Construction of volleyball Court and open Air Gym at Thanamandi (Constituency) 2nd time

Treatment of soil using chemical like round up for anti weeding laid in holes @ 300 mm c/c and consumpution @ 600 ml/ 10 Sqm

Consolidation of subgrade with power road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the subgrade

P/L and compacting stone agrregates of different sizes to form contour and elevation to the desired level as per the Drawing and instruction of Engineer Iincharge (size 40 mm /20 mm/10mm ) down black stone aggregate up to a depth of 300 mm from below primary backing . Layers of stone to be rolled as per desired slope and compaction using 8-10 tonnes Road roller over open area & pitch roller over areas with drainage pipes.

Supply and installation of artificial UV resistanat polyethylene synthetic grass with rigid monofilment yarn, minimum 40mm pile height. The turf should have minimum 40mm Pile Height made of POLYETHYLENE Monofilament & Pile weight minimum 900 g/m2 and above and stitched rate minimum @ 120/ mtr or above. The turf should have Dtex/Denier >=12300. The Primary backing of turf should be made of 100% POLYPROPYLENE, minimum weight 240 gram/m2 and above with Coating with Carboxylated SBR Latex appr. 1200 gr/m2 or Butadiene Styrene with weight of 900 g/sqm and total backing wt should not be less than 1140 g/sqm or as approved by FIFA under FIFA Quality/ FIFA Quality Pro Category. The Product shall be procured from FIFA Prefered Provider and FIFA Standard Licencee of European / American Make only The infill must be 15-20 Kg Silica Sand, minimum 15-20 kg & above SBR Rubber Granules. The line marking shall be stitched tufted material (Painted lines are not acceptable). The rate is inclusive of All applicable taxes, Lavies, Octoria, transportation loading/unloading complete except custom duty exemption & Including Maintenance of 3 years by way of brushing and adding infill as and when required.

Providing of Fixing Height Adjustable Fixed Volley Poles 4 INCH with Net and Anteena

Excavating, supplying and filling of local earth (including royalty)by mechanical transport also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge All kinds of soil :

Providing and laying of Gabion of mechanically woven, double twisted hexagonal wire mesh Gabion Type: Zinc coated mesh type 100 mm x 100mm, woven diagionally. Mesh wire dia 2.70, salvage wire dia 3.40 mm lacing wire dia 2.20 mm of GI wire including all leads lifts and carriages and cost of Stone and Gabion wire crates. The gabions shall have partions made of same material and each compartment shall be of size 1.2m x 1.00m

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Centring and shuttering including strutting, propping etc. and removal of form work for Foundations, footings, bases of columns etc. for mass concrete.

Centering and shuttering including strutting, propping etc. and removal of form work for Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Steel work welded in built up section framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer.

Providing and fixing G.I Chain link Fabric fencing of required width in mesh size 50x50mm including strengthening with 2mm dia wire or nuts, bolts and washers as required complete as per direction of Engineer in Charge Made of G.I wire dia 4mm

Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 liter/10sqm over and including priming coat of water exterior paint applied @ 2.20kg/10sqm)

Applying priming coat: With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Supply and laying of PVC insulated and PVC sheathed / xlpe aluminium power cable of 1.1 KV grade of following sizes on surface / direct in ground including sand cushioning protective covering and refilling the trench as required as per direction of Engineer Incharge 16 sq. mm 2 core

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required.For 6 way, Double door SPN MCBDB

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole and neutral 32 Amp

LED Flood Light, powder coated pressure die cast aluminium (System lumen efficacy >135 lm/Watt) Supplying, Installation, Testing & Commissi oning of Flood Light, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85% Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, 54 DELHI SCHEDULE OF RATES (E&M)-2025 EMI-EMC as per CISPR-15, lenses for beam angle 30 deg-120deg as per the application and the project requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). 200 watt

Designing, Supply, installation and third party testing and commissioning of Solar Standalone street light system with MPPT charge controller and IP 65 protection and Luminous Flux of 4500 lm & lumen efficacy of 150 lumen/watt or more, lithium ferro phosphate battery pack, MONO Crystalline type Solar board with 60W or more PV Module & Solar board voltage of 18 V having movement and Lux Sensor, with 2000 cycle Battery charging & discharging cycles with Color rendering index (CRI) >70 & Dimmable Configurability. Note: Firm has to submit originallity certificate of material from OEM or Authorized Distributor with 05 years of warranty.

Provision for supply and Installation of Pedestal for Inaguration made with 4 mm thick ACP Sheet as base of size 4' x 6' and Acrylic Inaguration Plate Acrylic sheet cover as per direction of Engineer Incharge

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Arm wheel: Providing and fixing Arm wheel in a pair with below specifications: Dimensions(LxWxH): 850 x 800 x 1800 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main pilar with wheel frame of NB 50mm. All pipes must be (G.I.) ‘C’ Class Pipes. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be shall be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly with chemical bolting.Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

ELLIPTICAL EXERCISER Providing and fixing of Elliptical exerciser with below specifications: Dimensions (LxWxH): 1200 x 550 x 1600 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 80mm (G.I.) ‘C’ Class Pipe. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Handle bars shall be provided with high end quality rubber grips. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly with chemical bolting. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

DOUBLE CROSS WALKER Providing and fixing of Double cross walker with below specifications: Dimensions (LxWxH): 1600 x 600 x 1600 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). Foot support frame of 96 x 46 x 3mm MS rectangular pipe. All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly with chemical bolting. Self-Explanatory stainless-steel label shall be fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

TRIPLE TWISTER Providing and fixing of Triple twister with below dimensions: Dimensions (LxWxH): 1300 x 1300 x 1650 mm Shall be Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Handle Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. Handle frame spokes of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). Foothold plate of made of MS Sheet Metal of 3mm thickness. All Pipes shall be powder coated with 80–120-micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness & Base plate of 12 mm thickness. Once the concrete is set, the equipment shall be fixed on to it. High tensile steel with galvanized nut bolts shall be used for assembly with chemical botling. Self-Explanatory stainless-steel label shall be fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

DOUBLE PULL CHAIR Providing and fixing of Pull chair in a pair with below specifications: Dimensions (LxWxH): 2400 x 800 x 2000 mm Shall be Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Seat main frame of NB 50mm (G.I.) ‘C’ Class Pipe, Pipe connecting main post with handle frame of NB 65mm (G.I.) ‘C’ Class Pipe. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all the welding points prior to finishing. Handle bars to be provided with high end quality rubber grips. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated to be used used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment shall be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is to be fixed on to it and nuts and bolts to be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly with chemical botling. Self-Explanatory stainless steel label to be fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

AIR SWING Air swing in a pair with below specifications: Dimensions (LxWxH): 1150 x 900 x 1250 mm To be Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Leg Support frame of NB 50mm (G.I.) ‘C’ Class Pipe. Handle support frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all the welding points prior to finishing. Handle bars shall be provided with high end quality rubber grips. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of MS Sheet Metal with rounded edges to prevent impact and injury. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be to be fitted with inbuilt limiters to prevent unwanted movements. The equipment is to be fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is to be fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly with chemical botling. Self-Explanatory stainless steel label fixed on equipment for ease of use Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

LEG PRESS Providing and fixing leg press in a pair with below specifications: Dimensions (LxWxH): 2000 x 600 x 1800 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly with chemical botling. Self-Explanatory stainless steel label fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Knee Hip Raise (Chin Ups / Dips / Push Ups): CHIN UPS: Instrumental in building upper body muscles especially that of the back and shoulder. Wide and narrow grips provide for various permulations of popular exercise. DIPS: Soft handgrips for dipping using your own body weight. A very strong and robust exercise fortriceps, shoulders and back muscles. PUSH UPS: Appropriately heighted rolled bars that relieve unneces-sary stress from wrist and forearms. Allows user to dip lower for a more complete arm, chest, shoulder and back workout. Dimensions (LxWxH): 1400 x 1100 x 2100mm. Fabricated with base frame of NB 50mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. Leg support of NB 32mm (G.I.) ‘C’ Class Pipe and other support of NB 25mm (G.I.) 'C' Class Pipes (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters), All pipes shall be powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs, Zinc primer paint is applied at all welding points prior to finishing,The equipment is fixed on ground with concrete of minimum strength M-20 and J shaped welded bolts of 18mm thickness,Once the concrete is set, the equipment is fixed on to it.High tensile steel with galvanized nut bolts shall be used for assembly with chemical botling. Self-Explanatory stainless steel label fixed on equipment for ease of use. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Horse rider station Horse rider station with below specifications: Dimensions (LxWxH): 1000 x 600 x 1100 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. Handle support frame of NB 50mm (G.I.) ‘C’ Class Pipe and other pipes of NB 32mm & NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of NB 32mm (G.I.) ‘C’ Class Pipe. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly with chemical botling. Self-Explanatory stainless steel label fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Rowing machine Rowing machine with below specifications: Dimensions (LxWxH): 1250 x 800 x 1150 mm Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. Handle support frame of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). All Pipes shall be powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. All joints of pipe shall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate of12 mm thickness have cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated shall be used in the equipment manufactured. The equipment shall be fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M- 20 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts shall be covered with base plate cover. High tensile steel with galvanized nut bolts shall be used for assembly. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

Providing and fixing of Durable SBR TILE flooring (Outdoor) Protects floor from damages by dumbbells and iron gym material Thickness:25 mm Dimensions: 490mm x 490mm SBR-25 SBR TILE of approved make and colour and as per directions of engineer in charge incl cost and carriage incl necessary jointing by cement concrete or adhesives including forming of at least 0.15m x 0.15m or above (width x thickness) block on all sides of tiles as per dierctions of engr incharge including all finishing in all the respects complete job . Rates Inclusive of all Carriage, Taxes, Fixing & Maintenance of same upto 3 years as and when required.

carriage of Sand & stone aggregate by mt

Please Enable Macros to View BoQ information