Kallakuruchi Dist Chinnasalem Block Construction of Panchayat office building at poondi panchayat

Amount

Construction of Panchayat Office Building @ Poondi Panchayat

Earth work excavation and depositing on bank with intial lead and lift in all clasuses of soil such as Hard Gravely soil, Gravely soil except Hard Rock requiring Blasting etc complete as per SS20B for narrow foundation

Cement Concrete 1:4:8 mix using 40mm ISS HBG stone jelly for Foundation and flooring including cost,conveveyance of all materials and labour charges to laid in layers not more than 15cm thick, well rammed etc, complete with standard specification

ReFilling in Basement with Excavated Earth in Layers of not more than 15 cm thick , well watered,rammed and consolidated complying with standard specification etc complete .

Supplying and Filling in Basement with Filling Sand in layers not more than 15 cm thick , well ramed and consolidated complying with standard specification

Supplying and Erection centering for sides and soffiots including necessaary supports and strutting as directed by the departmental officers. Rate for 10m2 for the following items (RCC floor slab, roff slab, Rectangular / Square, Tee/ Ell beams, Lintels, StairCase Waist Slablanding slab landing beam Canopy etc in all floors with all cross Bracings using mild steel sheets of size 90cm x 60cm and 10BG stiffened withmild steel angles of size 25mmx3mm for boarding laid over country wood joists of size 10cmx6.50cm spaced at about 90cm centre to centre and supported by Casurina props of 10cm to 13cm dia spaced at 75cm centre etc, complete and as directed.

For Below GL Centering

Above GL

For Sill Slab Lintel, Portico Beam

Supplying, Fabricatung and placin g in position of RTS or MS rod for all reinforced cement concrete works as per design given including cost of steel and binding wire in all floors etc,complete complying with standard specification

Reinforced cement concrete in 1 : 1.5 : 3 , mix using 20mm iss HBG stone jelly for all reinforced cement concrete works excluding cost of centering and stell but including laying,vibrating,curing and finishing ,fixing fan clamps in the RCC floor and roof slab works wherevver necessery and bearing surface of the wall at the sides and bottom of the slab, beam shall be finished smooth with cement mortor 1:3 and craft paper without claiming extra cost.,complete compying with standard specification and as directed by the departmental officers

Grade Beam

GRB to Basement

Brick Work in Cement Mortor 1 : 5 mix using Country Bricks of size 22 x 11 x 7 cm including cost and conveyance of all materials and labour charges etc complete .

Upto Basement

Superstructure

Plastering with Cement Mortor 1:5,12mm thick including cost and conveyance of all materials and labour charges including curing etc., complete complying with standard specification as directed by the departmental officers

Plastering with Cement Mortor 1:3 ,20mm thick including cost and conveyance of all materials and labour charges including curing etc., complete complying with standard specification as directed by the departmental officers

Special Ceiling Plastering and finishing all RCC exposed surfaces such as RCC Slabs,Canopies,sunshades,landing slab Beams ,etc with CementMortor 1:3, 10mm thick (one cement and three sand)including cost and conveyance of all materials and labour charges etc complete as directed by the departmental officers etc complete complying with standard specification.

Weathering Course Concrete by using best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be added) over the RCC Roof slab in the proportion of brick jelly to lime being 32 : 12.5 by volume and laid in a single layer and consolidated to the required slope and finished thickness by beating the concrete with wooden beaters if approved pattern keeping the surface constantly wet by sprinkling Lime jaggery water as per standard specification etc., complete as directed by the departmental officers.

Finishing the Top of Roof with one course of PRESSED TILES of size 23 cm x 23 cm x 2 cm of approved quality laid in cement mortor 1 : 3 (one cement and three sand ) 12 mm thick mixed with water proofing compound confirming to IS at 2% by weight of cement used and the Top pointed with same mortor mixed with redoxide to the full depth of Tiles , complete coplying with standard specification(The rate inclusive of redoxide and water proofing compound ) and as directed by the departmental officers .

Paving the Floor with best quality Vetrified Tiles of Size 600 mm x 600 mm of approved colour, shade and quality laid in cement mortor 1 : 3 (one cement and three sand ) 20 mm thick in all floors and the top pointed with the white cement mixed with same colouring Pigments and as directed by the departmental officers etc complete complying with standard specification

Providing granolethic floor finish in cement concrete 1:2:4 mix using 10-12mm ISS metal including cost and conveyance of all materials to site

Dadooing walls with colour designed Glazed Tiles of sizes 300 mm x 200 mm x 6 mm size of approved make and quality and colour set in cement mortor 1 : 2 ( one cement and two sand ) over 10 mm base layer plastering and pointing with white cement neatly as directed .

Supply of Mild Steel Door of size 1.10 m x 2.10 m with Two leaf. Outer frame o f40 x 40 x 6 mm equal MS Angle , Shutter frame made of 35 x325 x 5 mm equal MS Angle for horizontal and vertical members and the shutter frame strengthened by stiffners of one horizontal for each shutter using MS Plate of size 20 x 5 mm fully covered with 18 Gauge plain MS full sheet welded with shutter frame neatly and also fixin by welding ,Tower Bolts 30 cm long , Butt Hinges two nos of locking handles fixing the shutter including painting the whole unit with one coat of best quality red oxide Primer .

Supply of Mild Steel Door of size 1.00 m x 2.10 m with Two leaf. Outer frame o f40 x 40 x 6 mm equal MS Angle , Shutter frame made of 35 x325 x 5 mm equal MS Angle for horizontal and vertical members and the shutter frame strengthened by stiffners of one horizontal for each shutter using MS Plate of size 20 x 5 mm fully covered with 18 Gauge plain MS full sheet welded with shutter frame neatly and also fixin by welding ,Tower Bolts 30 cm long , Butt Hinges two nos of locking handles fixing the shutter including painting the whole unit with one coat of best quality red oxide Primer .

Supply of Mild Steel Door of size 0.75 m x 2.10 m with Two leaf. Outer frame o f40 x 40 x 6 mm equal MS Angle , Shutter frame made of 35 x325 x 5 mm equal MS Angle for horizontal and vertical members and the shutter frame strengthened by stiffners of one horizontal for each shutter using MS Plate of size 20 x 5 mm fully covered with 18 Gauge plain MS full sheet welded with shutter frame neatly and also fixin by welding ,Tower Bolts 30 cm long , Butt Hinges two nos of locking handles fixing the shutter including painting the whole unit with one coat of best quality red oxide Primer .

Supply of Mild Steel Window of size 1.20 m x 1.30 m with Two leaf. Outer frame of 35 x 35 x 5 mm equal MS Angle , Mullion section made of 35 x 35 x 5 mm equal Tee section , Shutter frame made of 25 x 25 x 5 mm equal MS Angle for horizontal and vertical members and the shutter frame strengthened by stiffners of one horizontal for each shutter using MS Plate of size 20 x 5 mm fully covered with 18 Gauge plain MS full sheet welded with shutter frame neatly and also fixin by welding , protective grill with 12 mm square M S rods at an interval of not greater than 10 cm centre to centre to the outer frame , two nos peg stays with hole for keeping the windows open in different positions , two nos of locking handles fixing the shutter with four nos of hinges hold fasts , six nos of hinges with outter frame of the window including painting the whole unit with one coat of best quality red oxide Primer .

Supply of Mild Steel Window of size 1.50 m x 1.30 m with Three leaf. Outer frame of 35 x 35 x 5 mm equal MS Angle , Mullion section made of 35 x 35 x 5 mm equal Tee section , Shutter frame made of 25 x 25 x 5 mm equal MS Angle for horizontal and vertical members and the shutter frame strengthened by stiffners of one horizontal for each shutter using MS Plate of size 20 x 5 mm fully covered with 18 Gauge plain MS full sheet welded with shutter frame neatly and also fixin by welding , protective grill with 12 mm square M S rods at an interval of not greater than 10 cm centre to centre to the outer frame , two nos peg stays with hole for keeping the windows open in different positions , two nos of locking handles fixing the shutter with four nos of hinges hold fasts , six nos of hinges with outter frame of the window including painting the whole unit with one coat of best quality red oxide Primer .

Supply of Rolling Shutter of size 1.20 m x 2.10 m with frame and locking arrangements etc complete

Supply and fabrication of Steel Grill Gate of over all size of 1.50 m x 2.10 m using structural steel etc complete in all respects as directed

Supply of RCC JOLLY of size 0.90 m x 0.45 m etc complete

Supply and Fixing of Rcc Jolly of size 0.60 m x 0.45 m including cost and labour charges etc complete

Fixing charges for Steel Door in position etc complete

Fixing charges for Steel Window in position etc complete

Fixing charges for Jolly in position etc complete

Supply of Cudappa Slab 20 mm thick including cost and conveyance to site and labour charges etc complte

Fixing charges for Cuddapa in position etc complete

Fixing charges for Grill Gate in position etc complete

Plastering in Cement Mortor 1 : 3 mix to 20 mm thick including cost and conveyance of all materials to site and all labour charges for mixing, laying and curing etc complete for 10 Sqm.

Distembering Two Coats with best approved Oil Bound Distember including cost of Painting with Primer Coat over new plastered surface and conveyance of all materils to site and all labour charges etc complete

Painting Two Coats with approved Exterior Emulsion over one coat of Primer Coat over plastered wall surface , ceiling and other new surface including cleaning , preparing the surface,curing,scaffolding charges etc, complete.

Painting Two Coats over Iron work including cost of paint and Labour charges etc complete

Providing and fixing PVC. RainWater Downfall pipes of size 110 mm diametre with necessary shoes,bends and other specials, clamps,screws,nailsteakwood plugs etc complete including cost of all materials. The rate include cost of removable cast iron Gratings of appropriate size.The size of Teak wood plugs to be used is 150 mm x 25 mm in front and 200 mm x 75 mm in rear and all other sides with a depth of 100 mm . The pipe is to be fixed by means of U clamps at the centre of the pipe to be fixed in addition to these for more than three metres pipie length , complete complying with standard specification

Suppling and fixing in position of Indian Water Closet Coloured of size 580 mm x 440 mm , white Glazed earthen ware of approved quality with P trap or S trap confirming to is:2556 - Part XII with sand cushion and forming the closet using 40mm broken jelly lime concrete etc complete

Suppling and fixing in position of European Water Closet Coloured with " P " or " S " Trap with Double Flapped seat and seat cover with Brass Hinges and 10 Litre capacity PVC Low level Flushing Tank with all internal fittings of size 580 mm x 440 mm , white Glazed earthen ware of approved quality with P trap or S trap confirming to is:2556 - Part XII with sand cushion and forming the closet using 40mm broken jelly lime concrete etc complete

Supply and Fixing of Coloured Wash Hand Basin with Pedestal of Size 550 mm x 400 mm with all accessories such as cast iron Brackets , 32 mm dia CP Waste coupling , rubber plug and chain , 32 mm dia " B " Class G I waste pipe, 15 mm dia GM wheel valve , 15 mm dia nylon connection , 15 mm dia brass nipples , 15 mm CP . Pillar Tap etc complete .

Hand Rails Stainless Steel by Manufacturing , Suppying and Fixing of Stailess Steel Hand Rails for staircase near wet riser using 50 mm dia 304 L Grade Stainless Steel pipe of 1.60 mm thick will be provided with Tubular supports made of 304 L Grade Stainless Steel pipe of 25 mm dia of 1.60 mm thick welded to the railing. The supports will be grouted into the wall and provided with 93 mm thick Stainless Steel Circular base plate of 304 Grade . the rate shall included for Grouting into concrete with necessary supporting arrangements the Hand Rail in Floor polishing buffing ,bonding , cutting , grinding , conveyance welding charges , electrical charges etc complete .

Wiring with 2 x 1.50 sqm ( 22/0.3 ) PVC insulated SC unsheathedCu Conductor of 1100 v Grade in suitable PVC Rigid Pipe Concealed in wall and ceiling with PVC accesseries,in flush with wall , with TW box 150 mm x 100 mm x 113 mm TW Switch box with 3 mm thick Hylem sheet cover for 5 A 3 Pin non inter locking CS plug with painting of suitable colour with contionues earth wire connection of 14 SWG TC Wire and making good of the concealed portion with suitable colour for Concealed Plug Point SD No 25 for PVC PLUG Point

Wiring with 2 x 1.50 sqm ( 22/0.3 ) PVC insulated unsheathed single core Copper Conductor of 1100 v Grade in suitable PVC Rigid Pipe concealed in wall and ceiling with PVC accesseries with TW Switch box with 5 A F . T . Switch and making good of the concealed portion with suitable colour for PVC Concealed Light Point and Fan Point S D N o 25

Supply and Fixing of fancy glass shade and 11 W CFL in the existing light point SDnO 80

Supply and fixing of single Box Type 4"40 W fiu fitting complete with copper choke and condenser with teak wood round blocks on wall or ceiling with fiu tube with PVC unsheathed Copper leads from terminals to the fitting SD No 88

Supply and fixing of 32 A DPIC Switch of 500 v with F & N ( Side Handle ) on suitable T W Box with PWD Earthing ( S D N o 143 )

Supply and Run of 2 of 6 sqmm ( 84 / 0.3 ) PVC insulated single core unsheathed Copper Conductor of 1100 v Grade on 7 / 20 G I Bearer wire for Service Connection Mains ( S D No 66 )

Supply and Run of 2 of 6 sqmm ( 84 / 0.3 ) PVC insulated single core unsheathed Copper Conductor of 1100 v Grade in 25 mm dia G I suitable Pipe B class suitably bended both ends with necessery angle iron upright and end support For Mains ( S D N 71 )

Supply and Fuixing of Water TIGHT Bulk Head fitting with Guard suitable for 11 w lamp with CFL SD No 83

Supply and fixing of 1200 mm ( 48" ) A C Ceiling Fan complete with stepped eloctronic 300 w regulator with 1.00 meter down Rod on the existing clamp S D N o 107

Supply and fixing of TNEB meter Board suitable for 32 A Single Phase SC . With 32 A Fuse Unit etc complete . SD No 125

Provision for EB Deposit charges

Provision for 1000 Litres HDF PVC Tank Ls @ 10.05 / litre

Provision for Pipe Line and Tap for Water Supply Arrangements

Provision for RWH Arrangements

Provision for Name Board

Provision for Photographic charges

Provisionm for LWF 1.00 % etc.

QC Test 0.05% etc.,

Er Constructions (BID ID -1319425)