ADDN ALTN AND STRUCTURAL REPAIRS TO FIRE STATION AT WED PROVN OF ONE WATCH TOWER AT NSD AND DEMOLITION AND RECONSTRUCTION OF TOILET BLOCK FOR C NO 24 AT SAWMILL MANKHURD UNDER GE (NW) MANKHURD

Amount

Dismantling stone slabs and tiles of any description or thickness in floors / dados, etc laid bedded and pointed in any mortar and removing debris outside MD land complete all as specified and directed.

Demolition of cement concrete un- reinforced of any description and in any position not otherwise specifically provided for and removing debris outside MD land complete all as specified and directed.

M&L screed bed or bedding layer 20mm thick for laying floor finishes in cement mortar 1:6 to recive tiles/stone slabs complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:4 to recieve tiles complete all as specified and directed.

M&L non skid ceramic coloured tiles 7-8 mm thick area of each tile exc. 0.06sqm but n.exc 0.11 sqm in floors etc, set and jointed in cement slurry and pointed in epoxy grout to match the shade of tiles complete all as specified and directed.

M&L Coloured Glazed ceramic tiles (300 x 200 mm) x 7 mm thick, in vertical surfaces such as skiriting, dados etc complete all as specified and directed.

M&L for 50mm thick plain cement concrete type C-2,1:3:6 (20mm graded stone aggregate) as in plinth protection ,finishing surface even and smooth without using extra cement and spike rollong to surfaces or making impression of expanded metal,whilst the concrete is green complete all as specified and directed.

M&L preparation of old surfaces on ceiling (plastered or unplastered or previously white washed) and applying one coat of white wash complete all as specified and directed.

Taking down cement plaster of any description from brick or stone walls including raking out joints, hacking for key , scrubbing down with water etc and removing debris outside MD land complete all as specified and directed.

M & L for rendering 12mm thick using polymer modified ready mix cement based plaster on the wall surfaces including finishing the surface of top layer even and smooth complete all as specified and directed. Note: The thickness of plaster specified above is minimum thickness and the quoted rates shall also deemed to be include for the provosion of dubbing of the surface and nothing extra shall be payable on this account. The rate also includes the rate of scaffolding and necessary safety measurements

M & L for rendering 5 mm thick using polymer modified ready mix cement based plaster on the ceiling surfaces including finishing the surface of top layer even and smooth complete all as specified and directed. Note: The thickness of plaster specified above is minimum thickness and the quoted rates shall also deemd to be include for the provosion of dubbing of the surface and nothing extra shall be payable on this account. The rate also includes the rate of scaffolding and necessary safety measurements

M & L for preparation of new plaster surface and applying three coat of white wash to wall complete all as specified and directed.

All as per item No 12 above but on ceiling

M & L preparation of old surfaces on wall (plastered or unplastered or previously white washed) and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces on walls, preparation for distempering and applying two coat of oil bound distemper over a coat of primer including stopping of nails holes,cracks etc, patch repair with putty where required. complete all as specified and directed.

M&L for 20mm (12+8mm)thick in two coats polymer modified ready mix cement based plaster on the wall surfaces complete all as specified and directed. Note: The thickness of plaster specified above is minimum thickness and the quoted rates shall also deemd to be include for the provosion of dubbing of the surface and nothing extra shall be payable on this account. The rate also includes the rate of scaffolding and necessary safety measurements

M & L for preparation of new plastered surfaces of wall etc and applying two coats of 100% anti fungal acrylic exterior emulsion paint over one coat of primer all as per manufacturer's instructions including necessary scaffoldings upto 24 mtr height etc, complete all as specified and directed.

Taking down aluminium windows,chowkats or frames with shutters (without taking off shutters from the frame) not exceeding 1.5 sqm each.incl taking down deco grill and refixing the same after cleaning, repairing, changing of locks,rubber beading, rollers etc complete all as specified and directed.

M&L machine cut prepolished cudappa stone slab flooring 20-25mm thick as in cill, jambs, soffits of cooking platform of window laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, over and including 15 mm thick screed bed in cm 1:6 complete all as speicfied and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) of area exc 1.5 Sqm and n exc 4 sqm and disposing off complete all as specified and as directed.

All as per item No 20 above but n.exc 1.5 Sqm

S&F 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S&F 35mm thick 2nd class hard wood, factory made, plain framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged) or of veneered particle board, medium density wood particle board, size of rails and styles as per IS: 1003 (Part-I), kiln seasoned and chemically pressuer treated, supplied and fitted to chowkats complete all as specified and directed.

S&F 2nd class hardwood 35mm thick glazed and skeleton shutters open and prepared to receive glass, gauze etc (with sash bars) edges of plain, chamferred or rounded, fitted with cut and mitred beads for securing gauzes etc, sizes of members and sizes of shutters as specified in SSR part -I sec 8,cluse 8.24(a).

M& L for treating with tar or coal tar black paint on back of chowkats, area tarred exec 0.1 Sqm but not exceeding 0.5 Sqm each treated with tar or coal for black paint complete all as specified and directed.

M& L for treating small articles such as stop, covers, gully gratings, hold fasts, and of posts , back of chowkats, etc area not exec 0.1 Sqm each treated with tar or coal tar black paint complete all as specified and directed.

S&F MS hold fasts and similar small articles and cutting holes in brick walls in cement mortar for removing holdfasts, inserting new one and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

M& L for preparation surfaces of new wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 100 mm long stainless steel butt hinges fixed with stainless screw complete all as specified and directed.

S&F aluminum anodised barrel tower bolts of extruded section of size 200 mm length complete all as specified and directed.

S&F 150 mm extruded aluminum alloy handles, fabricated type anodised complete all as specified and directed.

S&F 300mm long alluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and sliding bolts of extruded sections or cast alluminium alloy and fixed complete all as specified and directed

Demolition of reinforced cement concrete in roofs, floors, beams, staircases, landings, chajjas and similar suspended work (reinforcement cut to facilitate demolition) including scaffolding and necessary safety arrangements and removing debris outside MD land complete all as specified and directed.

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, Chajja etc fixed with self tapping screws complete all as specified and directed.

S & F framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

M&L for preparing of new steel surfaces of applying two coat of sythetic enamel paint over one coat of red oxide Zinc chrome any description ,over 10cm in width or girth not otherwise described

S & F in repair 4.8 mm thick plain/ sheet glass, ordinary quality cut to required size and shape for aluminium sliding windows/ ventilators/ doors etc including taking down joinery and refixing in the same position complete all as specified and as directed.

Chipping, removing carefully loose/damaged concrete incl plastering (total thickness upto 60mm ) from RCC surfaces of columns, beams,Chajas, soffits of slabs etc by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land, even including necessary scaffolding up to 24 m height complete all as specified Notes: (i) Hard concrete shall not be removed by force. (ii) Mode of measurement: superficial area of concrete will be measured

(i) M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hr between the coats, complete all as specified and directed. Note :- Mode of measurement: superficial area of concrete will be measured. (ii)M&L for Anticorrosive Treatment to Reinforcement using Corroseal - ZR of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces, complete all as specified and directed.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application, complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit upto 40mm thickness including levelling, profiling etc in two layers, each layer not exceeding 20mm, complete all as specified and directed.

Demolition of brick work or stone masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M & L for brick work with subclass 'B' bricks straight or curved on plan exceeding 6 mtr mean radius built in CM 1:4 complete all as specified and directed.

Dismantling wall and ceiling board and glass wool any thickness including snap grid complete at height n exc 6 m and M & L for aluminium anodised suspended false ceiling in the panels of size 600 x 600 mm with aluminium anodised angle 30 x30 x 2 mm fixed along the wall and main and cross tees of size 31.75 x 31.75 x 1.6 mm screwed along side of walls fixed with wooden plugs and hanging from existing slab/ steel truss including 6 mm dia GI wire suspended adjustable level from rafter purlins(length as per site requirement) including 595 x595x 4 mm thick non asbestos fibre cement building boards including cutting and making suitable opening for light fittings and applying 2 coats of synthetic enamel paint over a coat of primer etc complete all as specified and directed. Make Everest/ Saint Gobin

M & L for 18 to 20 mm thick machine cut kota stone slab as in flooring laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab including rubbing, rounding, nosing and polishing and over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed

M & L for 18 to 20 mm thick machine cut kota stone slab as in skirtings/risers laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab including rubbing and polishing and over and including 10 mm thick rendering in CM 1:6 complete all as specified and directed

Dismantling completely existing roof treatment (excluding cement screed bed ) including loosened cement plaster and exposing the top surface of RCC slab and removing rubbish, out of MD land complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on roof /parapet wall surfaces as in levelling course, finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

S&F vitreous china wash down water closet pan (Pedestal pattern) white, including matching plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium anodized hinging device and suitable size 'P' or 'S' trap and making all connections complete all as specified and directed.

S&F vitreous china urinal flat back, size of 465 x 355x 265 mm (minimum) white, with grating and union for discharge pipe (excluding flushing Cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal backing cement including CP spreader connections & push type angle lock complete all as specified and directed.

S&F in repairs 15 mm bore bib tap, cast copper alloy chromium plated, complete all as specified and directed.

S&F vitreous china squatting pan orissa pattern size 580x440mm white with integral foot rest including provision of lime concrete bedding and suitable size 'P' or 'S' trap and making all connections complete all as specified.

S&F wash hand basin, vitreous China, white, flat back type, of size 550x400mm, including CI brackets, cutting for and pinning in ends of brackets with coupling and including PVC connection, waste pipe key with brass union complete all as specified and directed.

Taking down 15mm bore GI tubing and connections including fittings, cleaning for refixing complete all as specified and directed.

All as per item No 54 above but 20mm bore

S&F 15mm bore GI tubing medium grade galvanised with all fitting and fixed complete to walls and ceiling or laid in floors complete all for the following sizes :-

All as per item No 56 above but 20mm bore

S&F in repairs or S&F 40mm bore uPVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls/floor complete all as specified and directed.

All as per item No 58 above but 75mm bore

All as per item No 58 above but 110mm bore

S&F in repairs or S&F 75mm bore PVC (SWR) branch piece, single (single 'Y') equal or unequal and fixed complete all as specified and directed.

All as per item No 61 above but 110mm bore

S&F in repairs or S&F 75mm bore uPVC (SWR) branch piece, double (double 'Y') equal or unequal and fixed complete all as specified and directed.

All as per item No 63 above but 110mm bore

S&F in repairs or S&F 75mm bore PVC SWR bends with or without access door (any radius) complete all as specified and directed.

All as per item No 65 above but 110mm bore

S&F PVC flushing tank, 10litres capacity, syphonic action type, high/low level, valveless, with PVC inlet ball valve, 40mm bore PVC flush pipe, float, suitable size MS brackets, PVC connection and brass unions including taking down of unserviceable / old CI / PVC flushing cistern complete all as specified and directed.

S&F in repairs chromium plated shower rose 125mm size with or without swivel joint for fixing in 15 dia pipe complete all as specified and directed.

S&F 15mm dia stop valves, cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe or for unions or for brass ferrule, as fixed in repairs complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nut of length 450 mm complete all as specified and directed by Engineer in charge.

M & L for APP modified roof treatment over roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications, complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160 gm/ Sq mtr using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 2 degree celcius. (x) Dimentional stability % change = Maximum 1%. (d) Over the membrane provided a finishing with solar reflective bitumen aluminium paint @ 0.10 Kg/ Sqm as prescribed by manufacturer.

Disconnecting existing water storage tanks upto and including 2000 litres, setting aside (or lowering if required) for repairs to roof below, and replacing (or hoisting if required), re-fixing in position and re-connecting on completion of roof work complete all as specified and directed.

M&L for PVC (SWR) 75 mm dia of out let kitchen/Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) including taking down the old one etc complete all as specified and directed.

Surface dressing not exc. 15cm deep in soft / loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25 cm hard/dense soil complete all as specified and directed.

Local bajari flling under floors including spreading,watering and levelling in layers n exc. 25 cm thick complete

M&L plain cement concrete in foundations filling and mass concrete type D-2 1:4:8 ( 40 mm graded aggregates) complete all as specified and directed.

M&L RCC M-30 (Design Mix) (using 20 mm graded aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc basement slabs, under-reamed piles and mass concrete etc all as specified and directed. Note : Design mix shall be carried out from approved lab such as IIT/ NIT/ SEMT Pune or any NABL approved lab or Govt college.

Use and waste formwork to sides of rough finished surface concrete foundations, footings, bases of columns, raft and beams sides and soffits (if any) of foundation and plinth beams; and similar work ; vertical or to batter, flat complete all as specified and directed.

M&L for RCC M30 (Design mix) (using 20 mm graded aggregate) in columns, pillars, piers, posts and struts etc complete all as specified and directed. Note : Design mix shall be carried out from approved lab such as IIT/ NIT/ SEMT Pune or any NABL approved lab or Govt college.

Use and waste forrnwork to sides of pillars. posts. struts. piers. columns and stanchions for rough finished surfaces of concrete, square, rectangular or polygonal etc complete all as specified and directed.

M&L for RCC M 30 (Design mix) (using 20 mm graded aggregate) in chajjas etc complete all as specified and directed. Note : Design mix shall be carried out from approved lab such as IIT/ NIT/ SEMT Pune or any NABL approved lab or Govt college.

Use and waste formwork to chullah hoods, chajjas, troughs and similar items including edges for flat for rough finished surface of concrete etc complete all as specified and directed.

M&L for RCC M30 (Design mix) (using 20 mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and directed. Note : Design mix shall be carried out from approved lab such as IIT/ NIT/ SEMT Pune or any NABL approved lab or Govt college.

Use and waste formwork to sides of soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal) or sloping for flat rough finished surfaces of concrete etc complete all as specified and directed.

S&F CRS steel 10 mm dia and over, cut to length,bent to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

All as per item No 87 but 6 mm to 8 mm dia and over, cut to length,bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

All as per ser item No 87 above but 5 mm over upto and including 10 mm dia in stirrups, spacers and binders.to complete all as specified and directed.

M&L for pre cast cement concrete block masonry with solid block of grade(C-5) having block density not less than 1800 Kg/cum, exc, 10cm in width and setting in CM 1: 6, complete all as specified and directed.

M&L plain cement concrete type B-1 , 1:2:4 ( 20 mm graded aggregate), 40 mm thick finished even and smooth w/o using extra cement complete all as specified and directed.

M&L 75 mm thick plain cement concrete in sub base of floors type D-2, PCC 1:4:8 (40mm graded aggregate) complete all as specified and directed.

M&L plain cement concrete type C-1 1:3:6 (using 20mm graded stone aggregates) as in plinth protections 75 mm thick finished even and smooth w/o using extra cement with joints 10 mm wide and filled with bitumen complete all as specified and directed.

M&L hardcore of gauge not exc. 63mm, deposited, spread and levelling in layers not exc. 15 cm thick, watered and rammed to true surface with broken stone or boulder complete all as specified and directed.

M&L for 3 mm thick (minimum) white cement based wall care putty in two coats on new or old surfaces of walls etc, finished even and smooth, complete all as specified and directed.

M & L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper with roller over one coat of primer, complete all as specified and directed.

S&F factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F standard aluminium section powder coated (minimum thickness of powder coating shall be 50 micron and colour shall be as approved by GE ) as in frame, shutters for doors, window / ventilators, partitions, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc complete all as specified and directed. Note:- Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. Cost of other items / accessories required for entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and wire cloth shall be measured and paid separately as supply only under respective items.

S&F aluminium anodised Grills of approved design with and including F/U channel for window, ventilators, balcony openging in architectual or rectangular type in existing building, including drilling as required in RCC sections, complete all as specified and directed. Note: The Grills shall be of Model DG-102/DG-104 of Make Deco or equivalent make as approved by the GE.

M&L 4 mm thick figured glass and glazing each pane complete all as specified and directed.

Supply only 5mm thick glass ordinary quality in each pane for aluminimum sliding window complete all as specified & directed.

S & F flushing cistern, 10 Ltrs. Capacity, PVC valveless, syphonic action type with dual flushing system, low level,white with inlet, ball valve,float and handle including brackets, flush pipe of polyethylene of low or high density or PVC, 32mm dia, complete all as specified and directed.

Supplying and laying of 20 mm CPVC pipes SDR 11 and plain CPVC SDR 11 fittings in walls/ floors complete all as specified and directed.

Supply & fixing 25mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S&F 110 mm bore uPVC (SWR) Bends with and without oval access door and also including rubber ring joints, complete all as specified and directed.

S&F 75 mm bore uPVC (SWR) junction piece complete all as specified and directed.

Supplying and fixing rotational moulded polythylene water storage tanks, double layered (ISI marked) of 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, including provision of necessary fittings for connecting the overflow, drain out, inlet and outlet pipes, complete all as specified and as directed.

S&F gunmetal gate valve, ISI marked with iron wheel head, screwed at both ends for iron pipe or ferrule of 25mm bore and provision of necessary fittings like unions, check nuts, etc, complete all as specified and as directed.

S&F 25 mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F brass chromium plated, shower rose, with 15mm bore with brass chromium plated shower arm with bend of 45 degree, complete all as specified and directed.

M&L ATT treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L ATT treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L ATT treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

S & F Fe 410 W (Gde E 250) Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) in staircase for manhole including distance pieces, cleats etc complete all as specified and directed.

S&F plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

M&L brickwork with sub class 'B' bricks in CM 1:4 straight curved on plan to any radius in half brick thick walls complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

Excavating over areas exc 1.5 m deep but n.exc 3.00 mtr depth and getting out in hard/dense soil complete all as specified and directed.

Surface excavation as in soft soil n.exc (not exceeding) 30cm deep and averaging 15 cm deep in getting out complete all as specified and directed.

Removing excavated material outside MD land complete all as specified and directed.

M&L plain cement concrete type C-2, 1:3:6 (40mm graded aggregate) 100 mm thick complete all as specified and directed.

M & L for PCC (1:3:6) Type C1 (using 20 mm graded stone aggregate ) in coping of including necessary form work finished even and smooth without using extra cement including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

M & L for PCC (1:2:4) Type B2 (using 20 mm graded stone aggregates) in surface channels / drains, including necessary formwork, finished to required shape complete all as specified and directed.

Extra for forming fair finished drain or channels 30 cm inner girth in Cement concrete using extra cement including forms, moulds mitred/ stopped ends etc. in manholes (inner girth only measured) complete all as specified and directed.

M & L for rendering 15 mm thick in CM (1:4) on fair faces of brickwork or concrete surface, finished even and smooth using extra cement including mixing of water proofing compound @ 3 % by wt of cement or as per manufacturer's instructions (supply only WPC shall be measured & paid separately) for internal surfaces of manholes complete all as specified and directed.

Supply only water proofing compound.

M&L for 150mm RCC pipe, class NP - 2 laid and jointed complete all as specified.

M&L for PCC (1:4:8) type D-2 using 40 mm graded stone aggregate for concrete bed to 150/200 mm dia drain pipes including packing, under haunching against the sides of pipes after they are laid and tested

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150 mm pipe complete all as specified and directed.

M&L PVC (SWR) gully trap 125/110mm setting and joining with solving cement.complete all as specified and as directed.

M&L PVC (SWR) floor trap plain with grating including joining with solving cement 75mm complete all as specified and as directed.

S & F 15mm bore CP stop cock cast copper alloy chromium plated screwed down high pressure screwed for iron pipe or for unions and fixed complete all as specified and as directed.

S & F 15mm bore CP bib taps cast copper alloy screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S & F 15mm bore CP pillar taps cast copper alloy type with capstain heads chromium plated, screwed down high pressure, screwed for iron pipe or for unions and fixed complete all as specified and as directed.

M & L concrete bed to drain pipes incl packing under and haunching against the slides of pipe after they are laid and tested in PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate for 110 mm bore pipe complete all as specified and as directed.

M & L rendering 15mm thick cement plaster on fair faces of brick work or concrete work in CM 1:3 finished to even and smooth surface (w/o using extra cement) incl mixing of internal water proofing compound as per manufacturer instruction (WPC to be measured and paid seperately as supply only).

M & L providing precast concrete in landings cover slabs (For Manholes etc) chullah hoods, chajjas, water troughs, managers, shelves and similar articles with plain with plain fair faces including chamfers weatherings throating etc and setting in mortar complete with joint match type B-1 (20mm graded aggregate) set in CM 1:4 complete all as specified and directed.

M & L 32 mm bore low density polythylene pipes of pressure rating 6kgf/cm2 fixed to walls, ceilings or in floors etc all as specified and directed complete

M&L providing cement concrete type C1 (1:3:6) in lintels cills, steps : seismic and other similar bands, plinth courses, lacing courses, parapets and rallings upto 60 cm in height, copings, kneelers, appex (20mm graded aggreagates) stones, bed plates over septic tank wal for placing cover slabl complete all as specified and as directed.

M&L machine pressed precast concrete interlocking paver block any shape and size of 60mm thickness, M-35 Grade, with grey cement and pigment including 25 mm thick sand cushioning complete all as specified and as directed.

M&L brass chromium plated Tubular towel rail 20mm dia, 60cm long between flanges with brackets complete all as specified and directed.

S & F Soap dish fixed to chromium plated brass screws complete all as specified and as directed.

S&F 2000 liters rotational moulded polyethylene water storage tanks (cylindrical vertical and closed top) hoisted and fixed in position all as specified in SSR Part-I including provision of necessary fittings for connecting the overflow, drain out, inlet and outlet pipes complete all as specified and directed.

M&L for sand cushioning by spreading in trenches fine dry river sand by gently by punning down manually as in cable protection all as specified and as directed by EIC. Note : Sand after punning down will be measured

Supply and laying precast concrete cable cover class LV ISI Marked, type-I, flat size 250mm x 150mm x 40mm laid in trenches all as specified.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, ISI marked electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 4 core. Including cable lugs of suitable size complete all as specified and directed.

S&F LED Flood Light fittings 100Watts including MS clamps including necessary bolts, nuts, washers, anchor fastners etc suitable for fixing security light all as specifed and as directed.

M & L for point wiring complete with proper colour coding using, 1100 Volts grade, 1.5 Sqmm, PVC insulated FRLS, unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked drawn in and including PVC casing caping (minimum 25mm width) fixed on the surfaces of wall, ceiling etc with all accessories, fittings, PVC junction boxes etc, sunk pressed steel boxes not less than 2 mm thick, 50 mm deep terminal boxes covered with 3mm thick laminated sheet top cover fastended with chromium plated brass screws, also including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multistranded copper conductor green colour as continuous earth wire connected to common earth dolly all as specified and directed for one light point /fan/bell point controlled by one one way switch, complete all as specified and directed.

-ditto- all as per item No 150 above but for One 2pin/3 pin socket outlet 5 Amps on same board complete all as specified and directed.

-ditto- all as per item No 150 above but for One 2pin/3 pin socket outlet 5 Amps on independent complete all as specified and directed.

M&L for point wiring using proper colour coding with 1100 Volts grade, 2.5 Sqmm PVC insulated, FRLS, unsheathed, wire confirming to IS-694, Part-II, ISI marked with multistranded copper conductor drawn in and including PVC casing caping (minimum 25mm in width) fixed on the surfaces with all accessories, fittings, PVC junction boxes etc, sunk pressed steel terminal boxes not less than 2 mm thick, 50 mm deep, covered with 3 mm thick laminated sheet top cover fastened with chromium plated brass screws, also including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, multistranded, copper conductor 1100 Volts grade, green color, continuous earth wire connected to common earth dolly for 15 Amps, 3 Pin, socket outlet independent, complete all as specified and directed.

S&F Switch Piano 5 Amps, 250 Volts, one way, flush type, complete all as specified and directed.

S&F Switch Socket combination 2 in 1 , 5 Amps, flush type, 5 Pin, 240 Volts, complete all as specified and directed.

S&F Switch Socket combination 2 in 1 , 5/15 Amps, flush type, 6 Pin, complete all as specified and directed.

S&F ceiling rose three terminal, 230 Volts PVC / Polyucarbonate body, complete all as specified and directed.

S&F fan regulator, electronic stepped (5 step), 230 volts, 100 watt, flush type and connecting-up, complete all as specified and directed.

S&F Retro LED tube rod 20 Watts, 230 volts, with high efficency PMMA diffuser, the rod shall be of Cat No. LTT8-20 of Crompton or Equivalent from Philips/Bajaj as approved by the GE, complete all as specified and directed.

S&F decorative box type LED light fitting, prewired complete with all accessories/inbuilt fittings, suitable for Retro LED tube rod 20 Watts, 230 volts, including PVC Square blocks 2 Nos for mounting the fitting, provision of three core copper conductor cable to connect from ceiling nose to light fitting, the fitting shall be of Cat No. IGP131LT8-16 of Crompton or equivalent from philips/Bajaj as approved by the GE. Note: Retro LED Light tube rod 20 Watt shall be paid separately under item No. 159

S&F Retro LED tube rod 08 Watts, 230 volts, with high efficency PMMA diffuser, the rod shall be of Cat No. LTT8-8 of Crompton or Equivalent from Philips/Bajaj as approved by the GE, complete all as specified and directed.

S&F decorative box type LED light fitting, prewired complete with all accessories/inbuilt fittings, suitable for Retro LED rod 08 Watts, 230 volts, including PVC Square blocks 2 Nos for mounting the fitting, provision of three core copper conductor cable to connect from ceiling rose to light fitting, the fitting shall be of Cat No DMLN1LT8-8 of Crompton or equivalent from philips/Bajaj as approved by the GE. Note: Retro LED Light tube rod 8 Watt shall be paid separately under item No. 161

S & F MCB DB, 8 way, SPN, double door, 240 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections, complete all as specified and directed. Note: Quoted rate shall also be deemed to include for provision of copper bus bar of 200 Amps rating.

S & F MCB, SP, 05 to 32 Amps, 240 Volts, 10 KA Breaking capacity, C-series, complete all as specified and directed.

S & F MCB, SPN, 05 to 32 Amps, 240 Volts, 10 KA Breaking capacity, C-series, complete all as specified and directed.

Supply & fix Ceiling fan of sweep 1200 mm sweep with frames, blades, provision of three core 1.5 Sqmm copper cable from ceiling rose to fan etc complete all as specified and directed.

Supply & fix Heavy Duty metallic Exhaust fan of sweep 300 mm sweep with frames, blades, mounting anchor fasteners, aluminium louvers made of aluminium sheet of 0.5 mm thickness, provision of three core 1.5 Sqmm copper cable from ceiling rose to fan, making opening of required in cement mortar brick wall/RCC for fixing of exhaust fan, making good the distrubed surfaces in CM 1:4, including scafolding if any required to carry out the work in building of height up to 20 Meters complete in all respects the Exhaust Fan Shall Conform to Cat no EXHD300-4-1 of Crompton or Equivalent from Bajaj

Supply& Laying fixing, connecting and testing steel water tubing of size 25mm bore, medium grade, galvanised, ISI marked, with screwed and socketed joints, in any length, including supply and fixing all fittings, fixed to walls or laid in trenches / floors etc complete all as specified and directed.

Taking down copper/ aluminum point wiring surface type, concealed type, flame proof type (Light/Fan/Socket or power) complete including fixtures and fittings such as switches, ceiling roses, pendants, regulators, socket, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces to walls floors etc.

Taking down of Old MCB DB of any size

M & L for point wiring complete with proper colour coding using, 1100 Volts grade, 1.5 Sqmm, PVC insulated FRLS, unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked drawn in and including PVC conduit concealed (minimum 25mm width) fixed on the surfaces of wall, ceiling etc with all accessories, fittings, PVC conduit, sunk pressed steel boxes not less than 2 mm thick, 50 mm deep terminal boxes covered with 3mm thick laminated sheet top cover fastended with chromium plated brass screws, also including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multistranded copper conductor green colour as continuous earth wire connected to common earth dolly all as specified and directed for one light point /fan/bell point controlled by one one way switch, complete all as specified and directed.

All as per item No. 171 above but wiring complete with 2.5 Sqmm for 3 pin 15A socket multipurpose on independent board

S&F in repairs Surface, hanging and wall mounted batten (Double side connection) suitable for LED tube 20/22 watts, 230 volts alongwith tube rod 22 watt (double side connection), including fixing mounting blocks 2 Nos, 15 mm MS conduit, 1.5 sqmm 3 core pvc insulated copper conductor cable including fixing arrangements complete . The fitting shall conform to Cat No. REGALBATTENT8UPTO1X22WDSBSWH for fitting and CRYSTAL 1213T8DSTL20WLED865SGLASS for tube rod of Havells /Wipro/Bajaj

S&F metallic body exhaust fans AC single phase 230/ 240 V of size 300 mm sweep 900 RPM with louvers & shutters. Make- Crompton Greaves /Havells/Bajaj/Khaitan

S&F building Security light fitting 30 Watt made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP66 protection and impact resistance of IK07including fixing arrangements with braket of suitable dia and taking down old rusted bracket fittings complete all as specified and directed . The fitting shall conform to Cat no ENDURAPEARLSL30WLED757SASYTOPCMP of Havells/ Wipro/Bajaj .

Supply & Fix MCB DB Double Door SPN 4 way 240 volts including connecting up with existing cable with new lugs.

M&L for earthing complete with M.S. galvanized earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below normal GL) with top edge of the earth plate not less than 1.5M below normal GL, connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of GI or steel incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 15 mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No. 3 of SSR Pt-I, 2009 specification.

Supply and fixing of GI pipe light grade of size 15 mm bore for laying in trenches/floors or walls including all fittings for fixing complete.

Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, ISI marked, electric power cables (heavy duty with stranded aluminium conductor 1100 volts grade of 2 core 10 sqmm including saddling in wall, cable duct with lugs & spacers connecting to LT panels etc complete including taking down old unserviceable cable.

M&L for cutting / boring of PCC/hard standing at a depth not more than 15 cm deep and 15 cm in breadth for passing earthing conductor and making good the disturbed surfaces with PCC (1:2:4) type B-0 or cement mortar (1:3) complete all as specified and directed.

S& F GI steel tubing medium grade 40 mm dia for laying in ground for road crossing etc for cable protection including necessary fittings , clamps for supports, etc complete all as specified and directed. Note : A sum of Rs 14,734.00 towards sch of credit shall be deducted to arrive the contract sum.

M/s Hari Om Construction

Parmatma Enterprises

M/s S.D Construction Co