PROVN OF VITRIFIED TILE AND INTERLOCKING TILE AT SANGHA AUDITORIUM AND DRAINAGE SYSTEM AND RETAINING WALL FOR TOK AND SPECIAL REPAIR TO BLDG NO T 09 HOT AND COLD ANCY AND REPLACEMENT OF CEILING FAN AGAINST BER AT AKHNOOR UNDER GE NORTH AKHNOOR

Amount

(i) Determining of SBC by manual boaring 100mm dia bore hole up 6 mtr depth and performing SPT as per IS-2131 of 1996 collection of disturbed/undisturb soil sample take for test. In test case of gravely strata as refusal the open pit of 2 mtr depth if bldg work as directed by Engr-in-Charge and submission test report in triplicate. (ii) Conducting of necessary as test per relevant IS-Code/NBC 2005/SP-36 on all collected samples including the following: (a) Atterberg limits (Liquid limit, Plastic Limit and shrinkage limits) (b) Natural moisture content (c) Wet and dry density of soil. (d) Soil partical size distribution. (e) Triaxial shear test. (f) Shrikage test. (g) Consolidation test. (h) Specific grevity test for sand and rock. (j) Crushing strength test. (k) Premeability test. (l) Chemical analysis of ground water sample. (m) Free soil index. (n) Chemical analysis of soil. (iii) Submission of report of soil investigation along with photograph in pentuplicate duly annotated with recommendation of SBC at different depth of foundation i.e.900mm, 1000mm, 1200mm, 1500mm, and 1700mm etc, depth of water table expansive soils type of foundation for security wall/retaining wall and details of soil profile bore logs. Nos of holes for SBC = 02 Nos 6 mtr depth of each i.e.total 2x6 = 12 RM

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil as directed by Engineer-in-Charge.

Roughening surface of old concrete floor/wall plaster by picking sweeping clean and washing down with water to remove dust etc

PCC type E-2 1:5:10(40mm graded crushed stone aggregate) in sub base and mass concrete complete all as specified.

Precast cement concrete interlocking tiles/paver block confirming to IS 15658-2006 machine pressed of approved shape and size in M-40 grade and 80mm thick with gray cement and pigment laid and bedded on 25mm thcik sand cushioning all as specified and directed by Engr-in-charge.

Removing excavated/surplus material not exceeding . 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.

25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate, as in sub base of floor complete all as specified and as directed by Engineer-in-charge.

Vitrified ceramic tiles 10mm thick light shade (square/ rectangular) polished, area of each tiles n.exc 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete including 15 mm thick screed bed in cement mortar 1:4, & roughening/cleaning to existing surfaces of old conc floor by picking sweeping clean and washing down with water to remove dirt/dust and brushing neat cement slurry with 3.00kg of cement per sqm complete all as specified.

Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.06 sqm but n exc 0.11 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed bed in cement mortar 1:4, complete all as specified and directed .

Glazed ceramic coloured tiles of size 450mmx350mm, thickness 7mm as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick mortar backing in cement mortar 1:4, incld dismantling floor hearth or wall tilling incld cement mortar bedding complete all as specified & directed.

Rendering 15 mm thick in cement and sand mortar 1:4 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge

Supply only integral water proofing compound.

GI frame work 605 x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soft it at approx x 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 centre to centre including 4 mm thick designer building board in grid fixed in position complete all as specified.

Preparation of new surfaces and apply one coat of acrylic emulsion exterior paint on wall/ceilings/facia complete all as specified and directed.

Excavation in trenches n.exc 1.5m in width and n.exc 1.5m in depth and getting out in any type of soil complete all as specified.

Cement concrete type D-2 1:4:8 (40mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified.

Brick work with Sub Class ‘B’ burnt bricks (Old size bricks) straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4 complete, all as specified.

Plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in drains or surface channels, finish even and smooth without using extra cement complete, all as specified .

Extra for forming fair finish drain or channel 30CM inner grith in cement concrete using extra cement complete all as specified.

Excavation over area n.exc 3.0m in depth and getting out in any type of soil complete all as specified.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete, all as specified.

Form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams, and similar work, vertical or to batter for rough finish surface of concrete complete, all as specified .

Formwork to for fair finished surfaces of walls retaining walls abutments parapets and staircase railing and similar work including attached pillasters buttresses etc vertical orto better all as specified.

Reinforced cement concrete M-25 (Design Mix) (using 20 mm graded aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc ; basement slabs, under- reamed piles and mass concrete, all as specified

Reinforced cement concrete M-25 (Design Mix) (using 20 mm graded aggregate) as in walls retaining walls basement walls and the like any thickness above top of footings including attached pilasters and buttresses, all as specified

TMT reinforcement bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified

TMT reinforcement bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified.

110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or floor for weep holes all as specified.

Plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregates as in bed blocks, coping, cills, plinth courses including weathering, slightly rounded or chamfered angles and throating and necessary form works, all as specified in clause 4.11.16.2(e) of MES Schedule Part-I

Pre-painted galvalume aluminum zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings, complete all as specified & directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in as in ridges, hips, valley gutters, drip and straight flashings, fixed with self tapping screws, complete all as specified & directed.

Rolled mild steel work in roof trusses (framed) trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W grade-E-250, including dismantling old mild steel angle, purlins complete all as specified & directed.

Taking down cement plaster on brick or stone surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specifed & directed.

10mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

Preparation of new plastered surfaces of wall over 10cm width or girth and applying two coats of oil bound distemper over a coat of primer, complete all as specified & directed.

Preparation of new plastered or concrete surfaces of wall and applying two coats of cement base paint over one coat of primer, complete all as specified & directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified & directed.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:6, complete all as specified & directed.

All as per Srl item no.38 above but except.

Machine cut kota stone slab flooring 18-22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade or the slab including rubbing and polishing complete including 20 mm thick in CM 1:4 screed for laying Kota Stone complete all as spd.

Ditto all as per item No. 40 but as in riser of steps ,skirting, dado and pillar including 10 mm thick in CM 1:4 rendring for Kota Stone complete all as spd.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified & directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as specified & directed.

Floor doors stoppers of aluminium alloy body and tenque anodisede with hard drawn steel spring fixed in floor 150mm long.

Pressed steel frames (factory made) of size 105mmx60mm made out of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, bottom of each frame to be welded with 02 Nos. 25x25x3mm angle iron projecting 10cm on either side and PCC 1:3:6 type C-0 using 12.5mm graded crushed stone aggregate for filling of hollow portion, complete all as specified & directed.

35mm thick factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled shutters (two panels) with lock rail and panels of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified & directed.

Preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified & directed.

Aluminium handle, cast type, anodised, 150mm long, complete all as specified & directed.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 200mm long, complete all as specified & directed.

250 mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified and directed.

Small fittings such as bracket of any type, latch and hinge blocks, shaped door and window stops and the like including all necessary labour, article not exc. 200 cucm each of 2nd class hard wood, complete all as specified & directed.

Mild steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, wire staples or beading etc, complete all as specified & directed.

3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exc. 0.5 Sqm in each pane, complete all as specified & directed.

Steel windows/ventilator (Box type) factory made with double shutter (wire gauged shutter & glass/glazed shutter, (wire cloth and glass panes shall be measured and paid separately) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long and 10mm square bar grills complete, two coats of synthetic enamel paint over one coat of red oxide primer including taking down old windows/ventilators all as specified & as shown on drg No. CEUZ/TD/1269/2008 Sh no 1/1 to 1/3 .

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of anti corrosive synthetic enameled paint over a coat of red oxide zinc chrome primer, complete all as specified & directed.

50mm thick PCC 1:3:6, nominal mix, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in bays not exc 2 Sqm each, surface finished even and fair without using extra cement including filling of 6mm thick joints with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 grade and three part of sand by weight, complete all as specified & directed.

Hard core of broken stone or boulder of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface.

PCC type C-2 1:3:6(40mm graded crushed stone aggregate) in sub base complete all as specified.

Mild steel rolled work as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other coving, running rails and guides) and hanging; also fastening and fixing complete, conforming to grade Fe 410-W (Gde-E-250) Quality-A, all as specified.

1.25mm thick mild steel, plain, black sheet in steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with riveted or welded complete all as specified.

Chequered cement concrete prelaminated coloured tiles of size 30cmx30cmx25cm thick factory made set jointed and pointed in neat cement slurry as in floors with grey cement anf pigementns laid over and incld 20mm thick screed bed in CM 1:4 finished even and fair to receive tiles over sub base of PCC 1:4:8 type D2 using 40mm graded curshed stone agg 75mm thick complete all as spd & directed.

Taking down carefully, copper / aluminium conductor unserviceable / perished point wiring (any type) for light/ fan/ light socket or power socket etc complete with fittings such as switches, sockets, ceiling roses, pendant holders, bracket holder, light fittings, regulators etc, including making good to disturbed surfaces of wall/floor etc, complete, all as specified & directed.

Taking down carefully unserviceable main switches, distribution boards of any type/size from their position including making good to disturbed surfaces of wall etc, complete all as specified & directed.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 1.5 Sqmm drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one light/fan point controlled by one way switch, complete all as specified & directed.

All as per Srl item No. 64 above but for one 3/5 pin 5 Amps socket outlet on same board .

All as per Srl item No. 64 here-in-before but for one 3/5 pin 5 Amps socket outlet on independent board.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 2.5 Sqmm drawn drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 2.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one 3/5 pin socket outlet 15 Amps independent, complete all as specified & directed.

Notes for Srl Item No. 64 to 68 (i) Unit rate includes for cutting chases whereever required and sinking for boxes, making good to walls / floors etc., complete, including white wash / colour wash as directed. (ii) Uniform coding of wiring i.e red / yellow / blue for phase black for neutral and green for earth is to be maintained.

Switch socket combination, two in one, 6 pin type, 5 & 15 Amp, flush type universal, complete all as specified & directed.

Ceiling rose surface type, bakelite 65mmx50mm, 3 terminals, complete all as specified & directed.

Switch piano flush type 5 Amps 240 Volt, single pole one way, complete all as specified & directed.

Switch socket combination, two in one, 5 pin type, 5 Amp, flush type universal, complete all as specified & directed.

Socket outlet two in one, 5 pin type, 5 Amp, flush type, complete all as specified & directed.

Fan regulator, deluxe socket type (electronic step type) for 1200/1400 sweep AC ceiling fan including taking down old unserviceable fan regulator, complete all as specified and directed.

Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified & directed.

LED lamp in white colour of 10 watt, retrofit type lamp complete all as specified & directed. Make : Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya/ Havells

Sheet metal enclosure, factory made for DBs, protection class IP-36, phosphatised powder coated, single door when MCB's to be used, single pole & neutral, 240 volts with 200 amps rated copper bus bar & neutral link earthing stud, 12 way, complete all as specified & directed.

MCB, single pole & neutral, 40 Amp, AC, 10 KA repturing capacity, 240 Volt, 'C' series, complete all as specified & directed.

MCB, single pole, 6 to 32 Amp, AC, 10 KA repturing capacity, 240 Volt, 'B' series, complete all as specified & directed.

Earthing of galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr depth below normal ground level) with top edge of earth not less than 1.5 mtr below normal ground level, surrounded on all sides by 150mm thick charcoal & common salt starting from ground below earth plate upto 150mm above GI plate in alternate layers connected to and including earth lead wire 4.0mm (8SWG) by means of steel bolts, nuts, check nuts and washers, test point made of GI strip 40x8mm, 10cm long PCC 1:2:4, type B-1 in pit with precast RCC 1:2:4 type B-1 in cover reinforced with XPM not less than 4 Kg per Sqm with 15mm bore GI light grade protection pipe, 20mm bore GI medium grade watering pipe with funnel including charcoal, dust, salt, all as shown in electrical plate No 3 of SSR Part-I (2009) complete with necessary earth work in any type of soil, removal to a distance not exceeding 50 mtr, including testing on completion, complete all as specified & directed. Note : (a) The cost of earth work, PCC pit of size shown in electrical plate No.3, funnel, watering pipe, wire mesh, charcoal, dust, common salt, 20mm bore medium grade watering pipe & 15mm bore light grade GI pipe as protection to earth lead wire etc shall be deemed included in the unit rate for earthing. (b) After completion, during testing, if the earth resistance equal or less 2 ohms is not obtained, earthing will be regenerated at no extra cost till the desired earth resistance is obtained.

New generation energy saving and environmental friendly long life LED street light of 20W made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening seperate driver compartment with IP65 protection and impact resistance of IK07 including GI bracket made of 40mm dia light grade GI tube 1.2 metre bend to shape with 02 nos FI clamp of 32x4mm with nuts, bots, washers, making connection with PVC copper conductor cable of appropriate size including taking down old unserviceable fittings, complete all as specified & directed. Make : Havells Cat Part No. ENDURA CITYLITEPLATSL 20W LED757SASYBOPC or equivalent of Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

Energy saving 10W LED bulk head luminaires, IP-65, oval shape, surface mounted with all other accessories prewired and making connections with copper flexible twisted twin cord of appropriate gauge and length,230v, 50Hz including taking down old unserviceable fitting including taking down old unserviceable fittings, complete all as specified & directed. Make. Havells, Cat Part No.RUGBYNEONFT10W LED760SSYMBOPC or equivalent in Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

Surface & wall mounted, LED tube light fitting, 20W, glare free, smooth light distribution, 230v, box type, epoxy powder coated CRCA sheet housing with reflector cover channel, aesthetic looking end cap and HPF LED driver with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size, complete all as specified & directed. Make. Havells, Cat Part No. ENDURALINEARNEOBS 22WLED865SPCWH or equivalent in Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

Taking down to ceiling fans and hanging the same and connecting up including provision of cable from ceiling rose or connector to fan as directed by Engineer-in-Charge.

Preparation of old surfaces of ceiling fans by scraping out old existing paint with the help of emery paper/wire brush including filling the cavities and painting with two coats of white synthetic enamelled paint over a coat of red oxide primer with the help of spray machine including re-writing MES No SL No with black synthetic paint in Capital letter for 1200 mm sweep ceiling fan, complete all as specified.

Supply and fixing/hanging fans ceiling 230V 1200mm sweep BEE 5 star rated double ball bearing complete accessories like set of blade upper/lower conpoy down rod rubber reel safety pin condenser etc with fan in white colour only. Make : Havells Model No ES NEO, Crompton : Model No HP Plus 5 Star, Bajaj: Model No Kassel star, Orient : Model No Energy Star ceiling Fan or equivalent as per list of make.

Supply and fixing/hanging fans ceiling 230V 1400mm sweep BEE 5 star rated double ball bearing complete accessories like set of blade upper/lower conpoy down rod rubber reel safety pin condenser etc with fan in white colour only. Make : Havells Model No XP 390, Orient : Model No New Hurricane ceiling fans 1400mm or equivalent as per list of make.

Supply and fixing PVC twin core copper conductor twisted wire of size 23/0.0076 all as specified.

M/s Sekinder Paul Sharma

JR CONSTRSTRUCTION CO.

M/s Joginder Lal Malhotra