WBPWD/EE/KNHED/e-NIQ-47/24-25

Amount

Dismantling of the existing LT panel , OLD Wiring and making necessary temporarry arrangement to cater electrical supply to all utilities. Incl temporary hiring LT panel,cables if required.

Supplying and fixing 415V, 200 A TPN SFU with sheet steel enclosure on flat iron/angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating ( make: ABB/Schneider/L-K)

Supplying and fixing double door 8 way Vertical TPN MCB with IP-42/43 protection, on angle iron frame on wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment, including Supplying and fixing double door sheet steel (16SWG), powder coated top and bottom end box for TPN DB vertical enclosure with IP-42/43 protection, on angle iron frame on wall & mending good the damages to original finish with nuts bolts etc incl. provision for earthing attachment Incoming: 200A, 415V, 10KA FP MCCB-1nos Out going: 63A, 415V, 10KA & C curve TP MCB- 7Nos, 6/32Amp SPMCB C curve -3 nos Cable End Bos ( 4 way)- 2 Nos (Make: Legrand/Schneider/L-K)

Supply & fixing of 415V, 4 way Horizontal TPN Double Door MCB Power DB complete with the following accessories and two number matching cable end box inside it and the same to be fitted after concealing the wall and mending good the damages as far as praticable as to G.S Incoming 63A 415V, 10KA FP MCB type isolator 1nos Out going (6-32A), 240V, 10KA & C curve SPMCB-12 nos Cable End Bos ( 4 way)- 1 Nos (Make: Legrand/Schneider/L-K)

Supplying and fixing double-doer 2+10 way SPN MCB Distribution Board with P 42/43 protection fitted on wall after cutting the wall & mending good the damages to original finish inct, Inter connection with suitable sice of copper wire and neutral link & provision for earthing attachment Incoming 32A 240V, DP MCB type isolator 1nos Out going (6A), 240V, 10KA & C curve SPMCB-10 nos Cable End Bos ( 6 way)- 1 Nos (Make: Legrand/Schneider/L-K)

Supplying and fixing 240 V, 6A SP MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection (Make: Legrand/Schneider/L-K)

Supplying and delivery of 1.1 KV grade armoured Alminium XLPE cable. (Make: Gloster/Havells/Polycab) 4 core 70 sqmm

4 core 16 sqmm

2 core 6 sqmm

Laying of cable from 3½ core 50 sqmm and upto 3½ core 90 on wall/surface incl. S & F MS saddles with earthing attachment in 2 x 10 SWG GI (Hot Dip) Wire, making holes etc. as necy., mending good damages and painting

Laying of cable upto 3/4 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting

Laying of cable upto 2 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting

Supply and fixing compression type glandcomplete with brass gland brass ring and rubber ring for dust and moisture proof entry of XLPE/PVC armoured cable. 4 core 70 sqmm

4 core 16 sqmm

2 core 6 sqmm

Finishing the end of following XLPE/PVC armoured cables bycrimping method incl. supplying and fixing solderless socket(Dowels make), tapes, anticorrosive paste & jointing materials 4 core 70 sqmm

4 core 16 sqmm

2 core 6 sqmm

Distribution wiring in 2 x 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (KEI/Gloster/Polycab) in 20mm size PVC rigid conduit 'FR' (Precision make), with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board cum JB on wall complete with 2 no. suitable size “Ph & N” copper bar incl. bakelite/Perspex (wall matching color) top cover 3 mm thick and incl. 175mmx100mmx65mm inspection box, making earthing attachment, painting the MS box and mending good the damages to original finish Average run 8 mtr

On Board

Average run 4.5 mtr

Supplying & Fixing sheet metal inspection box (16 SWG) of the following sizes flushed in wall by housing the same after cutting brick wall incl. making earthing attachment 175 mm x 100 mm x 65 mm

200 mm x 150 mm x 65 mm

Distribution wiring in 1.1 KV single core stranded 'FR' PVC insulated & unsheathed copper wire (KEI/Gloster/Polycab) in 20/25/32mm size PVC rigid conduit 'FR' (Precision make) incl. necy. fittings as required 2 x 22/0.3 (1.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC

2 x 36/0.3 (2.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC

2 x 56/0.3 (6 sqmm) + 1 x 36/0.3 (4 sqmm) ECC

Finishing of the PVC insulated wire ends by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes 2.5 sqmm

Fixing only starters (for motor control) on flat iron frame / angle iron frame on wall Direct on Line starter for motor (upto 5 HP) On angle iron frame [for existing]

Supply and fixing of Hylum Sheet of size 300mm x 200mm on wall by fastners, nut bolts incl. mending good damage

S & f of Bulkhead IP-65 with Plastic Body with S & f of 10 watt LED Lamp on wall ( Philips/Wipro/Magik)

Supply & delivery of Single LED Tube light fitting complete with 20 watt 2100 Lumen LED tube lamp making connection as to GS( Philips/Wipro/Magik)

Fixing only single/twin fluorescent light fitting suspended 25 cm bellow the ceiling with 2 No. 20 mm dia EI conduit (14 SWG) supports fixed with “L” type MS clamp whose one side fixed on ceiling with sutable size 4 nos. fastener and other side connected with the conduit with suitable size of bolts and nuts incl. S&F EI conduit, “L” type (125mmx125mm) 6mm thick and 25mm with MS clamps and connecting the length of PVC insulated wire and mending good damages to original finish and painting etc. by 2x24/0.20 mm (1.5sqmm.) flexible copper wire of 1.10 mt. length.

Fixing with, “L” type (125mmx125mm) 6mm thick and 25mm with MS clamps and connecting the length of PVC insulated wire and mending good damages to original finish and painting etc. by 2x24/0.20 mm (1.5sqmm.) flexible copper wire of 1.10 mt. length.

Extra for suspension exceeding 25 cm with S&F additional 2 no 20 mm dia EI conduit (14 SWG) supports & necy PVC insulated wire and painting etc as required by 2x24/0.20 mm (1.5sqmm) flexible copper wire of 1.10 mt length.

Supply and fixing of 220 Volts, 2A, B22 Batten Lamp Holder complete with brass screw on wall. [Make: Anchor/Goldmedal/Havells]

Supply and fixing of 9W LED B22 Bulb in existing holders [Make: Phillips/Magik/ Wipro]

Supplying & Fixing MS fan clam of two piece type for RC ceiling as per approved specification, fabricated from 40 mm x 9 mm MS flat including making good damages to building roof with satisfactory finishing and painting – (As per Drawing no. 475 of PWD Specification Book – May 1991)

Supply and delivery of 220V ,1200mm sweep 380 rpm ceiling fan with safety steel wire complete with all accessories (Canopy- 2 sets, shakle accessories, down rod, blades) without fan regulator. (Make:Crompton Rivera 1Star /equivalent Orient/equivalent Usha)

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire.

Supply & fixing of Exhaust fans complete with all accessories having the following Model/Cat No. (Make-EPC/CG/Havells) 9'', Speed 1370 RPM

Fixing only exhaust fan on wall by S&F rag bolts, nuts & washers (6 mm dia x 62 mm long) or as reqd. incl. S&F 24/0.20 PVC insulated flexible copper wire 0.5 mt. length 25 cm Exhaust fan (09")

Supply & Fixing louver shutter on wall with necy. bolts & nuts (6 mm dia x 62 mm long) 30 cm Exhaust fan (12")

Supply & Fixing Socket type fan regulator (Step type) (Brand approved by EIC) on existing sheet metal switch board with bakelite/perspex top cover by screw after making housing for regulator knob by cutting bakelite/perspex top cover incl. making necy. connections etc.

Supply & Fixing 240 V, 20A, plug socket with separate 20 A Piano key type switch (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F 150x100x 65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required

Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required [32 mm dia]

Supply and Fixing of 220V operated 100W ,IP-66 LED Flood Light with all necessary fixing arrangement. (Make: Philips/Wipro/Magik )

Supply & delivery of 250 V. 80 Wt., LED fittings complete with all accessories street light luminaire with single piece die cast alluminium housing and heat resistance toughened glass IP 66 protection out door luminaires) incl. fixing the fittings on the top of the pole as per direction of EIC. (Make: Phillips/Wipro/magik)

Fixing only outdoor / street light type fluorescent light fitting complete with all accessories to be fixed/projected from the wall of the building incl. making holes to building, S&F 40 mm dia GI pipe (ISI-Medium) 1.50 mts. average length, with GI socket at one end and thread at the other end & suitable bend to house the fitting & making necy. connections with S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall and painting

Supplying & Fixing PVC waterproof type looping cable box size 175x150x100 mm deep having 4 mm thick comprising of one 240V having lined with rubber gasketted PVC top cover with screws etc., incl. 4 nos. terminals for cable joint [Make: Sintex/ Hensel]

S&F timer for Compound light febricated with double door 8 Way SPNDB) i) 240 V,32A DP MCB of breaking capacity 10KA & ''C'' Charecteristic -1 No ii) 40A DP power contactor with 240 coil voltage -2 No. iii) Digital timer switch-1 No iv) Toggle switch -1 No. Make: Siemens/Schneider/GIC/Legrand/L-K

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level by ISI Medium GI pipe as to GS

Connecting the equipments body to earth busbar including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc.

Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages 4 SWG

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required.

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe

Supply and installtion of LED glow Sign board of 8 ft x 4 ft sizes signage made with 3 mm letter height 8-16", ACP duely moduled in 2'' raise with the help of 2 " x 1.5 " Alluminium/ GI rectangle hollow section frame and thus it became a ACP box where all the connection wire would be hidden inside it. back side covered by galvanised sheeet. 3" raised Acrylic letter made at 3 mm thick imported trans-light Acrylic sheet would be fitted with male female system where high luminated branded( Samsung) LED module pasted inside the 3D letter. SMPS for power supply would be fitted inside it. Fixing and fitting with 'L' type angle. ( Matter should be approved by EIC)

(Rate should be quotated including all taxes and duties and GST)

K.C. BYSACK AND SONS (BID ID -5567966)

ALPHA ELECTRICALS (BID ID -5587705)