COMPLETION OF INCOMPLETE WORK OF PROVN OF OTM ACCN FOR ENGINEERING REGIMENT AT TEZPUR

Amount

NOTE (Applicable for all parts/items/):- The bidders/contractors are advised to read tender document, all drawings & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates. Lumpsum price workedout by the tenderer for BUILDING & STRUCTURES as listed in Schedule ‘A’ Part-I

Lumpsum price workedout by the tenderer for SITE CLEARANCE, SITE DEVELOPMENTS & EARTH WORKS as listed in Schedule ‘A’ Part-II.

Lumpsum price workedout by the tenderer for INTERNAL WATER SUPPLY/ HOT WATER SUPPLY as listed in Schedule ‘A’ Part-III.

Lumpsum price workedout by the tenderer for INTERNAL ELECTRIFICATIONS as listed in Schedule ‘A’ Part-IV.

Lumpsum price workedout by the tenderer for ROADS / CULVERTS/ HARD STANDING as listed in Schedule ‘A’ Part-V.

Lumpsum price workedout by the tenderer for SEWAGE DISPOSAL as listed in Schedule ‘A’ Part-VI.

Lumpsum price workedout by the tenderer for AREA DRAINAGE as listed in Schedule ‘A’ Part-VII.

Lumpsum price workedout by the tenderer for COMPOUND WALL/ SECURITY FENCING/ GATE as listed in Schedule ‘A’ Part-VIII.

Lumpsum price workedout by the tenderer for EXTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-IX.

Lumpsum price workedout by the tenderer for EXTERNAL ELECTRIFICATION/ LIGHTING PROTECTION/ WATER COOLER/ REFRIGERATION as listed in Schedule ‘A’ Part-X.

Lumpsum price workedout by the tenderer for DEMOLITION & DISMANTLING as listed in Schedule ‘A’ Part-XI.

Lumpsum price workedout by the tenderer for FIRE ALAM AND FIRE FIGHTING as listed in Schedule ‘A’ Part-XII.

Sch 'A' Sec-XIII (Miscellaneous Items)Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only.

Supply and fixing ceiling fan enery saving and fancy type 1200 mm(minimum) sweep three blade, 5 star BEE rating without regulator including hanging rod and necessary connecting PVC insulated Flexible cable for connection from ceiling rose to fan and connecting complete all as specified. Make: Model- ES-50 of Havells or equivalent make as per Appendix 'B'.

Wall mixer with provision for overhead shower with 115 mm long bend pipe on upper side, connectiing legs & wall flanges of copper alloy chromium plated , and fixed for 15 mm bore pipe and all accessories complete all as specified and as directed. Make:- Cat No CON 273 KN UPR of Jaquar or equivalent model of make list as given in Appdix "B".

Exhaust fan 225mm(min) sweep MS CRCA body and metal blades with double bearing metal protective bird guard , AC single phase, including electrical connection with twisted three core PVC insulated flexible cord of size 0.75sqmm copper conductor from celing rose complete all as specified and as directed. Make: Model- Ventil Air - DS of Havells or equivalent make as per Appendix 'B'.

Supply and fixing cabling for fire detection and alarm system with 2 core 1.5 sqmm 1100V annealed tinned copper conductor PVC sheathed, flexible, unarmoured cables in PVC conduits complete all as specified.

Pillar cock cast copper alloy screwed down with long neck with aerator complete all as specified and as directed. Make:- Jaquar Cat No CON 021 KN or equivalent model of make list as given in Appdix "B".

Exhaust fan 300mm(min) sweep MS CRCA body and metal blades with double bearing metal protective bird guard , AC single phase, including electrical connection with twisted three core PVC insulated flexible cord of size 0.75sqmm copper conductor from celing rose complete all as specified and as directed. Make: Model- Ventil Air - DX of Havells or equivalent make as per Appendix 'B'.

Supply and Fixing wall mounting fan 400 mm sweep,fixed on wall including necessary connecting PVC insulated flexible cable for connection from ceiling rose to fan and connecting complete all as specified. Make Crompton greaves Cat HIGH FLO WALL or equivalent make as per Appendix 'D'.

Outdoor wall mount decorative luminaire light fitting for 1 x 18 Watt including PLC lamp made of die cast aluminum wing shaped powder coated housing with suitable colour vision inluding connection complete all as specified and directed . MAKE: Philips Cat No HWS 370 1x PL-C /2 P 18W GR or equivalent model of make list as given in Appdix "B".

Fluorescent building security light luminaire 1 x 28 watt including 1 x28 watt tube made of aluminium housing with UV stabilized clear acrylic cover, electromagnetic ballast and fixed on pole with 40 mm dia light grade GI pipe (bend to shape) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 50 x 6 mm MS flat) nuts, bolts & washers incl painting the clamps with two coat of aluminium paint over a coat of red oxide primer including connection complete all as specified and directed . Make : Model No- HGS 120 1x TL5 28 W EBE of Philips or equivalent model of make list as given in Appdix "B".

Supply and fixing MCCB 125 amps, 4 pole, breaking capacity 25 KA suitable for operation of 415 volts AC 50 HZ with megnatic thermal setting including making necessary electric connections complete all as specified and directed by Engineer-in-Charge.

Sheet metal enclosure verticaly distribution board TPN 415 Volt 4 way ,double door type and provision for 4 pole MCCB as a incomer complete with 100 Amps rated vertical insulated busbar .

Supply and Fixing industrial type exhust fan 240V, 450mm sweep, 950 RPM with lowers and shutters fixed to wall and provn of cable upto ceiling rose complete all as specified and as directed. Make: Model- Supreme DLY of BAJAJ of Havells or equivalent make as per Appendix 'B'.

Supply and fixing MCCB 100 amps, 4 pole, breaking capacity 25 KA suitable for operation of 415 volts AC 50 HZ with megnatic thermal setting including making necessary electric connections complete all as specified and directed by Engineer-in-Charge.

MCCB 4 pole, 63 Amps capacity, bearking capacity 25 KA with fixed thermal and fixed magnetic setting

Supply and fixing MCCB 4 pole, 40 Amps capacity, bearking capacity 25 KA with fixed thermal and fixed magnetic setting complete all as specified.

Supply, installation, connection, testing and commission of Sub-main Distribution MCCB panel board with provision of one incommer MCCB( upto 250 amps ) and 4 nos outgoing MCCB(100amps Maximum),250 amps rating, tinned copper bus-bar, indoor type, wall mounted including fully epoxy polyester powder coating painting, double door shutters , locking arrangement and including all internal & external accessories as per manufacture instructions and complete all as specified and as directed:- Make :- Cat no DA20D1044CZZ0 of L&T or equivalent model of Havells/ ABB/ LEGRAND/ SCHNEIDER/ SIEMENS

Lamp holder, PVC/Polycarbonate type with black plate suitable for batten fittings and including 1x 15 watt CFL lamp.

Supply and fixing modular TV coaxial socket outlet fixed in 1 M box comprising of flush metal box, inner plate and outer cover complete all as specified.

Supply and fixing modular telephone jack RJ-11white colour fixed in 1 M box comprising of flush metal box, inner plate and outer cover, all conforming to IS 3854 :1997 with finger proof terminals with captive screws having front fixing & removing features without removing plates complete all as specified.

Supply and fixing modular telephone jack RJ-45 white colour fixed in 1 M box comprising of flush metal box, inner plate and outer cover, all conforming to IS 3854 :1997 with finger proof terminals with captive screws having front fixing & removing features without removing plates complete all as specified.

Microprocessor based single phase electronic temper proof energy meter class 1.0 accuracy conforming to relevant IS15959-2011/ CEA/ CBIP technical report 88 suitable for LT, single phase, 2 wire, 240 volt system, IP 51 protection, of rating 5 to 30 Amps, with optical communication port for data downloading, authenticated billing information, recording at least last 6 months history data for KWH consumption and load survey data for KQ/KVA for atleast last 35 days including safe high grade, transparent engineering polycarbonate casing of projection mounting type, thickness of box to be 2 mm and IP 54 protection complete all as specified and directed. Make : L&T / NEPTUNE / SECURE METERS/ SCHNEIDER/ SIEMENS

Supply & fixing of transparent street light junction box of size 200 mm x 160 mmx98 mm made of high quality polycarbonate I IP-65 (Dust and power jet Proof according to IEC 60529) , shock proof, rust free, corrosion free acid and chemical resistant, fire retardant having high impact (IK 08) totally insulated (Class II ) made of halogen and silica free recyclable material, UV resistant having high grade gasket made of polyurethane with copper bus bar 25 x 5 mm -04 strip, one no MCB DP 6 Amps with locking arrangement and 2 Nos M40 size cable gland and one M32 size gland suitable up to, 50Sqmm cable etc complete all as specified and directed Make: HENSEL Cat No KF 9255or equivalent model of BCH/LEGRAND

Post top latern fitting suitable for 2x26 Walt CFL lamp including 2x26 watt CFL lamp and all other standerd accessories fixed on 40mm dia GI pipe appx 50cm long (light grade) embedded in PCC including all electrical connections with weather proof stranded aluminium conductor cable of suitable length of size 1.5 sqmm 2 core. Make : BNOB 226 Opal of Bajaj or equivalent make as per Appendix 'B'."

Supply & Fixing Fire Extinguishers of Capacity 9.0 KILO-GRAM (PUMP ROOM & DG SET), Mechanical Foam Type, consisting of welded Mild Steel Cylindrical Body Squeeze Lever Discharge Valve 300mm long high pressure discharge hose, discharge nozzle, suspension bracket, ISI marked as per IS:10204, finishing Externally with Red Enamel Paint and fixed to Wall with Brackets with Internal Charge, complete all as specified and as directed.

LED street light fitting 60 Watt, di- cast aluminium housing with UV stabilized polycarbonate cover including driver , suitable type gasket and IP 65 portion and fixed on pole with 40 mm dia light grade GI pipe (bend to shape) bracket 1.5 mtr long complete with MS flat iron clamp (clamps shall be 50 x 6 mm MS flat) nuts, bolts & washers inclding painting the clamps with two coat of aluminium paint over a coat of red oxide primer including connection complete all as specified and directed . Make : Model No- BRTFG60W LED Bajaj or equivalent model of make list as given in Appdix "B".

Supply & Fixing Carbon-di-Oxide Fire Extinguisher of Capacity 5 KILOGRAM consisting of welded Mild Steel Cylindrical body, Squeeze Lever Discharge Valve fitted with Internal dis-charge Tube, 300mm long high pressure Discharge Hose, Discharge Nozzle, Suspen -sion Bracket, confirming to IS:2878 finishing Externally with Red Enamel Paint and fixed to Wall with Brackets With Rawl Plug/Dash Fasteners with Internal Charge, complete all as specified and as directed.

Supply and installing at approved location approved make fire buckets of 24 gauge galvanized steel sheet, standard 13 litre capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letters “FIRE” in black and gold with and including MS stand duly painted with 2 coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified. Cost shall be inclusive of providing MS stand duly painted over a coat of primer.

Supply & Fixing Stored Pressure ABC Fire Extinguisher of Capacity 5.0 KILOGRAM, consisting of welded Mild Steel Cylindrical Body Squeeze Lever Discharge Valve 300mm long high pressure discharge hose, discharge nozzle, suspension bracket, ISI marked as per IS:13849 finishing Externally with Red Enamel Paint and fixed to Wall with Brackets with Internal Charge, complete all as specified and as directed.

Supply and fixing voltage stabilizer for automatic operation, single phase with neutral, air cooled indoor type and designed for input voltage variation between 170 volt to 250 volt with output voltage stabilized at 230 volt with accuracy of +/- 2.5% and capacity of 0.5 KVA complete all as specified.

Supply and fixing voltage stabilizer for automatic operation, single phase with neutral, air cooled indoor type and designed for input voltage variation between 170 volt to 250 volt with output voltage stabilized at 230 volt with accuracy of +/- 2.5% and capacity of 1 KVA complete all as specified.

Supply, installation, testing & commissioning Pre-filter of single candle with enclosure for filtering impurities upto 5 micron complete all as specified and directed. Make : Aquaguard/Kemflo

Material and labour for pre - cast RCC post HT cable route indicator made up of RCC (1:2:4) of overall size 100 x 100 x 1200 mm (H) and 200x200mm bottom with 4 nos 8 mm dia TMT bar on vertical and 8 mm TMT stirrups at 150c/c incl binding wire and embossing "MES HT CABLE" on all four sides and fixed at cable trench during returning filling of soil keeping 500mm above ground complete all as specified and as directed.

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminum bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING :- (i) MCCB 250 Amps, 4 pole, 415 V, 36 kA with earth leakage modules - 1 No (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear and not less than 200 Amp (iii) LED phase indicator and panel fuse -01 set of 3 (iv) Onload change over switches 315 A, 4 Pole:-01 No OUTGOING:- (i) MCCB 100A 4 Pole 415 V 25 KA -02 Nos ( Admin block left & right wing ) (ii)MCCB 160 Amps, 4 pole, 415 V, 25 kA-01 Nos (fire fight pump house) (iii) MCCB 25 Amps, 4 pole, 415 V, 16 kA-05 Nos (iv)MCB DP 6-32 Amps, 240 V 'C' curve, 10 KA-06 Nos. (Three MCB DP in one cubical) (v) Street light timer with 3 pole power contactor 25 Amps -1 set (vi) space for one MCCB 4 Pole upto 100 amps

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminum bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING :- (i) MCCB 160 Amps, 4 pole, 415 V, 36 kA with earth leakage modules - 1 No (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear and not less than 200 Amp (iii) LED phase indicator and panel fuse -01 set of 3 OUTGOING:- (i)MCCB 63 Amps, 4 pole, 415 V, 25 kA-03 Nos (ii) MCCB 25 Amps, 4 pole, 415 V, 16 kA-04 Nos (iii)MCB DP 6-32 Amps, 240 V 'C' curve, 10 KA-03 Nos. (Three MCB DP in one cubical) (iv) space for one MCCB

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminum bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING :- (i) MCCB 200 Amps, 4 pole, 415 V, 36 kA with earth leakage modules - 1 No (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear and not less than 200 Amp (iii) LED phase indicator and panel fuse -01 set of 3 OUTGOING:- (i) MCCB 63 Amps, 4 pole, 415 V, 16 kA-04 Nos (ii) space for one MCCB 4 Pole upto 80 amps

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminum bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING :- (i) MCCB 200 Amps, 4 pole, 415 V, 36 kA with earth leakage modules - 1 No (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear and not less than 200 Amp (iii) LED phase indicator and panel fuse -01 set of 3 OUTGOING:- (i) MCCB 63 Amps, 4 pole, 415 V, 16 kA-05 Nos (ii) space for one MCCB 4 Pole upto 80 amps

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminum bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING :- (i) MCCB 125 Amps, 4 pole, 415 V, 16 kA with earth leakage modules - 1 No (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear and not less than 200 Amp (iii) LED phase indicator and panel fuse -01 set of 3 OUTGOING:- (i) MCCB 100 Amps, 4 pole, 415 V, 25 kA-01 Nos (ii) MCB DP 6-32 Amps, 240 V 'C' curve, 10 KA-10 Nos.(Three MCB DP in one cubical) (iii) MCB 4 P 16 Amps, 415 V, 10 kA-01 Nos (iv) Space for one MCCB 4 Pole upto 100 amps

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminum bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING :- (i) MCCB 100 Amps, 4 pole, 415 V, 16 kA with earth leakage modules - 1 No (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear and not less than 200 Amp (iii) LED phase indicator and panel fuse -01 set of 3 OUTGOING:- (i) MCCB 63 Amps, 4 pole, 415 V, 16 kA-03 Nos (ii) MCB 6-32 Amps,2 pole, 240 V 10 KA-01 Nos. (iii) Space for one MCCB 4 Pole upto 80 amps

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminum bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING :- (i) MCCB 100 Amps, 4 pole, 415 V, 16 kA with earth leakage modules - 1 No (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear and not less than 200 Amp (iii) LED phase indicator and panel fuse -01 set of 3 OUTGOING:- (i) MCCB 63 Amps, 4 pole, 415 V, 16 kA-04 Nos (ii) MCB 6-32 Amps,2 pole, 240 V 10 KA-01 Nos. (iii) Space for one MCCB 4 Pole upto 80 amps

Supply, installation, testing and commissioning of factory made powder coated (CPRI approved) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminum bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING :- (i) MCCB 250 Amps, 4 pole, 415 V, 36 kA with earth leakage modules - 1 No (ii) 4 strip aluminum coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear and not less than 200 Amp (iii) LED phase indicator and panel fuse -01 set of 3 OUTGOING:- (i) MCCB 100 Amps, 4 pole, 415 V, 25 kA-02 Nos (ii) MCCB 63 Amps, 4 pole 415 V 16 KA-01 Nos. (iii) Space for one MCCB 4 Pole upto 80 amps

Supply and laying of 2.5 mm thick synthetic insulating mat/sheet for 11 KV/ 6.6 KV substations all as specified in SSR Part-I clause no 19.23A and IS 15652.

Supply, installing, testing and commissioning of outdoor modular type factory made by original equipment manufacture , Auto / manual power factor Corrector LT panel made out of CRCA 2mm thick duly pretreated & powdered coated finish with iron angle base frame support floor mounted, suitable for 3 phase 415 volt, 50 Hz system comprising of and including the following for achieving 0.99 power factor: - (a) MCCB TP of suitable amps capacity, minimum breaking capacity 25 KA – 01 No (b) Busbar TPN copper of suitable capacity – 01 Set (c) Metalised polypropylene capacitor (MPP) , Heavy duty type with (12.5 x 2+5x 2) Capacity 35 KVAR Banks ,Total 35 KVAR. (Each capacitor shall have inrush current limiting coils.) (d) Suitable back up protection for each capacitor bank of with HRC Fuse links with base. (e) Air break contactor of capacitor duty as per IS 13947 for Each capacitor bank. (f) Automatic / Manual Power Factor Control Relay unit for sensing Power Factor & monitoring on / off operation of contactors as per requirement of power factor improvement. & measuring instruments etc complete. (g) Internal power & control wiring with suitable size of PVC insulated copper conductor cable. (h) One Suitable capacity CT shall be installed at Existing LT panel & suitable control wiring from this CT to auto power factor corrector panel. (j) Any additional Accessories as provided by OEM for proper functioning of auto power factor corrector Panel. Make- L&T type IntellVAr-S , Neptune – Ducati or equivalent model of make list as given in Appdix "B".

Supply & Fixing Stored Pressure ABC Fire Extinguisher of Capacity 25 KILOGRAM, consisting of welded Mild Steel Cylindrical Body Squeeze Lever Discharge Valve 300mm long high pressure discharge hose, discharge nozzle, suspension bracket, ISI marked as per IS:13849 finishing Externally with Red Enamel Paint and fixed to Wall with Brackets with Internal Charge, complete all as specified and as directed.

Supply & Fixing Stored Pressure ABC Fire Extinguisher of Capacity 10 KILOGRAM, consisting of welded Mild Steel Cylindrical Body Squeeze Lever Discharge Valve 300mm long high pressure discharge hose, discharge nozzle, suspension bracket, ISI marked as per IS:13849 finishing Externally with Red Enamel Paint and fixed to Wall with Brackets with Internal Charge, complete all as specified and as directed.

Supply, installation, testing and commissioning refrigerator electric driven single phase capacity 185 litres(± 2%) frost free, single door, BEE five star rated and complete all as specified.

Supply, installation, testing and commissioning refrigerator electric driven single phase capacity 210 litres(± 2%) frost free, single door, BEE five star rated and complete all as specified.

Supply, install, fixing, commissioning and testing of centrifugal pumping set 330LPM capacity at 30m head , suitable for drinking water and coupled with 3 phase, 50 c/s, 415 volts electric motor of suitable capacity including GI 6m length suction pipe, CI foot valve etc. and connecting up with delivery main complete all as specified and as per manufacturer's specifications.

Taking up cast iron sluice valve of 80mm bore complete all as specified and directed.

Taking up or down gate valve any type of upto 50 mm bore.

Taking down existing main switches/DBs etc. of any capacity and any rating.

Taking down old service connection of any size including house services bracketsc. Complete all as specified and as directed.

Supply and fixing standard shock treatment chart laminated written in Hindi, English and local language including necessary pictures as per IES rule complete all as directed.

Supply, laying, jointing and testing of 150mm internal diameter of double wall corrugated(DWC) high density polyethylene pipes (HDPE) and stiffness classes-8 (SN-8) with ISI marked(with CML no) and including all fitting of pipe & jointing material for sewage line and laid in trenches all as specified in IS-16098-2013 part-2 complete all as specified and as directed. Make :- Rex Polyextrusion Pvt Ltd/Jain Irriogation Systems Ltd/ Alom Poly Extrusions Limited Note:- Bedding of pipe shall not be provide in normal condition and CONSTRUCTION METHODS shall be strictly compiled as per clause no A-4 of ANNEX 'A' of IS 16098 part-II

Taking down existing light fitting complete all as specified and directed.

Supply, Install, testing and commissioning indoor type 4 Panel ( comprising of one incoming and 3 outgoing) vacuum circuit breaker of horizontal isolation, horizontal draw out IP protection IP-4X dust proof, vermin proof totally enclosed safety interlocking system electrically & mechanically with and accessories as described here-in-after and including all accessories as specified in para 19.99 of MES SSR part - I as applicable, 2009 and as per manufacturer's recommendation and complete all as per specified and as directed :-

(a) VCB Breaker 400Amp suitable for 11 KV system with rupturing capacity 250MVA 01 No (Incoming) (b) VCB Breaker 400Amp suitable for 11 KV system with rupturing capacity 250MVA-03 Nos (Outgoing). (c) Bus bar 630 Amp 11KV rated of copper PVC insulated-01 Set (d) CT, epoxy cast resin type current transformer having dual ratio 50/5A and 25/5A accuracy class 1.0 for metering core and 5P 10 for protection purpose with VA burden 15 VA-03 Nos for incomer VCB. (e) CT, epoxy cast resin type current transformer having dual ratio 30/5 A and 15/5A accuracy class 1.0 for metering core and 5P 10 for protection purpose with VA burden 15 VA-03 Nos per each outgoing VCB. (f) Fixed type, three phase, copper wounded, potential transformer epoxy cast resin potential having ratio 11KV/110 V having class 1.0 accuracy, 100 VA with HT/LT fuse for incoming VCB & control wiring from this PT to outgoing VCBs. (g) IDMTL Micro processor based numeric relay with combined 3 O/C and 1 E/F with communicable and current measuring facility type-MICOM P111-03 No's for incoming and outgoing VCB's , (h) Master trip relay type VAJH 13 for tripping -03 nos per VCBs, (i) Auxiliary relay type VAA 33 for transformer trip/alarm -02 No's nos per VCBs.

SRI BABUL NATH

MAA BHAGWATI ASSOCIATES

RC Madan

M/S R. K. INDUSTRIES

United Sales Corporation

NARSINGH DEVELOPERS LLP

Jasvit Constructions Private Limited

M.P. Khaitan

TRIVENI CONSTRUCTIONS