ADDN/ALTN TO BLDG NO P-138(CRANE SHED) AND ADDN / ALTN TO STORE ROOM IN CG HOUSE AT COAST GUARD UNDER GE HADDO AND REPLACEMENT FTL FITTINGS WITH RECESSES LED LIGHT FITTINGS AT REGIONAL IT CENTRE AT SHIP SUPPORT COMPLEX UNDER GE HADDO, PORT BLAIR

Amount

Demolition of cement concrete of any description and in any position not otherwise specifically provided for etc complete all as specified and as directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for etc complete all as specified and as directed.

Demolition of Precast cement concrete block walling built in CM or Cement lime Mortar complete etc all as specified and as directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness including similar pattern roof coverings.

Dismantling structural steel work complete all as specified.

Taking down Aluminium Windows, or door frames with shutters without taking off shutters from frames exe 1.5 Sqm and n.exc 4 Sqm each complete all as specified and as directed.

M&L For Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation etc not exceeding 10 sqm on plan and n.exc 1.5 m in depth and getting out in hard / dense soil etc all as specified and as directed.

M&L for Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm hard dense soil complete all as specified and as directed.

M&L for Removing excavated material n.exc, 50 m and depositing where directed at a level n.exc, 1.5m above the starting point complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete etc all as specified and as directed.

M&L for form work to sides of concrete foundations, footings, raft and raft beams, sides and soffits of foundatrion and plinth beams and similar work for rough flat surfaces complete all as specified and as directed.

M&L for form work to sides of columns and similar works for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for form work to lintel beams, roof beams, chajjas and similar works for rough finished flat surfaces of concrete complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including crancking, bending spirally hooping for columns, hooking ends and binding with mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed.

Mild steel TMT bars 5mm dia and up to 10mm dia as in stirrups, cut to length, bent to shape requiried, including brancking, bending spirally hooping for columns, hooking ends and binding with mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed.

M&L for Reinforced cement concrete Type B1 1:2:4 using 20mm graded aggregate as in foundations/footings, plinth beams, bases for column, etc., complete all as specified and as directed.

M&L for Reinforced cement concrete Type B1 1:2:4 using 20mm graded stone aggregates as in columns, pillers etc complete all as specified and directed

M&L for Reinforced cement concrete Type B1 1:2:4 using 20mm graded stone aggregates as in lintel beams, roof beams, chajjas etc complete all as specified and directed

M&L Precast cement concrete block masonry exc 10cm in width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:6) etc all as specified and as directed.

M&L for Rendering 10mm thick in CM (1:6) on fair faces of concrete/PCC block surfaces of walls finished even and smooth without using extra cement etc all as specified and as directed.

M&L for Rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement etc all as specified and as directed.

Preparation of newly plastered Internal wall surface and applying two coats of distemper oil emulsion over a coat of primer over the coat of 3mm thick wall care putty etc complete all as specified and as directed.

M&L for preparation of new plastered surfaces and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed.

M&L for Hardcore of gauge n exc. 63 mm of broken stone boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L for PCC type D-2, 1:4:8 (using 40mm graded aggregate) 75mm thick as in sub floor, sub base floor and pavings etc complete all as specified and as directed

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tiles exc 0.18 sqm but not exc 0.38 Sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed of CM (1:4) bedding complete all as specified

All as per item No 26 above but as in skirting / dados etc. including backing coat 10mm thick in cement mortar 1:3, complete all as specified.

S&F for Anodoised aluminium powder coated snap grid frame work for ceiling 605mm x 605mm using aluminium anodised sections aluminium sections main tee 36.5X25X1.4mm, cross 23.5X26.4X1.4mm, angle 25X25x1.4mm including cutting, drilling jointing etc complete including 4mm dia of GI hangers wire suspenders fixed with adjustable connectors and providing 6mm thick E-boards (Classic) 605mm x 605mm size Specified by Engr-in-charge and making good etc complete all as specified and as directed.

S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for frames of doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

M&L for 12mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to aluminium frame work or doors etc all as specified and as directed.

Supply only plain sheet glass 5.5 mm thick ordinary quality and glazing with aluminum glazing clip in aluminum window shutter not exc 0.5 Sqm in each pane.

Supply only Aluminium alloy wire cloth 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples all as specified and directed.

S&F 100 mm Butt hinges type B-21 extruded aluminium alloy with galvanized mild steel hinge pin anodized complete all as specified and as directed.

S&F 150mm long extruded aluminum alloy handle fabricated type anodized etc complete all as specified and as directed.

S&F 150mm long Aluminum anodized barrel tower bolt of extruded section etc complete all as specified and as directed.

S&F 300mm long Aluminum alloy anodized sliding door bolt with hasp and staple (bolt type) and fixing bolts and sliding bolts of extruded section or cast aluminum alloy etc complete all as specified and as directed.

S&F 150mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor etc complete all as specified and as directed.

S&F for pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering, ridge, eves gutters etc fixed with self tapping screws as specified.

S&F for Mild Steel works in Roof trusses (framed), purlins, bracings etc, fastening and heavy brackets framing (using beam, tee, angle, channel or flats section) including distance pieces, cleat etc conforming to Fe-410 (Gde-E250) quality -A complete all as specified and as directed.

M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for Aluminium wind tie of any size fixed with self tapping screws of size 50/75mm with integral EPDM washer in roof covering etc fixed with self tapping screws as specified.

M&L for PCC (1:4:8) type D-2 (using 40mm graded aggregates) as in sub base 100mm thick complete all as specified and as directed.

S&F for glossy finished chequered cement concrete tiles 30cmx30cmx25mm thick set jointed with grey cement and pigment and pointed in neat cement slurry over and including 20 mm thick screed bed in CM(1:6) etc all as specified and as directed.

M&L for preparation of newly plastered External wall surfaces and applying two coats of cement based paint over a coat of primer etc complete all as specified and as directed.

M&L for 40mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) finished even and smooth using extra cement etc complete all as specified and as directed.

M&L for glass dividing strips 3 mm thick & 28 mm width inserted in position in floors complete all as specified and as directed

S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket and necessary Builder hardwares required for functioning etc, with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

M&L for 18mm thick Prelaminated HDF particle board, exterior grade prelaminated both sides with decorative choice laminations fixed with screws to aluminium frame work etc all as specified and as dierected.

S&F Steel Rolling shutters of 1.25mm thick laths, gear operated type with bevel gear box and crank handle and without ball bearings and as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated etc complete all as specified and as directed.

Supply only Ball bearing for rolling shutters etc complete all as specified and as directed

M&L for pre cast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in cover slabs, shelves and similar articles set in cm 1:6 finished even and smooth with necessary form works etc all as specified and directed

Excavating over areas, n exc 1.5 m deep and getting out and getting out in hard/dense soil etc all as specified and directed

M&L Cement concrete work in pavement/hard-standing of flexural strength 40kg/cm2 in field using 400 kg of cement per cubic metre complete all as specified and as directed

M&L for forming Expansion joints of 150mm deep x 12mm wide in concrete slab filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ etc complete all as specified and as directed

M&L for forming Construction joints of 30mm deep x 10mm wide in concrete slab filled with sealing compound, Grade ‘A’ etc complete all as specified and as directed

Taking down copper/aluminium point wiring(light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials and making good disturbed surfaces of walls, floors, etc.

Taking down fuse Unit/DBs 415 Volt/230 Volt complete all as directed.

Taking down old aluminium sub main wiring of any size complete all as directed.

Taking down existing light fittings of any type any capacity complete all as directed.

M & L for point wiring two single core 1.5 sqmm size PVC insulated, unsheathed FRLS multistranded copper conductor cable and one single core 1.5 sqmm size green colour PVC insulated FRLS multistranded copper conductor cable as earth continuity conductor, 1100 volt grade (with proper colour coding Red/Blue/Yellow for phase , black for neutral and green for earth) complete drawn through and including PVC casing and caping not less than 25mm width with all fittings, surface on wall/roof/floor including sunk pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover for mounting switches/sockets/ regulators etc. complete as specified for one 15 Amps socket point controlled by one 15Amps switch.

Description same as per Srl item No 60 above but One light/fan point controlled by one switch 5 Amps one way.

Description same as per Srl item No 60 above but, point wiring for 3 pin switch socket outlet , 6 Amps on independent board

Description same as per Srl item No 60 above but One point wiring for 3 pin switch socket outlet, controlled by one switch 5 Amps on same board.

M&L for Point wiring complete with 4.0 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including PVC casing and caping not less than 25mm width with all fittings, surface on walls/ceilings etc., including provision of PVC insulated 4.0 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk pressed steel terminal boxes with plastic laminated sheet cover of 3mm thick on top for housing the switches, socket outlet etc, all as specified and as directed for ONE 16A SOCKET OUTLET point controlled by one, one way 16 Amps switch on independent board.

M & L point wiring complete with 1100 volts grade, 1.5 sq.mm (nominal area), single core, FRLS PVC insulated ,unsheathed, multi stranded copper conductor cable drawn through and including medium grade, rigid , non-metallic PVC concealed/ surface as possible conduit of size not less than 20 mm dia, with all necessary fittings, concealed in walls /roof/ floor duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire and connecting to common earth duly including suitable size of factory made fabricated sunk pressed MS sheet modular terminal box, flush mounting in the wall for mounting switches/switch socket combinations/ fan regulators etc., covered with suitable size of modular cover plates complete in making good the existing surface with existing colour coding as required at site complete all as specified for the following :- Make : Polycab/Havells /Finolex/ Gloster/Anchor

Description same as per Srl item No 62 above but One light/fan point controlled by one switch 6 Amps one way.

Description same as per Srl item No 62 above but, point wiring for 3 pin switch socket outlet , 6 Amps on independent board

M&L for Point wiring complete with 4 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC concealed / surface as possible of suitable size (not less than 25mm) and accessories fixed in walls/ceilings etc., including provision of PVC insulated 4 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE 16A SOCKET OUTLET point controlled by one, one way 16 Amps modular switch on independent board.

S&F Switch piano, flush type, single pole one way 6 amps all as directed. Make: Anchor/Cona/Legrand.

S&F Switch piano, flush type, single pole one way 16 amps all as directed. Make: Anchor/Cona/Legrand

S&F socket outlet 2 in 1, 3 pin 6 amp, flush type, universal all as directed. Make: Anchor/Cona/Legrand.

S&F socket outlet 2 in 1, 3 pin 16 amp, flush type, universal all as directed. Make: Anchor/Cona/Legrand.

S&F Ceiling rose, surface polycarbonate body 65x50mm, two to three terminal all as directed. Make: Anchor/Cona/Legrand.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd 120 W complete all as specified.Make : Anchor/Cona//Legrand

S & F Sub main wiring with PVC insulated cable 2 single core 4 sq mm 1100 V grade with stranded copper conductor cable using proper colour coding Phase Red/Yellow/Blue, Neutral- black and earth- green in and incl rigid PVC conduit concealed in wall/surface (ISI marked) incl all specials like joint elbow, Tee ,junction , bend etc and provision of PVC insulated copper conductor single core 4.0 sq mm for earth continuity all as directed. Make:Gloster /Havells /Anchor /Polycab /Finolex

S & F Sub main wiring with PVC insulated cable 4 run single of 4 sq mm 1100 V grade with stranded copper conductor cable using proper colour coding Phase Red/Yellow/Blue, Neutral- black and earth- green in and incl rigid PVC conduit concealed in wall (ISI marked) incl all specials like joint elbow, Tee ,junction , bend etc and provision of PVC insulated copper conductor single core 4.0 sq mm for earth continuity all as directed. Make of wire : Polycab/Gloster /Anchor/ Havells/ Finolex and Make of PVC conduit : Modi/ Precision/Supreme/ Finolex/ Polycab NOTE : Five runs of 4 sqmm cable alongwith PVC conduit shall be measured as one unit .

S & F DB VTPN sheet metal enclosure double door suitable for incoming upto MCCB 100 Amps/125 Amps & outgoing MCB TP / SP (IP-43) Protection Triple pole and neutral 415 V 4 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete all as specified and directed. Make : C&S /Indo Asian /Havells/L&T

S & F single pole and neutral sheet steel powder coated Distribution board IP -43 protection with door earthing for MCBs fitted with 200 Amps rated bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 8 ways,including taking down old unserv DB of any type /rating and making good to the distrubed surface /walls. Make: C & S / Indo Asian/Havells/L&T/Legrad

S & F single pole and neutral sheet steel powder coated Distribution board IP -43 protection with door earthing for MCBs fitted with 200 Amps rated bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 6 ways,including taking down old unserv DB of any type /rating and making good to the distrubed surface /walls. Make: C & S / Indo Asian /Havells/ L&T/Legrand

Supply and Fixing 4 pole MCCB 100 Amp, 50 Hz, 415 V with rupturing capacity 25 KA complete all as specified and directed Make :C&S/ Indo Asian /Havells/L&T

S & F MCB TPN ,63 amps, 10 KA , 230 volts , all as directed. Make: Indo Asian/Havells/L&T/Legrad

Supplying & fixing MCB SPN 40 Amps (`C’ series) having current rating 10 KA complete all as specified and directed Make : C & S/ Indo Asian/Havells/L&T

Supplying & fixing MCB single pole, 6 to 32 Amps (`C’ series) having current rating 10 KA complete all as specified and directed Make : Indo Asian/Havells/L&T

S & F for switch modular type, 6 Amps 1 module, 230 volts AC circuit complete all as specified and directed. Make : Roma (Anchor)/Legrand/ Havells

S & F Switch piano modular type , flush type, single pole one way 16 amps all as directed. Make : Roma (Anchor)/Legrand/ Havells

S & F for socket outlet modular type 1 way 6 Amps, 3 pin, flush type 230 volts AC circuit complete all as specified and directed. Make : Roma (Anchor)/Legrand/ Havells

S & F Socket outlet 2 in 1 modular type, 3 pin, 6 and 16, flush type, universal all as directed. Make : Roma (Anchor)/Legrand/ Havells

S&F 30 Watts LED light, recess mounting luminaire with glare free uniform illumination having longer life and less maintenance, size 600mm x 600mm, 25000 burning hours including all accessories and fixing arrangements for fixing the light fitting complete all as specified and as directed. MAKE: PHILIPS Cat part No. RC380B LED30S-6500 G5 L60W60 PSU OD SG or CG Cat Part No : LCTLRNE-30-F0-CDL equivalent make of Havells/Luker

S & F BLDC 5 star rated ceiling fan metallic body ISI marked 1200 mm sweep, 220V Ac, 50 Hz complete with all accessories. Make: CG Model No : ENERGION Riviera or equvalent make of Havells/Orient/ Usha /Bajaj.

Supply, fixing and testing on wall , Industrial type ,heavy duty Air circular fan 600 mm sweeep 1400 RPM, single phase, 220 volt, single phase, 50 Hz incl all fixing arrangement complete all as specified and directed Make: CG Model No : ACVORTEX24WM /Havells /Usha/Orient

Supply and fixing heavy duty Exhast fan of 300 mm sweep, 1400 RPM, 220 volts, 50 Hz , ISI Marked, AC supply, complete all as directed. Make: Havells Model No : FHEHDSPDB120 /Usha/Orient/ CG

Supply and fixing LED Flood light of capacity 150 watts pressure die cast aluminium housing with toughened glass and high power LEDs and secondary lenses with IP 65 protection system efficacy > 110 LPW 10 KV SPD incl all fitting arrnagement complete all as directed. Make: CG Model No CFS-501-150-57-60D-SL-GL-NGG /Usha/Orient/ Havells

Supply & fix AC starter switch of capacity 25 Amps working on 240 volts AC supply suitble for air conditioner complete all as specified and directed. Make : Crabtree Model No : ACTO252504

Supply,laying,testing and commissioning of LT XLPE insulated, armoured heavy duty electric aluminium conductor cable 1100 Volts grade of cross section 16 Sqmm 4 core (laid in trenches/on floor/Roof/wall in proper saddling all as specified and directed. Make Polycab/Gloster/Anchor/ Havells/ Finolex

Supply and laying in trenches or in cable ducts or clamping on wall DWC HDPE pipe of size 50 mm(OD) x 38mm (ID) along with connected accessories like couplers.bends,end caps etc. for HT cable protection all as specified and directed.Make:Rex Poly Extrusion Ltd/Tirupati Plastomatics Pvt Ltd.

Earthing complete with galvanised earth plate electrode 60 cm x 60cmx 6.15 mm thick, buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the earth plate not less than 1.5m below ground level , connected to GI earth wire 4 MM Dia as earthling lead by means bolts and nuts check nuts and washers of galvanized iron and connected to main switch board including watering arrangement with PCC chamber , MS funnel with wire mesh,. CI cover with frame etc including necessary excavation in any type of strata , returning, filling removal of soil outside MD land ,filling of charcoal and salt complete all as shown in electrical plate No. 3 of MES Sch Part I , connected to Earthing test point all as specified and directed on testing on completion.

Supply and fixing of Decorative ultra slim linear LED lighting fixture of 18 Watt recess mounted 220V , 50Hz with Aluminium housing ,environmental friendly energy efficient fitting recess mounted round/square in shape (Warm white/ white colour as per requirement of site complete) of light as required at site) complete all as specified and directed. Make - Philips Cat Part No : Dura Slim or equivalent make in CG//Havells. NOTE: The rate quoted deemed to include for any alterations required to existing false ceiling as per site condition for fixing light fitting .

M & L Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface with or without reinforcement all as specified and as directed by Engineer-in- Charge

M/s Ramesh Lal

SKV Engineering

Bismi Builders & Enterprises

MAJUMDAR FURNITURE

A PALANI

SHUBHAM SHANKAR GAIKWAD

CHANDER SEKER ENTERPRISE

Reliance Sales Agency