SPECIAL REPAIR TO BUILDING NO P-5 AT AF STN DARBHANGA

Amount

Dismantling plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

S&F Pre- painted (Olive Green Colour) galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre- painted (Olive Green Colour) galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Demolition of Cement Concrete [Un-reinforced] in ground floors & paving not exceeding 15 cm thickness [below or above ground level] complete all as specified & directed.

M & L 40 mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in sub base, floor and paving finish surface even and smooth using extra cement complete all as specified & directed by Engineer-in-Charge.

S&F glass dividing strip 38mm wide and 3mm thick and inserted to certain design complete all as specified and as directed.

Taking down cement plaster on brick or stone surface of wall built in cement sand mortar including racking out joints, hacking for key, scrubbing down with water etc complete as specified & directed by Engineer-in-Charge.

M & L for rendering 15 mm thick on fair face of brick walls or concrete surface in CM 1:4 finished even and fair complete as specified & directed by Engineer-in-Charge.

M & L for rendering 10 mm thick on fair face of ceiling, soffit of chajja, fins etc in CM 1:6 finished even and fair complete as specified & directed by Engineer-in-Charge.

M & L preparation of new plastered surfaces on walls and applying two coats of oil bound distemper over a coat of chalk whitening primer complete all as specified and directed by Engineer-in-Charge.

M & L preparation of new plastered surfaces on walls and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

M & L preparation of new plastered surfaces on ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

M & L preparation of old plastered surfaces on wall and applying one coat of cement base paint complete all as specified and directed by Engineer-in-Charge.

M & L anodised aluminium snap grid frame work (size of grid 605mmx605mm) in false ceiling complete all as specified and directed by Engineer-in-Charge.

M & L 12mm thick perforated particle board/tiles for ceiling purpose of size 60x60cm fixed with screw complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc complete all as specified & directed.

M & L for brick work with subclass “B” Old size bricks, designation 75, straight or curved on plan exceeding 6 m mean radius built in cement sand mortar in 1:6 complete all as specified & directed.

Taking down chowkhat with shutter without taking off shutter from chowkhat area n exceeding 1.5 Sqm each complete all as specified & directed.

S & F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars,dovetailed or welded complete all as specified & directed.

S & F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars,dovetailed or welded complete all as specified & directed.

S & F steel ventilator with top hung shutters including peg stay , complete all as specified & directed.

S & F flat iron (mild steel) 12mm wide and 3mm thick fixed to steel window with screws or rebated for secure wire gauge , complete all as specified & directed.

S & F mild steel square bar in grill or guard bars welded to steel window , complete all as specified & directed.

S & F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples, beads complete as specified & directed by Engineer-in-Charge.

S & F sheet glass 3 mm thick ordinary quality in Square or rectangular in shape not exceeding 0.5 Sqm each pane and glazing with oil putty or steel pins complete all as specified & directed by Engineer-in-Charge.

M & L for preparation of new surfaces of steel and iron work of any description not otherwise described over 10cm width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed .

Taking down chowkhat with shutter without taking off shutter from chowkhat area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified & directed.

M & L 2nd Class hard wood Plain solid straight chowkhats and frame wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete as specified & directed by Engineer-in-Charge

S&F 35 mm thick factory made plain framed panelled door shutters with 2nd class hard wood rail and style with lock rails and with two panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneer on both faces; size of rails & styles as per IS: 1003 [Part I]; kiln seasoned and chemically pressure treated & fitted to chowkhats complete as specified & directed by Engineer-in-Charge.

S & F 35 mm thick 2nd class hard wood glazed and skelton door shutter, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for scuring glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified

M&L PCC 1:3:6 type C-1 using 20mm graded stone aggregate for fixing of hold fast etc complete as specified & directed.

S & F mild steel small items such as hold fast, strips for rain water pipes, bend stray support etc fixed with wall or otherwise specified complete all as specified and as directed.

S & F 300mm mild steel, ordinary rat tail rod double action pattern springs including roller and roller plate complete fixed to steel or wooden door frame including necessary welding cutting opening of wall for fixing brackets complete as specified & directed by Engineer-in-Charge.

S&F mild steel cold rolled butt hinges 100 mm medium weight fixed with screws to PVC or wooden frames or with welding in steel frame complete as specified & directed.

S & F 200mm long aluminium anodised,barrel tower bolts of extruded section complete all as specified & directed by Engineer-in-Charge.

S&F sliding door bolts clip type aluminium anodised with hasp & staple type, including bright bolts not less than 12mm dia with and including minimum 6 bolts & nuts, four on bolt plate and two on staple plate; length of bolts 300 mm long complete all as specified & directed by Engineer-in-Charge.

S&F extruded aluminium alloy handles anodised 150mm long fabricated type complete all as specified & directed.

M & L for preparation of new wooden surface exceeding 10 Cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer complete as specified & directed.

Dismantling timber scantlings framed work 40 sq. cm and over in section, in any position complete as specified & directed.

M&L for second class hard wood in scantling clean sawn and fixed in position complete as specified & directed.

M&L for second class hard wood plain fillets. square, rectangular or triangular in section, clean sawn, se-cured with nails or brads exc 13 and n exc 25 Sqcm complete as specified & directed.

M&L for preparing surfaces of wood and wood based materials,new or old, of any description and girth, not otherwise described and treated with Creosote complete as specified & directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding(but not backing), and rubbish off premises etc complete all as specified and directed.

M & L for 6 to 7 mm thick joint free non-skid ceramic coloured tiles ( square / rectangular) area of each tile not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:6 complete all as specified and directed.Make: Johnson/ Regency/ Somany/ Kajaria or Equivalent make as approved by Engineer-in-Charge

M&L Glazed ceramic coloured tile in vertical surface of size 350 mm x 450 x mm x 6-7mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment over & including bedding layer or screed bed in 10 mm thick cement sand mortar 1:4 complete as specified & directed by Engineer-in-Charge. Make: Johnson/ Regency/ Somany/ Kajaria or Equivalent make as approved by Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

M&L 15 mm thick rendering in cement sand mortar 1:4 with using water proofing compound on fair faces of brick work or concrete surface, surface to be finished even & smooth with out using extra cement complete all as specified & directed. Note: Water proofing Compound shall be measured and paid seperatly.

Supply only water proofing compound complete all as specified and directed.

M&L for applying evenly a tack/priming coat of industrial bitumen primer 85/25 as approved by Engr-in-Charge @ 1.2 Kg/Sqm over for use in damp proofing treatment on dried surface of concrete including cleaning surfacescomplete all as specified and directed.

Supply and laying , APP based polymeric membrane minimum weight 3Kg/Sqm and minimum 3mm thick reinforced with non woven fabric (weight not les than 150gm/Sqm laid on primed surface by force application etc complete all as specified and directed.

S & F PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and directed . Make : “SYNTEX/RAJSHREE Plastic wood Forex, Indore.”

S & F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR Part –I 2009 and as directed by Engineer-in-Charge Make : “SYNTEX/RAJSHREE

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Taking down steel water tubing and connections 15mm bore including cleaning for re-fixing or removal from site complete all as specified & directed by Engineer-in-Charge.

Taking down steel water tubing and connections 20mm bore including cleaning for re-fixing or removal from site complete all as specified & directed by Engineer-in-Charge.

Supply & fixing GI water tubing/pipe 15 mm bore medium grade with all fittings fixed to walls, ceilings and laid in floors complete all as specified & directed by Engineer-in-Charge.

Supply & fixing GI water tubing/pipe 20 mm bore medium grade with all fittings fixed to walls, ceilings and laid in floors complete all as specified & directed by Engineer-in-Charge.

Supply & fixing in position of Gun metal Gate or globe valve with iron wheel head, screwed both ends for iron pipes of size 20 mm bore complete all as specified & directed.

S&F in repairs Vitreous china squatting pan, orissa pattern, size 580x440 mm white, with integral foot rests including connection to trap and to flushing pipe, anti syphonage pipe including making good to floor with PCC 1:2:4 or cement sand mortar 1:3 complete all as specified and directed by Engr - in - charge. Make:- Hindware/Perryware/Cera

S&F PVC low level flushing cistern syphonic action type white with inlet ball valve, handle including brackets 10 ltrs capacity etc complete Make : Commander/Parrywre/ Hindustan or equivalent approved by Engineer-in-Charge.

S&F in repair vitreous china wash hand basin white flat back of size 550mm x 400mm including bracket with 32mm PVC waste down pipe complete Make : Hindustan/Cera/Nycer/parryware or equivalent approved by Engineer-in-Charge

S/F in repairs chromium plated cast copper alloy bib taps 15 mm bore fancy type capstan head handles half turn or full turn compete all as specified and directed.

S/F in repairs Stop valves/concelled stop valves/angle cock, 15mm bore cast copper alloy, fancy type CP screwed down high pressure screwed both ends for iron pipes or for unions compete all as specified and directed.

S/F in repairs Pillar taps, 15mm bore CP with capstan heads, long body screwed down, screwed for lron pipe high pressure with lettered "hot or Cold" with long shank compete all as specified and directed.

S & F in PVC connections 15mm size with PTMT nuts and bolts of length 450mm etc complete all as specified and directed

S&F PVC [SWR] bends with access door, any radius of 110mm bore complete all as specified & directed.

S&F PVC [SWR] junction single (single T) equal or unequal with access door, any radius of 110mm bore complete all as specified & directed.

S&F PVC (SWR) pipe single socketed with rubber ring joints 110mm bore laid in trenches or in floor etc complete all as specified and directed

S&F in repair CP brass shower rose with or without swivel joints 125mm size including fixing to steel pipe or union complete all as specified and directed.

S&F brass chromium plated towel rail 600 mm long and 20mm dia D type fixed with CP screw & wooden/plastic cleats etc all as specified and directed by engr-in-charge.

Taking down carefully unserviceable aluminium point wiring (light, fan, socket or power) complete with fitting such as switches, ceiling roses, lamp holders, sockets, fan regulators, wooden terminal box plastic laminated sheet cover from TW battens including TW batten or drawing from existing conduit removing including TW batten all as specified and as directed by Engr-in-Charge.

M&L for point wiring for one light/fan/bell point control by one switch with single core PVC insulated unsheathed 1100 volt grade FRLS wiring cable IS:694 cable with multi stranded copper conductor of size 1.5 sqmm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20 mm dia, fixed (concealed conduit wiring) on wall and on ceiling with GI saddles, GI screws, rowel plugs (surface conduit wiring) with all fittings including tee, junction boxes and provision of pressed steel terminal box 1.25 mm thick of suitable size with 3 mm thick plastic laminated sheet cover for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC insulated unsheathed 1100 volts grade cable with multi stranded copper conductor of size 1.5 sqmm (Nominal area) connected to earth dolly complete all as specified and as directed by Engr-in-Charge. Make of Cable will be Havells/Plaza/Polycab/Kalinga/Anchor/KEI and make of PVC conduit will be Plaza/AKG/Kalinga/Jindal

All as per item No 73 above for 5 pin 6 amps socket outlet on independent board controlled by one switch complete all as specified and as directed by Engr-in-Charge

All as per item No 73 above for 5 pin 6 amps socket outlet on same board controlled by one switch complete all as specified and as directed by Engr-in-Charge

All as per item No 73 above for one power point 3 pin 16 amps socket outlet on idependent board with FRLS PVC insulated unsheathed 1100 volt grade cable with multi stranded copper conductor of size 2.5 sqmm (Nominal area) including provision of earth wire FRLS PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 2.5 sqmm (Nominal area) cable common connected to earth dolly all as specified for one 3 pin 16 amps socket outlet controlled by one switch complete all as specified and as directed by Engr-in-Charge.

S&F switch piano flush type 5 amps single pole one way complete for one light/fan point controlled by one switch all as specified and directed by Engr-in-Charge. Make : Anchor/Havells/Leader

S&F socket out let 5 pin, 6 amps flush type complete all as specified and directed by Engr-in-Charge. Make : Anchor/Havells/Leader

S&F switch socket outlet, multipurposes 2 in 1, 3 pin 6/16 amps flush type complete all as specified and as directed by Engr-in-Charge Make : Anchor/Havells/Leader

S&F of ceiling rose surface type 65 mm x 50 mm, 2 to 3 terminal complete all as specified and as directed by Engr-in-Charge. Make : Anchor/Havells/Leader

S&F stepped electronic type fan regulator 100 watts, 230 volts, 50 Hz, AC supply complete all as specified and as directed by Engr-in-Charge. Make Anchor/Havells/Leader

Taking down old unserviceable main switch/DBs/MCB DB with MCB and making good complete all as specified and as directed.

S& F MCB distribution board TPN 4 way double door, sheet steel, phospetised, powder paited with 200Amps rated bus bar, 240 volts with all connection complete all as specified and as directed by Engr-in Charge.Make: Havells/Schneider/legrand/L&T

S&F MCB TPN 3 pole 63 amps, 50HZ, 415V with rupturing capacity 25KA complete all as specified and directed by Engr-in-Charge. Make : Havells/Schneider/legrand

S& F MCB distribution board SPN 8 way double door, sheet steel, phospetised, powder paited with 200Amps rated bus bar, 240 volts with all connection complete all as specified and as directed by Engr-in Charge.Make: Havells/Schneider/legrand/L&T

S&F MCB SPN 32 to 60 amps, 240V with rupturing capacity 10KA complete all as specified and directed by Engr-in-Charge. Make : Havells/Schneider/legrand

S&F MCB SP 6 to 20 amps, 240V complete all as specified and directed by Engr-in-Charge. Make : Havells/Schneider/legrand

Taking down old unserviceable light fittings of any type complete all as specified and directed by Engr-in-Charge.

S&F LED tube light fittings, MAXOLED BATTEN- for T8 LED Retro Lamp with bipin holder, connector block with tube rod Maxoled (tube) 20W LED tube with single side etc complete with all accessories pre-wired twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. Make : Havells/Bajaj/Phillips.

S&F Lamp holder with LED lamp 10watts, PVC/ polycarbonate batten type with cord grip cap suitable for pendent/angle type complete all as specified and as directed by Engr-in-Charge. Make :Bajaj/Havells/Phillips

S&F security light fittings LED type complete with perspex cover, reflector, chock, starter, bi-pin holders etc for 40 watt LED complete all as specified and directed by Engr-in-Charge. Make : Havells/Schneider/legrand

Taking down fan of any make, type and sweep, ceiling cable end, dismantling blades and removing fan and depositingto store complete all as specified and directed by Engr-in-Charge.

Hanging only ceiling fan /exhaust fan 230V, 1200/1400mm sweep with complete accessories complete all as specified and directed by Engr-in-Charge.

S&F in replacement of unserviceable sub main wiring with two single core PVC FRLS IS-694 cable with copper conductor of size 4 sqmm and drawing through non metallic rigid PVC conduit (concealed conduit) including 2.5 sqmm FRLS PVC insulated unsheathed stranded copper conductor cable as medium grade earth conductor connected to earth and earth dolly in conduit including connecting to main board including non metallic PVC conduit medium grade of 25 mm dia size with all accessories complete all as specified and as directed by Engr-in-Charge. Note : two run for 4 sqmm and one run for2.5 sqmm will be measured as one RM.Make of Cable will be Havells/Plaza/Polycab/Kalinga/Anchor/KEI and make of PVC conduit will be Plaza/AKG/Kalinga/Jindal

Supply and laying XLPE insulated screened PVC bedded cable, galvanized steel strip or wire armored, electric power cables (heavy duty) 11000(E) Volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 core including taking down old unserviceable cabe of any size complete all as specified and directed by Engr-in-Charge. Make : Havells/Fort Gloster/Asian cables/Polycab/Universal.

Excavating in trenches, not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for wall foundation, cable trenches etc or for manholes etc not exceeding 10 Sqm area on plan and getting out in soft/loose soil complete all as speified and as directed.

Supply and lay sand cushioning in trenches with clean dry unsheathed gently punning around cable for protection complete. Note : Only punned thickness shall be measured for payment

M&L well burnt sub class 'B' bricks laid flat width wise along the length of cable for cable protection complete all as specified and directed.

Returning filling in foundation/trenches including spreading leveling, watering and well ramming in layers not exceeding 25cm thick in any type of soil complete all as speified and as directed.

Removing excavated surplus soil to a distance n. exc 50 metre and deposited where directed at a level n.exc 1.5 metre above the starting point complete all as speified and as directed.

S & F 50mm dia GI tubing light grade, on poles, under floors, road crossing etc includng all fittings as in cable protection complete all as specified and as directed by Engr-in-Charge.

M&L for earthing complete with galvanized steel earth plate 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanized earth lead wire 4mm dia as earthing lead by means of bolts, nuts, check-nuts, and washers of galvanised iron or steel besides welding at all joints as shown in drawings and including excavation and earth work, GI pipe light grade 40 mm bore for protection of GI strip from earth electrode to and including the earth test point of galvanised iron/steel. supplying and laying charcoal stone aggregate) chamber and RCC cover of size 54x54x50mm (1:2:4) type B1 using 20mm graded crushed stone aggregate reinforced with 8mm dia TMT bars @ 75mm C/C both ways with mild steel handle 12mm dia, PGI funnel with wire mesh, 20mm dia GI pipe medium grade for watering all as shown in drawing including taking out the old one. Note : Cost of GI wire and GI protection pipe upto a distance 7.5M shall be included in quoted rate of above items.

Prabir Kumar Dasgupta

PAPPU ROY CONSTRUCTION

JAI MATA DI CONSTRUCTION

M/S NARAYAN ENTERPRISE