REPAIRS TO FLOOR, WALL TILING, PLUMBING WORK AND CERTAIN MISC B/R AND COMPREHENSIVE REPAIR TO E/M WORKS IN OTM AND MD ACCN UNDER WEST ZONE OF GE (NORTH) AKHNOOOR

Amount

Sunken Floor treatment :- Taking down old treatment/ floor tiles/ PCC and Providing & laying of water proofing treatment to sunken portion including vertical portion by applying cement slurry mixed with acralic based polymer modified cementitious composite compound of make as approved including demolition and filling of sunken floor. (a) First layer of slurry of cement @ 0.488 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @0.253 Kg/Sqm. This layer allowed to air cure for 4 Hours. (b) Second layer of slurry of cement @ 0.242 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.125 Kg/ Sqm his layer allowed to air cure for 4 Hours. Note :- (a). Concrete for sunken slabs shall be mixed with WP compounds as manufacturdrs instructions before carrying out water proofing treatment the sunken slab slab shall be tested with water for 48 hrs for any leakage/dampeness is seen in ceiling below, then treatment is again carried out to RCC slab and it is again tested (Water proof compound rate will not be paid separately).

(b). 50mm thick PCC at the bottom of slab and slope shall be 1:20 toward the corner of outer wall and GI pipe of 50mm dia (Med grade) be inserted at corner projecting outside 20 cm . (c). 15 mm thick plaster in CM 1:3 mixed with WP Compound shall be provided while concrete is green (d). Only floor area shall be measured for payment purpose. (e). Treatement shall only be done from approved manufacturer & name of manufacturer required to be approved from GE before treatement. (f) Joints of trap/WC/Soil pipes shall be properly sealed with sealing compound.

Rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) three layered hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and as directed.

Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) three layered hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and as directed.

PCC 1: 2 : 4 type B-0 ( using 12.5mm graded crushed stone agg.) 50mm thick as in floor finishing surfaces of conc topping even and smooth without using extra cement as in base of water storage tanks including use and waste necessary form work for smooth finished surfaces etc.

Taking down cement plaster from brick or stone walls and ceiling incl racking out joints hacking for key, scrubbing down with water etc.

Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work including finishing the surfaces fair and even without using extra cement complete all as specified and as directed.

Rendering 10 mm thick in cement mortar 1:6 on other than fair faces of brick work including finishing the surface even and smooth without using extra cement complete all as specified and as directed.

Rendering 5mm thick cement plaster with cement and sand mortar(1:3) on concrete surface as in ceiling finished even and smooth without using extra cement all as specified and directed.

Demolition of brick work built in cement mortar including all quions, arches , pillars etc.

Brick work with sub class 'B' bricks , straight or curved on plan exc. 6 mtr mean radius built in CM 1:6 complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

Preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed.

Preparation of new plastered surface and apply two coat of Oil bound distemper over & including alkali resistant primer on ceiling complete all as specified and as directed.

Complete removal of exising treatment of old surfaces and apply two coat of oil bound distemper to walls over 2mm thick wall care Putty all as specified and as directed.

Complete removal of existing treatment and applying 2mm thick wall care putty on internal/external walls and ceiling all as specified and as directed.

Preparation of Old plastered and unplastered surfaces of walls and applying two coats of oil bound distemper, washing, rubbing, stopping brooming down with steel wire brushing all as specified and directed.

Preparation of Old plastered and unplastered surfaces of walls and applying one coat of oil bound distemper white/tinted including filling small depressions by putty , washing, rubbing, stopping brooming down with steel wire brushing all as specified and directed.

Preparation of Old decorated surface and applying one coat of Oil bound distemper on ceiling including filling small depressions by putty , washing, rubbing, stopping brooming down with steel wire brushing all as specified and as directed.

Preparation of old surfaces and applying two coat of cement base paint to walls including brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efforescent salts and removing oil and greasy spots all as specified and as directed.

Preparation of old treated surfaces of walls (plastered or unplastered) and applying two coats of Apex emulsion paint and roof projection/chajjas etc complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on wall surface, complete all as specified and directed. Note:- (i) The work shall be carried out in different shade and the same shall be got approved from Engineer-in-charge/GE/ (ii) The work shall be carried out upto 4th storey of bldgs and no extra payment shall be admissible for necessary form work & scaffolding required for the same.

Preparation of Old plastered and unplastered surfaces of walls,washing, rubbing, stopping,brooming down old distempered/painted surface with steel wire brushes including filling small depressions by putty and applying one coat of Interior plastic Emulsion paint 1st quality (White/Tinted) incl priming of surface all as specified and directed.

Preparation of Old plastered and unplastered surfaces of walls,washing, rubbing, stopping,brooming down old distempered/painted surface with steel wire brushes including filling small depressions by putty and applying two coats of interior plastic Emulsion paint 1st quality (White/Tinted) incl priming of surface all as specified and directed.

Preparation of old painted steel surfaces of any description over 10 cm width of girth not other wise described and applying one coat of synthetic enamel paint all as specified.

Preparation of old painted wooden surfaces of any description over 10 cm width of girth not other wise described and applying one coat of synthetic enamel paint all as specified.

Taking down chowkats or frames exceeding 1.5 Sqm and n.exc 4.00 sqm each with shutters (without taking off shutters from the frames) all as specified and directed.

All as per item No-26 here-in-before but, but not exceeding 1.5 sqm.

Taking down shutters of any description exc 1.00 Sqm and not exc 2.00 Sqm each and removing from site, complete all as specified and directed

Taking down shutter of any description area exc 1 sqm but not exc 2.0 sqm each & re-fixing same in same opening after resecuring the edges if required, complete all as specified and directed.

Pressed steel frames for doors with one or more rebates of size 125x60mm including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh hold bar complete all as specified and as directed.

Pressed steel frames for doors with one or more rebates of size 105x60mm including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh hold bar complete all as specified and as directed.

Factory made solid panel PVC door shutter/ cupboard shutter/ kitchen cabinets 30mm thick style wooden texture consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site, complete all as specified and directed.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified and as directed.

S&F in replacement of Kitchen cabinets of PVC Solid board(wooden texture) size 900mmx750mmx600mm, including partitions, shelves and drawers with brass sliding rails,channels,door handles, door catchers, overall cabinet internally and externally made with both side PVC laminated termite proof board, 18/19 mm thick, ISI marked including PVC kitchen/cup board frame of size 18mmx63mm made out of 18mm thick PVC pre-laminated ply coloured and frame shall be fixed with 50mm long steel screw inside using drilling machine and plastic fasteners, having following specifications: .....Contd to Srl item No 34.01

(i)Outer frame made six 50mmx47mm with same board. (ii)Shutters both side PVC laminated termite proof board, 18/19 mm thick having continuous piano stainless steel hinges of 30mm flap width with one No brass handle of 75mm including brass door catcher of not less than 50mm size in each shutter. (iii) Drawers made of both side PVC laminated termite proof board, 18/19 mm thick including brass handles of front and two sliding rails at sides in each drawer. (iv) All cabinets, drawers, frames, partitions and boards shall be fixed at site with brass machine screws and PVC plugs of suitable sizes. Note: (a) Only front face dimensions at site (Length and Height), shall be measured and entered in MB irrespective of Nos of partitions or drawers. Cost of all partitions as required at site shall also be deemed to have included in quoted rates and nothing extra is admissible on this account. (b) Different No of partitions and drawers may be as per site requirement with out any extra cost. (c) All labours and materials cost shall be deemed included in quoted rate.

PCC 1:2:4 type B-0 (Using 12.5 mm graded crushed stone aggregate) as in filling of pressed steel frame and as in parapet coping all as specified and directed.

PCC 1:3:6 type C-1 (Using 20mm graded crushed stone aggregate) for hold fast blocks, including necessary form work for rough finished surfaces etc complete all as specified and as directed.

Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Powder coated aluminium anodised door shutters(minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

Powder coated anodised aluminium window / ventilator( glazed / gauged skeleton shutter ), (minimum thickness of powder coating 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21 100mm long (2 No. ) suitable handle (1 No.) complete all as specified and as directed.

Door closer hydraulically regulated, aluminium extruded section body designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed in repairs complete all as specified and as directed.

M&L 35mm thick flush shutters, solid core with particle board exterior grade as per IS 2202 of 199 (Part-I) flush door shall be internally lipped as per clause .8.52.2 of SSR Part-I 2009 complete all as specified & as directed.

30mm thick 2nd class hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

Mild steel springs for doors, 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete.

100 mm butt hinges, medium weight cold rolled mild steel, complete all as specified.

Aluminium handles cast type anodised of size 150mm with screws long ISI marked complete all as specified.

Aluminium anodised barrel tower bolt 150 mm, extruded section ISI marked complete all as specified.

S&F in repair auto hinges 105 degree opening made out of stainless steel, complete all as specified and as directed.

S& F Hasp and stapple safety type of aluminium anodised 100 mm long as a cupboard locker.

Aluminium anodised sliding door bolts with hasp and stapple extruded section or cast aluminium alloy with length of bolt as 300 mm including fixing bolts complete all as specified.

Steel windows/ventilator (Box type) factory made with double shutter with or without devetailed bar ( gauzed & glazed shutter) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts in each shutter 100mm long with & including 8mm square bar grills, complete all as specified & as shown on drg No. CEUZ/TD/1269/2008 Sh No 1/1 to 1/3 . Note:-(a) Fixed type glass panes shutter if any provided in above same window shall be measured and paid separately & area of these fixed shutter shall be deducted from total area of box type window for payment purpose. (b) Sheet glass/ wire cloth shall be measured & paid seperately under respective item.

Description all as per Item No 50 above, but only glass pane shutter without glazing bars.

Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified.

Sheet glass ordinary quality, 4mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and as directed.

Figured glass pin headed type, 4mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified.

Floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue,nodised,with hard drawn steel spring,fixed in bottom body of door complete all as specified and directed.

Pre laminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw to timber frame in repairs as cupboard shelve and shutter, 19 mm thick in repairs, complete all as specified and directed.

Pre laminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw to timber frame in repairs as cupboard shelve and shutter, 12 mm thick. (Kitchen cup board/covered bottom shelf of cooking platform) fixed in repairs complete all as specified and directed.

External teak wood lipping 6 mm thick fixed with nails for 18/19 mm thick board, complete all as specified.

External teak wood lipping 6 mm thick fixed with nails for 12 mm thick board, complete all as specified.

Preparation of new or previously untreated steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer, complete all as specified and as directed.

Preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of Ist quality over a coat of pink primer,complete, all as specified and directed.

Taking down eaves gutters and rain water pipe , soil and waste pipe (any size or pattern ), including all fittings, heads , shoe bends , swan-necks etc. complete all as specified and directed.

110mm bore PVC SWR Type-B (pressure not less than 6 Kg/cm2) pipes single socket in any length with rubber joints laid trenches or in floors etc complete all as specified and as directed.

75mm bore PVC SWR Type-B (pressure not less than 6 Kg/cm2) pipes single socket in any length with rubber joints laid in floors with PVC/MS holder clamp etc complete all as specified and as directed.

PVC (SWR) bends any radius 110 mm bore with oval access door, complete all as specified and as directed.

PVC SWR bends any radius 75mm bore with oval access door complete all as specified.

PVC SWR 110mm dia Type-B ( pressure not less than 6 kg /cm2) pipes in any length fixed to walls with PVC/MS holder or clamps and conforming to IS-1729 complete all as specified and directed.

PVC SWR 75mm dia Type-B ( pressure not less than 6 kg /cm2) pipes in any length fixed to walls with PVC/MS holder or clamps and conforming to IS-1729 complete all as specified and directed.

PVC (SWR)110 mm junction single, (Single T) equal or unequal ordinary or inverted with spigot or socket branch with oval access door all as specified and as directed.

PVC (SWR) 75 mm junction single, (Double Y) equal or unequal ordinary or inverted with spigot or socket branch with oval access door all as specified and as directed.

PVC cowls 110mm fixed in repairs complete all as specified and directed.

PVC cowls 75mm complete all as specified and directed.

PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

Taking down unsv existing piping and S&F 16mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

Taking down unsv existing piping and S&F 20mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

CPVC Brass Elbow 16mm dia all as specified and directed.

CPVC Brass Elbow 20mm dia all as specified and directed.

Brass elbow 3/4x12 for 20mm outer dia of CPVC pipes, complete all as specified and as directed.

CPVC Brass Tee 16mm dia all as specified and directed.

CPVC Brass Tee 20mm dia all as specified and directed.

CPVC Male Brass Threaded Adaptor (MTA/ MBTA) 16mm all as specified and directed.

CPVC Male Brass Threaded Adaptor (MTA/ MBTA) 20mm all as specified and directed.

CPVC Brass Union 16mm dia all as specified and directed.

CPVC Brass Union 20mm dia all as specified and directed.

CPVC Brass Ball valve 16mm dia all as specified and directed.

CPVC Brass Ball Valve 20mm dia all as specified and directed.

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc., complete all as specified and as directed.

Mild steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Refixing of old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 20mm bore after cleaning including provn of new fittings, complete all as directed.

Mild steel galvanized steel tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete of 15 mm dia bore complete all as specified.

Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 15 mm bore after cleaning including provn of new fittings all as directed.

15 mm bore Gun-metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed high pressure with crutch or butterfly handle fixed in repairs complete all as specified and as directed.

20mm bore Gun-metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed high pressure with crutch or butterfly handle fixed in repairs complete all as specified and as directed.

Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified.

PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections fixed in repairs, complete all as specified and as directed.

Vitreous china squatting pan "Orissa Pattern" size 580 x 440 mm in white colour with integral foot rest incl lime mortor, 'S' trap fixed in repairs complete all as specified and as directed. Cat Part No-20042 (ORISSA PAN (ECO)) of Hindware or equivalent cat part of make NEYCER, CERA, PARRYWARE as approved by GE.

Vitreous china wash down water closet pan pedestal pattern size 570mm x 460mm x 380mm in white colour excluding seat cover, flushing cistern and flush pipe fixed in repairs complete all as specified and directed. Cat Part No-20011 of Hindware or its equivalent cat part of make specified in list make, as approved by GE.

S&F Vitreous China floor mounted Single piece wash down water closet pan (pedestal pattern)(size 370mm x 670mm x 720mm) with UF soft close slim seat cover,Hinges, Dual Flush cistern fitting, fixing accessories and set with "S" trap size 300mm including connection to drain (or outgoing pipe), antisyphonage pipe, etc.. complete fixed in repairs complete all as specified and directed.Make-Jaquar (Lyric) Cat Part No. LYS-WHT-38851S300UFSMN or its equivalent cat part of make specified in list make, as approved by GE.

Plastic water closet seat cover white closed pattern with flat bottom and cover including chromium plated hinges device fixed in repairs, complete all as specified and as directed.

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.2 meter long flexible spirochrome flex tube and ABS wall hook including making connections and fixed in repair in position complete in all respect as specified.Make-Jaquar Cat part no. ALD-573 or its equivalent cat part of make specified in list make, as approved by GE.

Toilet paper holder with flap recessed type stainless steel Complete all as specified and directed.Make-Jaquar cat part no. AQN-7753 or its equivalent cat part of make specified in list make, as approved by GE.

Vitreous china wall hung wash basin with fixing accessories, white, flat back, size 590mm x 490mm x 185mm full pedestal including 15mm bore CP Central hole Basin Mixer with Popup waste system with 450mm long braided hoses for mixing hot and cold water screwed down for iron pipe including 32mm dia waste coupling,waste pipe, cutting for and pinning in ends of brackets or erecting stand porcelain stopper a pair of CI brackets fixed in repair complete all as specified and directed by Engineer in charge.Make-Jaquar (Lyric) cat part no. LYS-WHT-38801 & LYS-WHT-38301 or its equivalent cat part of make specified in list make, as approved by GE.

Vitreous China urinal with CP spreader Chrome finish hole and fixing accessories Half stall type (back or corner wall type)(size 355mm x 340mm x535mm) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; including PVC Connection,waste pipe and coupling. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) fixed in repairs complete all as specified and as directed by Engineer-in-Charge. Make- Jaquar Cat part no. URS-WHT-13261H or its equivalent cat part of make specified in list make, as approved by GE.

Chromium Plated stainless steel towel rail 20mm dia 'D' type 60 cm long between flanges fixed in repairs Make-Jaquar cat part no. AKP-35711PS or its equivalent cat part of make specified in list make, as approved by GE.

PVC connection 15mm size with PTMT nuts on both ends of length 600mm fixed, complete all as specified and as directed.

Waste pipe for SINK/WHB/Urinal for 32/40mm dia fixed in repairs all as specified & as directed.

CP Sink coupling, 32mm bore brass, chromium plated for stainless steel sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and as directed.

C.P Swivel shower of any colour for fixing with 15 mm pipe ,with shower arm of size 195 mm long with bend of 45 degree with flange of any description (minimum weight 40 gm), supplied and fixed in repairs complete.

CP angle valve/concealed stop cock of cast copper alloy (ISI Marked) chromium plated fancy type screwed down high pressure with capstain head screwed both ends for iron pipe 15mm bore including fixing in repairs complete all as specified and directed. Cat Part No-SOL-6053 of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

Bib taps (Long body) for 15mm bore dia of pipe, fancy type chromium plated with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule and fixed in repairs complete all as specified and directed. Cat Part No-CON-107KN of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

Bib tap (long body) 15 mm standard of PTMT any colour high pressure screwed for iron pipe and fixed in repairs complete all as specified.

Chromium plated fancy type quarter turn Pillar cock screwed down high pressure with crutch or butterfly handle screwed both end 15 mm bore dia fixed in repairs all as specified. Make-Jaquar Cat part no. FON-40011 of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

15mm bore brass CP wall mixer with provision for overhead shower arrangement with 115mm long bend pipe on upper side for mixing hot and cold water supply screwed down with connecting legs CP extension nipple & wall flange connector for hand shower arrangement with connecting Legs, wall Flanges & wall bracket for hand shower for mixing hot or cold water, screwed for iron pipe and fixed in repairs, complete all as specified and directed. Make-SOL-6273UPR of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

CP Brass wall mixer 3-in-1 system with provision for both hand shower and overhead shower complete arrangement (With overhead and hand shower with 115mm long bend pipe on upper side,for mixing hot cold water supply screwed down incl connecting legs,CP Extension nipple & wall flanges for iron pipe 15mm dia bore fancy type in repair complete all as specified and directed. Cat part no. SOL-6281 of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

Brass CP mixer for sink, cast copper alloy (ISI Marked) fancy type chromium plated for mixing hot and cold water screwed down high pressure with capstain head screwed both ends for iron pipe 15mm bore including connecting legs, CP extension nipple and wall flange fixed in repairs complete all as specified and directed. Cat part No-QQT-7219 of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

CP Brass swan neck Pillar cock with left/right hand operating knob with 450mm long braided hose screwed down for iron pipe 15mm dia bore fancy type fixed in repair complete all as specified and directed. Cat part no. CON-123BKN/127BKN of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

CP grating with or without hole100 mm dia fixed in repairs all as specified and as directed.

Stainless steel Soap dish, any type, fixed with plugs chromium plated brass screws fixed in repairs complete all as specified and as directed. Cat part No-AQN-7733 of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

5.5 mm thick Frameless wall mounted decorative Looking mirror with bevelled edge made out of premium glass, provide a clear and normal reflection incl installation with full round brass holder and top cap of heavy duty stainless steel with minimum of 4 pieces in one mirror. Pattern and size of Mirror will be decided as per site requirement by AGE,all as specified and as directed.

Dazzle Kitchen Modular BWR Plywood Vanity Washbasin Cabinet (White) size 450mm x 760mm x 830mm, made out of PVC laminated BWR plywood drawers(2 or 3 nos) on right side with one nos handle at front and two nos sliding channel at both end of drawer. A cabinet should be provided on left side having two doors of PVC membraned plywood internally partitioned vertically into two parts and door shutter must be fiitted with auto hinges. Provision of wash out pipe for passage of waste water will be given and connected with existing floor trap/grating and CP Fency type tall basin Mixer of Parryware cat part no. G3946A1 or its equivalent cat part of make specified in list make, as approved by GE. screwed down for 15mm bore iron pipe fixed all as specified and as directed.

Plate rack made of High quality stainless steel not less than 0.80mm thick overall size 910mm x 762mm x 254mm fixing by means of electrical drill machine, fasteners and screws, fixing in repairs, complete all as specified and directed.

Stainless Steel sinks with drainage board made of stainless steel (1mm thick) kitchen or laboratory with plugs,washers and wastes pipes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets fixed as in repairs and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm as approved by Engr-in-Charge complete all as specified and directed.

Bib taps 15 mm, fancy type Chromium plated with wall flange screwed down for iron pipe or for brass ferrule and fixed in repairs complete all as specified. Cat part no. LYR-38037 of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

Corner Sheet glass shelf assembly consisting of 5.5mm thick glass shelf with chromium plated bracket guard and railing 60cm long fixed in repairs Cat Part No AKP 35771P of Jaquar or its equivalent cat part of make specified in list make, as approved by GE. complete all as specified.

Glass shelf 600mm long consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing with brackets fixed in repairs all as specified and as directed. Cat part no. AKP-35771P of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

Fabrication and fixing of Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary , gusset plates, riveting etc n exc 10 Kg each brackets, conforming to Fe.290. Gde E-165 (Brackets over 10 Kg each to be measured under "Structural Steel") Complete all as specified and directed.

Repair to balcony/Facia/Roof projections and soffit of chajjas etc by taking down old rendering and hacking clearly the edges and corners smooth rounded for new plastered area exceeding 30sqm in width or girth & providing 15 to 20mm thick plastering to match with the existing thickness in CM 1:3 and including formwork up to height 6.5 mtr above ground level of bldg including two coat of Apex/cement based paint over one coat of primer complete all as specified.

Solid PVC Wall Panelling/Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing all as specified and as directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Non skid coloured ceramic tiles 7 to 8 mm thick(square / rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick screed bed in CM (1:4) finished fair and even, complete all as specified and directed.

Non skid Ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in skirting/dado etc. Set and jointed in neat cement slurry and pointed in coloured cement to match including 10 mm thick rendering, plaster in cement and sand mortar 1:4 finished even and fair complete all as specified and directed.

Glazed ceramic coloured tiles (450x350mm) x 7mm thick on vertical surfaces such as skirting, dados and risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in CM 1:4 on other than fair faces of brick work finished even and fair to receive tiles, complete all as specified and directed.

Granite (of any type) work 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like including pointing in white cement (1:2) using marble dust with admixure of pigment to match with shade of granite including 15mm thick screed of CM 1:4 after applying cement slurry@3 kg/sqm of cement per sqm, complete all as specified. (Note : A hole shall be drilled in the Granite after fixing for gas pipe all as directed by Engr-in-Charge).

Vitrified ceramic tiles (Light shade) 10mm thick (square /rectangular) polished, area of each tile n.exceeding 0.36 sqm laid as in floors, set and jointed in neat cement slurry and pointed in white/coloured cement to match with shade of tiles including 15mm thick screed bed in cement and sand mortar 1:4, complete all as specified and directed.

Description all as per Item No 136 above, but in skirting/dado over and including 10mm thick rendering in CM 1:4.

Curtain rod 20mm dia Stainless steel fixed with and including two Nos of bracket & side cup including taking down of old unserviceable curtains rods, complete all as specified.

Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement at necessary holes for smooth finishing complete all as specified and directed complete all as specified and directed.

Material and labour for point wiring complete with 1.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade and including cutting, chasing work at any height and all accessories are concealed in walls / roofs / floors / ceiling etc. metal flush box with top,bottom,side/back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloures and including 1.5 Sqmm PVC insulated multistranded FRLS type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for the following:- (Note:- All necessary accessories such as modular steel box,top cover plate, blank plate, screws,washers to be used of same make/brand only and shall be deemed in to included in quoted rate only.)

All as per item No-140 above but for One light point/fan /bell point controlled by one switch.

All as per item No-140 here-in-before but for One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board .

All as per item No-140 here-in-before but for One 5 pin 6 amps socket point controlled by one 6 amps switch on same board .

Material and labour for point wiring complete with 2.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade and including cutting, chasing work at any height and all accessories are concealed in walls / roofs / floors / ceiling etc. metal flush box with top,bottom,side/back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloures and including 2.5 Sqmm PVC insulated multistranded FRLS type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for the following:- (Note:- All necessary accessories such as modular steel box,top cover plate, blank plate, screws,washers are to be used of same make/brand only and shall be deemed in to included in quoted rate only.) for One 15 amps power socket outlet point controlled by one 16 amps switch on independent board.

Modular type switch 6 Amps, single pole, 1way,1 module, 240V, ISI Marked Complete all as specified and directed.

Modular type switch 16 Amps, single pole, 1way,1 module, 240V, ISI Marked Complete all as specified and directed.

Modular type socket shuttered type 6 Amps, 2/3 Pin combined 2 module, 240V, AC ISI Marked Complete all as specified and directed.

Modular type socket 6 A/16 Amps, 2/3 Pin combined shuttered socket 2 module with light indication ,240V,AC ISI Marked Complete all as specified and directed .

Fan regulator modular type electronic compatible with BLDC fan, stepped type 100 Watts, 2 module 240Volts, AC ISI marked complete all as specified and directed.

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 12 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging, blanking plates where required testing and commissioning in replacement, complete all as specified. Make:- Havells cat part No-DHDPSHODPW12 or its Equivalent cat part of make of Legrand / ABB / L&T as approved by GE.

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 8 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging, blanking plates where required testing and commissioning in replacement, complete all as specified. Make:- Havells cat part No-DHDPSHODPW08 or its Equivalent cat part of make of Legrand / ABB / L&T as approved by GE.

Sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FRLS type, PVC insulated, unsheathed,flexible,multi stranded colour coded cables drawn through and including rigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc concealed in wall/roofs/floors and including one run of 2.5 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLS type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface including cutting and cheasing and complete all as specified and directed. Note : - Two run of 6 sqmm single core copper conductor cable and one run of 2.5 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit.

Supply and fixing in replacement Integrel sleek surface mounted LED fitting fixture( 4 feet length), 18 watt with integral electronic driver complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size cable incl testing after fixing all as specified and approved by GE. The specification of the light fitting should meet the following:- (a) Housing of Light fitting : aluminium Extruded (b) Operating voltage : 150 v to 270 v (c) Operating temprature : -10 to 45 degrees (d) Lumen efficacy : 100 lumen per watt (e) system lumen : Not less than 1800 lumens (f) Colour temprature : Not less tha 5700k (g) Surge voltage protection : Up to 2 KV (h) Ingress protection : IP20 (j) Total harmonic distortion : not less than 20% (k) Power factor : not less than 0.90 (l) Input Frequency : 50 HZ (m) Line protection : Under/ Over voltage protection

Supply and fixing in replacement of 10 watt Bulkhead Designed with beautiful aesthetics using new generation technology in LED to enliven your outdoor and indoor areas in perfect synchronization with functionality and aesthetics. Family of bulkhead Lights designed to compliment thegeometry of the area with modern design. High quality polycarbonate UV Protected milkydiffuser is used for glare free light distribution complete making connection and testing after fixing all as specified and approved by GE. The specification of the panel light fitting should meet the following:- (a) Housing of Light fitting : Die cast Aluminium (b) Polycarbonate UV protected diffuser (c) Operating voltage : 140 v to 270 v (d) operating temprature : -10 to 45 degrees (e) Lumen efficacy : 100 lumen per watt (f) system lumen : Not less than 900 lumens (g) Colour temprature : Not less than 5700K (h) Surge voltage protection : Up to 4 KV (j) Ingress protection : IP65 (k) Total harmonic distortion : not less than 20% (l) Input Frequency : 50 HZ

Supply and fixing in replacement of 36 watt 2x2 panel Ultra modern recess mounting luminaire with high performance LEDs, suitable for mounting with Armstrong/ Grid ceiling Delivers excellent illumination & comfort in high ceiling areas Long life & photobiologically safe LED’s High performance electronic driver ensures zero maintenance No harmful UV & IR radiations Environment friendly as it does not contain Mercury Instant light, High transmittance PMMA opal diffuser for glare free symmetric light distribution.Powered by an Built-In electronic driver (SMPS based constant current supply) complete making connection and testing after fixing all as specified and approved by GE. The specification of the panel light fitting should meet the following:- (a) Housing of Light fitting : CRCA Powder Coated (b) Operating voltage : 150 v to 270v (c) operating temprature : -10 to 45 degrees (d) Lumen efficacy : 110 lumen per watt (e) system lumen : Not less than 3600 lumens (f) Colour temprature : Not less tha 5700k contd to item No-152.01

(g) Surge voltage protection : Up to 2 KV (h) Ingress protection : IP20 (j) Total harmonic distortion : not less than 20% (k) Power factor : not less than 0.90 Line protection : Under/ Over voltage protection (l)nput Frequency : 50 HZ

Supply & fixing and in repairs MCB SP 6 to 32 Amps 10 KA,"C" series,AC,240Volts,50Hz , ISI marked complete all as specified and directed.Make:- Legrand cat No.4085 87 to 4085 95 / Hager Cat Ref No.NCN106N to NCN132N / Havells Cat No.DHMGCSPF006-032 as approved

Supply & fixing and in repairs MCB SPN 32 to 40 Amps 10 KA,"C" series,AC,240Volts,50Hz, ISI marked complete all as specified and directed.Make:- Legrand cat No.4086 17 to 4086 18/ Hager cat part No:- NCN232N /Havells cat part No.DHMGCSNF040 / L&T cat part NoBB20400C as approved

M/s Vishwakarma Enterprises

M/S KARAN SINGH CONTRACTOR

MAMTA ENTERPRISES