Reinvited for Repair of corridors of ward nos. 1 2 3 4 5 6 7 8 9 10 14 and 15 ground floor 1st and 2nd floor in University of Health Sciences Rohtak

Amount

Dismantling cement conglomerate/ terrrazzo-floors 25 mm to 50mm thick without concrete base (HSR 8.26)

Conglomerate floor 40mm thick cement concrete 1:2:4 on 100mm cement concrete 1:8:16 and 100mm sand or stone filling. (HSR 14.12)

Fixing marble stone flooring 17mm and above thick slab including matching grains of marble laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment ot match the shade of marble including rubbing and polishing (Excluding the cost of marble.) (HSR 14.49) (a) White marble (i) White Makana marble (1st quality)

Kotah stone flooring minimum 25mm thick, in any pattern as specified over 20 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing.( HSR 14.62)

Kotah stone 20mm thick in skirting risers of steps, dados and wall facing ( Lining) and pillars laid on 12mm thick cement coarse sand plaster 1:3 laid and jointed with neat cement slurry, mixed with pigment to match the sande of stone including labour for fixing cramps, dowels and pins etc.(HSR 14.66)

Laying and fixing vitrified/ceramic/glazed tiles of any size of approved make in skirting/dado, pillars, wall facing, laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (Tiles shall be supplied by the Department). (HSR 14.94)

Laying and fixing granite stone in all shades, 15mm to 18mm thick in skirting/dado, risers of steps, pillers and wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite including labour for fixing cramps pins and dowels etc. (excluding the cost of granite stone) (HSR 14.95)

15m thick cement plaster 1:4 on the rough side of single or half brick wall ( HSR 15.10).

Wire gauze fixed on chowkats with 25mm thick cover moulding of full width of commercial hard wood such as hollock, champ chikrassy and chaplash, etc., (Non-coniferous timber, other than teak, conforming to I.S. specification No. 1003, kiln seasoned). (HSR 17.33)

Supplying and fixing glass panes with moulding of commercial hard wood such as hollock, champ, Chikrassy and Chaplash etc. (non coniferous timber other than teak, confirming to IS specification No. 1003, kiln seasoned) (c) 4 mm thick (glazing area above 55 sq dm but upto 84 sq dm of each pane) (HSR 17.36 c)

Factory manufactured solid flush door shutters, with block board core as per I.S. No. 1659-1669 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I. and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above, but including labour for fixing the same in position) (HSR 17.93)- Note 1 under chapter 17.18) (a) Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges:-(Jwala/Ujala make).

(iii) 35 mm thick

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to I.S.733 and I.S. 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasterners including necessary filling up of gaps at junction, at top, bottom and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing/panclling C.P. brass/stainless steel screws, all complete. Fixed portion (Anodised aluminium transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15)(HSR 17.95)

Wrought iron and mild steel (using angles, flats, square bars, tee and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed staircase or parapet or any other type of railing, gates and tree guard etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12)

Pressed steel sheet frames (chowkats) consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts) iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead Non-setting primer,of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete :- (HSR 18.34 ) (a) Door and window frame of size 89 mm x 50 mm with 40 mm wide single rebate

N.S ITEM

Laying 30mm (avg.) thick cement plaster mixed with coarse sand with bonding agent chemical (Epoxy grouting) under side of ceiling (N.S.)