CIVIL WORKS FOR SITE PREPARATION AND UPGRADATION FOR ESTABLISHMENT OF AUTOMATED PLATING SHOP

Supplying and spreading approved quality morrum in layers including watering,ramming,levelling and proper compacting attain uniform & levelled surface by spraying water and keeping wheels wet during operation or plate vibrator whereever roller is not accessible, including hire charges of roller / vibrator,labour,cost of fuel,all other incidental charges,etc all as specified and directed by EIC.

Providing, laying and spreading compacted graded stone aggreagates of Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. : With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Dismantling of RCC work manually or mechanical means including core cutting including cutting of reinforcement and staking of steel bars and dispposal of unserviceable materials within 50 meter lead as per direction of EIC.

Dismantling of brick work built in cement mortor manually /by mechanical means including stacking of steel bars and disposal of unserviceable materials within 50 metres lead as per direction of Engineer-in-charge

Providing and laying in position cement concrete of 1:3:6 (cement:manuifactured sand derived from recycled concrete agrregates:stoen Aggregates of 40mm nominal size) in trenches, floor and foundations etc. work complete as per direction of EIC

Providing PCC1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying Plain cement concrete 1:1.5:3 by volumetric mix using 20mm and downgraded hard granite stone aggregate for Footing/Columns/pillars/posts/Beams/slabs etc

Providing random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 up to plinth level with cement mortar 1:6

Brick work with non modular fly ash bricks WITH CM(1:6) conforming to IS:12894,class designation 10 average compressive strength in super structure above plinth level up to floor V level in : cement mortar 1:6

Providing plastering by rendering 15 mm thick Cement mortar 1:6 (one part Cement : Six parts fine sand) over concrete / brick surfaces like ceiling, walls etc.,wherever required and finishing smooth and even, using trowel with all necessary scaffolding at all heights, etc., complete with rates including cost of all material, tools, labour, wastages etc., all as directed and approved by EIC.

Providing and fixing 20 mm thick acid and/or alkali resistant tiles (sample as approved by EIC with pattern, sizes and colour) in flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as perIS :4457, complete as per the direction of Engineer-in- Charge

Providing and fixing 10 mm thick acid and/or alkali resistant tilesIn dado/skirting on 12 mm thick mortar 1:4 (1 acid proofcement : 4 coarse sand) of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as perIS : 4457, complete as per the direction of Engineer-in- Charge

Complete removal of old oil bound distemper, cement paint paint by buffing machine or any other mechanism scrapping , sand preparation etc to give even surface to apply wall putty , the works includes at all heights with necessary safety measures

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer,over the plastered wall surface to prepare the surface even and smooth complete

Supplying and apply two coats of Wall painting with premium interior acrylic emulsion paint and one coat of water thineble primer, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture approved brand and manufacture, having low VOC (Volatile Organic Compound ) content., including applying additional coats wherever required to achieve even shade and colour.

Supplying and apply two coats of Acrylic smooth exterior paint and applying one coat of primer over old work on wall surface having VOC content less than 50 grms/litterof approved brand of approved brand and manufacturer having low VOC

Supplying and fixing UV stabilised 2mm thick corrugated FRP sheet roofing up to any pitch including fixing with overlaping, self driven screws, nuts and bilts etc, G.I plain / bitumen washers complete, sheet shall be2400 TEX panel roving incorporating minimum 0.3% ultra violet stabiliser in resin system. The sheet sahll opaque or translucent, clear or pigmentd, texturred or smooth as apecified

Supplying and fixing the self-adhesive modified bitumenous membrane 1.6 to 2mm thick of Dr. FIXIT/FOSROC make etc, APP(atactic polypropylene) membrane over the Galvalume sheet, work includes preparation of surface by thorough cleaning of sheet, dust and any other forieign materials, applying one coat of primer to ensure maxumum adhesion of the membrane to the metal surface with overlapping 75-100mm all as approved by EIC

Providing and placing in position 100 mm thick Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface,properly, all leads &lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Structural Steel work welded in built up sections/ framed work, including cutting,hoisting,MS plates fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete as per direction of EIC

Suppling and Fixing Pre-Painted galvalume aluminium zink coating GI based corrugated steel out side extended roof sheet 0.5mm thick with zinc coating not less than 275 grams/smt of any colour having tensile strength of 550 Mpa for gutters , fixed with self tapping screws as bend to required shape of tarpezoidal/ rectangular section including joints lapped minimum 40mm wide and gaps seal with silicone sealant, ends fixed in CM wherever necessary at all heights including making cut outs for fixing rain water pipes, cost of all material, labour tools, overlapping,scaffolding, wastages, including necessary safety measures, incidental charges complete in all respects and as directed and approved by EIC.

Providing and fixing stainless steel ( Grade 304) 10mm(4 inch) scheduled 10S wall thickness not less than 3.05mm pipes made of Hollow tubes, channels, posts,plates, railing etc., including linked chain, welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Supplying and fixing transparant polycarbonate sheet of 10mm thick co extruded UV coated with light transmission of not less than 80% to fix in structural/wooden members with required screws, labour and lift charges, all as specified and directed by EIC.

Providing and fixing aluminium profile in between joints of polycarbonate sheet with necessary screws and fittngs all complete and handing over the useful materials to stores with in a lead of 200m including cost of labour,tools ,etc as directed by EIC.

Providing and fixing PCGI Double/single leaf Door of 46mm thick shutter are made out of 0.80 MM thick PCGI sheets filled with PUF and necessary reinforcement of NICOMAC/ICLEAN/CELESTRA make or equivalent with double skin view glass of 500x 750 mm on shutter using 6mm toughened clear float glass including necessary beading ,sealing all joints with silicon sealant,push plate, etc with necessary SS hinges with ball bearings/pivots, handles ,arrangement for fixing in walls /panels and providing of concealed hydraulic door closers of DORMA /NICOMAC /ICLEAN /CELESTRA.

Providing and fixing PCGI sencer operated and motorised sliding Door of approximate size 2.7m x 3 m and 46mm thick are made out of 0.80 MM thick PCGI sheets filled with PUF and necessary accessories like sliding guide rail and rollers reinforcement and etc of NICOMAC/ICLEAN/CELESTRA make or equivalent with double skin view glass of 500x 750 mm on shutter using 6mm toughened clear float glass including necessary beading ,sealing all joints with silicon sealant,push plate, etc with necessary SS hinges with ball bearings/pivots, handles ,arrangement for fixing in walls /panels and providing of concealed hydraulic door closers of DORMA /NICOMAC /ICLEAN /CELESTRA.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section,apperture and fixed to the existing window frame with C.P.brass/ stainless steel screws @ 200 mm centre to centre, including aluminium beading all around, cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

Dismantling steel work / rolling shutters manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge

Providing and fixing Pre -laminated medium density fibre board exteriorgrade (Grade-I) IS:14587:1998 marked, to frame, backing or studdingwith screws etc. complete ( Frames, backing or studding to be paidseparately) Pre-laminated with decorative lamination on both side exteriorGrade - I MDF Board 12 mm thick confirming to IS:14587

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal tegular/silhoutte suspended grid, inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12mm mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Supplying and fixing of MS welded hard dreawn steel wire fabric of size 25mmx25mm or required size wire mesh to be fixed& firmly anchored to the concrete/steel surface by means of L shaped mild steel shear key welded with existing reinforcement or steel including thje cost materials, labour, tool&plants as per directed by EIC

Providing and laying 60mm thick cement concrete paver block of M-35 grade of Classic make with approved colour, design & pattern factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light trafficparking etc, of required strength, thickness & size/ shape, made bytable vibratory method using PU mould, laid in required colour &pattern over 50mm thick compacted bed of sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator,filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

Providing and fixing in position (at any ht.& level) three track glazed, Aluminium powder coated sliding windows with sections conforming to JINDAL catalogue including providing & fixing 4.80 to 5.00mm thick plain float glass of MODI / SAINT GOBAIN make with one panel steel fly mesh shutter and good quality rubber / nylon gaskets, providing and fixing standard Aluminium 75mm handles, locking arrangement, necessary wheel / rollers etc.,. The windows shall be fabricated with Aluminium extrusions as described below of series B: a) Bottom member two track section 92 x 31.75 x 1.20 mm. b) Top & sides of two track section 92 x 31.75 x 1.30mm. c) Shutter top & bottom 40 x 18 x 1.29mm d) Shutter interlock 40x27x 1.29mm e) Shutter handle side 40 x 18 x 1.29mm complete with rates including cost of material ,tools, labour, transportation etc., all as directed and specified by EIC. [Gaps between wall / beam and Al. member shall be filled with slicon and made good].

Providing and erecting partly glazed and partly panelled powder coated Aluminium partition using standard sections of JINDAL or HINDALCO so that each pannel shall not exceed 1.20 SQM with 12mm thick pre-laminated board having twin finish of Novopan / TESA in bottom rows and 5mm thick float glass of MODI / ST GOBAIN on middle and top rows including glazing clips, rubber gasket for fixing the glass, filling gaps with silicon sealant,strengthening the partition by taking the required intermediate vertical members up to roof lvel, etc. Specification for aluminum sections to be used is a) Bottom members -95.25 x 44.45x 2.0mm b) Top / vertical members - 63.50 x 38.10 x1.95mm c)Middle memebers - 63.50 x 38.10 x 1.95mm.

Providing, manufacturing and erecting Partly glazed and partly panneled single / Double leaf Aluminium door using standard anodized powder coated sections of JINDAL, HINDALCO make as detailed below all of approved make.(Including necessary screws,fasteners,cleats,rods etc.Specification for each shutter :-a) Bottom members -97.30 x 44.45x 2.15mm b) Top members - 47.62x44.45x1.95mm c) Side member - 47.62 x 44.45 x 1.82mm d) Middle member - 49.91 x 44.45 x 1.60mm; Door member of SL NO19566 of JINDAL e) 12mm thick pre laminated twin finish exterior grade of Novapan MFPB (PTX) - Superior grade or TESA / ASIS / ARCHIDPLY or any other particle board having ISI Mark or 11-12mm thick both side finished MDF boards f) Glass - 5.00mm thick plain float glass of MODI / SAINTGOBAIN make g) Rubber gaskets - Good quality of approved make h) Glazing clips - Weight of 0.097Kg/RM. I) Aluminium/MS hinges 125mm long - 3Nos j) Aluminium handle 150mm long - 2 Nos. k) Concealed lock of make godrej/sheel 4 lever l) Aluminium tower bolts 200mm long - 2 Nos. m)Miscellaneous -Al. cleats, screws ,Door sealant, etc

Supplying and Fabricating TMT (Fe 500 grade) reinforcement bars conforming to IS, for reinforcement in RCC works as per drawings, including cutting, bending, lapping, hooking, welding wherever required and placing in position with binding wires at all levels and position. Binding wire shall be of approved quality and of 16 SWG, complete with rates including cost of all material, labour, wastages, transportation charges etc., all as directed and approved by EIC.

Providing and removing form work to all RCC members like columns,retaining walls, footings,tie beams, roof beams,slabs, lintels, etc., by providing 12mm thick marine plywood sheets supported on ACROW span shuttering with all supports, struts, wedges, scaffolder, bracings, runners,tie rods,ladder gangways,dressing with shuttering oil including MS nails, temporary openings, internal / external splayed, rounded edges or grooves for forming throating etc. complete all as specified and directed by EIC.

Supplying and Fixing 18mm thick mat finished / polished Granite slabs for slab of required size of approved quality, colour, texture and finish, jointed with cement slurry and pointed with cement mixed with pigment to match the colour, laid over a screed of Cement Mortar 1:6 (One cement : Six coarse sand), 25mm minimum thick including wastages,curing complete with rates including cost of all material,labour,tools,transportation etc., complete all as approved, specified and directed by Engineer In Charge.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily etc, including cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer- in-charge, curing etc., complete for finished item of work in all floors.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick).The aluminium composite panel cladding sheet shall be coil coated,with Kynar 500 based PVDF / Lumiflon based fluoropolymer resincoating of approved colour and shade on face # 1 and polymer(Service) coating on face # 2 as specified using stainless steelscrews, nuts, bolts, washers, cleats, weather silicone sealant,backer rods etc.The fastening brackets of Aluminium alloy 6005 T5 / MS with HotDip Galvanised with serrations and serrated washers to arrestthe wind load movement, fasteners, SS 316 Pins and anchorbolts of approved make in SS 316, Nylon separators to preventbi-metallic contacts all complete required to perform as perspecification and drawing The item includes cost of all material &labour component, the cost of all mock ups at site, cost of allsamples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection ofthe curtain wall with aluminium composite panel cladding till thehanding over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.sThe Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics allcomplete , as per the Architectural drawings, as per itemdescription, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purposeof payment, only the actual area on the external face of the curtainwall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Suppling and Fixing Pre-Painted galvatume aluminium zink coating GI based corrugated steel crimp curve out side extended roof sheet 0.5mm thick of any colour having tensile strength of 550 Mpa for gutters , fixed with self tapping screws as bend to required shape of tarpezoidal/ rectangular section including joints lapped minimum 40mm wide and gaps seal with silicone sealant, ends fixed in CM wherever necessary at all heights including making cut outs for fixing rain water pipes, cost of all material, labour tools, overlapping,scaffolding, wastages, including necessary safety measures, incidental charges complete in all respects and as directed and approved by EIC.

Providing and constructing brick work with best locally available fly ash frogged bricks in CM 1:6 for superstructure and below ground levelfor walls etc., for half brick thickness (115mm thick) including raking out joints 10mm deep to receive plaster. Scafolding, curing cost of all materials, labour etc., complete, with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Providing and fixing 15mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Providing and fixing 20mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Providing and fixing 25mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Providing and fixing 50mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Supply and fixing heavy duty Drain Cover grill made of PVC 20-25mm thick of approaximately 400mm wide, complete with rates including cost of all material,labour,tools,transportation etc., complete all as approved, specified and directed by Engineer In Charge.

Kota stone 25mm thick slab of flooring laid over 20 mm (average) thick base and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand), including cost of labour,tools ,etc as directed by EIC.

Supplying, laying the korean grass turf of good quality prepared with the proper levelling and ramming complete etc, rates including cost of supplying and spreading the good red earth and dump manure mixing with all proportionate and material,labour,tools,transportation etc., complete all as approved, specified and directed by Engineer In Charge.

Providing and fixing Aluminum body hydraulic Door Closer of designated type B of Everite / Hardwin/ Universal make conforming to IS 3564 to the doors with necessary screws etc. complete as specified and directed by EIC.

Supplying and Fixing White glazed porcelain IWC of orissa pan type of (PARRYWARE/HINDWARE/CERA/JOHNSON etc. or equvalent) approved make confirming to IS of size 580x440mm with intergal type of footrest with 'P' or 'S' trap,with 10 lits low level PVC flushing cistern including flush pipe with manually controlleddevice (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: , complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing white glazed vitreous china or porcelain European water closet (EWC) of (PARRYWARE / HINDWARE/CEAR/JOHNSON ETC or equivalent) approved make, confirming to IS-7231, with 10 litre low level white PVC flushing cistern, flush pie and manual controlled deivice(handle lever) with all necessary required fittings and fixures with 'P' or 'S' trap, with or without vent set, including supplying and fixing double flapped seat cover of same make etc., complete with rates including cost of material, labour charges, tools, lifts, leads, transportation etc.,all as approved, specified and directed by EIC.

Supplying and Fixing of 15mm dia G.I pipes 'B' class of (Tata or Zenith or equivalent) approved make with GI assorted fittings of HB or Zoloto make at all heights complying to IS and fixing in masonry with holder bat clamps, chasing in the brick walls and embedding the GI pipes and covering the same with CM including cutting holes in any walls or RCC., stroage tank connections and repairing the same in CM or excavation in trenches in all soils upto a depth of 450mm below ground level and refilling the same with excavated earth and watering and consolidation after pipe is laid as per requirement at site all as directed by EIC, complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and Fixing of 20mm dia G.I pipes 'B' class of (Tata or Zenith or equivalent) approved make with GI assorted fittings of HB or Zoloto make at all heights complying to IS and fixing in masonry with holder bat clamps, chasing in the brick walls and embedding the GI pipes and covering the same with CM including cutting holes in any walls or RCC., stroage tank connections and repairing the same in CM or excavation in trenches in all soils upto a depth of 450mm below ground level and refilling the same with excavated earth and watering and consolidation after pipe is laid as per requirement at site all as directed by EIC, complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and Fixing of 25mm dia G.I pipes 'B' class of (Tata or Zenith or equivalent) approved make with GI assorted fittings of HB or Zoloto make at all heights complying to IS and fixing in masonry with holder bat clamps, chasing in the brick walls and embedding the GI pipes and covering the same with CM including cutting holes in any walls or RCC., stroage tank connections and repairing the same in CM or excavation in trenches in all soils upto a depth of 450mm below ground level and refilling the same with excavated earth and watering and consolidation after pipe is laid as per requirement at site all as directed by EIC, complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying 150X150 mm SWG gully trap with CI cover along with suitable CI frame complete with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing of 32mm CP bottle trap complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Supplying and fixingof PTMT Soap dish/ tray complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Providing and fixing white vitreous china infrared sensor operated urinal of size 610x390x370mm along with with providing and fixing electric sensor also including providing fxing with ,CP waste coupling ,Spreader, brackets, HB elbow, bottel trap, with necessary screws etc., complete including cutting and making good the walls, and floors, where required complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.urinals Providing and fixing white vitreous china battery/electrical infrared sensor operated urinal with CP waste coupling , 3 bolts, nuts, screws etc., complete including cutting and making good the walls, and floors, where required complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/clerestory windows & desertory other Frames/Chowkhat of 45x70mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

Providing and fixing factory made 30mm thick single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/ mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

Supplying & Fixing 5 mm thick beviled edges with sideless with SS/CP screws/ studs etc looking mirrors of size 600X450MM complete, with rates including cost of material, labour charge tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing of 75mm dia CI pipe of NECO / HEPCO make or equivalent confirming to IS 1729 as approved make, with ISI mark, with air tight cement caulked joints, testing for leakages cutting / making openings in brick masonary / CRS masonry wall / RCC / PCC etc. for taking out the pipes and making good with CM complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing of 100 mm dia CI pipe of NECO / HEPCO make or equivalent confirming to IS 1729 as approved make, with ISI mark, with air tight cement caulked joints, testing for leakages cutting / making openings in brick masonary / CRS masonry wall / RCC / PCC etc. for taking out the pipes and making good with CM complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing 100mm dia CI plain / plug bend or offset of approved quality and make, with ISI mark ,with air tight cement caulked joints testing for leakages cutting / making openings in brick masonary / CRS masonry wall RCC, PCC etc for taking out the pipes and making good with CM complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing 75mm dia CI plain / plug bend or offset of approved quality and make, with ISI mark ,with air tight cement caulked joints testing for leakages cutting / making openings in brick masonary / CRS masonry wall RCC, PCC etc for taking out the pipes and making good with CM complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing 75mm dia CI plain / plug Tee or Y offset of approved quality and make with ISI mark with air tight cement caulked joints testing for leakages cutting / making openings in brick masonary / CRS masonry wall RCC, PCC etc for taking out the pipes and making good with CM complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing 100mm dia CI plain / plug Tee or Y offset of approved quality and make with ISI mark with air tight cement caulked joints testing for leakages cutting / making openings in brick masonary / CRS masonry wall RCC, PCC etc for taking out the pipes and making good with CM complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing 100mm dia in trenches, to proper level, gradient and alignment, SWG pipe of approved quality and make with air tight cement caulked joint, testing for leakage all as directed including making connection to the existing man holes wherever required, complete, with rates including cost of material, wastages, labour charges, tools, lifts, leads, transportation etc., except cost of earth work (excavation and back filling will be paid separately), all as approved, specified and directed by EIC.

Supplying and Fixing Ceramic floor tiles of (KAJARIA / NITCO / JHONSON / REGENCY) approved make, coloured glazed ceramic tiles of size 600x1200, 8 mm thick, for floors of approved make and design fixed over CM 1:4, 20 mm thick and pointing with and grey cement slurry @ 3.3 kg per sqm including pointing / filling the joint with joint filler of approved make /quality of matching shade complete. including cost and conveyance of all materials like cement, sand, water, tiles, white cement , joint filler etc to site, including cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer- in-charge, curing etc., complete for finished item of work in all floors.

Providing & laying of 9mm thick ceramic tile dado/wall tiles of size 600x1200mm of (KAJARIA / NITCO / JHONSON / REGENCY) or equivalent make as approved by EIC laid over a bed of 15mm thick CM(1:4) base coat including pointing/fixing the jointing with joint fillersof matching color/shade of tiles including cost and conveyance of all materials and water to work site including cost of base coat, all operational, incidental, and labour charges such as mixing mortar, fixing in position, including lift charges, curing etc., complete for finished item of work in all floors.

Supplying and fixing of 20mm dia gun metal gate valves of below mentioned dia, of ZOLOTO / LEADER make or equivalent approved make & quality complying to IS, having screwed ends including fixing to the pipe lines with teflon tape etc., complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing of 25mm dia gun metal gate valves of below mentioned dia, of ZOLOTO / LEADER make or equivalent approved make & quality complying to IS, having screwed ends including fixing to the pipe lines with teflon tape etc., complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing white glazed porcelain counter type hand wash basin of 600 x 480mm size or equivalent approved size of (HINDWARE / PARRYWARE) make confirming to IS, including supplying and fixing 32mm waste coupling, 15mm dia CP angle cock , CP bottle trap, CP sensor based pillar cock, etc., of ESS / MARC / PARRYWARE or equivalent make, PVC inlet connection, CP wall caps with screws a pair of CI / MS brackets fixed in wall with screws, all above of approved quality complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing health faucet of approved by EIC make or equivalent make complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supply and fixing of paper holder with flap of PARRYWARE/ HINDWARE/ESS or equivalent make with all necessary connections complete as directed and specified by EIC.

Providing and fixing Glass urinal partition of 10mm thickness, nuts, screws etc, complete including cutting and making good the walls, and floors, where required complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Supply and fixing of brass tower bolt of size 250mm and 10mm dia approved make with all necessary screws etc complete as directed and specified by EIC.

Supply and fixing of Al tower bolt of size 250mm aand 10mm dia approved make with all necessary screws etc complete as directed and specified by EIC.

Supply and fixing of 1st class best seasoned teak wood for door frames / windows / ventilators / almarah frames etc., wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints and fixing with necessary hold fast screws, rawl plug etc., including cost of applying a coat of chloro pyriophos emulsiable concentrate confirming to IS 8944 - 2005 as per manufacturers specification, cost of all material, labour charges for fixing etc. complete for finished item of work as approved and directed by Engineer In Charge.

Supplying and fixing 110mm x 75mm diameter PVC Nahani trap of approved quality & make including finishing in CM 1:4 all as directed, approved and specified by EIC, complete with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing of 15mm dia CP long/short body bibcock" as approved brand of EIC or equivalent make etc all as directed, approved and specified by EIC, complete with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing of 15mm dia CP Angle cock "as approved brand of EIC" or equivalent make etc all as directed, approved and specified by EIC, complete with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing hanad dryer of make Viking or equivalent including with all necessary fittings etc complete with rates including cost of material ,tools, labour, transportation etc., all as directed and specified by EIC.

Supplying and fixing SS grab bar/rail of 24" length and 32-40mm dial with all required acessaries and fitting etc complete with rates including cost of material ,tools, labour, transportation etc., all as directed and specified by EIC.

Labour charges for removal of existing MS gutter including old brackets etc. and depositing the Serviciable material to civil stores, debrises off the premises. The work includes disposal of building materials, debrises etc to a initial lead distance, including loading, unloading.the work includes providing safety nets and scafolding are to be provided beneath the existing AC sheet roofing during the work execution of removal and fixing of material etc.Allcomplete as per specification & direction of EIC.

Supplying,carrying to site all approved materials, providing, fabricating and fixing in position of MS rain water gutter made out of 3.00mm(not less than3.00mm) of makes SAIL/TATA/RINL /JINDAL/BHUSHAN STEEL etc thick MS sheet including completely full welding at the joint on both sides, making holes for inserting rain water pipe and thorough welding around the pipes,making joints water tight and providing spouts wherever required including bending, turning to provide the shape for water troughs as per the site condition and connecting to the supporting framework for fixing rigidly either with welding or with riveting or nuts& bolts etc..the work includes providing of safety nets beneath the existing sheet roofing & gutter during the work execution of fixing and removal of materials etc The work shall be carried out at all heights with all safety precautions.All complete as per specification & direction of EIC.

Supply & carrying to site all approved materials and applying two coats of synthetic enamel paint to the steel surface or any other surface in all height and including application of one coat of redoxide zinc chromate primer for interior/ exterior steel surface as per manufacture guideline.etc. all complete as per specification & direction of EIC.The work shall be carried out at all heights with all sefety precaution.

Labour charges for removal of old asbestos /PVC pressure pipes of dia 150 mm or nearer any class (Including all fittings),including disconnecting pipe & fittings completely.The pipes are to be shifted from the site & deposited / dumped at the earmarked area/civil stores/salvage store etc.all complete as per specification and direction of Engineer-in-Charge.

Supplying, carrying to site all approved materials providing and fixing in PVC raindown pipes 160 mm dia or nearer single socketed pipes and having 4kg/ sqm pressure confirming to IS of SUDHAKAR/PRINCE/SIRIPLAST make etc of any length fixed to the wall surfaces / RCC columns/ steel structures with suitable clamps made out of 25x5 mm MS flat drilled and fixed with nuts and bolts at regular interval of 1.50mtr centre to centre the end of joints of the pipe are to be socket with suitable adhesive or grout materials etc. The nuts and bolts are to be grouted upto a depth of 75mm by making holes in RCC columns/ masonry wall by suitable pressure gun etc. all complete as per specification & direction of EIC. The work shall be carried out at all heights with safety precautions.

Supplying, carrying to site all approved materials providing and fixing in PVC (SWR) bends of dia. 160mm (ISI mark) of SUDHAKAR/PRINCE/SIRIPLAST make etc. all complete as per specification & direction of EIC. The work shall be carried out at all heights with safety precautions.

Taking out old damaged/ broken glass( any thickness, size, quality or description ) from metal frames including punching or drilling out old glazing pins/springs clips & refixing of old glass in the same location after the fabrication works for structural supports for gutters & gutter fixing works are completed. Safety nets of required size are to be provided under the roofing system during the execution of work etc. all complete as per specification & direction of EIC.The work shall be carried out at all heights with safety precautions.

Providing and fixing in position cast wired glass of 6.4mm thick in the wall cladding or to the aluminium or in metal frames in square,area of glass exc.0.5sqm but not exc.0.75sqm. The work also includes removal of old/damaged glass from the metal frame depositing any serviciable glass to store and rubbish off the premises. Safety nets of required size are to be provided under the roofing system during the execution of work. The work shall be carried out at all height with safety precautions.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading,transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Engaging / hiring proclainer (JCB / DOZER), including hire charges, driver charges, cost of fuel, lubricants and all other incidental charges required for operating the proclainer for clearance of heavy boulders/debris/RCC items /wooden logs, removal of excess/undulated earth and levelling the surfaces all as approved and directed by EIC.The job shall be executed taking all necessary precautionary measures.

Transplantation of trees up to girth 2.5mtr, works includes, trimming of branches up to height 20-30 Feet, and making root ball by earth work excavation around the tree and appling suitable chemicals,dressing, packing and burlaping and transporting to the earnmarked location within the HAl premises.(Contractor has to maintain the trees for 2 month at his own cost by providing/ transporting water at his own expenses. Water will be free of cost from STP or other source of HAL as per directions of EICL)

Supplying and providing FRP coating on structural steel and Galvalume sheet surface exposed to prone to corrosion works surface preparation involves thoughly cleaned,patching holes,and cracks after removal of rust and scales,As priming coat A resin coat is applied to the prepared surface and first layer of resin is applied to the surface either by brush or roller or spray, applied fiberglass reinforcement or woven roving layer and then final layer of resin is applied to encapsulate the fiberglass and provide a smooth protective surface.

Supply and fixing stainless steel name boards offer a durable, weather resistant engraved letters as per specifications given by HAL

Supplying and fixing Inauguration board engraved letters with granite board of size minimum 4'x5', write up will be given by HAL as specified complete all as per direction of EIC

Sub-total Rs.

(A) Quoted percentage (Excess or below)

(B) Sub-Total Amount excluding GST Rs. [after considering percentage at (A)]

(C)Add 18% GST on Value on (B) in Rs.

(D) Grand Total : [ B+C] in Rs.

GST SAC Code No

Example: 1. If the contractor wish to quote 5% below estimated amount, then they need to enter "- 5 %" in Green colour Column against Quoted percentage (Excess or below) 2. If the contractor wish to quote 2% excess over estimated amount, then they need to enter "2 % " in Green colour Column against Quoted percentage (Excess or below)

HINDUSTAN AERONAUTICS LIMITED

AVIONICS DIVISION::HYDERABAD

Pre-Qualification Profile

Estimated Amount in Rs.

Tender Notice Date:(DD-MM-YYYY)

Last date for submission of tender (DD-MM-YYYY)

Completion Period (In Months)

Name of the Individual / Firm / Company: * (Mandatory)

Type of ownership / Legal Status [Attach copies of the original document defining the legal status]

Year of Establishment of Company/Business

Registered Office Address, Telegraphic Address, Telephone No., Website / email id, FAX No.

Correspondance Address, Telegraphic Address, Telephone No., Website / email id, FAX No.

PAN no

PF number (If any)

ESI number

GST registration number

Particulars of registration with various Government bodies (Attach documentary proof)

a) Registration Number/s

b) Organization / Place of registration

c) Category [Limit for tendering]

Contact details

Contact person name

Designation

Mobile No.

Ph. No. with STD code

FAX No. with STD code

Email Id :

I.T Returns for past 03 years

Assessment year 2022-23 (i.e FY 2021-22)

Assessment year 2023-24 (i.e FY 2022-23)

Assessment year 2024-25 (i.e FY 2023-24)

Maximum value of works executed during the following 05 years and it should be certified by Chartered Accountant. (In Rs. Lakhs)

Turn over Criteria is Not met

DETAIL OF WORK ON HAND UPTO COMPLETION PERIOD OF SUBJECT WORK [Required for Bid capacity calculation] .Details are also to be furnished on Proforma-D

Sl.No(work No)

Bid Capacity

Action plan / bar chart as to indicate the completion of work, within the scheduled time (contract period)]

Bank(s) details: [Copy of the cheque leaf to be uploaded]

Bank Statement for past THREE months

Latest Over draft Facilities with Bankers

Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the final date of submission of Tender.

Required solvency value in Rs.

Name of Bank & Branch

Date of Issue (dd/mm/yyyy)

Value Rs.

Solvency value is NOT as per NIT

Experience of having successfully completed similar works during last 7 years ending on the previous day of submission of tender should be either of the following:. [ Work completion certificates along with LOA/PO/WO should be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated amount put to tender. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated amount put to tender. (iii) ONE similar completed work costing not less than the amount equal to 80% of the estimated amount put to tender.

Completed similar works during last 7 years

Work No I

Name of The organisation

Brief Description of Work:

Completed value of Work in Rs.

Date of Commencement of Work [DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Work No II

Name of The organisation

Brief Description of Work:

Completed value of Work in Rs.

Date of Commencement of Work [DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Work No III

Name of The organisation

Brief Description of Work:

Completed value of Work in Rs.

Date of Commencement of Work [DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

Date of Actual Completion of Work[DD/MM/YYYY]:

DETAILS OF TECHNICAL PERSONNEL AVAILABLE( if space provided is insufficient separate sheet to be uploaded with the same format as below)

PLANT, MACHINERY AND EQUIPMENT AVAILABLE [The Plant, Machinery and equipment (either owned or leased) that can be made available for this work must be furnished below].

Works of similar nature successfully completed in addition to Sl. No. (21) of Applicant Particulars (1) during the last 07 years ending last day for previous month.

Sl.No. (work No.)

Details of person holding the power of Attorney

Position

Mobile No.

Ph. No. with STD code

FAX No. with STD code/ e-mail ID

DECLARATION I

I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer . 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I//We are aware that document sought only be uploaded for evaluation of offer. 5. I/We shall not associate nor has been associated in the past, directly or indirectly with consultant or any other entity that would prepare the design, specification and other documents of the project.

DECLARATION II

I/We declare and undertake that - 1. To provide all facilities to HAL, Bangalore for verification of the information / details furnished by us and also for inspection of our works carried out / in progress if required. 2. The bid does not contain any amendment, modification as change of any type whatsoever in the bid documents and to any amendment issued thereafter.

EMD details

Description