SPL REPAIR OF WATER SEEPAGE OF WALL TILES AND KOTA STONE PLUMBING WORK IN BATHROOM AND ELECTRIC WORK IN BLDG NP P39 AND CERTAIN SANCTION WORKS UNDER AGE BR I OF GE (WEST) FEROZEPUR CANTT

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed.

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified.

Dismantling of floor hearth and wall tilling incl mortar beding removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches pillars etc but excluding ashlar facings dressed stone work and precast concrete articles complete all as specified and directed.

Taking down chowkkats or frames area but exceeding 1.5 Sqm and not exceeding 4.0 Sqm each ( without taking off shutters from the frames) complete all as specified and directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each complete all as specified and directed.

DemolItion and breaking up drain pipes 100 mm dia (Salt glazed ware,AC, PVC or reinforced concrete) set in cement mortar complete all as specified and directed.

Demolition and breaking up drain pipes 75 mm dia (Salt glazed ware,AC, PVC or reinforced concrete) set in cement mortar complete all as specified and directed.

Demolition of cement concrete in sunken portion any description and in any position not otherwise specifically provided complete all as specified and directed.

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegitation including roots near out let of RWP and OHT staging area or specifically ordered by Engineer-in-Charge in writing complete all as specified and directed.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified and directed.

M&L 50 mm thick cement concrete 1:3:6, type C-2 (using 20mm graded stone aggregate) as in plinth protection, shall be laid in 1:20 slope. The concrete shall be laid at a stretch not exceeding 3-meter in length. Joint gap between the adjoining slab, at corners and at junctions of wall shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen of grade 85/25 garde mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3-meter interval at corner and junction walls complete all as specified and directed..

M&L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade including laying of sand cushioning, etc, complete all as specified and as directed. Note :- Sand will be measured and paid for seperately.

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L Cement concrete (1:3:6), type C-1 (using 20mm graded stone aggregate) as in filling of steel chowkhats,bed blocks, coping etc including necessary form work complete all as specified and directed.

M&L Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and directed.

M&L Brick work with sub class B bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L Non skid coloured ceramic tiles of 7 to 8 mm thick , area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match over and including a screed layer of 15 mm thick in cement mortar 1:6 complete all as specified and as directed.

M&L Non skid coloured ceramic tiles of 7 to 8 mm thick , area of each tile exceeding 0.11 Sqm but not exceeding 0.18Sqm as in skirting/dado set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match and including backing with 10 mm thick in cement mortar 1:4 complete all as specified and as directed.

M&L Glazed coloured and cereamic tiles in vertical surfaces 450mmX300mm & 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including backing coat 10mm thick in cement mortar 1:4 for laying skirting dados and vertical surfaces complete all as specified and directed.

S&F Vitrified ceramic tiles 10mm thick (Square/rectangular)polished area of each tiles exceeding 0.36Sqm and not exceeding 0.42Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured (Light Shade)cement to match over and including 20 mm thick screed bed or bedding layer of cement mortar (1:6) for laying floor finishes complete all as specified and directed.

M&L light shade Vitrified tile 10mm thick polished, area of tile n exc.0.36 sqm as in Skirting set and jointed in cement slurry over and including 10mm thick screed in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

M&L Pressed steel frames made of 1.25mm thick MS sheet of profile 105mmx60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and directed.

All as per Srl item No 23 here-in-before but size 125mmx60mm with double rebate.

S&F Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified. Make: Rajshri or equivalent in approved makes.

S&F PTMT tower bolts, 200 mm long and fixed with steel screws complete all as specified and directed.

S&F PTMT butt hinge, 100mm long, fixed with steel screws with brass/bronze hinge pin complete all as specified and directed.

S&F PTMT handle 125mm long fixed with steel screws complete all as specified and directed.

S&F 35mm thick second class hard wood glazed and skelton shutters,open rebated and prepared to receive glass gauze,etc (without sash bars),edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) fitted to chowkat complete all as specified and directed.

S&F 35mm thick second class hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

S&F Factory made box type steel window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed.

S&F Factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed.

S&F Factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed.

S&F Mild steel framed work of as in grills/guard bars shouldered with steel window/ ventilator frames ccomplete all as specified and directed.

S&F 200mm long aluminium, anodised barrel tower bolts of extruded section, complete all as specified and directed.

S&F 150mm long aluminium, anodised barrel tower bolts of extruded section, complete all as specified and directed.

S&F 150mm Extruded aluminium alloy handle complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 300mm length,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F mild steel pressed handle ,oval type ,125 mm stoved enameled black and fixed with steel screw complete all as specified and directed.

S&F MS barrel tower bolts stone enamelled black with bright bolt,200mm length of bolt.

S&F 300mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including bolts and nuts complete all as specified and directed.

S&F butt hinges 100mm size exturded Alu. alloy with galvanised mild steel hinge pin anodised and fixed type B21 complete all as specified and directed.

S&F butt hinges 125mm size exturded Alu. alloy with galvanised mild steel hinge pin anodised and fixed type B-21 all as complete all as specified and directed.

S&F door closer hydraulically regulated designation No 2 universal type suitable for door shutter of 701 to 850mm thick in width and of weight between 36 to 60 kg of aluminium (Die cast body) in repairs complete all as specified and directed.

S&F 300mm mild steel rait rail rod pattern springs including roller and roller plate as fixed in repair complete all as specified and directed.

S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed.

M&L 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares not exceeding 0.50 Sqm complete all as specified and directed.

S&F Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

S&F anodised aluminium door window , ventilator etc fixed / sliding or pull and push type in shutter frames or shutters with two/three track sliding aluminium frame of Jindal /Hindalco (or) Equivalent make of approved size, including necessary joining cleats, glazing clips,powder coated aluminium snap beading, screws, including necessary anodised aluminium fittings like handles etc including taking down complete all as specified as per manufacturers instructions complete all as specified and directed. Note: EPDM Rubber beading/gasket measured and paid for seperatley.

S&F solar control film 25 micron reflective sticked to glass panes as per manufacturers instruction complete all as specified and directed.

S&F EPDM Rubber beading around glass in aluminium windows /ventilator shutters complete all as specified and directed.

S&F 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in square exceeding 0.5 sqm in each pane complete all as specified and directed.

S&F in repair to Hollow PVC wall lining consisting of 5mm thick single side prelam PVC sheet instead of plain colour sheet inclusive of solvent cement and fixing on PVC frame as per specified in MES schedule part-I & II complete all as specified and directed by Engineer in Charge .

S&F galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed by Engr-in-Charge.

S&F galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed by Engr-in-Charge.

S&F PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified and directed.

S&F in repair 15mm bore stop valves of cast copper alloy, screwed down, high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) fixed in repairs complete all as specified and directed.

S&F in repair 15mm bore Stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch orbutterfly handle,screwed bothends for ironpipe or forunions and fixed complete all as specified and directed.

S&F in repair 125mm dia CP brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass as in repair complete all as specified and directed.

S&F in repair PVC connection both end brass union and length 450 mm long for 15 mm bore pipe complete all as specified and directed.

S&F in repair Bib tap of CP brass, 15mm bore, fancy type screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, as in repair complete all as specified and directed.

S & F in repair of CP WHB mixer 15mm bore mixing and hot and cold water scrwed down for iron pipe and fixed. and waste system with 450mm long braided hoses complete all as specified and directed by Engineer in Charge.

S&F chromium plated fancy type15mm bore dia hot and cold wall mixer with provision for over head with 115mm long bend pipe one upper side connecting legs and wall flanges all as specified and directed. Note:-FLR 5219 N of make "Jaquar" or techno-commercially equivalent in approved makes.

S&F in repair Rotational moulded Polyethylene water storage tank of 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position including taking down old PVC water tank complete all as specified and as directed.

S&F in repair Rotational moulded Polyethylene water storage tank of 1000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position including taking down old PVC water tank complete all as specified and as directed.

S&F in repair 20mm bore PTMT ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed.

S&F in repair Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, fixed as in repair, complete all as specified and directed.

S&F in repair Vitreous china white wash down water closet (pedestal pattern) including PVC sheet cover, Jet and connection to drain or out going pipe and to flushing pipe anti-syphonage pipe etc, fixed as in repair, complete all as specified and directed.

S&F PVC waste pipe, 32mm bore suitable to waste coupling pipe attach with rubber ring joints fixed to waste coupling of sinks/WHBs. as fixed in repairs and all specified and directed.

S&F in repair Wash hand basin, flat back 550mmx400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified and directed.

M&L Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L rendering 15 mm thick cement plaster in cement mortar 1:4 on other than fair faces of brick/concrete work surfaces compound finished fair and even all as as specified.

M&L rendering 10mm thick cement plaster in cement mortar 1:6 on fair faces of brick or concrete surfasces finished even and smooth (without using extra cement ) complete all as specified and directed.

M&L Preparation of new plastered surfaces wall and applying two coats of Oil bound distember over a coat of primer complete all as specified and directed.

M&L Preparation of new plastered surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L 5mm thick rendering in cement mortar (1:3) on concrete surfaces, finished even and smooth without using extra cement as in ceiling complete all as specified and directed.

M&L Preparation of newly plastered surfaces of walls & applying three coats coats of white wash complete all as specified and directed.

M&L White wash in three coats on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and directed.

S&F 35mm thick second class hard wood plain framed, panelled shutters (two panel), with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commencial veneering on both faces. The size of rail and style as per IS:1003 (Part I), Kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 150mm long aluminium, anodised barrel tower bolts of extruded section, as fixed in repairs all as specified and as directed by the Engr-in-charge.

S&F 250mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed in repairs all complete all as specified and directed.

S&F 125mm Extruded aluminium alloy handle as fixed in repairs all as specified and as directed by the Engr-in-charge.

S&F 20mm ball brass valves high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed to union etc as fixed in repairs complete all as specified and directed.

S&F in repair gunmetal gate valve of 15mm dia with iron wheel head screwed both ends for iron pipe. complete all as specified and directed.

S&F gunmetal gate valve of 20mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Taking up or down 20mm steel/PVC tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 25mm steel/PVC tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F CPVC, medium grade, with all fitting and fixed to walls, ceilings or laid in floors 20 mm dia including taking up or down old tubing complete all as specified and as directed. Makes : Finolex or equivalent in approved makes.

S&F CPVC, medium grade, with all fitting and fixed to walls, ceilings or laid in floors 25 mm dia including taking up or down old tubing complete all as specified and as directed. Makes : Finolex or equivalent in approved makes.

S&F 20mm unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc any type of pipe complete all as specified and directed.

S&F 25mm unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed.

S&F Wash hand basin, flat back 550mmx400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified and directed.

S&F CP Soapdish Oval /squaretype as fixed in repairs and all as specified and directed.

S&F Vitreous china wash down water closet pan ( pedestal pattern) white with trap including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc ( Excluding fixing bolts , flushing cistern and flush pipe as fixed in repairs complete all as specified and directed.

S&F in repair PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified and directed.

S&F of white Vitreous China bowl urinal flat back, sizeof 465mm x 355mm x 265 mm white (minimum),with grating and union for discharge pipe (excluding flushing cistern, and flush pipe) including waste pipe 32mm dia bore fixed in repair complete all as specified and directed.

S&F PVC cabinet with mirror of size 350mmx450mm any Colour with all fixing arrangements as per manufacturer instruction complete all as specified and directed.

S&F in repair 15mm bore bib tap fancy type of chromium plated cast copper alloy brass, screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15mm bore pillar tap,fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F Two Way brass CP Bibcock with wall flange 50 to 65mm long(facilitate to fix the Halth faucet) (Make:Jaquar) CQTNO;23041/FLR 8041N) and Make: CERA catNo:F3002161 /F2002161 15 mm dia bore type with handle, screwed down, screwed for iron pipe or famale of quarter turn type as fixed complete all as specified and directed.

S&F 15 mm bore fancy type wall /WHB brass CP mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.

S&F hot and cold wall mixer With Over head shower type arrangement including bend pipe for over head shower with connecting legs and wall flanges as fixed all as specified and directed by Engineer-In-Charge.

S&F push tap 15 mm bore any colour of PTMT suitable for urinals screwed for iron pipe and fixed (minimum weight 15mm-47 gms) complete all as specified and directed.

S&F heavy duty Stainless Steel (AISI-304) Shower drain with Cockroach Trap (450mm x 75mm) including all fittings and fixed with white cement fixed complete all as specified and directed.

S&F in repair 15mm bore fancy type chromium plated Stop cock cast copper alloy screwed down, high pressure screwed both ends for iron pipe or union as fixed in repairs complete all as specified and directed.

S&F in repair chromium plated shower rose with or without swivel joints any size including fixing to steel pipe or union complete all as specified and directed.

S&F replacement of pressure JET for EWC including PVC connection and CP fitting as fixed all as specified and directed.

S&F Health faucet (ABS Body) with 8mm dia 1.00 m long flexible tube(PVC /stainless steel coated) and wall hook all as specified and directed by Engineer-in-Charge.

S&F in repairs heavy duty PVC waste pipe with waste fittings, 32 mm bore size for sinks,WHB etc with long screwed shanks and fly nuts complete all as specified and directed.

S&F in repairs heavy duty PVC waste pipe, 40mm bore suitable to waste coupling pipe attach with rubber ring joints fixed to waste coupling of sinks complete all specified and directed.

S&F in repair PVC connection 15mm x 600mm size with PTMT nuts complete all as specified and directed.

S&F towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gm) complete all as specified and directed.

S&F 75mm PVC(SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

S&F 110 mm dia PVC(SWR) pipes single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes laid in trenches complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 110 mm dia PVC (SWR) junction single, (single T) equal or uequal provided complete all as specified and directed.

S&F 75 mm dia PVC(SWR) pipes single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes laid in trenches complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 75 mm dia PVC (SWR) junction single, (single T) equal or uequal provided complete all as specified and directed.

M&L 15mm thick cement mortar (1:3) with WPC on walls as well as on sunken floor portion finished even and smooth using extra cement. Note:- WPC shall be measured and paid for separately.

Supply only water proofing compound.

M&L Applying evenly a tack coat of in dustrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed.

M&L PCC (1:5:10) type E-2 (using 40 mm graded stone aggrigate ) as in filling under sunken portion complete all as specified and directed.

M&L 25mm thick PCC(1:2:4) type B1 (using 20 mm graded stone aggregate) as in floor finished even and rough to receive top layer complete all as specified and directed.

S&F 150mm long aluminium, anodised barrel tower bolts of extruded section, as fixed in repairs all as specified and as directed by the Engr-in-charge.

S&F 125mm Extruded aluminium alloy handle all as specified and as directed by the Engr-in-charge.

S&F 100mm size Butt hinges, medium weight, cold rolled mild steel as fixed in repairs all as specified and directed.

S&F wall hung vanity type wash hand basin cabinet of size 805mmx450 mm with wash basin (white) complete all as specified and directed.

S&F 15mm dia Wash Hand Basin mixer (hot and Cold) (Table mounted Model) with extended spot type with 450mm braided connection pipe (Without POP UP) complete all as specified and directed.

S&F one piece Vitreous china wash down water closet pan (pedestal pattern)white/coloured cascade type640X360X690 (monolithic flush cistern type)Make: Jaquare Model NO:SLS WHT-6853S/CERA Cat No: s1013132 s single picece wc with PP seat cover ,Hinges fixing accessories set including flush cistern with S-Trap of size 220mm all as per manufacturing instructions and all as specified and directed.

S&F as in repair 15 mm bore fancy type angular valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed

S&F Two Way brass CP Bibcock with wall flange50 to 65mm long(facilitate to fix the Halth faucet) (Make:Jaquar) CQTNO;23041/FLR 8041N) and Make: CERA catNo:F3002161 /F2002161 15 mm dia bore type with handle, screwed down, screwed for iron pipe or famale of quarter turn type as fixed complete all as specified and directed

S&F Health faucet (ABS Body) with 8mm dia 1.00 m long flexible tube(PVC /stainless steel coated) and wall hook all as specified and directed by Engineer-in-Charge.

Supply & fixed replacement of pressure JET for EWC including PVC connection and CP fitting as fixed all as specified and directed.

S & F in repair 125mm dia CP grating doom with waste hole of PTMT (minimum weight 40 gm) complete complete all as specified and directed.

S&F 600mm long CP towel rail fixed to wall with steel screws and PVC rawl plug complete all as specified and directed.

S&F Stainless steel soap dish (not less than 1mm thick) of type as directed,fixed to walls with chromium plated brass screws with wooden/rawl plugs,in repair complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet galss shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F Toilet paper holder of brass, chromium plated or stainless steel fixed in repair to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F Brass chromium plated bottle trap 32mm dia for wash basins with inlet or outlet screwed for pipe or connections including necessary packing,union,cap and fixing complete all as specified and directed.

S&F in repairs PVC waste pipe with waste fittings, 32 mm bore size for sinks,WHB etc with long screwed shanks and fly nuts complete all as specified and directed.

S&F 20mm ball brass valves high pressure in repair with polythene float and flynut complete with all fitting screwed for iron pipe or brass ferrule and fixed to union, nipple, socket etc as fixed in repairs complete all as specified and directed.

S&F galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed by Engr-in-Charge.

S&F galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed by Engr-in-Charge.

Taking up or down 15 mm existing steel tubing and connections and Re fixing old steel tubing and connections in new or old position complete to walls and ceiling or laid in floors complete including cleaning the steel tubing all as specified and as directed.

All as per Srl Item No. 155 here in before but 20mm dia.

S&F in repair PVC connection 15mm x 600mm size with PTMT nuts complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches

S&F PVC (SWR) bends any radius 75mm bore with access door complete all as specified and directed.

M&L 15 mm thick rendering of mortar in cement mortar (1:4) with water proofing compound @3% by weight of cement or as per manufacturer instructions will be on surface to have a smooth surface for laying of water proofing membrane complete all as specified and directed. Note: WPC shall be measured and paid for separately.

Supply only water proofing compound.

M&L 80mm thick average consolidated thickness mud phuska on flat roof ncluding 25mm thick mud plaster complete all as specified and directed.

S&F 40 mm thick brick tiles laid on mud mortar and joints grouted flus in cement mortar(1:3) mixed with 5% of crude oil by wt of cement on mud phuska complete all as specified and directed.

M&L two coats of solar reflective bituminous aluminium Paint @ 0.1 kg per sqm over APP membrane complete all as specified and directed.

S&F Virified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed or bedding layer of cement mortar (1:6) for laying floor finishes complete all as specified and directed.

M&L for light shade Vitrified tile 10mm thick polished, area of tile not exceeding 0.36 Sqm as in Skirting set and jointed in cement slurry over and including 10mm thick screed in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

S&F of Glazed coloured and cereamic tiles in vertical surfaces 350mm x 250mm / 450mm x 350mm & 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over backing coat 10mm thick in cement mortar 1:4 for laying skirting dados and vertical surfaces complete all as specified and directed.

M&L preparing of old decorated surfaces (plastered or un-plastered) by brooming down and applying one coat of white wash to ceiling complete all as specified and directed.

M&L for washing rubbing down and stopping of distempered and painted surfaces and applying one coat of Oil bound Distemper complete all as specified and directed.

M&LPreparation of new plastered surfaces and applying two coats of cement base paint over a coat of alkaliresistant priming paint complete all as specified and directed.

M&L for applying wall putty of 1mm thick interior/exterior on wall surfaces finished smooth and even complete all as specified and directed.

M&L for preparing of old decorated surfaces (plastered or un-plastered) by brooming down and applying one coat of white wash on walls including cornices complete all as specified and directed.

M&L Preparation of old wooden or wood based surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M&L Preparation of old steel surfaces of any description not otherwise description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for two coats of synthetic enamel paint over shop coat steel surfaces complete all as specified and directed.

Demolition of Stone slabs and tiles laid bedded pointed in mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20 mm thick over 15 mm thick cement screed (1:6) base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish complete all as specifed and directed complete all as specified and directed

M&L for Kota stone slab 18-20 mm thick in skirting, etc over ang including 15 mm thick cement mortar (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish, complete all as specifed and directed.

M&L providing and laying 60mm thick factory made chamfered edge coloured cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed

M&L Plain cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregates) 75mm thick as in sub base of floor complete all as specified & directed.

S&F 150mm long aluminium, anodised barrel tower bolts of extruded section, all as specified and as directed by the Engr-in-charge.

S&F 150mm extruded aluminium alloy handle all as specified and as directed by the Engr-in-charge.

S&F 75 mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F of 40mm thick flush door shutter of solid core construction with block board core with lipping 2nd class hardwood/beading both faces are covered with decorative laminated type-I of thickness 0.9mm. Colour and pattern shall be approved by Engineer-in-Chargee.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staple etc complete all as specified.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Hacking out old broken glass from metel frame including punching or drilling out old glazing pins/ spring clips and providing and fixing new complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 300mm length,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified.

S&F 200mm long aluminium, anodised barrel tower bolts of extruded section, all as specified and as directed by the Engr-in-charge.

S&F 150mm Extruded aluminium alloy handle all as specified and as directed by the Engr-in-charge.

S&F mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed.

S&F 15 mm fancy type CP Stop cock with long shank and cup (concealed type) screwed down, high pressure with crutch handle both end screwed for iron pipe or union as fixed in repairs all as specified and directed.

S&F as in repair 15 mm bore fancy type angular valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed

S&F as in repair 15 mm bore fancy type bib taps long body cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair chromium plated shower rose with or without swivel joints any size including fixing to steel pipe with brackets and ends cups all as specified and directed.

S&F Corner glass shelves (set of 3 Nos) 225mm radious,6mm thick as per sample radious for bath room, fixed on suitable support complete all as specified and directed.

S&F in repairs PVC waste pipe with waste fittings, 32 mm bore size for sinks,WHB etc with long screwed shanks and fly nuts complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) bends ad provided with access door complete all as specified and as directed.

S&F PVC (SWR) bends any radius 75mm bore with access door complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.etc complete all as directed by Engr-in-Charge.

M &L Point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor, multi stranded of size 1.5 sqmm, single core, in and including new rigid non-metallic PVC conealed conduit, with all accessories as required such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green PVC insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) One light/fan/Bell Point controlled by one single pole one way switch.

(b) One 5 Amps socket outlet same board controlled by one single pole 5 Amps switch

(c) One 5 Amps socket outlet independent board controlled by one single poles 5 Amps switch

All as per Srl Item No 203 here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing complete.

S&F of Modular switch 6 Amp 2 way 1 module size complete all as specified and as directed by Engr-in-Charge.

S&F Modular Switch one way 6 A, 1 module complete all as specified and directed. Makes: - Precision/Anchor/Havells/Legrand

S&F Modular Switch one way 16 A, 1 module complete all as specified and directed. Makes - Precision/Anchor/Havells/Legrand

S&F Modular Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed. Makes: - Precision/Anchor/Havells/Legrand

S&F Modular Socket, 6A/16A - 2/3 pin combined 2 module complete all as specified and directed. Makes: - Precision/Anchor/Havells/Legrand

S&F modular Dummy plate complete all as specified and directed.

S&F Modular white cover plate including GI box inner, 3 module complete all as specified & directed. Makes: Precision/Anchor/Havells/Legrand

S&F Modular white cover plate including GI box inner, 4 modulecomplete all as specified & directed. Makes: Precision/Anchor/Havells/Legrand

S&F Modular white cover plate including GI box inner, 8 module complete all as specified &directed. Makes : Precision/Anchor/Havells/Legrand

S&F Modular step type regulator,120 W - 2 module complete all as specified and directed. Makes - Precision/Anchor/Havells/Legrand

S&F LED tube light fitting 18 Watts,4 feet long decorative ultra slim linear LED lighting fixture with extruded polycarbonate,environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

S&F of LED Wall bracket light 8 Watt decorative type (Warm white) enegy saving including 8 W LED Bulb complete all as specified and directed.

S&F LED Bldg Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. complete all as specified and directed.

S&F Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings including 10W LED Bulb complete all as specified and directed.

S&F exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed.

S&F Ceiling rose surface type, PVC/polycarbonate ,isolated, bakelite 65mm x 50mm, 3 terminals ISI marked complete all as specified and directed.

S&F Modular bell push piano flush type 6 Amps 1 module duly ISI marked complete all as specified and directed.

S&F bell ding dong AC 230 volts single pole complete all as specified and directed.

S&F sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type)fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed.

S&F MCCB 4 pole, 415 volts, 100 Amps, 36 kA, 50 Hz complete all as specified and directed.

S&F sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified and directed.

S&F MCB SPN, 40A - 63Amps, 240 volts, "C" series, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning complete all as specified and directed.

S&F MCB SP, 6A-32 Amps, 240 volts, "B" series, 10KA duly ISI marked, in the MCB DB, complete with connection testing and commissioning complete all as specified and directed.

S&F MCB SP, 40 Amps, 240 volts, "B" series, 10KA duly ISI marked, in the MCB DB, complete with connection testing and commissioning complete all as specified and directed.

S&F Sheet Metal Enclosures with Socket plug top and MCBs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 20 Amp complete all as specified and directed.

S&F in repair sub main wiring of 4 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor with earth wire of 4.0 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor including PVC conduit pipe 25 mm dia all as specified and directed. Note: Two run of single core 4 sqmm cable and one run single core 4.0 sqmm cable for earth wire and including conduit pipe 25 mm dia shall measured as one length).

M&L for sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2 x 6 sqmm drawn through in and including PVC Concealed with 1 x 6 sqmm PVC insulated copper conductor single core for continuous earthing complete including PVC conduit 25 mm dia complete all as specified and directed. Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated copper conductor single core,one run of PVC conduit shall be measured as single run).

M&L Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm & 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate and MS angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to spoxsed steel surfaces. excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009)

Supply, laying, testing and commissioning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sq. mm 4 Core complete all specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling, including spreading, levelling, watering and well ramming in layrs not exceeding 25cmin soft/loose soil complete all as specified and as directed.

Removing surplus soil to a distance not exceeding 50m and dpositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M&L for sand filling under floors, foundation or cable protection including spreding leveling in layer not exceeding 25cm thick complete all as specified and directed.

M&L Bricks; common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry width wise acrose the line of cable in trenches for protection of UG cable complete all as specified and directed.

M&L Mild steel galvanised iron pipe light grade (ISI marked) 40mm bore for passing of earth lead laid in trenches fixed to walls laid under floors, roads including all fittings i.e MS clamps nuts & bolts etc complete all as specified and directed.

Please Enable Macros to View BoQ information