Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹42.9 LAccepted-AOC PEMASAR ROAD WARD NO 04 UDASAR BIKANER RAJ 334001 | BIKANER | BIKANER | RAJASTHAN | 334001 | 1 | Accepted-AOC Lowest Accepted Bidder | |
| 2 | 2₹43.7 L+₹6,346.34 (0.15%)Rejected-Finance B 22 152 STREET NO 1 14 BABA FARID NAGAR BATHINDA 151001 | BATHINDA | PUNJAB | 151001 | 2 | Rejected-Finance Lowest Bidder is M/S Subham Enterprises | |
| 3 | 3₹49.3 L+₹5.6 L (12.9%)Rejected-Finance | 3 | Rejected-Finance Lowest Bidder is M/S Subham Enterprises |
Tender Value
₹50 L
EMD Value
₹1 L
Closing Date
23 Jan 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Col Avik Saxena, CWE Bikaner
HQ CWE Bikaner, Mil Stn Bikaner, PIN-334001
Comprehensive maint and periodical service of MD Accn for Zone D under AGE B/R-II at Bikaner Mil Stn under GE (N) Bikaner
2022_MES_570480_1
CA No CWE BKN-Token No. 62/2022-2023
Open Tender
Civil Works
Item Rate
270 days
Bikaner
As per Tender Documents
7 documents required · 7 mandatory
₹1,000
GE (N) Bikaner
₹1 L
Yes
17 Mar 2023
21 Dec 2022
30 Jan 2023
21 Dec 2022
23 Jan 2023
11 Jan 2023
21 Dec 2022 - 28 Dec 2022
Amount
Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description complete all as specified & as directed.
Demolition of unreinforced cement concrete of any description and in any position (not otherwise specifically provided for in this Schedule, complete all as specified & as directed.
Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.
Taking down cement plaster or cement lime plaster, terrazo etc on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and as directed.
Dismantling of brick tiles or roof tiles or terracing tiles single layer on roofs, complete all as specified and as directed. Note : Tiles shall be dismantled carefully and stacked properly including segregating the serviceable & unserviceable tiles as directed. Serviceable tiles shall be reused under the respective item of this Schedule.
Demolition of lime concrete of any description over roof, complete all as specified and as directed.
Dismantling of stone slabs and tiles of any description or any thickness in floors, dado etc, laid bedded and pointed in any mortar, complete all as specified & as directed.
Dismantling boarding, any description, fixed in any position with nails complete all as specified & as directed.
Dismantling timber scantlings 40 sqcm and over in section, in any position complete all as specified and as directed.
Dismantling structural steel work including doors, gates but excluding framed trusses etc, complete all as specified and as directed.
Taking down shutters (including fittings & fixtures) of any description exceeding 1.0 sqm and not exceeding 2.00 sqm each and refixing in the same opening after resecuring or easing & adjusting of shutters complete all as specified and as directed.
Taking down shutters (including fittings & fixtures) of any description exceeding 1.0 sqm and not exceeding 2.00 sqm each, complete all as specified and as directed.
Taking down chowkat or frame with shutters (including fittings & fixtures) area not exc 1.5 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.
Taking down chowkat or frame with shutters (including fittings & fixtures) area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.
M&L for anti-termite treatment to the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified & as directed.
M&L for anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified & as directed.
M&L for PCC 1:5:10 type E2 using 40 mm graded crushed stone aggregate as in sunken floor complete all as specified and as directed.
M&L for PCC 1:3:6 type C0 (using 12.5mm graded crushed stone aggregate) as in filling up chowkat/frame hollows and similar works complete all as specified and as directed.
S&F in repairs GI plain wire of 3.15mm dia complete all as specified and directed.
S&F in repairs SS cloth hanger with atleast 5 Nos hook in each hanger complete all as specified and directed.
M&L for brick work with old size Fly Ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 complete all as specified and as directed.
M&L for brick work with old size Fly Ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.
M&L for 5cm thick sand stone slab in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc not exc 2m in length, punched dressed on face and along exposed edges, self faced on the other side and set and pointed in cement mortar 1:4, complete all as specified and as directed.
M&L for Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in cement mortar 1:3 complete all as specified & as directed.
Supply and fixing factory made 35mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & as directed.
Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24(a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & as directed.
S&F factory made 25mm thick flush shutter, solid core construction, with block board core and plywood face panels, both faces covered with decorative face veneer with lipping to match complete all as specified and as directed.
S&F factory made 30mm thick flush shutter, solid core construction, with block board core and plywood face panels, both faces covered with decorative face veneer with lipping to match complete all as specified and as directed.
S&F second class hard wood in scallting of clean swan wood for frame and fixed with nails and screws complete all as specified and as directed.
S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube, fixing in opening as per specifications complete all as specified and as directed.
S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed..
M&L for 12mm thick prelaminated particle board (ISI marked), exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work/hinges as in cupboard shutters, shelves, Kitchen cabinets etc with & including necessary 18/19mm wide & 6mm thick Teak wood beading / edging / lipping fixed with nails to particle board complete all as specified & as directed.
M&L for 18/19mm thick prelaminated particle board (ISI marked), exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work/hinges as in cupboard shutters, shelves, Kitchen cabinets etc with & including necessary 18/19mm wide & 6mm thick Teak wood beading / edging / lipping fixed with nails to particle board complete all as specified & as directed.
M&L for 19mm thick Block boards, grade 2 quality, interior grade, commercial type, for cup board fixed with screws to timber framework with decorative film mica face veneer on both side with proper cover fillet of standard hard board 4.5mm thick boarding plain on side with butt joints with including block complete all as specified and as directed.
S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws complete all as specified and as directed.
S&F butt hinges of size 100mm medium weight, cold rolled mild steel (ISI marked) including welding to angle iron frame where required complete all as specified and as directed.
S&F butt hinges of size 100mm extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21 complete all as specified and as directed.
S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed.
S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed.
S&F 150 mm long mild steel barrel tower bolts, stove enameled black with bright bolts and fixed complete all as specified and as directed.
S&F 150mm size aluminium handle, cast type, powder coated, complete all as specified & as directed.
S&F 125mm size aluminium handle, cast type, powder coated, complete all as specified & as directed.
S&F mild steel pressed handle, 150 mm size, oval type, stove enameled black complete all as specified and as directed.
Supply and fixing hasp and staple of size 100mm aluminium anodized safety type with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified.
S&F in repairs Cup board knob mild steel 40mm dia complete all as specified and directed.
S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.
M&L for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty & fixed, complete all as specified and as directed.
S&F in repairs Aluminium extruded section body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851-1000mm in width & weight between 61 to 80 Kg, complete all as specified and directed.
Supply and fixing brass mortice lock, vertical type, size 100mm, 4 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified & as directed.
S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.
S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, fixed in repairs, complete all as specified and as directed.
S&F rubber gasket of thickness atleast 2.5mm thick and width 60mm for wooden doors to cover to gap between door and floors etc complete all as specified and directed.
S&F in repairs stainless steel drapery rod of 25mm inner dia & 1.6mm wall thickness (in lengths as directed) with & including stainless steel sockets & decorative finial at both ends and pair of stainless steel brackets & stops fixed at both ends with PVC rawl plug & steel screws on walls/beam complete all as specified & as directed.
S&F factory made pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, complete as specified & as directed.
S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, complete as specified & as directed.
S&F factory made pressed steel frames of size 75x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, made out of mild steel sheet of 1.25 mm thickness, complete as specified & as directed.
S&F factory fabricated pressed steel frame/box windows, ventilators with glazed and fly proof shutters provided to size and dimensions as specified & shown on drawing No. BTD-888R Sheet No. 1/5 to 5/5 & BTD-889 Sheet No. 1/4 to 4/4 with & including MS grill, MS fillets, pintol hinges, tower bolts, MS handles, peg stays, MS lugs, locking arrangement, dash through bolt where required, etc complete all as specified & as directed. Notes : (i) PCC for filling in frames, glass, wire gauge and painting shall be measured & paid for separately under respective items. Provision of all other items as shown & specified on drawings shall deemed to be included in quoted rate of this item. (ii) The quoted rate shall deemed to include provision of cutting holes of suitable depth in walls for inserting lugs etc and making good dismantled portion in PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate and CM (1:3).
S&F in repairs 125mm steel window handle left/right complete all as specified and directed.
S&F factory made steel window with side hung shutters including box type hinges with steel handles and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified & as directed.
S&F factory made steel window with side hung shutters including box type hinges with steel handles and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified & as directed.
M&L for Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. not exceeding 10 kg each brackets, conforming to Fe.290. Gde-E-165 complete all as specified and directed.
S&F aluminium work powder coated of any colour as approved (thickness of powder coating not less than 50 micron) as in frame & shutters for doors, windows, ventilators, wall partitions, including joining cleats, glazing clips, snap beading, screws for fixing, etc., all aluminium sections as per relevant IS, complete all as specified & as directed. Note : Glass and rubber neoprene packing / rubber gasket shall be measured and paid for separately as “Supply only” under respective item of this Schedule.
S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge
Supply only rubber neoprene packing / rubber gasket of required size & profile suitable for aluminium frame work in doors, windows, etc complete all as specified & as directed.
S&F aluminium window and ventilator shutters, powder coated of any colour as approved (Thickness of powder coating not less than 50 micron), side hung type without sash bars, aluminium sections including necessary joining cleats, glazing clips, powder coated aluminium snap beading, screws, complete all as specified & as directed. Note : Glass and rubber neoprene packing / rubber gasket shall be measured and paid for separately as “Supply only” under respective item of this Schedule.
S&F in repairs steel rolling shutters, thickness of laths 1.00 mm, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete, push pull or manual type, with safety lever locks mild steel with 4 levers, complete all as specified and as directed.
S&F in repairs Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed.
S&F in repairs Ball bearing for rolling shutters complete all as specified and as directed.
M&L for running welding in repairs, thickness of metal to be welded exc 6 mm but not exc 9mm, complete all as specified & directed.
M&L in repairs welding not exceeding 2.5cm in length and not exceeding 6mm thick of metal complete all as specified and directed.
S&F in repairs 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling, complete all as specified & as directed.
Supply only liquid water proofing compound ISI marked complete all as specified.
M&L for 10mm thick plaster (screed bed) over roof slab in CM 1:4, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished even & smooth without using extra cement, complete all as specified and as directed. Note : Supply only integral liquid water proofing compound shall be measured and paid for separately.
M&L for rendering 10mm thick in cement mortar 1:3 on fair faces of brick masonry or concrete surfaces of walls in Sunken portion, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified. Note : Supply only integral liquid water proofing compound shall be measured and paid for separately.
M&L for removal of loose concrete and cleaning the surfaces and filling the cracks with Polymer modified mortar using Dr Fixit Pidicrete URP or other equivalent product as approved by GE and thereafter applying two coats of Dr Fixit Bathseal WPC or other equivalent product as approved by GE in Sunken areas complete all as per manufacturer’s instructions, specified & directed. Note : Where contractor desire to use equivalent product of Dr Fixit Pidicrete URP and Dr Fixit Bathseal WPC, he shall submit the technical literature of equivalent products to establish the equivalency of products to the entire satisfaction of GE and both products shall be of same manufacturer as approved by the GE.
M&L for 400 micron thick heavy duty Polythene film (White) over roof slab laid on a coat of bitumen primer @ 0.50 Kg/Sqm and the like, complete all as specified and directed.
M&L for cleaning of all loose dirt and dust from roof and priming the surface with one coat of cold applied bituminous primer @ 0.40 litre/sqm and provide a layer of APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick, reinforced with polyester non woven fabric (weighing not less than 150 gms/sqm) laid on primed surface complete all as described in Para 11.44.5 of SSR Part-I, complete all as specified and as directed. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps.
M&L for Lime concrete terracing in roof with minimum thickness at edge 40mm and increasing uniformly towards ridges to obtain a chain slope of (1:40) as described in Para 11.27.2 of MES Schedule Part-I complete all as specified & as directed. Note : For lime concrete mudia kankar (Source : NAL) and Kolayat coarse sand in lieu of brick aggregate and surkhi respectively as specified in MES schedule Part-I shall be used.
M&L for 40mm thick brick tiles, joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement, laid on roof over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed.
All as per serial item No. 80.00 here-in-before but except brick tiles complete all as specified & as directed. Note : Old serviceable brick tiles retrieved from serial item No 6.00 here-in-before shall be used under this item.
M&L for 75 mm thick PCC (1:3:6) type C2 using 40 mm graded crushed stone aggregate as in sub base, surface finished even and smooth without using extra cement, complete all as specified and as directed.
M&L for 75 mm thick PCC (1:2:4) type B2 using 40 mm graded crushed stone aggregate as in flooring, surface finished even and smooth without using extra cement, complete all as specified and as directed.
M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded crushed stone aggregate as in flooring, leveling course, etc, surface finished fair and even, complete all as specified and as directed.
M&L for machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 20mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed.
M&L for machine cut Kota stone slab 16 to 18mm thick on vertical surfaces such as dado, skirting etc. laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab with true & uniform joints including rubbing and mirror polishing complete all as specified & as directed.
M&L for 18 to 20mm thick Granite (of any type) machine cut slab of approved shade (table rubbed and polished) with true & uniform joints as in steps, jambs, pillars, window cills, cooking platforms & like and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick screed bed (bedding layer) in CM 1:4 with cement slurry @ 3 Kg/Sqm complete all as specified & as directed. Note : The exposed edges of granite stone slab shall be made full round & polished to mirror finish and rate quoted shall deemed to include this provision.
M&L for 16-18mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & as directed.
Moulding/Rounding (making full moulding) to edges of kota/marble stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified & as directed.
M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.
M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.
M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e 450mm x 300mm or as directed), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.
M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.
M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished even and smooth without using extra cement complete all as specified and directed. Note :- Plinth protection shall be of width as directed and shall be laid with an outward slope of 1:30 in alternative bays not exceeding 4 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).
M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.
M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete all as specified and directed.
M&L for rendering 5mm thick in cement and sand mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.
M&L for Flush pointing in cement and mortar 1:3 on roof tiles to bricks laid flat or brick tiles in pavings, floors, roofs, aprons etc, including racking joints/ pointing to brick work complete all as specified & as directed.
M&L for forming jambs etc in cement mortar 1:4 to opening (to foregoing item), with stone including cutting, toothing and properly bonding into old work, including facing and pointing (if necessary) to match existing work complete all as specified & as directed.
M&L for preparation of newly plastered / unplastered surfaces of walls & applying two coats of white wash complete all as specified and directed.
M&L for preparation of newly plastered / unplastered surfaces of ceilings & applying three coats of white wash complete all as specified.
M&L for preparation of old surfaces (plastered or unplastered) of walls including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of white wash complete all as specified & as directed.
M&L for preparation of old surfaces (plastered or unplastered) of ceilings including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of white wash complete all as specified & as directed.
M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 3mm thick white wall care putty complete all as specified & as directed.
M&L for preparation of old decorated plastered surfaces of walls and applying one coat of oil emulsion distemper (OBD) of approved shade/tint complete all as specified & as directed.
M&L for preparation of old decorated plastered surfaces of ceiling and applying one coat of oil emulsion distemper (OBD) of approved shade/tint over & including white wall care putty on walls for filling the undulations as required complete all as specified & as directed.
M&L for complete removal of existing treatment of painted wall & pillars etc by mechanical equipment like electric wall sander including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including white wall care putty on walls for filling the undulations as required complete all as specified & as directed.
M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 3mm thick white wall care putty on ceiling complete all as specified & as directed.
M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of alkali resistant priming paint complete all as specified & as directed.
M&L for preparation of old decorated plastered surfaces of walls & applying one coat of cement base paint of approved shade/tint as approved by GE complete all as specified & as directed.
M&L for complete removal of existing treatment of painted wall & pillars etc by mechanical equipment like electric wall sander including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of cement base paint of approved shade/tint over a coat of alkali resistant priming paint on walls over & including white wall care putty on walls for filling the undulations as required complete all as specified & as directed.
M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of cement base paint of approved shade/tint over a coat of alkali resistant priming paint on walls complete all as specified & as directed.
M&L for preparation of old surfaces by complete removal of existing treatment of painted surfaces of walls including pillars and applying two coats of exterior emulsion/weather proof acrylic emulsion paint (exterior grade) of approved shade/tint over a coat of primer complete all as specified & as directed.
Hacking out old broken glass any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.
S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified & as directed.
Supply only plain sheet glass 5.00 mm thick ordinary quality in required sizes, not exc 0.5 sqm in each pane, complete all as specified and as directed (for aluminium windows/ventilators).
S&F 3mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified & as directed.
M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified & as directed.
M&L for complete removal of existing treatment on wooden surface of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint including preparation of surfaces over and including a coat of pink primer and finishing with wooden putty complete all as specified & as directed.
M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified & as directed.
M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.
M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified & as directed.
Dismantling carefully and taking up or down existing unserviceable/serviceable steel water tubing and connections of 15mm bore complete all as specified and as directed.
M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed.
Fixing/Laying only, jointing and testing old serviceable galvanized steel water tubing medium grade of 15mm bore obtained serviceable vide serial item No. 123.00 here-in-before including cleaning the pipe from inside & outside properly including rust & mud removal, with & including new fittings and fixed to walls and ceilings or laid in floors in new or old position complete all as specified and as directed. Note : The quoted rate shall deemed to include new GI fittings (ISI marked). Old fittings shall not be used.
Dismantling carefully and taking up or down existing unserviceable/serviceable steel water tubing and connections of 20mm bore complete all as specified and as directed.
M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed.
Fixing/Laying only, jointing and testing old serviceable galvanized steel water tubing medium grade of 20mm bore obtained serviceable vide serial item No. 126.00 here-in-before including cleaning the pipe from inside & outside properly including rust & mud removal, with & including new fittings and fixed to walls and ceilings or laid in floors in new or old position complete all as specified and as directed. Note : The quoted rate shall deemed to include new GI fittings (ISI marked). Old fittings shall not be used.
Dismantling carefully and taking up or down existing unserviceable/serviceable steel water tubing and connections of 25mm bore complete all as specified and as directed.
M&L for galvanized steel water tubing medium grade of 25mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed.
Fixing/Laying only, jointing and testing old serviceable galvanized steel water tubing medium grade of 25mm bore obtained serviceable vide serial item No. 129.00 here-in-before including cleaning the pipe from inside & outside properly including rust & mud removal, with & including new fittings and fixed to walls and ceilings or laid in floors in new or old position complete all as specified and as directed. Note : The quoted rate shall deemed to include new GI fittings (ISI marked). Old fittings shall not be used.
M&L for Gun metal globe or gate valve, with iron wheel head, screwed both ends, ISI marked for 20mm bore pipe fixed as in repairs complete all as specified and directed.
M&L for Gun metal globe or gate valve, with iron wheel head, screwed both ends, ISI marked for 25mm bore pipe fixed as in repairs complete all as specified and directed.
Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.
Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.
Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 2000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.
Disconnecting existing serviceable rotational moulded polyethylene water storage tank, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and refixing in position of capacity not exc 500 litres including cleaning & removing all scale & dirt etc from tank with gunny bags, cleaning with fresh water and bleaching powder, including writing "date of cleaning" and next due date in bold capital letters exc 4cm in height of capacity utpo 500 litre complete all as specified and as directed.
S&F in repairs PVC water tank lid for 500 litre capaicty including all locking arrangements, nuts, bolts etc for fixing complete all as specified and directed. Note : Lid can be of any description such as openable or roundable threaded.
S&F in repairs PVC water tank lid for 1000 litre capaicty including all locking arrangements, nuts, bolts etc for fixing complete all as specified and directed. Note : Lid can be of any description such as openable or roundable threaded.
S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, (excluding flushing cistern and flush pipe) with CI 'P' trap of long arm of suitable size including connection to flush pipe, antisyphonage pipe etc, and fixed as in repairs provision of lime concrete bedding minimum 150mm thick (lime concrete ratio 1:2:5) complete all as specified and as directed.
S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic WC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete all as specified & as directed.
S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white, size 365x655x765 mm (minimum) including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with UF seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, complete all as specified & as directed. Make : Jaquar, Cat Part No. LYS-WHT-38851P or equivalent in makes mentioned in Appendix 'B' here-in-after.
S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified & as directed.
S&F in repair 32mm dia brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified & as directed.
S&F in repairs complete internal cistern fitting for floor mounted coupled WC complete all as specified & as directed.
S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & as directed.
S&F in repairs vitreous china wash hand basin, white, oval shape with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & as directed.
S&F in repairs vitreous china urinal, half stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT spreader, PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia, complete all as specified and as directed.
S&F sink with drainage board made of stainless steel 1mm thick for Kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to brick wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 40mm dia waste pipe of polythelene of low or high density, 40mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as specified and as directed including taking down old unserviceable sink with fittings.
S&F in repairs stainless steel Kitchen plate rack of overall minimum size 900mm x 600mm and 250mm deep, with partitions for small/large plates etc, made out of stainless steel sheet 24 Gauge, fixed with rawl plug and CP steel screws complete all as specified and as directed.
S&F in repairs PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified & as directed.
S&F in repairs 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes, complete all as specified & as directed.
S&F in repairs mixer for mixing hot & cold water for wash hand basin, cast copper alloy, with dual capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' & 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe suitable for 15mm bore, complete all as specified as directed. Make : Cat Part No. ‘G4914A1’ of ‘Parryware’ / Cat Part No. ‘F2002461’ of ‘Cera’ / Cat Part No. ‘ARI-39119’ of ‘Jaquar’ / Cat Part No. ‘9250’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.
S&F in repairs wall mixer, telephonic type, brass, chromium plated, fancy type, with capstan head handles with lettered 'hot' and 'cold', screwed down high pressure, including CP brass wall flanges and necessary extension nipples screwed for 15mm bore pipe connection, complete all as specified as directed. Make : Cat Part No. ‘CON-217KN/ CON-267KN/ CON-271KN’ of ‘Jaquar’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.
S&F 15 mm bore spray jet, brass chromium plated with and including 1.5 metre long PVC flexible reinforced pipe for EWC complete all as specified & as directed.
S&F in repairs 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type with crutch or butterfly, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & as directed.
S&F in repairs 15 mm bore bib tap, brass, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, including CP brass wall flange, complete all as specified & as directed. Make : Cat Part No. ‘ARI-39037’ of ‘Jaquar’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.
S&F in repairs 15mm bore Stop valve, fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union complete all as specified & as directed.
S&F in repairs 15mm bore Angle cock, fancy type and cup of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union complete all as specified & as directed.
S&F in repairs Shower rose, round type, brass, chromium plated, Fancy type, 100 mm dia (minimum) with arm 225mm long (Minimum) or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe of 15mm bore or union complete all as specified and as directed. Make : Cat Part No. ‘T9809A1’ of ‘Parryware’ / Cat Part No. ‘F7010212AB’ of ‘Cera’ / Cat Part No. ‘BOS-87’ of ‘Prayag’/ Cat Part No. OHS-1989 of Jaquar or equivalent in makes mentioned in Appendix ‘B’ here-in-after.
S&F in repairs tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and as directed.
S&F in repairs Towel ring round brass chromium plated with round flange (Cat Part No ACN-1121BN of make – Jaquar or equivalent in makes mentioned in Appendix 'B' here-in-after) fixed on wall with PVC rawl plug & cadmium plated brass screws complete all as specified & as directed.
S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 150mm, fixed in floor, complete all as specified and as directed.
S&F in repair Mirror cabinet (PTMT) of size 450mm x 350mm with 5mm thick high quality mirror, seamless finish, light weight, high strength, fixed on wall with cadmium plated brass screws, complete all as specified & as directed. Make :- Prayag (Cat Part No. 557) or equivalent in makes mentioned in Appendix ‘B’ here-in-after.
S&F in repairs brass chromium plated Health Faucet with 8mm dia & 1.20m long stainless steel braided flexible tube and wall hook suitable for fixing to supply pipe of 15mm bore complete all as specified and as directed. Make :- Cat Part No. ‘ALD-573’ of ‘Jaquar’ / Cat Part No. ‘T9875A1’ of ‘Parryware’ / Cat Part No. ‘F8030301’ of ‘Cera’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.
Supply and fixing 100 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors, fixed in repairs, complete all as specified and as directed.
Supply and fixing 75 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors, fixed in repairs, complete all as specified and as directed.
Supply and fixing 100 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed in repairs, complete all as specified and as directed.
All as per serial item No. 170.00 here-in-before but except cast iron pipe 100mm bore complete all as specified and as directed.
Supply and fixing 75 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed in repairs, complete all as specified and as directed.
All as per serial item No. 172.00 here-in-before but except cast iron pipe 75mm bore complete all as specified and as directed.
S&F stack clamp made out of MS flat 50mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 100mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified & as directed.
S&F stack clamp made out of MS flat 50mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 75mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified & as directed.
S&F in repairs 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.
S&F in repairs 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed.
S&F in repairs 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.
S&F in repairs 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed.
S&F in repairs 100mm bore cast iron Tee (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed.
S&F in repairs 100mm bore cast iron bends (any radius), with duck's foot or heel rest with oval access door complete all as specified & as directed.
S&F in repairs 100mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified & as directed.
S&F in repairs 75mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified & as directed.
Supply and fixing cast iron vent cowl for 100 mm bore CI pipe complete all as specified.
M&L for extra over cast iron pipe & fitting 100mm bore providing lead joints in lieu of cement joints complete all as specified and as directed.
M&L for extra over cast iron pipe & fitting 75mm bore providing lead joints in lieu of cement joints complete all as specified and as directed.
S&F in repairs cast iron floor trap of 100 mm bore, with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4), complete all as specified & as directed.
S&F in repairs cast iron floor trap of 75 mm bore, with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4), complete all as specified & as directed.
S&F cast iron 'P' & 'S' trap of 100 mm bore complete all as specified & as directed.
S&F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls with stainless steel patti complete all as specified & as directed.
S&F 110mm bore PVC (SWR) bend, any redius complete all as specified & as directed.
S&F in repairs 100mm dia stainless steel grating fixed with white cement with outer square frame complete all as specified & as directed.
S&F in repairs 100mm dia with hole Stainless steel grating fixed with white cement with outer square frame complete all as specified & as directed.
S&F in repairs 32mm coupling for wash hand basin complete all as specified and as directed.
S&F in repairs 32mm dia PVC flexible waste pipe, for WHB complete all as specified and as directed.
S&F in repairs 40mm dia PVC flexible waste pipe, for Sink, complete all as specified and as directed.
S&F in repairs 40mm coupling for Kitchen Sink complete all as specified and as directed.
S&F plastic dividing strips, 1.5mm thick, 38mm wide, inserted in position, conform to design complete all as specified and as directed.
M&L for writing letters/ Bldg Nos or figures (Block, Roman, Italic or India) n exc 30cm height using synthetic enamel paint white or black circular painted, black ground complete all as specified and as directed.
Removing up rooting vegetation growth building roof top/sides of walls of any height and n exc. 30 cm girth and applying suitable acid for burning of roots in the RCC / Brick wall surface including stacking of serviceable material and disposal of unserviceable material to a distance n exc. 50m and clearing the site and making good of the disturbed surfaces in brick work in cement and sand mortar 1:4 and cement plaster in cement and mortar 1:4, or pointing in the same mortar surface area n exc 1.50 sqm each place complete all as specified and directed.
HARPREET SINGH CONTRACTOR
vikas builders
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .