Construction of Main Gate and renovation work in Hindu College Yamunanagar.

NS Item -Earth filling with the earth brought from outside the campus irrespective of 5km lead, including Loading, Unloading, transporting and laying in 20cm in layers, watering and consolidating complete in all respect and fully satisfaction of Engineer-in-charge. NS CP 0%

HSR Item 8.31-Providing and fixing facing extruded clay Tile (Glass Reinforced Clay Tiles (GRC)) any size any shade and design on wall with under layer of 12 mm thick cement plaster 1:3 and jointed with neat cement matched with pigment complete as per drawings, specifications and to the entire satisfaction of engineer- in- charge. HSR Rate(Rs.) 1972.00 Through Rate

HSR Item 6.16-Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). HSR Rate(Rs.) 6113.00 Through Rate

HSR Item 6.30.1-Centering and shuttering including strutting, propping etc. and removal of form for 1. Foundations, footings, bases of columns, etc. for mass concrete HSR Rate(Rs.) 156.00 Through Rate

HSR Item 6.33.6-Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note: Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. 6. Thermo-Mechanically Treated bars of grade Fe-500D or more HSR Rate(Rs.) 66.00 Through Rate

HSR Item 6.30.5-Centering and shuttering including strutting, propping etc. and removal of form for 5. Lintels, beams, plinth beams, girders, bressumers and cantilevers HSR Rate(Rs.) 296.00 Through Rate

HSR Item 7.21.2-Brick work with common burnt clay non- modular bricks of class designation 10.5 in foundation and plinth in: 2. Cement mortar 1:6 (1 cement : 6 coarse sand) HSR Rate(Rs.) 3968.00 Through Rate

HSR Item 6.30.16.1-Centering and shuttering including strutting, propping etc. and removal of form for 16.1. Edges of slabs and breaks in floors and walls Under 20 cm wide HSR Rate(Rs.) 114.00 Through Rate

HSR Item 8.27.2-Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 2. Granite work HSR Rate(Rs.) 230.00 Through Rate

HSR Item 8.32-ALUMINIUM COMPOSITE PANELS Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis and design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material and labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item , as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminium Composite Panel Cladding (including width of groove) shall be measured in sqm up to two decimal places. HSR Rate(Rs.) 2475.00 Through Rate

HSR Item 9.10.1-Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete : 1. With residual type petroleum bitumen of grade VG -10 HSR Rate(Rs.) 93.00 Through Rate

HSR Item 8.26.2.2-Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 2.2. Granite of any colour and shade Area of slab over 0.50 sqm HSR Rate(Rs.) 2776.00 Through Rate

HSR Item 9.11.1-10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: 1. With common burnt clay non-modular brick tile of class designation 10 HSR Rate(Rs.) 488.00 Through Rate

HSR Item 12.89-Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight up to 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. HSR Rate(Rs.) 701.00 Through Rate

HSR Item 12.99.4-Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 4. 150x10 mm HSR Rate(Rs.) 62.00 Through Rate

HSR Item 12.99.5-Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 5. 100x10 mm HSR Rate(Rs.) 46.00 Through Rate

HSR Item 12.102.1-Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 1. 125 mm HSR Rate(Rs.) 49.00 Through Rate

HSR Item 12.102.2-Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 2. 100 mm HSR Rate(Rs.) 43.00 Through Rate

HSR Item 12.103.2-Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 2. Twin rubber stopper HSR Rate(Rs.) 52.00 Through Rate

HSR Item 12.159.2-Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in- charge . (Cost of aluminium snap beading shall be paid in basic item): 2. With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) HSR Rate(Rs.) 922.00 Through Rate

HSR Item 13.3.2.1-Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: 2.1. Profile C Fixing with adjustable lugs with split end tail to each jamb HSR Rate(Rs.) 364.00 Through Rate

HSR Item 13.10.1-Providing and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 1. 4.0 mm thick glass panes HSR Rate(Rs.) 539.00 Through Rate

HSR Item 13.29.2-Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 2. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works HSR Rate(Rs.) 83.00 Through Rate

HSR Item 7.22.1-Brick work with common burnt clay non- modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : 1. Cement mortar 1:4 (1 cement : 4 coarse sand) HSR Rate(Rs.) 4404.00 Through Rate

HSR Item 9.18-Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. HSR Rate(Rs.) 147.00 Through Rate

HSR Item 9.57.2-Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 2. 110 mm diameter HSR Rate(Rs.) 200.00 Through Rate

HSR Item 9.58.2.2-Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 2.2. Single push fit Coupler 110 mm HSR Rate(Rs.) 74.00 Through Rate

HSR Item 10.4-Providing and laying of screed of 50 mm thick cement concrete 1:8:16 to be laid below the topping. HSR Rate(Rs.) 88.00 Through Rate

HSR Item 10.63.2-Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 2. Size of Tile 600x600 mm HSR Rate(Rs.) 987.00 Through Rate

HSR Item 10.67.2-Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement and matching pigments etc. complete. 2. Size of Tile 600x600 mm HSR Rate(Rs.) 1004.00 Through Rate

HSR Item 9.17.1-Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 1. In 75x75 mm deep chase HSR Rate(Rs.) 112.00 Through Rate

HSR Item 9.62.2-Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. : 2. 150 mm diameter HSR Rate(Rs.) 162.00 Through Rate

HSR Item 10.77-Providing and laying 80mm thick factory made cement concrete interlocking paver block of M -35 grade made by block making machine with strong vibratory compaction, of approved size, design and shape, laid in required colour and pattern over (BIS 15658:2006) and including 60mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. HSR Rate(Rs.) 637.00 Through Rate

HSR Item 11.5.3-12 mm cement plaster of mix : 3. 1:4 (1 cement: 4 fine sand) HSR Rate(Rs.) 113.00 Through Rate

HSR Item 11.6.1-15 mm cement plaster on the rough side of single or half brick wall of mix : 1. 1:4 (1 cement: 4 fine sand) HSR Rate(Rs.) 138.00 Through Rate

HSR Item 10.70.2-Extra for grouting the joints of floor tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. 2. Size of Tile 600x600 mm HSR Rate(Rs.) 140.00 Through Rate

HSR Item 11.4.2-10 mm thick cement plaster 2. 1:3 (1 cement: 3 fine sand) HSR Rate(Rs.) 114.00 Through Rate

HSR Item 11.55-Corbelling around almirah including 12mm thick cement plaster 1:6 HSR Rate(Rs.) 91.00 Through Rate

HSR Item 12.37.1-Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 1. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws HSR Rate(Rs.) 1400.00 Through Rate

HSR Item 11.76-Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. HSR Rate(Rs.) 37.00 Through Rate

HSR Item 11.54-Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. HSR Rate(Rs.) 31.00 Through Rate

HSR Item 11.64.1-Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1. New work (two or more coats) over and including water thinnable priming coat with cement primer HSR Rate(Rs.) 45.00 Through Rate

HSR Item 11.96.1-Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 1. New work (Two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) HSR Rate(Rs.) 85.00 Through Rate

HSR Item 12.33.2-Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. 2. With 12 mm mild steel U beading HSR Rate(Rs.) 697.00 Through Rate

HSR Item 11.60-Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. HSR Rate(Rs.) 59.00 Through Rate

HSR Item 11.78-Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. HSR Rate(Rs.) 31.00 Through Rate

HSR Item 11.77-Applying pink primer or aluminium priming coat on wood work including preparation of surface, Knotting and stopping etc. HSR Rate(Rs.) 19.00 Through Rate

HSR Item 12.50.1-Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 1. Fixed to steel windows by welding HSR Rate(Rs.) 91.00 Through Rate

HSR Item 12.99.3-Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 3. 200x10 mm HSR Rate(Rs.) 72.00 Through Rate

HSR Item 6.30.3-Centering and shuttering including strutting, propping etc. and removal of form for 3. Suspended floors, roofs, landings, balconies and access platform HSR Rate(Rs.) 208.00 Through Rate

HSR Item 6.30.6-Centering and shuttering including strutting, propping etc. and removal of form for 6. Columns, Pillars, Piers, Abutments, Posts and Struts HSR Rate(Rs.) 262.00 Through Rate

HSR Item 6.14.1-Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1. 1:1.5:3 (1 cement : 1.5 coarse sand (zone- III): 3 graded stone aggregate 20 mm nominal size) HSR Rate(Rs.) 4374.00 Through Rate

HSR Item 4.14.1-Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. All kinds of soil. HSR Rate(Rs.) 83.00 Through Rate

HSR Item 4.32-Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. HSR Rate(Rs.) 46.00 Through Rate

HSR Item 6.1.6-Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 6. 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) HSR Rate(Rs.) 2442.00 Through Rate

HSR Item 6.15.1-Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement : 1. 1:1.5:3 (1 cement : 1.5 coarse sand(zone- III) : 3 graded stone aggregate 20 mm nominal size) HSR Rate(Rs.) 5969.00 Through Rate

HSR Item 6.21-Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand(zone- III) : 3 graded stone aggregate 20mm nominal size). HSR Rate(Rs.) 5655.00 Through Rate

HSR Item 6.30.13-Centering and shuttering including strutting, propping etc. and removal of form for 13. Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards HSR Rate(Rs.) 458.00 Through Rate

HSR Item 12.98.2-Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 2. 250x16 mm HSR Rate(Rs.) 179.00 Through Rate

HSR Item 12.157.2.2-Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- charge. (Glazing, panelling and dash fasteners to be paid for separately) : 2.2. For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) HSR Rate(Rs.) 403.00 Through Rate

HSR Item 30.91-Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150mm dia up to 300mm HSR Rate(Rs.) 92.00 Through Rate

HSR Item 11.96.1-Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 1. New work (Two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) HSR Rate(Rs.) 85.00 Through Rate

HSR Item 30.16.1-Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. 1. With cement mortar 1:4 (1 cement : 4 fine sand) HSR Rate(Rs.) 176.00 Through Rate

HSR Item 11.60-Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. HSR Rate(Rs.) 59.00 Through Rate

HSR Item 5.14-Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. HSR Rate(Rs.) 35.00 Through Rate

HSR Item 5.70-Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in- charge, beyond 50 m initial lead, for all leads including all lifts involved. HSR Rate(Rs.) 86.00 Through Rate

HSR Item 9.10.1-Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete : 1. With residual type petroleum bitumen of grade VG -10 HSR Rate(Rs.) 93.00 Through Rate

HSR Item 9.57.2-Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 2. 110 mm diameter HSR Rate(Rs.) 200.00 Through Rate

HSR Item 10.73-Providing and fixing ceramic and Glazed tiles/ vitrified tiles/ of any size of approved make in floors / dados, laid in any pattern as specified over base of 3 mm thick adhesive of reputed brands as per IS specification 15477 -2004 using 5 Kg. adhesive per sqm area of tiles and jointed with white cement slurry mixed with pigment to match the shade of tiles excluding cost of tiles. HSR Rate(Rs.) 1247.00 Through Rate

HSR Item 10.63.2-Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 2. Size of Tile 600x600 mm HSR Rate(Rs.) 987.00 Through Rate

HSR Item 10.62-Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. HSR Rate(Rs.) 570.00 Through Rate

HSR Item 10.67.2-Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement and matching pigments etc. complete. 2. Size of Tile 600x600 mm HSR Rate(Rs.) 1004.00 Through Rate

HSR Item 10.4-Providing and laying of screed of 50 mm thick cement concrete 1:8:16 to be laid below the topping. HSR Rate(Rs.) 88.00 Through Rate

HSR Item 5.11-Demolishing mud phaska in terracing and disposal of material within 50 metres lead. HSR Rate(Rs.) 185.00 Through Rate

HSR Item 9.18-Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. HSR Rate(Rs.) 147.00 Through Rate

HSR Item 10.37.1-Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 1. 25 mm thick HSR Rate(Rs.) 790.00 Through Rate

HSR Item 8.29-Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete. HSR Rate(Rs.) 209.00 Through Rate

HSR Item 2.B0156- B0156. Common burnt clay F.P.S. (non modular)bricks tile class designation 10 HSR Rate(Rs.) 4465.00 Rate

HSR Item 9.58.5.2-Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 5.2. Bend 87.5° 110 mm bend HSR Rate(Rs.) 93.00 Through Rate

HSR Item 9.62.2-Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. : 2. 150 mm diameter HSR Rate(Rs.) 162.00 Through Rate

HSR Item 10.38-Providing and fixing of Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. HSR Rate(Rs.) 836.00 Through Rate

HSR Item 11.64.1-Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1. New work (two or more coats) over and including water thinnable priming coat with cement primer HSR Rate(Rs.) 45.00 Through Rate

HSR Item 9.11.1-10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: 1. With common burnt clay non-modular brick tile of class designation 10 HSR Rate(Rs.) 488.00 Through Rate

HSR Item 10.70.2-Extra for grouting the joints of floor tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. 2. Size of Tile 600x600 mm HSR Rate(Rs.) 140.00 Through Rate

HSR Item 9.17.1-Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 1. In 75x75 mm deep chase HSR Rate(Rs.) 112.00 Through Rate

HSR Item 2.B0146- B0146. Brick bats HSR Rate(Rs.) 357.00 Rate

HSR Item 12.114-Providing and fixing of roller blinds on windows complete with material and labour complete with push up and down arrangement as per approved design / colour and Engineer-in-charge. HSR Rate(Rs.) 2087.00 Through Rate

HSR Item 12.158.2-Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. 2. Pre-laminated particle board with decorative lamination on both sides HSR Rate(Rs.) 789.00 Through Rate

HSR Item 30.51-Taking out existing wooden door/window shutter, repair by cutting, painting etc. and refixing of repaired door/window shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. HSR Rate(Rs.) 131.00 Through Rate

HSR Item 5.42-Dismantling cement conglomerate / terrazzo floors 25 mm to 50 mm manually/ by mechanical means and disposal of material within standard lead as per direction of Engineer- in-charge. HSR Rate(Rs.) 97.00 Through Rate

HSR Item 9.47.3-Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main `T` runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross `T` of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main `T` at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross `T` of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main `T` runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer- in-charge. 3. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. HSR Rate(Rs.) 1176.00 Through Rate

HSR Item 10.60-Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. HSR Rate(Rs.) 685.00 Through Rate

HSR Item 30.94-Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, up to 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal and vertical tubes joint with cup and lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. HSR Rate(Rs.) 121.00 Through Rate

HSR Item 30.21-Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete HSR Rate(Rs.) 7.00 Through Rate

HSR Item 22.222.2.2-Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. 2.2. Single Socket Type B 110mm o/d SWR UPVC pipe lines laid complete HSR Rate(Rs.) 322.00 Through Rate

HSR Item 22.181-Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. HSR Rate(Rs.) 7.00 Through Rate

NS Item -Providing and fixing UPVC SWR fittings - IS 14735 (Prince - Ultrafit make and Equivalent ) (Floor Trap 110mm) Complete in all respect (Updated Feb 2024)

HSR Item 30.86-Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in- charge. HSR Rate(Rs.) 43.00 Through Rate

HSR Item 30.91-Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150mm dia up to 300mm HSR Rate(Rs.) 92.00 Through Rate

HSR Item 30.80.1-Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge. 1. Internal Work- Exposed on wall HSR Rate(Rs.) 1.00 Through Rate

HSR Item 30.89-Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge. HSR Rate(Rs.) 106.00 Through Rate

HSR Item 30.83-Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge. HSR Rate(Rs.) 28.00 Through Rate

HSR Item 9.58.4.2-Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 4.2. Single tee without door 110x110x110 mm HSR Rate(Rs.) 143.00 Through Rate

HSR Item 9.58.5.2-Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 5.2. Bend 87.5° 110 mm bend HSR Rate(Rs.) 93.00 Through Rate

HSR Item 22.105.1-Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 1. 15 mm nominal bore HSR Rate(Rs.) 512.00 Through Rate

NS Item -Providing and fixing in position 5mm thick looking mirror bevelled on sides fixing in position with necessary C.P. screws and washer and PVC moulding etc. complete

HSR Item 22.22.1-Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 1. White vitreous chinaware Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests HSR Rate(Rs.) 3493.00 Through Rate

HSR Item 9.58.4.1-Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 4.1. Single tee without door 75x75x75 mm HSR Rate(Rs.) 89.00 Through Rate

HSR Item 2.B1323- B1323. CP grating 100mm dia HSR Rate(Rs.) 89.00 Rate

HSR Item 22.103.2-Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 2. 20 mm nominal bore HSR Rate(Rs.) 294.00 Through Rate

HSR Item 22.101.2.1-Providing and fixing Unplasticised PVC connection pipe with brass unions : 2.1. 45 cm length 15 mm nominal bore HSR Rate(Rs.) 51.00 Through Rate

NS Item -Providing and fixing in position CP Jali 110mm dia complete in all respect (Make JAYNA, YKING or as approved in brand list of HPHC)

HSR Item 22.222.2.3-Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. 2.3. Single Socket Type B 90mm o/d SWR UPVC pipe lines laid complete HSR Rate(Rs.) 273.00 Through Rate

HSR Item 9.58.5.1-Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 5.1. Bend 87.5° 75 mm bend HSR Rate(Rs.) 59.00 Through Rate

HSR Item 22.14.2.1-Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 2.1. Flexible pipe 32 mm dia HSR Rate(Rs.) 57.00 Through Rate

HSR Item 22.25.1-Providing and fixing white vitreous chinaware flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1. One urinal basin with 5 litre white P.V.C. automatic flushing cistern HSR Rate(Rs.) 2844.00 Through Rate

HSR Item 22.1.4-Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 4. White vitreous chinaware Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap HSR Rate(Rs.) 1559.00 Through Rate

HSR Item 22.82.1-Cutting holes up to 30x30 cm in walls including making good the same: 1. With common burnt clay non-modular bricks HSR Rate(Rs.) 135.00 Through Rate

HSR Item 22.87.3-Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings This includes jointing of pipes and fittings with one step CPVC solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer in Charge. External work 3. 25 mm nominal outer dia Pipes HSR Rate(Rs.) 201.00 Through Rate

HSR Item 22.5-Providing and fixing white vitreous chinaware pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. HSR Rate(Rs.) 1104.00 Through Rate

HSR Item 22.104.1-Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 1. 15 mm nominal bore HSR Rate(Rs.) 346.00 Through Rate

HSR Item 22.108.1-Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 1. 15mm nominal bore HSR Rate(Rs.) 444.00 Through Rate

HSR Item 22.109-Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. HSR Rate(Rs.) 49.00 Through Rate

HSR Item 22.86.2-Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 2. 20 mm nominal outer dia Pipes HSR Rate(Rs.) 264.00 Through Rate

HSR Item 22.24.1-Providing and fixing white vitreous chinaware pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous chinaware flushing cistern and C.P. flush bend with fittings and C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1. W.C. pan with ISI marked white solid plastic seat and lid HSR Rate(Rs.) 4386.00 Through Rate

HSR Item 23.20-Fixing of LED Tube light/ 2*2 ft square panel fitting directly on wall /ceiling or false ceiling including making connections etc as required HSR Rate(Rs.) 67.00 Through Rate

HSR Item 23.8.11.10-FITTING AND ACCESSORIES 11.10. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Blanking plate HSR Rate(Rs.) 18.00 Through Rate

HSR Item 23.8.11.3-FITTING AND ACCESSORIES 11.3. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 1 way switch HSR Rate(Rs.) 82.00 Through Rate

HSR Item 23.8.11.5-FITTING AND ACCESSORIES 11.5. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 6 pin Socket HSR Rate(Rs.) 124.00 Through Rate

HSR Item 23.8.1.12-FITTING AND ACCESSORIES 1.12. Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Bakelite angle/straight button holder large size. HSR Rate(Rs.) 46.00 Through Rate

HSR Item 24.1.1-EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. HSR Rate(Rs.) 2721.00 Through Rate

HSR Item 23.8.10.5-FITTING AND ACCESSORIES 10.5. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 8 Modules HSR Rate(Rs.) 233.00 Through Rate

HSR Item 23.22.5.1-MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole HSR Rate(Rs.) 145.00 Through Rate

HSR Item 23.10-Erection of cabin fan complete with necessary earthling including carriage from PWD store to the site of work. HSR Rate(Rs.) 55.00 Through Rate

HSR Item 23.3.6.1-COPPER WIRING IN PVC CONDUIT (SURFACE/RECESS) 6.1. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm) HSR Rate(Rs.) 88.00 Through Rate

HSR Item 23.8.11.4-FITTING AND ACCESSORIES 11.4. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp Socket HSR Rate(Rs.) 82.00 Through Rate

HSR Item 23.7.6.2-PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. HSR Rate(Rs.) 32.00 Through Rate

HSR Item 23.8.1.5-FITTING AND ACCESSORIES 1.5. Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Ceiling rose flush/surface type HSR Rate(Rs.) 18.00 Through Rate

HSR Item 23.8.11.1-FITTING AND ACCESSORIES 11.1. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch HSR Rate(Rs.) 41.00 Through Rate

HSR Item 23.8.10.4-FITTING AND ACCESSORIES 10.4. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 6 Modules HSR Rate(Rs.) 186.00 Through Rate

HSR Item 23.22.5.4-MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.4. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. Double pole HSR Rate(Rs.) 677.00 Through Rate

HSR Item 24.1.6-EARTHING AND LIGHTENING ARRESTOR 6. Supplying and laying 25mm x 3mm G.I. strip at 0.5 metre below ground as strip earth electrode including soldering etc. as required. HSR Rate(Rs.) 47.00 Through Rate ¸¤HSR Ite

㔮挠牯⁥䄨浲⤮䠊剓删瑡⡥獒⤮㈠〵〮‰吠牨畯桧删瑡eᜀऀᤀሀᜀ戀ᨁࠁ午⁒瑉浥㈠⸳㈲㐮㔮䴭䍃⁂䐬卉剔䉉呕佉⁎佂剁卄ਬ䍍恂ⱳ删䍃恂ⱳ䌠䅈䝎⁅噏剅攠捴‮⸴⸵匠灵汰⁹湡⁤牥捥楴湯漠⁦潤扵敬搠潯⁲桳敥⁴瑳敥湥汣獯牵⁥楤瑳楲畢楴湯戠慯摲猠極慴汢⁥潦⁲䍍卂愠摮䔠䍌卂攠捴‮敲散獳摥椠慷汬椠据畬楤杮戠湯楤杮琠慥瑲⁨楷桴愠汬氠扡畯⁲湡⁤慭整楲污爠煥極敲⁤潴挠浯汰瑥⁥桴⁥潪⁢湩愠汬爠獥数瑣甠⁰潴琠敨攠瑮物⁥慳楴晳捡楴湯漠⁦桴⁥湅楧敮牥椭⵮桃牡敧漠⁦桴⁥潷歲‮偔⁎䉄䠠牯穩湯慴祴数䐠畯汢⁥潄牯㐠眠祡⠠㠠椠据浯湩⁧湡⁤瀳慨敳㐪漠瑵潧湩⥧䠊剓删瑡⡥獒⤮㈠〷⸷〰†桔潲杵⁨慒整 LJğЈ䠀剓䤠整㌲㈮⸲⸵ⴸ䍍䉃Ⱐ䥄呓䥒啂䥔乏䈠䅏䑒ⱓ䴊䉃獠‬䍒䉃獠‬䡃乁䕇传䕖⁒瑥⹣㔠㠮‮畓灰祬愠摮攠敲瑣潩景洠湩慩畴敲挠物畣瑩䈠敲歡牥†㐲⼰ㄴ‵⁖湩琠敨攠楸瑳湩⁧楤瑳楲畢楴湯戠慯摲椠据畬楤杮洠歡湩⁧敮散獳牡⁹潣湮捥楴湯㩳‭〴愠灭琠㌶愠灭‮䍍獂䘠問⁒佐䕌䠊剓删瑡⡥獒⤮ㄠ㤲⸱〰†桔潲杵⁨慒整 üŻЈ䠀剓䤠整㌲㔮㘮㌮䌭偏䕐⁒䥗䥒䝎䤠⁎塅卉䥔䝎倠䍖䴯⁓佃䑎䥕⁔䥐䕐匠剕䅆䕃刯䍅卅䕓⁄但⁒䱅䍅剔䍉䱁倊䥏呎⁓⸶⸳圠物湩⁧慭湩愠摮猠扵洠楡獮椠睴猠湩汧⁥潣敲映牯瀠慨敳愠摮渠略牴污眠物⁥湡⁤湯⁥楳杮敬挠牯⁥潦⁲慥瑲⁨楷敲倠䍖椠獮汵瑡摥䌠灯数⁲潣摮捵潴⁲慣汢⁥ㄱ〰嘠汯獴朠慲敤椠硥獩楴杮䴠⽓噐⁃潃摮極⁴瑥⁣獡爠煥極敲⹤ㄠ爠湵漠⁦楓敺㐠匠浱⡭⼱⸲㐲浭਩午⁒慒整刨⹳ 〱⸹〰†桔潲杵⁨慒整 ř½Ј䠀剓䤠整㌲㤮䔭敲瑣潩景攠桸畡瑳映湡椠硥獩楴杮漠数楮杮Ⰺ潣灭敬整眠瑩⁨敮散獳牡⁹慥瑲汨湩⁧景映湡椠据畬楤杮挠牡楲条⁥牦浯倠䑗猠潴敲琠桴⁥楳整漠⁦潷歲ਮ午⁒慒整刨⹳ 〱⸹〰†桔潲杵⁨慒整 ›—̈一⁓瑉浥ⴠ畓灰祬漠⁦㔱⁠硅慨獵⁴慦㌨㔷浭 〹‰偒ⱍ䠠慥祶䐠瑵⁹楷桴氠畯敶⁲桳瑵整⁲慭敫䌠潲灭潴牯攠畱癩污湥⁴獡瀠牥䠠䡐⁃牂湡⁤楬瑳圠呉佈呕䜠呓⠠华⸩ 

HSR Item 23.8.1.12-FITTING AND ACCESSORIES 1.12. Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Bakelite angle/straight button holder large size. HSR Rate(Rs.) 46.00 Through Rate

HSR Item 23.10-Erection of cabin fan complete with necessary earthling including carriage from PWD store to the site of work. HSR Rate(Rs.) 55.00 Through Rate

HSR Item 23.8.10.4-FITTING AND ACCESSORIES 10.4. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 6 Modules HSR Rate(Rs.) 186.00 Through Rate

HSR Item 23.8.11.1-FITTING AND ACCESSORIES 11.1. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch HSR Rate(Rs.) 41.00 Through Rate

HSR Item 23.8.10.5-FITTING AND ACCESSORIES 10.5. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 8 Modules HSR Rate(Rs.) 233.00 Through Rate

HSR Item 23.8.11.3-FITTING AND ACCESSORIES 11.3. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 1 way switch HSR Rate(Rs.) 82.00 Through Rate

HSR Item 23.8.11.4-FITTING AND ACCESSORIES 11.4. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp Socket HSR Rate(Rs.) 82.00 Through Rate

HSR Item 23.8.11.5-FITTING AND ACCESSORIES 11.5. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 6 pin Socket HSR Rate(Rs.) 124.00 Through Rate

HSR Item 23.20-Fixing of LED Tube light/ 2*2 ft square panel fitting directly on wall /ceiling or false ceiling including making connections etc as required HSR Rate(Rs.) 67.00 Through Rate

HSR Item 23.8.11.10-FITTING AND ACCESSORIES 11.10. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Blanking plate HSR Rate(Rs.) 18.00 Through Rate

HSR Item 23.22.5.4-MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.4. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. Double pole HSR Rate(Rs.) 677.00 Through Rate

HSR Item 23.22.5.1-MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole HSR Rate(Rs.) 145.00 Through Rate

HSR Item 23.8.1.5-FITTING AND ACCESSORIES 1.5. Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Ceiling rose flush/surface type HSR Rate(Rs.) 18.00 Through Rate

HSR Item 23.7.6.2-PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. HSR Rate(Rs.) 32.00 Through Rate

HSR Item 24.1.1-EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. HSR Rate(Rs.) 2721.00 Through Rate

㔮挠牯⁥䄨浲⤮䠊剓删瑡⡥獒⤮㈠〵〮‰吠牨畯桧删瑡eᜀऀᤀሀᜀ戀ᨁࠁ午⁒瑉浥㈠⸳㈲㐮㔮䴭䍃⁂䐬卉剔䉉呕佉⁎佂剁卄ਬ䍍恂ⱳ删䍃恂ⱳ䌠䅈䝎⁅噏剅攠捴‮⸴⸵匠灵汰⁹湡⁤牥捥楴湯漠⁦潤扵敬搠潯⁲桳敥⁴瑳敥湥汣獯牵⁥楤瑳楲畢楴湯戠慯摲猠極慴汢⁥潦⁲䍍卂愠摮䔠䍌卂攠捴‮敲散獳摥椠慷汬椠据畬楤杮戠湯楤杮琠慥瑲⁨楷桴愠汬氠扡畯⁲湡⁤慭整楲污爠煥極敲⁤潴挠浯汰瑥⁥桴⁥潪⁢湩愠汬爠獥数瑣甠⁰潴琠敨攠瑮物⁥慳楴晳捡楴湯漠⁦桴⁥湅楧敮牥椭⵮桃牡敧漠⁦桴⁥潷歲‮偔⁎䉄䠠牯穩湯慴祴数䐠畯汢⁥潄牯㐠眠祡⠠㠠椠据浯湩⁧湡⁤瀳慨敳㐪漠瑵潧湩⥧䠊剓删瑡⡥獒⤮㈠〷⸷〰†桔潲杵⁨慒整 LJğЈ䠀剓䤠整㌲㈮⸲⸵ⴸ䍍䉃Ⱐ䥄呓䥒啂䥔乏䈠䅏䑒ⱓ䴊䉃獠‬䍒䉃獠‬䡃乁䕇传䕖⁒瑥⹣㔠㠮‮畓灰祬愠摮攠敲瑣潩景洠湩慩畴敲挠物畣瑩䈠敲歡牥†㐲⼰ㄴ‵⁖湩琠敨攠楸瑳湩⁧楤瑳楲畢楴湯戠慯摲椠据畬楤杮洠歡湩⁧敮散獳牡⁹潣湮捥楴湯㩳‭〴愠灭琠㌶愠灭‮䍍獂䘠問⁒佐䕌䠊剓删瑡⡥獒⤮ㄠ㤲⸱〰†桔潲杵⁨慒整 üŻЈ䠀剓䤠整㌲㔮㘮㌮䌭偏䕐⁒䥗䥒䝎䤠⁎塅卉䥔䝎倠䍖䴯⁓佃䑎䥕⁔䥐䕐匠剕䅆䕃刯䍅卅䕓⁄但⁒䱅䍅剔䍉䱁倊䥏呎⁓⸶⸳圠物湩⁧慭湩愠摮猠扵洠楡獮椠睴猠湩汧⁥潣敲映牯瀠慨敳愠摮渠略牴污眠物⁥湡⁤湯⁥楳杮敬挠牯⁥潦⁲慥瑲⁨楷敲倠䍖椠獮汵瑡摥䌠灯数⁲潣摮捵潴⁲慣汢⁥ㄱ〰嘠汯獴朠慲敤椠硥獩楴杮䴠⽓噐⁃潃摮極⁴瑥⁣獡爠煥極敲⹤ㄠ爠湵漠⁦楓敺㐠匠浱⡭⼱⸲㐲浭਩午⁒慒整刨⹳ 〱⸹〰†桔潲杵⁨慒整 ř½Ј䠀剓䤠整㌲㤮䔭敲瑣潩景攠桸畡瑳映湡椠硥獩楴杮漠数楮杮Ⰺ潣灭敬整眠瑩⁨敮散獳牡⁹慥瑲汨湩⁧景映湡椠据畬楤杮挠牡楲条⁥牦浯倠䑗猠潴敲琠桴⁥楳整漠⁦潷歲ਮ午⁒慒整刨⹳ 〱⸹〰†桔潲杵⁨慒整 ›—̈一⁓瑉浥ⴠ畓灰祬漠⁦㔱⁠硅慨獵⁴慦㌨㔷浭 〹‰偒ⱍ䠠慥祶䐠瑵⁹楷桴氠畯敶⁲桳瑵整⁲慭敫䌠潲灭潴牯攠畱癩污湥⁴獡瀠牥䠠䡐⁃牂湡⁤楬瑳圠呉佈呕䜠呓⠠华⸩ 

HSR Item 24.1.6-EARTHING AND LIGHTENING ARRESTOR 6. Supplying and laying 25mm x 3mm G.I. strip at 0.5 metre below ground as strip earth electrode including soldering etc. as required. HSR Rate(Rs.) 47.00 Through Rate ¸¤HSR Ite

HSR Item 23.8.10.4-FITTING AND ACCESSORIES 10.4. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 6 Modules HSR Rate(Rs.) 186.00 Through Rate

HSR Item 23.8.1.12-FITTING AND ACCESSORIES 1.12. Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Bakelite angle/straight button holder large size. HSR Rate(Rs.) 46.00 Through Rate

HSR Item 23.8.11.3-FITTING AND ACCESSORIES 11.3. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 1 way switch HSR Rate(Rs.) 82.00 Through Rate

HSR Item 23.20-Fixing of LED Tube light/ 2*2 ft square panel fitting directly on wall /ceiling or false ceiling including making connections etc as required HSR Rate(Rs.) 67.00 Through Rate

HSR Item 23.22.5.1-MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole HSR Rate(Rs.) 145.00 Through Rate

HSR Item 23.8.1.5-FITTING AND ACCESSORIES 1.5. Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Ceiling rose flush/surface type HSR Rate(Rs.) 18.00 Through Rate

HSR Item 23.7.6.2-PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. HSR Rate(Rs.) 32.00 Through Rate

HSR Item 23.8.11.1-FITTING AND ACCESSORIES 11.1. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch HSR Rate(Rs.) 41.00 Through Rate

HSR Item 23.8.11.5-FITTING AND ACCESSORIES 11.5. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 6 pin Socket HSR Rate(Rs.) 124.00 Through Rate

HSR Item 23.8.11.10-FITTING AND ACCESSORIES 11.10. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Blanking plate HSR Rate(Rs.) 18.00 Through Rate

HSR Item 23.10-Erection of cabin fan complete with necessary earthling including carriage from PWD store to the site of work. HSR Rate(Rs.) 55.00 Through Rate

HSR Item 23.8.11.4-FITTING AND ACCESSORIES 11.4. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp Socket HSR Rate(Rs.) 82.00 Through Rate

Please Enable Macros to View BoQ information