- Charge. Note:-(a) to (e) all as per item 1 above
All as per Item no 1 above but for repair of unserviceable 3 Ph induction motor of 15 KW/20 HP rating alongwith Pump Set make Kirloskar, having RPM 2940,head 300 Mtrs, discharge 7.2 Cubic Meter per Hour installed at Samana Banj Station under GE (A) Dhar Road complete all as specified and directed by Engr -in- Charge. Note:- (a) to (e) all as per item 1 above
All as per Item no 2 above but for repair of Centrifugal Pump of 16 KW/20 H P alongwith 3 Ph induction Motor make Kirloskar , having RPM 2940, head 300 Mtrs, discharge 7.2 Cubic Meter per Hour installed at Samana Banj Station under GE (A) Dhar Road complete all as specified and directed by Engr -in- Charge. Note:-(a) to (e) all as per item 2 above
M&L for cleaning of over head tank /under ground sump by scrapping / removing all algae/moss,funges, scales, dust, sludge etc from inner walls & floor of the over head tank and depositing the same to a distance exc. 50 mtrs and n.exc. 100 mtrs including washing the walls & floor of the over head tank with water and disinfection chemical such as bleaching powder etc and writing date of cleaning, Capacity of tank, CA No with synthetic enamel black/white paint complete for 150000 gallons capacity complete all as specified and directed. (Near Filter plant)
All as per item No 08.00 above but of capacity 75000 Gallon (MRS &Bde)
All as per item No 08.00 above but of capacity 50000 Gallon (Bde and MRS)
All as per item No 08.00 above but of capacity 25000 Gallon (Kamlesh vihar)
M&L for dismantalling the body of monoblock pump/centrifugal pump taking out impeller, bush, bearing,shaft, stuffing box & reassembling the same after replacing the defective parts & carrying out the necessary repair, cleaning the slot, remetalling, turning, polishing the pump shaft, replacement of worn out steel studs,nuts , bolts & washers including repair / replacement of ball bearing, impeller, stuffing box, greasing, varnishing, etc. and testing & commissioning in same position at desired location complete all as specified and as directed for the following for 10 HP to 15HP pump sets:
All as per item 12 above but 5 to 7.5 HP
All as per item 12 above but for 1 to 5HP sludge pump/monoblock pump/induction pump for repair of complete pump and motor complete all as specified and as directed.
Taking down unserv motor, cutting of burnt windings and rewinding the motor rotor with super enamelled copper winding wire/strip as per existing size and truns etc including all the insulating materials i.e varnish, cotton tape insulating paper and soldering,greasing including replacement of worn out nuts, bolts,pins, rubber gasket,washers etc of any size for the motor of capacity 10 to 15 HP complete all as specified and directed by Engr-in-Charge. Note:- (a) Winding shall be cut in presence of MES Rep and reassembling shall be done after inspection by MES Rep. (b) Rewinding wire of motor will be measured and paid separately under relevent item. (c) The motor shall be squerrel cage induction/slipring induction motor.
All as per item 14 above but of capacity 5 to 7.5 HP
Taking down air comperssor set with motor , cutting of burnt windings and rewinding the motor rotor with super enamelled copper winding wire/strip as per existing size and truns etc including all the insulating materials i.e varnish, cotton tape insulating paper and soldering, greasing including replacement of worn out nuts, bolts,pins, rubber gaskets/oil seals,washers etc of any size for motor capacity 30 HP complete all as specified and directed by Engr-in-Charge. Note:- (a) Winding shall be cut in presence of rep of EIC and reassembling shall be done after inspection by Rep of EIC. (b) Rewinding wire of motor will be measured and paid separately under relevent item. (c) The motor shall be squirrel cage induction/slipring induction motor.
Taking out unserviceable motor shifting to workshop and dismantalling, cutting of burnt windings and rewinding with supper enameled copper winding wire as per existing size and truns etc including all the insulating materials ie. varnish, cotton,tape, insulating paper and soldering, greasing including replacement of worn out nuts, bolts,pins, rubber gaskets/oil seals,washers etc of capacity below 5 HP, 3 phase 415 volts, incl. reassembling, reinstalling at original location or including testing complete all as specified and directed. Note:- (a) Winding cut shall be made in presence of Rep of EIC and reassembling shall be done after inspection by the Rep of EIC. (b) Rewinding wire of motor will be measured and paid separately under relevent item. (c) The motor shall be squerrel cage induction/slipring induction motor.
Rewinding the motor stater with super enamelled copper winding wire of existing size and gauge and truns etc including all the insulating materials i.e varnish with suppr high quality of cotton tape, insulating paper and other misc items of motor any capacity (vertical terbine/ centrifugal/induction) all as specified and directed by Engr-in-Charge. Note:- (a) Winding cut shall be made in presence of Rep of EIC and reassembling shall be done after inspection by the Rep of EIC.(b) Rewinding wire of motor will be measured and paid separately under relevent item.. (c) The motor shall be any type induction motor.
Supply & Fixing in replacement of 100 HP Motor bearing DE/NDE 6318-C3 or as per existing make and type complete all as specified and directed by Engr-in-Charge.
Supply & Fixing in replacement of 75 HP Motor bearing DE6314 C3 or as per existing make and type complete all as specified and directed by Engr-in-Charge.
Supply & Fixing in replacement of 75 HP Motor bearing NED 6311 C3 or as per existing make and type complete all as specified and directed by Engr-in-Charge.
Supply & Fixing in replacement of compressor Motor bearing DE/NED 6311 2Z or as per existing make and type complete all as specified and directed by Engr-in-Charge.
Supply & Fixing in replacement of Alum/bleaching Motor bearing DE/NED 6203 2Z or as per existing make and type complete all as specified and directed by Engr-in-Charge.
M&L for taking out old unserviceable existing chlorination dozing spare parts from dozing plant and repair/replacement of the unserviceable spare parts as per existing type and size like NRV, suction/delivery pipes of existing length and type/size with fixing arrangement, motor required, filter for making dozing system functional and testing and commissioing including disposing off all unserviceable taken out parts / components complete all as specified and as directed
Supply of Cooling fan blade for Induction motor of capacity 50 to 100 HP same as per the present type and size all as directed by EIC.
Disconnecting the Blower of 1200 RPM, 8.5 CFM, 30 HP and type and make carefully dismantling it with commected motor complete for servicing by cleaning the bearing/bush by cleaining solution and replacing the unserviceable items like bearing, Nut Bolt& washer,Greasing of bearing etc., assembling Blower and refixing in the original place connection and testing complete all well as specified and as directed by Engr-in-chagre.
Removing the valve with the help of crane/triport, repairing and refixing NRV 300/600 mm by replacing its old disc, rubber/leather with new sheet as per present shape, size and type, gaskit, body bonnet nut ,Stud bolt, washer,breazing,welding,lathe work etc required to repair valve complete.
Scrapping old painted/ rusted surfaces of Clariflocculator plant with emery paper, scrapping tools etc & preparing surfaces for painting with & including painting of connected Motors,MS Structure, blades etc with & including two coats of synthetic enamel paint as per existing colour code including removing/cleaning all the greasy and oil substances from the area to be painted complete all as specified and as directed by Engr - in - Charge.
Supply and fix as in repair Non Return Valve of 100 MM, PN 1 NRV along with nut, bolt, washer and rubber gas kit , including taking down of old UNSV one complete all as spd and directed by EIC.
Supply and fix as in repair Non Return Valve of 150 MM, PN 1 NRV along with nut, bolt, washer and rubber gas kit , including taking down of old UNSV one complete all as spd and directed by EIC.
Supply and fix as in repair Non Return Valve of 200 MM, PN 1 NRV along with nut, bolt, washer and rubber gas kit , including taking down of old UNSV one complete all as spd and directed by EIC.
Supply and fix as in repair Non Return Valve of 300 MM, PN 1 NRV along with nut, bolt, washer and rubber gas kit , including taking down of old UNSV one complete all as spd and directed by EIC.
Removing the valve with the help of crane/triport, repairing and refixing Sluice Valve 300/600 mm by replacing its old spindle,disc, rubber/leather with new sheet as per present shape, size and type, gaskit, body bonnet nut ,Stud bolt, washer,breazing,welding,lathe work etc required to repair valve complete.
Taking out sludge/foreign material//silt/vegetation/mud from filter bed tank at tawi filter plant (into two parts) including taking down old muddy unserviceable media filter and provide new filter media ie gravels,sand media etc as required and dewatering the residual water and cleanings the walls with the help of blade/scrapper/wire brush, preparation of old surface and applying one coat of lime wash including removing the sludge/silt/foreign material complete and depositing where directed out side the defence area complete all as specified and directed by Engr-in-Charge
Taking out sludge/foreign material/silt/vegetation/mud from the square clear water UG sumps capacity 12 Lakh gallons (in two part) dewatering the residual water and cleaning the wall with help of blade/scrapper/wire brush, preparation of old surface and applying one coat of lime wash including removing the sludge/silt/foreign material complete and depositing where directed out side defence land complete all as specified and directed by Engr-in-Charge.
Taking out sludge/foreign material//silt/vegetation/mud from the clarifloculator tanks circular type capacity 1.5 Lakh gallon and cleaning the walls with wire brush/blade/ scrapper, preparation of old surface and applying one coat of lime wash including removing the sludge/silt/foreign material complete and depositing where directed out side defence land as and when required basis complete all as specified and directed by Engineer-in-Charge.
Taking out sludge/foreign material/silt/vegetation/mud from the pre-sedimentation tank of capacity 1.5 lakh gallon and cleaning the wall tile with cleaning agent including removing the sludge/silt/foreign material and depositing where directed out side defence land as and when required basis complete all as specified and directed by Engineer-in-Charge.
Taking out sludge/foreign material/silt/vegetation/mud from the back wash chamber and Jack well by cleaning the wall tiles with cleaning agent including removing silt/sludge and depositing where directed out side defence land as and when required basis complete all as specified and directed by Engineer-in-Charge. Note: The works to be carried out in parts as at least one supply of water is to be restored per day and the contractor will arrange all type of T&P such as suction pump, wire brush, castic soda, tools & plants for destroy/dispose of mud and sludge etc. Hence tenderes are required to quote their rates accordingly after site visit.
M&L as in repair of manhole covers / valve pit covers fabricated out of MS sheet, MS flat and angle iron of required sizes or shapes required at site and painting with one coat of black synthetic enamel paint over a coat of red oxide primer including taking out / dismantling rusted or unserviceable covers of UG sump/OHT/valve pits, etc. and disposing off complete all as specified
S&F in replacement of double flanged sluice valve of size 400 mm bore class PN 1 with stainless steel spindle including replacement of worn out rubber sheet nut, bolts and washers, including taking down of old and UNSV valve complete all as specified and directed
S&F in replacement of double flanged sluice valve of size 300 mm bore class PN 1 with stainless steel spindle including replacement of worn out rubber sheet nut, bolts and washers, including taking down of old and UNSV valve complete all as specified and directed
S&F in replacement of double flanged sluice valve of size 200 mm bore class PN 1 with stainless steel spindle including replacement of worn out rubber sheet nut, bolts and washers, including taking down of old and UNSV valve complete all as specified and directed
S&F in replacement of double flanged sluice valve of size 150 mm bore class PN 1 with stainless steel spindle including replacement of worn out rubber sheet nut, bolts and washers, including taking down of old and UNSV valve complete all as specified and directed
Taking out/ lifting defective submersible pump set capacity 12.5 to 15 HP motor from bore well including motor, column pipes, steel rope, submersible cable and accessories etc for its further repair all as directed by EIC.
Lowering only submersible pump set along with motor, column pipes, steel rope, submersible cable and accessories etc after repairing including testing commissioning of submersible pump set of 20000 GPH capacity 12.5 to 15 HP motor. Note: All spares required to make the motor, pumps, column pipe etc serviceable shall be measured and paid separately under relevent items as supply only including transportation to & from upto contractor workshop
Rewinding of submersible motor, 12.5 to 15 H.P. 3 Phase, 50 Hz, 415 Volt with PVC insulated / coated copper winding wire of existing gauge with other winding material such as insulating paper, sleeves, bamboo stick etc. as per standard manufacturers specification including cleaning of stator, slots replacement of defective parts and testing complete all as directed . Note :- (a) Winding cut shall be made in presence of Rep of EIC and reassembling shall be done after inspection by the rep of EIC. (b) Rewinding wire of motor will be measured and paid separately under relevent item. (c) The motor shall be squerrel cage induction/slipring induction motor. (d) Spare parts other than winding shall be included.
Supply and fixing epoxy type cable jointing kit 10/16 Sqmm 3 core complete with all the jointing material ferrule insulation tape etc for 1100 Volts flat submersible copper conductor cable.
Labour & T&P for Machining work required for repair to submersible pump set by straightning polishing of pump shaft ,Making screw and key way,including replacement of wornout spares completes re-assembling pump after repair & testing for smooth functioning complete all as specified and directed by Engineer-in-Charge. Note :- Spare parts shall be measured & paid separately.
Supply & Fixing of submersible pumps set SS impellers with key and distance bushes suitable for 12.5 to 15 HP pump
Supply & Fixing of submersible pumps set Bearing/ bush upper & lower for submersible pump for 12.5 to 15 HP
Supply & Fixing of submersible pumps set Neck ring for submersible pump set 12.5 to 15 HP
Supply & Fixing of submersible pumps set Distance sleeves for 12.5 to 15 HP.
Supply & Fixing of submersible pumps set GM motor bush upper and lower (set of two) for 12.5 to 15 HP
Supply & Fixing of submersible pumps set Coupling with key for motor pump for 12.5 to 15 HP
Supply & Fixing of submersible pumps set Sand Guard for submersible pump set for 12.5 to 15 HP
Supply & Fixing of submersible pumps set Housing upper & lower for 12.5 to 15 HP
Supply & Fixing of submersible pumps set Thurst bearing assembly for submersible pump set motor of 12.5 to 15 HP
Supply & Fixing of submersible pumps set Casing bearing for submersible pump set 12.5 to 15 HP
Supply & Fixing of submersible pumps set Bowl suitable for submersible pump set 12.5 to 15 HP
Supply & Fixing of Flat water proof submersible cable 3 core copper conductor, PVC insulated 1100 volts grade stranded 16 Sqmm 3 Core, ISI marked and connected to pump motor through water tight sealing joints complete all as specified.
M&L for replacement of rubber flange gasket 3mm thick 6or more holes for flanged joint 65 mm to 100mm bore pipe including replacement of worn out bolts & nuts completed all as specified and directed by Engineer -in- Charge.
All as per item 64 about but for flanged joint 150mm to 300mm bore pipe.
Supply and lowering in bore hole galvanized iron column pipe 100mm dia medium grade (appromimately in 3m lengths) each duly flanged at both ends by welding with specials such as slots for housing and holes for fixing nut bolts including painting with one coat of synthetic enamel paint over a coat of primer, taking out and disposing off old unseviceable pipes complete as specified and as directed
Supply & fixing in replacement of old unserv starter by Manual Star Delta starter consisiting of ampmetre,voltmetre,indicator lamp,ON/OFF push button,TP MCB etc suitable for motor pump set of capacity 15/30H.P. including making all electric connection complete all as specified by EIC.
Servicing,repairing and over hauling of mehanism of clariflocculator including replacement of chain and gear box including oiling greasing and making good as serviceable condition all as specified and directed by Engineering -in- Charge.
Repairing of clarifloculator rubber pading (wheel), bearing, chain, motor and overhauling complete and cleaning well mentained all as specified and directed Note:- rubber padding taken seperately
Supply & fixing in replacement of old unserv starter by Manual Star Delta starter consisiting of ampmetre,voltmetre,indicator lamp,ON/OFF push button,TP MCB etc suitable for motor pump set of capacity 100/75 HP. including making all electric connection complete all as specified by EIC.
Repairing /replacement t of automatic star delta starter, decarbonised of all contacts,relay , thimble etc and cleaning ,making good ,tighting of all cables , wires and other connected items oiling in moving macnism if any etc incl replacement of burnt parts on as requirement basis cmoplete all as specified and directed for 75/100 HP starter complete all as specified and directed .
All as per item 72 above but for 15HP to 50HP pump.
M&L for maintenance of Electric supply panel for Motor any type and size by replacing /repairing of necessary spares as per existing capacity / type required for healthy operation of the motor like contactors of various types /capacity ,over load relay ,single phase preventor ,voltage fluctuation protector, ammeter/voltmeter of existing size / capacity and type ,3phase indicator lamps complete all as specified and as directed.
Supply ,fixing and testing in repairs water pressure gauge ,dial type 100mm nominal dia with control valve ,socket ,union ,and adopter , range 0-100 PSI fixied with 150mm long , 15mm dia GI pipe medium dia GI pipe medium grade with suitable arangement for fixing on 150/200mm DI/CI by using clamps ,complete all as specified and as directed.
Supply and fix as in repair electronic motor protection relay type Selec MPR-341-2 or equvalent as per existing type and size and as directed by EIC.
Supply and fix as in repair of Contactor of 3 P, AC & DC control 300A, 185a having Aux contact No 02 and NC 02 cat part No IC 185AN3P**22 of HPL or equavalent as per existing type and size and as directed by EIC.
Supply and fix as in repair of Contactor of 3 P, AC & DC control 150a having Aux contact No 02 and NC 02 cat part No IC 150AN3P**22 of HPL or equavalent as per existing type and size and as directed by EIC.
Supply and fixing in repair MCCB 400 Amp, 4 Pole, 50 Hz, 36 KA magnetic and thermal adjustments type complete as to be fitted in existing size panel all as spd and directed.
Supply and fixing in repair MCCB 250 Amp, 3 Pole, 50 Hz, 25 KA magnetic and thermal adjustments type complete as to be fitted in existing size panel all as spd and directed.
Supply and fixing in repair MCCB 315 Amp, 4 Pole, 50 Hz, 36 KA magnetic and thermal adjustments type complete as to be fitted in existing size panel all as spd and directed.
Supply and fixing in repair MCCB 160 Amp, 3 Pole, 50 Hz, 25 KA magnetic and thermal adjustments type complete as to be fitted in existing size panel all as spd and directed.
Supply and fix as in repair of L&T 66 -110 A Thermal Overload Relays for MNX R4 , 500V, 50Hz, 2Z, AC 15 Max fuse 6A or equavalent as per existing type and sizse and as directed by EIC.
Supply and fix as in repair of Contactor of L&T MNX 110 3 Pole Power Contactor 110 A 2 NO + 2 NC CS94137 or equavalent as per existing type and sizse and as directed by EIC.
Supply and fix as in repair timer type ET 100 or as per existing type and size and as directed by EIC.
Supply and fix as in repair 3 Pole DC control power contactor (LC1E120) 3P(3 NO) - AC-3 - <= 440 V 120A - 24 V AC coil or equvalent as per existing type and size and as directed by EIC.
Supply and fix as in repair schneder Overload RELAY LRE 08A class 10A type or as per existing type and size and as directed by EIC.
Supply and fix as in repair Electronic Timer -series Micon Tm 175240VAC, 50 Hz, tolerance -20% to 10% ,or as per existing type and size to match the panel and as directed by EIC.
Supply & fixing in repair of panel mounted AC Amp meter, three phase square size, flush mounted case, accuracy class - 0.5 complete as per existing type and size to match the panel and as directed by EIC.
Supply & fixing in repair of panel mounted AC Volt meter , three phase in square size, flush mounted case, accuracy class - 0.5 complete as per existing type and size to match the panel and as directed by EIC.
Supply & Fixing of Bearing as in repair for three phase induction motor of make Kirloskar, 15/20 (KW/20HP) motor part No SKF Deep Groove Ball Bearings, 6309-2Z or as per existing make and type all as directed by EIC.
Supply and fixing in repair on load change over switch 250amp, Open Execution ,4 pole ,415 V ac complete all as specified and directed..
Taking down unserviceable copper pipe of any size and type carefully from VT pump set and supply & fixing new copper pipe 1/2" complete including brazing, welding, but bolts and screws of reqd size complete all as existing type and size as directed by Engr-in-Charge.
Taking down ball valve as in repair and supply & fixing new brass ball valve of 25 mm complete all as directed by Engr-in-Charge
Taking down ball valve as in repair and supply & fixing new brass ball valve of 20 mm complete all as directed by Engr-in-Charge
Taking down ball valve as in repair and supply & fixing new brass ball valve of 15 mm complete all as directed by Engr-in-Charge
Supply & Fixing of Intermediate Shaft Part No 1840101 complete to match with the Kirloskar vertical turbine pump model BHR 28 Pump model all as directed by EIC.
Supply & Fixing of Head Shaft No 1850001complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed by EIC.
Supply & Fixing of Impeller shaft No. 1860101complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Wearing Ring complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Sealing ring complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Split Gland complete to match with the Kirloskar vertical turbine pump model BHR 28Pump all as directed by EIC.
Supply & Fixing of Liquid deflector complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Bearing spider complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Bearing Spider Lower complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC
Supply & Fixing of Brg Spider lower with WR complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC
Supply & Fixing of Shaft Sleeve complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Shaft Sleeve complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Shaft Sleeve complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Shaft Sleeve complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Distance Sleeve complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Key complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Key complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC. .
Supply & Fixing of Key complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Key complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Key complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Key complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Impeller and Nut complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Shaft Sleeve Nut complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Bearing nut complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Lock nut complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Rubber bearing lower complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Rubber bearing complete to match with the Kirloskar vertical turbine pump as per existing type and size and as directed by EIC.
Supply & Fixing of Rubber bearing complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Journal Bearing complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
Supply & Fixing of SCR. Coupling complete to match with the Kirloskar vertical turbine pump model BHR 28Pump as per existing type and size and as directed by EIC.
M & L for Gland Packing for pumpmotor set as per the existing size and type complete all as directed by Engr-in-Charge
Supply & Fixing of CI Impeller I-Stg DSM 125-40 (Full dia) complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of CI Impeller II-STG DSM 125-40 (Full dia) complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of pump shaft (CS40C8) complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of wear Ring complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Shoulder Ring 63 DX10L Part No 1990101 complete to match with theKirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Interstage Ring complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Split lantern Ring complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Gland complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Liquid Defletor-48D (Na Rubber) complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Brg Cartridge-DE complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Brg Cartridge-NDE complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Bearing Cover complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Bearing Cap complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC
Supply & Fixing of shaft sleeve complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Bronze Shaft Sleeve nut complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of lock nut M45X1.5 RH complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Throat Bush complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of set of keys Part No SSOK1 complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Set of Gland Packing Part No SSOG complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply & Fixing of Set of O Rings Part No SSOR1 complete to match with the Kirloskar DSM 125/40 Pump as per existing type and size and as directed by EIC.
Supply and fixing of Set of bearing for 1.5 HP motor (for sedimentation/clariflocculator unit) of end carriage drive complete all to match with the motor all as per existing type and size and as directed by EIC.
Supply and fixing of Set of bearing for Premium reduction gear box (A-337 of end carriage drive complete all to match with the motor all as per existing type and size and as directed by EIC
Supply and fixing of Worm Shaft for A-377 Gear Box complete all to match with the motor all as per existing type and size and as directed by EIC.
Supply and fixing of Set of Oil seals for A-337 Gear Box complete all to match with the motor all as per existing type and size and as directed by EIC.
Supply and fixing of Set of cabon brush (motor cap 1.5 to 2 HP) for the central current collector complete all to match with the motor all as per existing type and size and as directed by EIC.
Supply and fixing of Central current collector complete all to match with the motor (motor cap 1.5 to 2 HP) all as per existing type and size and as directed by EIC.
Supply and fixing of CI wheel (for sedimentation and clariflocculator unit) with rubber padding, plummer block with bearing for end carriage drive complete all to match with the motor all aas per existing type and size and as directed by EIC.
Supply and fixing of Set of bearing for 1 HP motor all as per existing type and size and as directed by EIC.
Supply and fixing Set of bearing for 2 HP motor of the flocculator drive complete all to match with the motor allas per existing type and size and as directed by EIC.
Supply and fixing Set of bearing for Premium V-400 reduction gear box of the flocculator drive complete all as per existing type and size and as directed by EIC.
Supply and fixing Worm Shaft for V-400 Gear Box complete all to match with the motor all as per existing type and size and as directed by EIC.
Supply and fixing Set of Oil seals for V-400 Gear box complete all to match with the motor all as per existing type and size and as directed by EIC.
S& F as in repair joint with rubber or fibre board gasket for flanged pipes and pipe fitings of size 300 mm bore complete all as per existing type and size and as directed by EIC.
M & L for DI/CI fittings for spigot socketed/flanged pipes such as bends, tappers, tee pieces single/double branches any tpe and angle /radious and straight connecting pieces for size upto 300 mm complete allas per existing type and size and as directed by EIC.
Taking up old rusted/unserviceable CI/DI water main pipes upto to 300mm bore with spigot and socketed /flanged ends with all fittings including burning out lead joints and recovering lead etc and disposing off complete all as specified and as directed of the following sizes: Note : Excavation and earthwork shall be measured and paid for separately under respective items.
Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundations, including cutting of road/hard standing, etc. for laying pipes, etc.not exceeding 10sqm on plan and getting out in hard / dense soil complete all as specified and as directed
Returning, filling in soil/loose soil including spreading, leveling,watering & well ramming in layers not .exceeding 25 cm thick complete all as specified and directed.
Removing of surplus spoil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.
M& L for PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates for making good distrubed sufaces of roads/hard stamding etc and finishing the top surfaces even and smooth without using extra cement complete all as specified and as directed
Supply and fixing as in repair of Polypropylene Filter Nozzles for Rapid gravity filters as per sample and as directed by EIC.
Supply and fixing as in repair of Polypropylene Air Stems for rapid gravity filters as per sample and as directed by EIC.
Supply and fixing 14/25 mesh fine sand filter media as per sample and as directed by EIC.
Supply and fixing 6/14 mesh coarse sand filter media as per sample and as directed by EIC.
Supply and fixing 1/4" x 1/10" gravel filter media all as per sample and as directed by EIC.
Supply and fixing as in repair of Set of bearing for Air Blower Model SMW 713 AC complete all as per existing type and size and as directed by EIC.
Supply and fixing as in repair of Air Filter for the Air Compressor, Cap 30 HP / 22 KW, 415 Volts, 1475 RPM complete all as directed by EIC.
Supply and fixing as in repair of set of oil seals for the Air Compressor, Cap 30 HP / 22 KW, 415 Volts complete all directed by EIC.
Supply and fixing as in repair of V belts for the Air Compressor, Cap 30 HP / 22 KW, 415 Volts, 1475 RPM complete all as per existing type and size and as directed by EIC.
Supply and fixing as in repair of Set of bearing for monoblock pump set of 7.5 KW, 10 HP, 2900 RPM, Model KDS-1030 complete all as per existing type and size and as directed by EIC..
Supply and fixing as in repair of Impeller for KDS 1030 Pump set complete all as per existing type and size and as directed by EIC.
Supply and fixing as in repair of Shaft with Rotor for KDS-1030 Pump set complete all aas per existing type and size and as directed by EIC.
Supply and fixing as in repair of SS Strainer Basket for 100 mm T type hair strainier complete all as directed by EIC.
Supplying, lowering and fixing of MS casing pipe ERW, 8mm wall thickness both end flanged Column Pipe of size 200 mm bore , with flanged having minimum 08 holes duly welded with MS pipe at both end, fixing with the existing bore hole/jackwell pipe with suitable size nut ,bolt and washers complete to match with the existing alignment of VT pump complete all as per existing type and size and as directed by EIC.
S& F as in repair of fabrication of VT pump Net from MS steel sheet/Wire (as per sample given) having height of 45 CM and dia of 40 Cm, of weight not less than 25 kg the net (size of hole in net will be as per sample provided) to be fixed with VT shaft in suction line of VT pump inside the jackwell with suitable size nut, bolt and washers all as directed by EIC.
M&L as in repair for earthing as per IS:3043 with galvanized steel earth plate electrode 600 x 600 x 6.0 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanized iron Strip 32 x 6 as earthing lead protected by GI pipe medium grade 15 mm bore for protection of GI earth wire and 20 mm dia GI pipe medium grade for watering with alternate layers of charcoal /coke and salt including all accessories like nut, bolts, reducer, nipple, wire meshed/screened funnel and making brick masonry finished chamber of internal size 300 mm x 300 mm x 300 mm with concrete base, covered with PCC cover which shall be embedded in the block masonry including excavation works, refilling, connected to main switch/MCB DB for feeding the electric supply to domestic quarters compete all as specified as shown in electricall plateNo. 3 of SSR Part-I and testing of earth resistance as required. Note : Earthing lead/G.I.Earth wire upto 7.5 metre length shall be deemed to be included in quoted unit rate beyond 7.5 metre, the same shall be measured and paid separately).
material and labour for cleaning main blockage pipe of size more than 450mm installed at tawi river for feeding water to jackwell setting aside not less than 50 mtr away from jackwell complete all as specified and directed by the Engineer-in-Charge.
T&P and labour for cutting /uprooting /bushes /shrubs /grass /saplings /plant /trees etc not more than 3.0mtr high and setting aside not less than 50 mtr away from tawi filter plant premises of 100sqmtr complete all as specified and directed by the Engineer-in-Charge. Note:- The jobs shall be repeated at same location after 15days
Only Supply graphite gland dori 8mm
Only Supply graphite gland dori 10mm
Only Supply graphite gland dori 14mm
Only Supply grease.
Only Supply Engine Oil 20w40
Only Supply Stainless steel Nuts,Bolts with washers of various sizes 8mm,10 mm, 12 mm, 14 mm and 16 mm.
Supply & fix complete bowl assembly for VT Pump 100 HP
M&L for taking down 150mm bore sluice valve from pipe line ,dismantling for replacement of worn out brass / steel nut driving spindle by shaping , cutting , drilling , threading on lathe machine of square shape made out of brass /steelto drive existing spindle of 300mm bore sluice valve complete all as speicfied and directed by Engineer -in- Charge.
All as per item No. Above but for Sluice Valve of bore 200mm
All as per item No. Above but for Sluice Valve of bore 150mm
All as per item No. Above but for Sluice Valve of bore 100mm
All as per item No. Above but for Sluice Valve of bore 80mm
Supply & fix Complete bowl assembly for VT Pump 100 HP.
Deduct Schedule of Credit of Rs. (-) 78268.50 (Minus) as listed in Schedule 'A' Part-II. Contract Sum shall be arrived after deducting the credit amount Note: Tenderers will not quote against this item being a firm amount.
Please Enable Macros to View BoQ information
stage.html
html • 0.05 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.34 MB
BOQ_838735.xls
BOQ • 0.46 MB
TD73.pdf
Tender Documents • 1.67 MB
Download all tender documents and submit your bid