E1-1251-2022-ERODE CITY MUNICIPAL CORPORATION-PROVIDING ADDITIONAL IMPROVEMENT WORKS AT SOLAR NEW BUS STAND S.F. NO. 11-2 IN ERODE CITY MUNICIPAL CORPORATION

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete

Hard rock measured in solid including blasting and stacking - complete complying with standard specification and as directed by the departmental officers - TWAD item 20(a)

Plain Cement Concrete 1:4:8 (one cement four M Sand and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification.

Brick work in CM 1:5 (one cement & five sand) using II class ground moulded bricks of size 9"X43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification.

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed - 10 m 2 (P & D)Data 38

A)Strom Water drain

B) Shear Wall

C) Beams & Flat Surface

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS staandards. (No separate payment will be made by the Department for the excess usage of materials)

Strom Water Drain

Plain Cement Concrete 1:2:4 (one cement, two Crushed Stone Sand (M- Sand) and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Supplying, fabricating and placing in position of Steel reinforcement using MS (or) RTS rods for all RCC item of works including cost of steel and binding wire in all floors etc., complete complying with standard specification and as directed by the departmental officers.

Plastering with cement mortar (1:5) 12mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Painting Two coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Dadooing walls with Glazed tiles of sizes 300 x 450 x 8mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement as per std specification .

Paving the floor with fully polished Rajasthan Kotta stone of size 610mm X 610mm and 20mm thick (average) and base layer of cement mortar 1:3 (One cement and three sand), 20mm thick and applying cement slurry & pointed with white cement and colour pigments to the colour of stones and polished neatly etc., complete complying with standard specification and as directed by the Departmental officers. (The Kotta stone slab should be got approved by the Executive Engineer before use on works)

Supplying and laying in flooring with fully polished colour Granite stone of 20mm thick (average) of 4' X 2' in size laid over base layer of cementmortar 1:3 (one cement and three m-sand) - 20 mm thick and applying cement slurry & pointed with white cement and colour pigments to the colour of stones and polished neatly as directed by the deparmental officers

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification.

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Providing and fixing SS Hand Rail made out of SS 304 grade 50.80mm dia stainless steel tube of 1.60mm thick will be provided with tubular supports made of SS304 grade stainless steel tubes 0f 25.4mm dia welded to the railing. The supports will be grouted and provided with a 3.00mm thick circular base plate of SS 304 grade stainless steel as per the details shown in the drawing and as directed. The rate shall include for grouting with concrete in to necessary supporting arrangements of handrail in floor, welding the base cup of the post onto slab reinforcement, polishing, buffing and protecting the handrail surface etc., complete as directed by the departmental officers etc.,

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work sqm.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Fabricating supplying and fixing of Polycarbonate Sheet with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers. Morth - Rev V No. 111,112,401,900

Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Providing and laying Prime coat of 7 kgs/10 sqm over the WMM surface treated with primer using 7 kgs of bituminous Emulsion for 10 square meter area including cost of bituminous binder, including labour charges for applying the required quantity of bituminous binder as Prime coat manually etc., complete as per 502 of MORTH Rev V Specifications.

Providing and laying tack coat of 2.5 kgs/10 sqm over the WMM/ surface treated with binder using 2.5 kgs of bituminous Emulsion for 10 square meter area including cost of bituminous binder, including labour charges for applying the required quantity of bituminous binder as tack coat manually etc., complete as per 503 of MORTH Specifications .

Providing and laying 50mm consolidated thick Dense Bituminous Macadam using 0.24cum of 26.50-13.20mm, 0.25 cum of 13.20-2.36mm and 0.23 cum of 2.36mm & below and with 53.20Kgs of VG30/VG40 bitumen for premixing per 10sqm including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing the min. required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to worksite, spreading the mix to uniform thickness of 50mm with paver to the specified grades and cross sections and compacted by Vibratory / Pneumatic Roller to the required density etc., including labour for attending to paver at site etc., including hire charges and fuel charges for 20- 30t CMP with bitumen boiler, tipper trucks, Paver Finisher /9m paver finisher, Vibratory / Pneumatic rollers and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 505 MORTH Rev-5 Specification

Providing and laying Bituminous Concrete to 40mm thick using 0.13 cum of 19.00 - 9.50mm, 0.17cum of 9.50 -2.36mm and 0.26cum of 2.36 and below with 45.27kgs of VG30 / VG40 bitumen including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing the min required temperature in central hot mix plant 20-30ton capacity, conveying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 30mm with mechanical paver to the specified grades and cross sections and consolidated by 8-10tonne Vibratory / Pneumatic Roller to the required density etc., including labour for attending to paver to site etc., including hire charges and fuel charges for 20-30t CMP with bitumen boiler, tipper trucks, Paver Finisher / 9m paver finisher, Vibratory / Pneumatic roller and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 507 of MORTH Rev-5.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC light point / fan point (for electronic regulator) SD 16

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) (SD 144)

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable heavy gauge PVC conduit pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 55)

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable heavy gauge PVC conduit pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion wiith suitable colour (SD 57)

Supply and run of 3 of 4 sq.mm. (56 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable heavy gauge PVC conduit pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 48)

Supply and fixing of 4way SP DB of 16A / way with 16A DP switch with metal gland of 500V (side handle) with fuse and neutral on suitable angle iron frame work with trunking box MS cable entry box with earth connection (SD 148)

Supply and fixing of 8 way SP DB of 16A / way with 16A DP switch with metal clad of 500V with fuse and neutral (side handle) on suitable TW board with PWD earthing (SD 151)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End (SD-518)

Supply and laying of 2 x 6 sq.mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of M.Sand and covering the cable completely with bricks and sand and refilling the earth to make good (SD 197)

Supply and laying of 2 x 6 sq.mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (Same as per SD 184), except for 3-1/2 x 70 sq.mm. PVC LTUG aluminium armoured cable (SD 185)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 211)

Supply and Fixing of LED Flood Light 100W with Integrated Driver including all cost of labour and material charges.

Supply and fixing of fancy glass shade and 15 W Tube Iight (SD 80)

Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb (SD 83)

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18") (SD 106)

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall (SD 114)

Supply and fixing of TNEB meter board suitable for 32Asingle phase service connection with 32Afuseunit (500V)32A neutral link and earth link(1"x1/8"copperflat) on TW plank of size375mmx300mmx19mm with supporting TW reepers of 1"thick aneither side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection andinter connection with 7/20 PVC insulated copper wire from EB metert of use unit with 0Amp 30 MA Double Pole RCD / RCCB (Higher End) with suitable necessary connection1No (SD 125)

Supply and fixing of TNEB meter board suitable for32A Three phase service connection with 32Afuseunit (500V)32A neutral link and earth link(1"x1/8"copperflat) on TW plank of size375mmx300mmx19mm with supporting TW reepers of 1"thick aneither side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection andinter connection with 7/20 PVC insulated copper wire from EB metert of use unit with 1No

Supply and fixing of 3 Phase 4 Way ICDB 32 A Per Way 100 A TPNMC Switch with trunking box MS cable entry box with earth connection (SD 178)

Supply and fixing of Cable Gland For 2 x 6 sqmm Pvc LTUG armoured cablecable with earth connection (SD 159)

Supplying and fixing in position SFCR Manhole covers (light or heavy duty) of Size 600mmx600mm of best approved quality and as per atandard specifications etc.,complete.

Supply and fixing of CP Two Way Bib Cock with Health Faucet cost of all materials and ISI mark including labour for fixing charges etc., complete

Health Facut

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with 1000 lit

Supply and fixing of Generators with auto main failure (AMF Panel) - 250 KVA including all charges, cost and conveyance of all materials to site, etc. complete as per standard specification (ER - page 44)

Supply, erection testing and commissioning of 250KVA/ 11KV / 433V copper wounded OFF LOAD TAP changing outdoor type distribution Transformer conforming to relevant IS 1180- Level 2 and fitted with the following. Including transformer plinth with brick / (concerting) of size 6’ x 6’ x 4’a) LT cable end box suitable for connection 3run of 3½ x 400sqmm LTUG cable & HT Bushing. b) Conservator with shunt off valve. c) Dehydrating silica gel breather. d) Conservator drain plug valve. e) Tank drain plug valve .f) 4nos. plain rollers .g) Thermometer pocket with thermometer with capillary tubing for maximum reading position.)h) Drain plug valve. i) Filter valve j) Oil filling hole end cap. k) Oil level gauge M) Rating and terminal marking diagram plate. n) Lifting hooks / lifting eyes / jacking pad facilities movement to transformer and easy ground level. o) Marshalling box. p) Neutral on LV side to be availed for 4wire supply and brought out through bushing for earthing . All removal covers shall be provided with weather proof hot oil resistant, resistance gaskets to prevent leakage of water in to core, and oil from the tank with low no load loss and full load loss, impedance. (Make: Indotech (Porlec-GE) / Kirlosker) / ABB /CREL. The transformer should get prior approval from Engineers.

11 KV 2 pole HT Structure

Supply and erectoin of 250 Amps capacity floor mounting type metering panel board (cubical type) with bus bar chamber made up of CRCA Sheet for 3 phase 4 wire system with 40mm x 10mm tk coated copper flats for phases and neutral; cable chamber, switch chamber and with 2 nos. 25mm x 3mm tk copper flats for the earth bus on the rear side of the panel board; necessary interconnections by copper flat of suitable sizes; suitable PVC colour sleeves for the interconnecting copper flat/ rigid copper wire; earth connections to all switches/ bus bar by copper flats of suitable sizes from the earth bus; hylem sheet seperation between bus bar and switches ; 3 nos of LED pilot lamps with switches, fuse units, suitable angle iron frame size of 38mm x 6mm with powder coated painting over one coat of red oxide and with numbering; supersciption of cables sizes, capacity of switches etc., and incorporating the following: OUTGOINGS: SINGLE PHASE SERVICES 35 Nos 32A DP MCB/40A 10 KA DP MCB 35 Nos. 32A Fuse Units, 25mm x 3mm x15mm copper flats for neutral and earth space provision for TNEB Energy meter with glass cover BUS CAPACITY: A 3 Phase 4 wire copper 2 nos dummy provision internal connections by 2 runs of 4 sq.mm PVC insulator unsheated copper conductor of 1100 V grade from TNEB Cut out to the meter and from the meter to the 32 A DP MC Switch /32 A KA DP MCB 3 Nos of LED Pilot lamps with fuse units, switches/and interconnections; inter connection to the bus bar by 25mm x 3mm TC Copper flats for phases and neutral from 125 A TPN SDF to the bus; interconnection by NO.8 SWG Copper for the phases and neutral from the 32A 10 KA DP MCB Switch to the bus; 6mm tk hylem sheet seperation between bus bar chamber and switches chamber; insulaters for the support for the bus; superscribing on the panel board the size, capacity of cable, switches, location etc., 2 nos metalic danger boards.

Supply and laying 31/2x150 sq.mm PVC LTUG armoured cable in a trench to be excavated at a depth of 0.75 m putting 0.15 mtr layer of snad and coveing the cable completely with bricks and sand and refilling earth to make good (make:ISI quality only)

Supply and fixing of brass cable gland for 3½ x 150 Sq.mm PVC armoured LTUG cable and providing cable end termination with necessary aluminium cable sockets by crimping etc with electrical connection complete.(make:ISI quality only)

Supply and laying 31/2x70 sq.mm PVC LTUG armoured cable in a trench to be excavated at a depth of 0.75 m putting 0.15 mtr layer of snad and coveing the cable completely with bricks and sand and refilling earth to make good (make:ISI quality only)

Supply and fixing of brass cable gland for 3½ x 70 Sq.mm PVC armoured LTUG cable and providing cable end termination with necessary aluminium cable sockets by crimping etc with electrical connection complete.(make:ISI quality only) (SD-189)

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection and connect earth pit to DB, etc.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of M. Sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100mm 'P' os 'S'' trap with Double flapped rigit P.V.C. seat cover with C.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings etc., complete complying with standard spoecifications,labor inclusive of fixing lowlevel flushing tank.

S/F in position of Indian Make White/Colour glazed earthen ware lipped mouth Flat Back Urinal of best approved quality with G.I.Pipe connection to suitable length,32mm bell mouthed P.V.C connection ,15mm dia G.M.Wheel valve,fixing the urinal to the wall in position with necessary T.W.plugs ,clamps,screws, shellac etc.,including dismantling masonry if necessary and redoing the same to original condition ,fixing the 15mm dia. G.I.pipe connection and wheel valve ,painting the pipe with two coats of approved paint over one coat of primer and checked without any leakage complete, complying with standard specifications. - White Colour

Internal Water Supply - P.V.C. Pipes (6Kg/SqCm) Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

c)40mm dia pipe in toilet inner

d) 50mm dia pipe in toilet inner

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings - 100 mm x 75 mm including all charges etc, complete as per standard specification.

Suppling and fixing in position 15mm.diameter brass / C.P screw down tap of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary

Supplying and fixing in position P.V.C. specials such as plain bend, door bend, plain tee, door tee, offsets,Y-junction, plain or with door of various sizes best quality confirming to I.S.S and providing leakproof joints including fixing to wall and giving connection to the P.V.C, soil stacks, dismadling the brick masonry or R.C.C. floor or Roof slab and redoing the dismandled portion to original condition etc., complete complying with standard specifications.

160mm PVC Shoe

150mm PVC Elbow

160mm PVC Y

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

a) PVC Soil pipeline 110mm dia

Supplying of RCC non pressure spun pipe with socket and spigot ends as per IS 458/2003 manufactured with sulphate resistant cement with 12 mm HI -alumina lining with rubber ring joints.NP2 Pipe-450mm

Lowering RCC pipes and specials into the renches and laying to proper grade and alignment-NP2 Pipe-450mm

Jointing RCC pipes with cement using necessary collars including the cost of jointing materials. -NP2 Pipe-450mm

Supply, erection, testing and commissioning of Fire Fighting Application Horizontal Centrifugal Type Pump Rated for 2280 LPM at 70 metres head with Electrical Motor of 60 HP of 415 volt 3 phase connection complete with base plate and accessories. (Make: Kirloskar or Equivalent). The rate inclusive of necessary vibration, bad mounting etc., as per standard method as directed by the Deparmental Officers

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following and complete in all respects as required. a. End suction, top discharge centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg. / sq. cm at highest and farthest outlet at specified flow of 2280 LPM at 70m head conforming to IS 1520. b. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dyanamo, solenoid switches etc. c. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc. (Make: Kirloskar / Equivalent). d. Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m, outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessory MS support arrangements from wall or ceiling as per site condition.e. Dash board consisting the instruments like temperature gauge, galvano type DC Ammeter, lubricant oil pressure gauge, ignition switch, emergency stop and all other protection equipment as per specification, stop seleneid for auto stop in the event of fault with audio indications, painted with post office red colour etc., as required. f. 12 V / 24 V storage battery, maintenance free tape, 180 AH rating, MS fabricated common base plate, coupling guard, foundation bolts etc., as required. g. Positioning the diesel engine driven fire pump over cement concrete foundation using suitable size anti-vibration mounting arrangement. All works carried out as per standard methods and as instructed by the manufacturer and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply, erection, testing and commissioning Mono Block type Fire Fighting Pressurisation Pump of 180 LPM 110 metres head at 10 HP with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply and laying of following sizes of Armoured Aluminium Cables for electrical motor, control panel, pressure switch, jockey motor etc.. The rate inclusive of all incidental charges, neccessary scaffolding and redoing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT.

3 core 95 sq.mm. armoured aluminium cable

3 core 10 sq.mm. armoured aluminium cable

10 core 2.5 sq.mm. armoured aluminium cable

Supply and laying of 2 core 1.5 sq.mm. armoured copper cable for control wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.

Supply,installing Cable tray with necessary angle iron suspension supports, anchor fasteners etc. complete. Maximum height of suspension GI Hot Dip / Powder Coated 16 SWG Cable Tray with 150mm width and 50mm height . Size of the tray shall be suitable for laying the above mentioned cables.

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table „E‟, gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

Supply, erection, testing and commissioning of Gun Metal Gate Valve of size 50mm dia size including necessary MS flange of table „E‟, gaskets, bolts & nuts etc., installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.

Supply, erection, testing and commissioning of Gun Metal Ball Valve of size 25mm dia size including necessary Fittings and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Nonreturn valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table „E‟, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers

Supply, erection, testing and commissioning of following sizes of Heavy Duty Foot Valve including all accesories, such as, MS flange of table „E‟, gaskets, bolts & nuts, etc., installed at end of 150 / 200mm dia suction pipe line at sump including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete and as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

150 mm dia

100 mm dia

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification.100mm

Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply of Fire Fighting Application MS Cabinet Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT

Supply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 900 LPM at 40 metres head to develop 3.5 kg/sq.cm at the heightest and farthest hydrant point to make 30 m water jet at the time of fire fighting emergency cicumstances, coupled with 11 KW / 15 HP rated three phase 414 volts, 50 Hz, 2880 rpm electrical motor the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia., including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers (Kirloskar make KDS 1555+ or Equivalent)

Supply and laying of 4 core 10 sq.mm. armoured copper cable for power wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Supply, erection, testing and commissioning of FM / UL approved Metallic stainless steel (SS 304) braided Flexible drop pipes of 25mm Dia with cross bar assembly support suitable for grid ceiling, reducing fitting, special shoulder Nipple, reducing nipple, T bar bracket, bracket clip assembly. Flexible length shall be as below 1500mm

Supplying and installing of approved type Rosette Plates (Recessed Type in Two Pieces) for sprinklers below false ceiling area. The Rosette shall be fabricated by MS plate of 2mm thick and the finish shall be powder coated and colour, as directed by the Departmental Officers.

Supply, installation, testing and commissioning of Micro Processor based conventional 12 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers

Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (Make: Apollo / Equivalent)

Supply, installation, testing and commissioning of Conventional Heat Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (Make: Apollo / Equivalent)

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent)

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of Carbon-di-Oxide Gas Type 2Kg Capacity Fire Extinguihsers as per IS:15683 with , discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supplying, installing, testing and commissioning of 6W Wall Mount type speakers

Supplying, installing, testing and commissioning of solid state Amplifier of 250W RMS out put in rack, including necessory control wires, jacks etc. complete.

Supplying, installing, testing and commissioning of Hand Held Mic with Frequency response-40-16000 Hz,Secsitivity - 1,8 mv/Pa,Connector XLR-3 including all Charges

Supply & Installation of in position the sign board of "EXIT " with arraow to be placed at walking pathways by fixing on walls to direct occupants to outside the buliding in an emergency. The Exit sign board will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Supply & Installation of Fire Escape Route Plan Laminated Board Auto Glow Print to be placed at each floor by fixing on walls to direct occupants to outside the buliding in an emergency. The Fire Escape Route Plan will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Supply and Installation of IP based Surveillance camera at the Following specification 2.0 MP CMOS Network Bullet Camera 1 /2.8” Progressive Scan, Upto 2.0 Megapixel, 2.8mm/4mm/6mm Fixed Lens, Upto 80 Meters IR Range, Dual Stream, Digital WDR, 3D DNR, PoE Support, IP 67, Mobile Monitoring, Video Bit Rate : 32 Kbps to 8 Mbps, NAS (NFS, SMB/CIFS), Motion Detection, Alarms for Video Detection, Network Disconnection, IP Address Conflict, TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, NTP, RTCP, UPnP, SMTP, IGMP, 802.1X, QoS, IPv6, Bonjour, ONVIF (Profile S, Profile G), PSIA, CGI, ISAPI, 1x 10/100 Mbps RJ 45, -30°C to 60°C, 12V DC, Maximum 5Watts Power Consumption etc complete .,

Supply and Installation and Fixing of 8 Channel NVR ( Network Video Recorder ) With 1 Sata H.265+/H.265/H.264/H.264+ Video Formats, Third Party Network, Upto 8MP, Incoming Bandwidth 80 Mbps, Outgoing Bandwidth 80 Mbps, TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP, HTTPS, Upto 6TB, 2xUSB2.0, 12V DC, 18 Watts Power Consumption, -10°C to 55°C, 1U Chassis Recording Resolution - 8 MP/6 MP/5 MP/4 MP/3 MP/1080p/UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF, Network Video Input -32 Channel, Audio Output- 1 ch, RCA(Linear,1K Ω), Max. Capacity -Upto 10TB capacity for each Hard disk, Video output-HDMI Video Output upto 4K(3840*2160),VGA Output, Live View/Playback Resolution - 8 MP/6 MP/5 MP/4 MP/3 P/1080p/UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF etc complete

Supply and Installation of 4TB Surveillance Hard Discof approved Make - at the following Specification 1) Camera supported- Up to 64, 2)Load/unload Cycles- 3,00,000,3)Cache (MB) - 64, 4)Mean Time between Failures (MTBF) (hours)-1M, 5)Max sustained data rate,OD read(MB/s)-190, 6)Voltage tolerance(5V)-5%,7) Voltage tolerance(12V) -10% , 8)Start-up power (A)-2, 9)Operating mode,typical(W)-5.5, 10) Idling average(W)-3.2, 11) Standby mode(W) - 0.25/0.25 and 12) Storage capacity -30 days etc Complete

Supply and Installation and Fixing of 4, 8 Port Fully PoE Switch (Power Over Ethernet Switch) Ethernet Ports One (1) 10/100/1000 Base-T Port One (1) 1000 Base-X Port Eight (8) 10/100 Base-T Ports (PoE Power Supply) PoE Features • Protocol: IEEE802.af, IEEE802.3at, Ports 1 to 8 • Consumption: Up to 30 W per Port • Total PoE Budget¹: 196 W Switching Capacity 7.6 Gbps Packet Forwarding Rate 4.17 Mbps Packet Buffer Memory 1 MB MAC Table Size 8K Flow Control Enable by default Power Requirements 53 VDC Power Adapter (included) Operating Temperature -30 °C to 65 °C (-22 °F to 149 °F) Application Humidity 10% to 90% Lightning Protection Common Mode: 2 KV Differential Mode: 1 KV Dimensions (W x D x H) 150.0 mm x 100.0 mm x 42.0 mm

HIKVISION POE 4+2 Port Gigabite 2 year Warrenty

HIKVISION POE 8+2 Port Gigabite 2 year Warrenty

Supply and Fixing Cat6 - Patch Card including cost and Conveyance, Labour Charges For Cable laying etc., complete

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade on 7/20 GI bearer wire for service connection mains SD 64

Supply and fixing of 5A 3 pin and 2 pin combined flush type wall socket with 5A flush type switch on suitable TW box SD 136

Charges for Camera Device Configuration, Instalation & Positioning etc complete .,

Charges for Rack Fixing & Alignment etc complete .,

DCM box

Supply and fixing of 3 Seater Stainless Steel Waiting Chair including all labour charges etc

3 Seater Stainless Steel Waiting Chair

Supply and Fixing of Shops Numer Board of 20CM dia Size / Names Board Bard of 40CM x10CM Size Like Lift , Toilts etc using 6mm thick Agarlic Sheet and writter leeter to blue colour stricker over the agarlic sheet including cost of all labour charges to fixing infront of shops and toilet s etc complete

a) Shops Number Plate -20CM Dia

b) Busbay Agralic Name board

Supplying and fixiing of Aluminium Dye cast Letter of approved size and color. The Colour treatment process is achieved with MRF Colour Coat and them the Processed coloured layer is set into the kiln for the heat treatment process for the following size

Alumium Dye Cast Letters 9" Size

GMS Elegant Builders I Pvt Ltd (BID ID -1363269)