CONSTRUCTION OF STORE ROOM IN THE OFFICE OF HQ CWE (AF) AGRA AGAINST JOB CONSTRUCTION OF ROAD ABEAM GOLF TAXI TRACK AT AF STN AGRA

Amount

Excavating in post holes (or similar holes) each not exc 0.50 Cum, getting out in soft/loose soil, returning, fillin in and rammingt earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete incl removing excavated material not exc. 50 m and depositing where directed complete all as specified and as directed.

M & L for providing cement concrete type C-2, (1:3:6) (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for mild steel work as in posts or strutes including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc) incl all necessary bolting or riveting and spot welding etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

M&L for roof trusses (frames) trussed purlins, bracing cranes gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and as directed.

S&F mild steel works as in wind ties for roof incl securing bolts, posts and struts in fencing incl cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) incl all necessary drilling, bolting or riveting ect and similar work conforming to Fe-410-O or FE 310-0 upto any heigt of bldg complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick or an colour having tensile strength of 550 MPa 150 GSM as in roof covering/cladding to wall fixed withs self tapping screws complete all as specified and as directed

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick or an colour having tensile strength of 550 MPa 150 GSM as in roof covering/cladding to wall fixed withs self tapping screws complete all as specified and as directed

M&L for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and apply two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not exc 10 cm width or girth, not otherwise described and apply two coat of synthetic enamel paint over one coat of red oxide primer complete.complete all as specified and as directed.

M&L for brick work with fly ash modular bricks straight or curved on plan exc 6.00 m mean radiun radius built in CM 1:4 complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work/concrete surfaces finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces finsihed the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying two coat of weather proof exterior emulsion paint in normal pattern, over a coat of primer as per manufacturer instructions ccomplete all as specified and as directed.

M&L for two coats of distemper oil emulsion over newly plastered surfaces of wall including preparation of surfaces complete all as specified and as directed.

M&L for providing and applying average 1mm thick of Birla/JK wall care putty over prepared surfaces to acheive the surface even and smooth for painting, complete all as specified and as directed.

M&L for 40mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as in sub base of floor etc complete all as specified and as directed.

M&L for 8-10mm thick vitrified ceramic tiles, light shade double charged (square/rectangular) area of each tile not less than 0.36 Sqm in floors etc set and jointed in neat cement slurry and pinted in white or coloured cement to match including screed bed or bedding layer of 15 mm thick in CM (1:6) for laying floor finishes complete all as specified and as directed.

M&L for 8-10mm thick vitrified ceramic tiles, light shade double charged (square/rectangular) area of each tile not less than 0.36 Sqm in skirting etc set and jointed in neat cement slurry and pinted in white or coloured cement to match including rendering 15mm thick in CM (1:6) complete all as specified and as directed.

S&F false ceiling at all heights with semi perforated 12mm thick micro tegular edged GRG (Glass fibre reinforcement Gypsum) false ceiling tiles of size 595X595mm of approved texture, design and patterns having moisture content less than 2% humidity resistance of 995, NRCO 50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (Part-40 1970 and light reflectance of 855 (minimum) to be laid in true horizontal level suspen ded on interlocking metal T-grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @120 grams per sqm including both sides) comprising of main T runners of size 15X32mm of length 3000mm cross T of size 15x32 mm of length 1200 mm and secondary intermediate cross t of size 15X32 mm of length 600mm to form grid module of size 600X600 mm suspended from ceiling using galvanized mild steel items (galvanizing@80grams per sqm) i.e. 50mm long, 8mm long, outer diameter, M-6 dash fateners, 6mm dia fully threaded hangar rod upto 1000mm length and L-shape level adjuster fo size 85x25x2mm, Galvanized iron perimeter wall angle of 24X24X0.40mm length 3000mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450mm centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing complete all as specified and as directed

M&L for providing and fixing of sliding window/ventilator system fabricated from roll formed sections made of Galvanized steel colour coated/powder coated (Base Steel as per IS 513 "D" quality, Galvanized as per IS 277 with zinc of 120 grmas/sqm with total coated thickness of 0.58 m or Powder Coated with pure polyster powder upto 50-60 microns thick. Sections for three track external frame should be of 44X107mm, Section for window glass shutter should be of 35X49mm, Section for shutter horizontal mullion should be 22mmX60mm, Section for winsow euro groove should be 25x24mm (Aluminium/Plastic) and section for window Lap Strip should be of 21X4mm (Aluminium). Section for door glass shutter should be of 35X67mm Section for door eurogroove should be 25X31mm (aluminium/Plastic) and section for door Lap Strip should be of 39X41mm (Aluminium/Plastic). The windows/doors should be panelled with 5mm thick plain float glass. Gaskets are to be made with Ethyl Propylene Diamine Manoer (EPCM), Corner brackets for internal and external frame made of Polypropylene. Touch lock to be provided for window shutter. Sections are to be cut to length, joined and assembled by means of corner brackets. The above frame should be fixed to brick/concrete masonary by using Nylon self expanding caps and driving MS electroplated 80mm long screws into the caps through fraes. Grill for safety to be made with 25mmx4mm thick MS flat all around and 10mmX10mm MS square rod to be used for horizontals with spacing not more than 150mm and 10mmX10mm MS square rod to be used for verticals with spacing not more than 350mm complete all as specified and as directed. The grill be fixed to wall after fixing the windows. Note : (i) Glazed shutter with 5.50 mm thick glass, mesh shutter with 32 guage stainless mesh and MS grill as per above mentioned drawing is deemed to be inclusive in the rate quoted for unit. (ii) Glass, stainless steel mesh will be fixed to window by authorised rep of manufacturer of window only. (iii) Making good of jambs in CM (1:4) and OBD with putty complete.

S&F factory made UPVC white colour casement door with frame and SS friction (400X19X1.9mm) made of (big series) frame 67X64mm, sash 67X110mm & mullion 67X80mm all having wall thickness of 2.3+0.2mm and single glazing bead/double glazing bead of appropriate imension compising of UPVC multi chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60+0.2mm thick galvanized mild steel section made from roll forming process of required length (shape and size according to UPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, GI fasteners 125X8mm size for fixing frame to finished wall and necessary stainless steel screws etc, Profile of frame & sash shall be mitred cut and fusion selded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and as directed. Note : (i) For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth and width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (ii) It is deemed that rate of 8m thoughened glass is included in quoted rate.

M&L for reinforced cement concrete M-25 using 20m graded stone aggregates as in rafts, footings, foundation beams, plinth & lintel beams, bases for columns, basement slabs, under reamed piles and mass concrete incl all formwork and necessary excavation complete all as specified and as directed.

M&L for Mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

All as per Item No 23 Above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders quality confirming to IS complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins arches pillars etc excl ashlar facing dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6.0 M mean radius built in CM 1:4 complete all as specified and as directed.

Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. Inlcuding raking out joints, hacking for key, scrubbing down with water etc. Including removal or debries out side MOD land complete all as specified and as directed.

M&L for rendering 10mm thick in CM (1:3) on ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered ceiling surfaces and applying three coat of white washing complete all as specified and as directed.

Demolition of PCC in ground floors & pavings not exc. 15 cm thickness (below or above ground level) (unreinforced) complete all as specified and directed.

S&F 605mm x 605mm anodised aluminium snap grid frame work for false ceiling and 4mm thick non asbsestos fibre cement building board of approved make design fixed or laid/inserted to Aluminium framework with screws as per manufacture's instructions complete all as specified and as directed.

Taking down chowkhats or frames with shutters exc 1.5 Sqm but not exc. 4.0 Sqm each (without taking off shutters from the frame) incl repairing of jambs in CM 1:4 complete all as specified and as directed.

Taking down chowkhats for frames with shutters not exc 1.5 Sqm (without taking off shutters from the frame) incl repairing of jambs in CM 1:4 complete all as specified and as directed.

S&F in position powder coated (any colour and thickness of coating not less than 50 micron) aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F powder coated (minium thickness of powder coating 50 micron) Aluminium door shutters, aluminium section weighing 0.55 Kg / m including necessory joining cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and as directed.

S&F powder coated Aluminium (sliding type) window and ventilators with three track bottom track size 92X29.5X2 mm thick, side and top track size 92X29.5X2 mm and shutters aluminium anodised 39X20X2 mm thick including necessary fittings like joints cleats, glazing clips, rubber packing, anodised aluminium snap beading screws etc with and including 5mm thick tinned glass in panels including all fittings and fixtures complete all as specified and as directed.

S&F 5.50 mm thick figured glass ordinary quality and fixing with oil putty or rubber/ wooden/ aluminium beads and provsion of glazing pins where required in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S&F 0.36 mm dia stainless steel wire cloth with average width of aperature 1.40 mm and fixed with stainless steel wire staples or moulded beading complete all as specified and directed.

S&F anodized aluminum grill, 10mm thick diamond shape with aperture 75mm fixed to windows frame with CP brass/stainless steel screw @200mm c/c including cutting the grill to proper opening size complete all as specified and as directed. Make - Deco Grill, model DG-104 or equivalent in Jindal/Hindalco.

M&L for 75 mm thick cement concrete type C-1 (1:3:6) (using 20 mm stone graded crushed stone aggregate) as in plinth protection surface finished even and fair including forming construction (dummy) joints 6 mm wide & 10 mm deep and filled with filler at an interval not exceeding 3 metre and at change of direction complete all as specified and directed.

S&F in repair venetian blends in double layers roller type of approved colour including all items for fixing the same in windows complete all as specified and as directed.

Demolition of RCC of any description and in any position complete all as specified and as directed.

M&L for RCC (Design Mix) M-25 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; linth beams; bases for columns, etc. basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Use and waste of form work to soffits of suspended slabs, floor slabs, chhajja and similar work not exceeding 200 mm thick (Horizontal or sloping) for rough finished and flat surface of concrete complete all as specified and directed.

M&L Hardcore of gauge not exc 63mm, deposited, spread and levelled in layers not exc. 15 cm thickness,watered and rammed to a true surface of broken stone complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and as directed.

M&L for RCC (Design Mix) M-25 (using 20mm graded stone aggregate) as in beam, cantilevers, bressumers, lintel over 1.50 metre clear span and like complete all as specified and as directed.

Use and waste of form work to sides of beam and soffit of roof beams, with rough finished flat surface complete all as specified and as directed.

M&L framed work such as grills grating, grider etc with ends of bars shouldered and/or riveted, or fogged into spikes framed guard bars, barred iron doors, ladders framed balusters, walk ways, railings frame work of water tanks and similar work conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

Sethi Brothers (BID ID -3268824)

M/s Krishna Construction Company (BID ID -3257264)

aman construction & general suppliers (BID ID -3268620)