PROVN OF SOAKAGE WELL SEPTIC TANK NEAR BLDG P7 P8 P35 6 GD SPL RPRS TO JCOS MD ACCN P1 1 TO 4 AT BHAGAT ENCLAVE 7 GD CONSTN OF UG SUMP SERVICE STN AND B VEH RAMP WASHING VEHS AT 7 ARMD WKSP AND CERTAIN SANCTN WKS UNDER AGE B R II BABINA

Amount

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tennsile strength of 550 Mpa as in roof covering/cladding to wall , fixed with self taping screws as specified all as directed.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheetingin 0.50mm ridgs, thick of an colour having tennsile strength of 550 Mpa as in roof covering/cladding to wall , fixed with self taping screws as specified all as directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or inducton butt welded tubes confforming to IS.1161-1979 grade St-240.

M & L preparation of newly untreated surface of steel and applying two coat synthetic enamal paint over one coat red oxide of any description, over 10cm inwidth or girth, not otherwise described.

Excavation over areas not exceeding 1.5M depth and getting out in any type of soil.

Excavation in post holes ( or similar holes) each n exc 0.5 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc. 25cm each.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5M in depth for foundation etc and getting out in any type of soil complete all as specified and as directed.

Returning filling Soft/loose soil including spreading, levelling, watering and well ramming in layers n exc. 25cm

Removing excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point.

M&L PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete as sub base of floor complete all as specified and as directed.

M&L PCC 1:5:10 type E-2 (using 40 mm graded stone aggregate) as in sub base of floor complete all as specified and as directed.

M & L cement concrete 1:2:4 type B-1, (using 20mm graded stone aggregate) as in floors finished fair and even without using extra cement complete all as specified and as directed.

M & L Cement concrete 25mm thick type B0, 1:2:4 (12.5mm graded aggregate) in floor all as specified as directed.

Forming construction ( Dummy ) joints 65x10mm wide , filled with sealing compound Grade 'A'. complete all as specified and as directed.

Form work to sides of concrete foundation,footing, base of columns, plinth beams finished fair finished surfaces of concrete flat all as specified

Form work to sides of square columns etc fair finished surfaces of flate concrete all as specified

Form work to sides and soffits of roof beams, lintels lever shelves incl supports over hang etc fair finished surfaces of concrete flat all as specified

Form work to soffits of suspended slabs such as roof slabs, floor slabs landing and similar work n exc 200 mm thick (horizontal sloping )

M&L TMT bars 10 mm dia and over cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality confirming including stirrups all as specified

M&L TMT bars 6 - 8 mm dia cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality confirming including stirrups all as specified

M&L providing reinforced cement concrete Type B1, 1:2:4 (using 20 mm graded stone aggregate) as in foundation, footing,plinth beam all as specified.

M&L providing reinforced cement concrete Type B1, 1:2:4 (using 20 mm graded stone aggregate) as in columns all as specified.

M&L providing reinforced cement concrete Type B1, 1:2:4 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span all as specified.

M&L reinforcement cement concrete type B-1 (1:2:4) (using 20 mm graded stone aggregate) in slab supported on walls beams ,roofs landings, balconies, canopies,deck slabs and in shelves and the like

M&L reinforced cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) with WPC as in retaining walls, basement walls, ballast walls and the like any thickness above top of footings including attached pilaster and buttresses under reamed piles.

M&L precast re-inforced Cement Concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in cover slabs for man holes etc set in cement mortar 1:6 including necessary form work complete all as specified and directed

M&L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes 150mm internal dia including packing under haunching against the sides of pipes after laid and testing complete.

M&L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes 200 mm internal dia including packing under haunching against the sides of pipes after laid and testing complete.

M&L salt glazed stone ware drain pipe 150 mm internal dia laid in trenches and jointed.

M&L salt glazed stone ware drain pipe 200 mm internal dia laid in trenches and jointed.

M & L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cm(1:6)

M & L Brickwork with fly ash bricks in one brick thick honey-comb walling built in CM (1:3) all as directed.

M&L for rendering 15mm thick in cement mortar (1:6) on brick/concrete surfaces and finished even and fair without using extra cement on wall all as specified and directed.

M&L rendering 5 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 with WPC, surfaces finished even & smooth using extra cement.

M&L Preparation of newly plastered surfaces of walls , using white putty and applying two coats of cement base paint over a coat of alkali resistant primer complete.

M&L Preparation of new surfaces plastered of wall using wall putty and three coat of white wash on wall.

M & L hardcore of gauge n exc. 63 mm broken stone deposited, spread, rammed and levelled to a true surface in layers n exc. 15cm thick all as specified.

M & L surface excavation n . exc 30cm deep and averaging 15cm deep and getting out soft and loose soil all as directed.

M & L Machine pressed precast concret interlocking paver block any shape and size of 80mm thickness with grey cement and pigment over 50mm sand cusion all as specified by engineer-in-charge.

S & F 15mm bore galvanised iron tubing medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete the rate also included for cutting through walls floors etc all as specified and as directed.

S & F 20 mm bore galvanised iron tubing medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete the rate also included for cutting through walls floors etc all as specified and as directed.

S&F kitchen sink with drainage board made out of 1mm thick stainless steel with plugs washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe over all size 915mmx460mm & bowl size 410mm x330mmx160mm complete all as directed by the Engineer-in-Charge.

S&F 15 mm bore bib taps long body chromium plated fancy type, cast copper alloy with crutch or butter fly handle screwed down screwed for iron pipe or for unions and fixed complete.

S&F 32mm dia flexible waste pipe for kitchen sink complete all as specified and as directed.

Dismantling of existing water tanks of steel /PVC/RCC of capacity exceeding 250 liters but not exceeding 500 litres complete all as specified and as directed.

S & F 500 litre capacity of rotational moulded polyethylene water storage tank multilayered construction, ISI marked of make specified (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia GI pipe medium grade wash out pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings complete all as specified in SSR Part-I complete all as specified and as directed.

S&F 20 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. .(Minimum weight 15mm-142gms/ 20mm-210 gms./25mm-455gms etc complete.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with waste to remove dust, etc.

M&L Machine cut Kota stone slab flooring 18 to 20 mm (+ 2mm) thick laid over and including 20 mm thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and nosing complete all as specified and directed.

M&L Machine cut Kota stone slab flooring 18 to 20 mm (+ 2mm) thick in as in skirting/Dado over 10mm thick rendering in cement mortar 1:4 and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Dismantling of wall and ceiling boards (fibere, pulp, insulation boards/slabs/ blankets), any thickness. Including cover fillets

S & F for aluminium anodised snap grid of size 605mm x 605mm size to support the boars, tiles with aluminium tee section 35mm x 25mm x 1.40mm, cross tee 23.50mm x 23.50mm x 1.40mm and aluminium angle 25mm x 25mm x 1.40mm as on edge/sides including proper hanging arrangement with 4mm dia nodized galvnised iron wire and adjuster incouding 4mm tick Everest Non Asbestos fiber cement designer board (E-Board classic) size 60cm x 60cm fixed on ceiling on staples of snap grid and including making good the distrubed wall portion with CM 1:3 or with PCC, 1:2:4 type B1 ( using 20mm graded stone aggregates ) as required complete all as secified and directed.

M & L for complete removal of existing treament on ceiling and applying three coat of white wash all as specified and as directed.

Complete removal of existing treatment preparing using white putty and applying two coats of OBD over a coat of primer. on wall using one coat of primer all as directed.

Complete removal of existing treatment on wall using one coat of primer and white putty two coat of cement base paint on wall surfaces.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) not exe 1.5 Sqm each etc complete.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) but exc 1.5 Sqm and n exc 4 sqm each etc complete.

Framed work such as in doors or gate or angle or other section with gusset plates rails braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hook and hinges (exclusive steel sheeting or other covering running rails and guids ) and hanging also fastening and fixing complete all as specified and as directed Fe-410(Gde E-250).

S&F 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides etc complete.

S & F factory made 35 mm thick IInd class HW glazed & skeleton shutters open rebated and prepared to receive glass gauge etc. (without sash bars) edges of framing plain chamfered or rounded fitted with cut & mitered beads for security glass/gauge etc. size of members of shutter as specified in SSR Pt I sec 8 Cl 8.20 (a), divided into squares with plain chamfered rounded, mitered and rebated sash bars etc complete.

S & F butt hinges medium weight cold rolled, mild steel and fixed 100 mm size etc complete.

S&F aluminium anodised barrel tower bolts of extruded section and fixed fixed 150 mm long etc complete.

S&F aluminum handles cast type anodized 150 mm size etc complete.

S&F mild steel, 300 mm ordinary door spring including roller and roller plate etc complete.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy.

M&L two coat synthetic enamel paint over one coat of pink primer on new wooden surface of any description not otherwise described over 10 cm width or girth etc complete.

S & F Steel windows with side hung shutterss including box type hinges with steel handle, and steeel peg stay, complete with glazing bars, dovetailed or welded.

S & F Steel windows with side hung shutterss including box type hinges with steel handle, and steeel peg stay, complete without glazing bars, dovetailed or welded.

S & F Framed work such as grills, gratings, etc. with ends of bars shouldered and riveted or forged into spikes, framed guard bars , barred iron doors, ladders ,framed balusters, walk ways, railinngs, framework of water tanks and similar work conforming to Fe290 Gde -E-165.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and avg width of aperture 1.18 mm fixed with tinned tacks or galvanized wire staples etc complete.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc.0.50Sqm each pane complete all as specired and directed

S&F 19/20 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice laminations and other side balancing white lamination fixed with screws to timber frame work etc complete.

S&F Hasp & staple safety type aluminium anodized with mild steel hing pin incl bolt to hing plate and fixed with screws 100mm size etc complete.

S&F Continuous (piano) hinges, mild steel bright finish electrogalvanised 20mm width of flap etc complete.

M&L for coloured joint free non skid ceramic tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor, over and including 15mm thick screed bed or bedding layer in cementy mortar 1:6, over 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) etc complete.

M&L for coloured joint free ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in skirting/dado etc. set and jointed in neat cement slurry and pointed in colour cement to match to floor, over and incl 10mm thick rendering on wall surfaces in cement mortar 1:4 ,complete all as specified and as directed.

M&L for glazed coloured ceramic tiles 300 x 600 x 10 mm thick for work on vertical surface such as skirting, dado, set & jointed in cement slurry and pointed in white or coloured cement to match the existing wall surfaces, over and including 10mm thick rendering in cement mortar 1:4 etc complete.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone including cutting and polishing types over 15 mm thick in CM(1:6) etc complete.

S & F Cast Iron Soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to wall 100 mm bore including fixing of necessary clamp and taking down old PVC/CI/Concrete pipe.

S & F Cast Iron Soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to wall 75 mm bore including taking down old PVC/CI/Concrete pipe.

S&F Cast Iron bends any radius 100mm bore.

S&F Cast Iron bends any radius 75mm bore.

S&F Cast Iron 'T' any radius 100mm bore.

S&F Cast Iron 'T' any radius 75mm bore.

S&F Cast Iron cowl any radius 100mm bore.

M & L for concealed point wiring complete with PVC insulated and unsheathed flame retardant los smoke low smoke ( FRLS ) cable of 1.5 sqmm (nominal area) with stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit not less than 19 mm dia, clip, with MS terminal boxes (not less than 1.0 mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including common earth dolly with 3 mm thick plastic laminated sheet top cover of approved make and colour including 1.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete including cutting necessary chases on wall / ceiling surfaces for drawing of conduit & cables as required and making good disturbed surfaces of walls with CM 1:3:6 and matching with the existing surfaces including colour washing all as specified and as directed for the following :- (a) One light point controlled by one switch

(b) One 3/5 pin 5 Amp socket outlet point controlled by one switch on independent board.

(c) One 3/5 pin 5 Amp socket outlet point controlled by one switch on same board.

Description all as per item No 86 above but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed flame retardant low smoke ( FRLS ) cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with 1.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete all as specified and as directed.

S&F switch piano flush button type 5 Amp single pole one way complete all as specified and as directed.

S&F socket outlet 2in1, 3 pin, 5 Amp flush type complete all as specified and as directed.

S&F switch piano flush button type 15 Amp single pole one way complete all as specified and as directed.

S&F socket outlet 2in1, 3 pin, 5 Amp and 15 Amp flush type complete all as specified and as directed.

S & F Lamp holder,PVC/Urea type with back plate suitable for batten fittings complete all as specified as directed

S&F ceiling rose,surface bakelite 63 x50mm three terminals complete all as specified and as directed.

S&F sheet metal enclosure double door suitable for distribution boards when MCBs to be used having 100Amp rated bus bar SPN, 8 ways 240 V complete all as specified and as directed.

S&F MCB SPN 6 to 40 Amps 240 V,10KA, 'C' Curve series,complete all as specified and as directed with copper lugs

S&F MCB single pole 6 to 40 Amps 240 V,10KA, 'B' series,complete all as specified and as directed with copper lugs

Supply and fixing in repair 18/20 W LED 6000k Decorative ultra slim linear LED fitting fixture with extruded polycarbonate ,environmental friendly ,energy efficentinterated driver and 20 watts lamp fitted including wiring upto and terminal into existing ceiling rose complete all as specified and directed by Engr-in- Charge. Make havells cat part No -ENDURALINEARNEOBS20WLED865SPCWH 020 or equivelent in philips/bajaj /CG.

S&F LED security/ street light fitting 1 X24 W LED 6000K energy saving & environmental freindly long life versatile pressure die cast aluminium IP 66 roadway luminaire with high power LEDs as light source and electronic driver suitable for pole dia 35 mm including 35mm dia light grade tube bracket, bend to shape 1.80 mtr length with two nos clamp of size 50mm x 6 mm with nut, bolts, washers etc including connection with 1.5 sqmm two single core PVC insulated and PVC sheathed cable stranded Copper conductor upto ceiling rose and fixing on walls/pole complete as specified and as directed. Make: – Havells Cat No LHETAXU7PA6S025 OR equivalent of Philips/Bajaj.

S & F LED bulb1x9 watt having PF not less than 0.90 suitable for holder fittings complete all as specified and directed. Make : Philips/Surya/Bajaj/Crompton greaves.

Supply ,laying and testing cable XLPE insulated screened PVC bedded ,galvanised steel strip armoured ,electric power cable (heavy duty ) 1100 volt grade with stranded aluminium conductor of size 10 sqmm 4 core complete all as specified and directed.

supply laying dry clean sand free from sharp materials, unscreened filling in trenches around under ground cables for cushioning complete all as specified and directed.

M&L for brick protection covers over cables of sub class B bricks old size , laid dry over cables (length of bricks shall be laid across the length of the cable complete all as specified and directed

M&L pipe galvanised iron, light grade ISI marked, complete with fittings laid inj trenches/ fixed with poles etc as protection to cables complete as ditrected by Engineer in Charge for the size 32 mm dia

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick weithing not less than 17.5 Kg buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PT 1, 2010 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs) complete all as specified & testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

M & L for surface type condute wiring point wiring complete with PVC insulated and unsheathed flame retardant low smoke ( FRLS ) cable of 1.5 sqmm (nominal area) with stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit not less than 20 mm dia, clip, with MS terminal boxes (not less than 1.0 mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including common earth dolly with 3 mm thick plastic laminated sheet top cover of approved make and colour including 1.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete including cutting necessary chases on wall / ceiling surfaces for drawing of conduit & cables as required and making good disturbed surfaces of walls with CM 1:3:6 and matching with the existing surfaces including colour washing all as specified and as directed for the following :- (a) One light point controlled by one switch

(b) One 3/5 pin 5 Amp socket outlet point controlled by one switch on independent board.

(c) One 3/5 pin 5 Amp socket outlet point controlled by one switch on same board.

Supply and Fixing High efficacy 2x2 recess LED flat panel light with high brightness LED for glare-free homogenous illumination recess mounted powder coated white CRCA full glow deep drawn panelcomplete with all accessories pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Havells-Cat part No (PLUTO NEO Panel 2x2 NLHEWEBP7IN1W034 of 34W LED 6000K./CG /C&S or bajaj or equilant

Supply & lay galvanised iron 50mm bore pipe medium grade with all fittings laid trenches/walls complete and all as specified.

Supply & lay galvanised iron 40mm bore pipe medium grade with all fittings laid trenches/walls complete and all as specified.

Supply & lay galvanised iron 25mm bore pipe medium grade with all fittings laid trenches/walls complete and all as specified.

Supply & lay galvanised iron 20mm bore pipe medium grade with all fittings laid trenches/walls complete and all as specified.

Supply & lay galvanised iron 15mm bore pipe medium grade with all fittings laid trenches/walls complete and all as specified.

Supply &Fix gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed to pipe of 50mm dia.

Supply &Fix gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed to pipe of 25mm dia.

Supply & Fix gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe and fixed to pipe of 20mm dia.

Supply & Fix gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe and fixed to pipe of 15mm dia.

M & L for Cutting of existing 100mm ddia GI/CI pipe in position at 2 places and threading inserting TEE 100 x 100 x 25mm including all fitting such as union, socket, nipple etc and making leakage proof joints using rubber gasket and other packing materuial etccomplete all as specified and directed.

M&L Construction of Valve Pit of size 45x45x60cm (internal dimensions), stone masonry construction, including all necessary excavation and earth work in any type of soil, returning, filling in, disposal of surplus soil to a distance n.exc 50m and depositing where directed, PCC in foundation of the mix (1:4:8), type D2 (Using 40mm graded crushed stone aggregate) stone masonry in cement mortar 1:4),rendering,10mm thick in cement mortar (1:4), internally finished even and fair and pointing flush externally as the work proceeds in the same mortar . Mild steel angle iron 75x75x6mm frame of MS sheet cover 3mm thick with handle and locking arrangement, painting all the exposed surface MS work with two coats of synthetic enamel paint, all the MS embedded in PCC with two coat of black bituminous paint suitable for 50mm dia complete all as specified.

M & L for road cutting depth upto 1.5 mtr below the normal ground level to laying pipe lines cables etc across the road in horizontal position and making good the disturbed portion to match with the exising surfaces complete all as specified and directed.

M/S M S Constructions

Hansraj Shivhare