PROVN OF SEWAGE PIPELINE FROM BLDG NO T154 AT 3 EME CENTRE LBW06 AND ADDN ALTN TO BLDG NO P 11A AND P 11B AT SI LINES LBW 07 AND CERTAIN SANCTIONED WORKS REV 15 22 27 28 29 30 31 AT BAIRAGARH AND SI LINES UNDER GE BHOPAL

Amount

Note : Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below:-

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in hard/dense soil complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick each layer as in soil complete all as specified and as directed.

M&L for Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

S&F Salt glazed stoneware drain pipes 150 mm bore, grade ‘A’, laid in trenches and jointed as specified complete all as specified and directed.

M&L for Concrete bed to drain pipes 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tasted; in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate complete all as specified and directed.

S&F reinforced concrete pipes, class NP2, 200 mm bore, laid and jointed with collars complete all as specified and directed.

M&L for Concrete bed to drain pipes 200 mm bore including packing under and haunching against the sides of pipes after they are laid and tasted; in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate complete all as specified and directed.

S&F reinforced concrete pipes, class NP2, 300 mm bore, laid and jointed with collars complete all as specified and directed.

M&L for Concrete bed to drain pipes 300 mm bore including packing under and haunching against the sides of pipes after they are laid and tasted; in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 75mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 110mm bore complete all as specified and directed.

S&F PVC (SWR) floor/Nahani trap, plain with CP grating including jointing with solvent cement, dia of outlet 75 mm complete all as specified and directed.

S&F PVC (SWR) branch piece, single, (single 'Y'), equal or unequal with access door and fixed 75 mm bore/dia, complete all as specified and directed.

S&F PVC (SWR) branch piece, single, (single 'Y'), equal or unequal with access door and fixed 110 mm bore/dia, complete all as specified and directed.

S&F PVC (SWR) branch piece, double, (double 'Y'), equal or unequal with access door and fixed 75 mm bore/dia, complete all as specified and directed.

S&F PVC (SWR) branch piece, double, (double 'Y'), equal or unequal with access door and fixed 110 mm bore/dia, complete all as specified and directed.

S&F PVC (SWR) vent cowl, 75mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl, 110mm bore complete all as specified and directed.

M&L for Brick work with fly ash bricks (Modular), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M&L for Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed. (Note:-Reinforcement to be measured separately).

S&F Mild steel TMT bars 6 to 8mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for Brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L for rendering 20mm thick in two coats of 10mm thick each on faces of brick work or concrete surfaces; first coat (rendering coat) in cement mortar 1: 6 and second coat (finishing coat) in cement mortar 1: 4 mixed with water proofing compound (water proofing compound to be measured separately as supply only) and finished fair and even complete all as specified and directed.

Supply only liquid integral water proofing chemicals complete all as specified and directed. [Make; Dr.Fixit Pidiproof LW+ of M/s Pidilite Industries or STP No. 1 (liquid) of M/s STP Ltd]

S&F in repairs Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, white with integral foot rests including provision of cement concrete bedding & ‘P’ or ‘S’ trap complete all as specified and directed. [MAKE:-SOMANY (Cat.No.121115), PRAYAG (Cat No.4055) or equivalent in CERA/PARRYWARE/ HINDWARE as approved by GE.]

S&F Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, white with integral foot rests including provision of cement concrete bedding & ‘P’ or ‘S’ trap complete all as specified and directed. [MAKE:-SOMANY (Cat.No.121115), PRAYAG (Cat No.4055) or equivalent in CERA/PARRYWARE/ HINDWARE as approved by GE.]

S&F in repairs PVC low level flushing cistern 10 litres capacity, ISI marked, white, with all fitting and fixtures including brackets, PVC connection of 450mm long and 32 mm bore PVC flush pipe, complete all as specified and directed. [MAKE:- SOMANY (Cat No.121002), Prayag (Cat No.501 Smart flush cistern) or equivalent in PARRYWARE-SLIMLINE/CERA as approved by GE]

S&F PVC low level flushing cistern 10 litres capacity, ISI marked, white, with all fitting and fixtures including brackets, PVC connection of 450mm long and 32 mm bore PVC flush pipe, complete all as specified and directed. [MAKE:- SOMANY (Cat No.121002), Prayag (Cat No.501 Smart flush cistern) or equivalent in PARRYWARE-SLIMLINE/CERA as approved by GE]

S&F in repairs Vitreous china wash basin, ISI marked, white, flat back, size 550 x 400mm, including CP waste coupling, 32mm dia PVC waste pipe of suitable length, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed. [MAKE:-SOMANY (Cat No.110107) or equivalent in CERA/PARRYWARE /HINDWARE as approved by GE.]

S&F Vitreous china wash basin, ISI marked, white, flat back, size 550 x 400mm, including CP waste coupling, 32mm dia PVC waste pipe of suitable length, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed. [MAKE:-SOMANY (Cat No.110107) or equivalent in CERA/PARRYWARE /HINDWARE as approved by GE.]

S&F in repairs Vitreous china urinal half stall ISI marked, white, with & including chromium plated waste coupling including connections to flush pipe and outgoing pipes complete all as specified and directed. [MAKE:-SOMANY smart / HINDWARE (Cat No.60002 starwhite) or equivalent in CERA/PARRYWARE as approved by GE.]

S&F Vitreous china urinal half stall ISI marked, white, with & including chromium plated waste coupling including connections to flush pipe and outgoing pipes complete all as specified and directed. [MAKE:-SOMANY smart / HINDWARE (Cat No.60002 starwhite) or equivalent in CERA/PARRYWARE as approved by GE.]

S&F in repairs Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8606) or equivalent in JAGUAR/MARC as approved by GE]

S&F Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8606) or equivalent in JAGUAR/MARC as approved by GE]

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8618) or equivalent in JAGUAR/MARC as approved by GE]

S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8618) or equivalent in JAGUAR/MARC as approved by GE]

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description not exceeding 1 Sqm each, complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 2 Sqm each and refixing in the same opening complete all as specified and directed.

Taking up or down steel tubing and connections 15 mm bore, including cleaning (tubings and connections) for refixing or removal to store, complete all as specified and directed.

Taking up or down steel tubing and connections 20 mm bore, including cleaning (tubings and connections) for refixing or removal to store, complete all as specified and directed.

M&L for cutting chase, pinning in making good to facing where required and pointing in cement mortar 1:3 as required, complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 15 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. [MAKE: TATA/ SURYA/ JINDAL/ PRAKASH]

S&F CPVC pipes, SDR 11 and plain CPVC SDR 11, 16 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 20 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. [MAKE: TATA/ SURYA/ JINDAL/ PRAKASH]

S&F Steel water tubes, medium grade, ISI marked, galvanised, 25 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. [MAKE: TATA/ SURYA/ JINDAL/ PRAKASH]

M&L for heavy duty flooring tiles, harsh weather & UV Resistance, high abrasion resistance, MOH Hardness >6, thickness 10 mm thick, area of each tile not less than 0.09 sqm, anti slip type, laid in floors, steps, edges, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tile with & including 15mm thick rendering in CM 1:4 complete all as specified and directed. [MAKE:-JOHNSON ENDURA or equivalent in SOMANY/ KAJARIA/ORIENT as approved by GE]

M&L for vitrified light shade flooring tiles, 10 mm thick (Square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, laid in floors, etc set and jointed in neat cement slurry and pointed in epoxy adhisive (Make :Dr.Fixit or Balendura) to match the colour of tiles with & including 15mm thick rendering in CM 1:4 complete all as specified and directed. [MAKE: SOMANY / KAJARIA / NITCO]

M&L for vitrified light shade tiles, 10 mm thick (Square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, as in vertical surfaces such as skirting, risers to steps, etc set and jointed in neat cement slurry and pointed in epoxy adhisive (Make :Dr.Fixit or Balendura) to match the colour of tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed. [MAKE: SOMANY / KAJARIA / NITCO]

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile not exceeding 0.11 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Glazed ceramic coloured tiles 350mm x 250mm x 7mm thick or 450mm x 350mm x 7mm thick, in vertical surfaces such as skirting, dados and risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed. [MAKE: SOMANY/ KAJARIA/ ORIENT/ JOHNSON]

Roughning of surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, walls, etc, laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding, moulding and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Fixing only tiles of any type over existing floor finishes (any type) with approved tile fixture adhesive, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles/ rubbish off the permises to a distance not exceeding 250m complete all as specified and directed.

M&L for making good under cills and over arches, lintels and bressummers including all pinning where necessary in cement mortor 1:6, complete all as specified and directed.

Supplying, fabricating and fixing powder coated (minimum thickness 50 micron) aluminium sections of required size for door, windows, ventilators frames and shutters and partitions including aluminium hinges of required size jointing cleats, screws sash fasteners, plug for fixing with walls, columns, etc complete all as specified and directed. [MAKE: JINDAL/ AJIT INDIA/ HINDALCO]

S&F Sheet glass 4.8mm thick, ordinary quality and glazing with oil putty/rubber seal in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 100 mm size complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 75 mm size complete all as specified and directed.

S&F Butt hinges, extruded alluminium alloy with galvanised mild steel hinge pin, anodised and fixed, 100 mm size complete all as specified and directed.

S&F 150 mm Aluminium handles, cast type, anodised complete all as specified and directed

S&F 100 mm Aluminium handles, cast type, anodised complete all as specified and directed

S&F 150 mm Aluminium anodised barrel Tower bolts extruded section and fixed complete all as specified and directed

S&F 100 mm Aluminium anodised barrel Tower bolts extruded section and fixed complete all as specified and directed

M&L for factory made second class hardwood glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and directed.

M&L for factory made, second class hardwood 35mm thick plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed.

M&L for Preparing new or previously untreated surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed.

M&L for preparing old painted surfaces of wood and wood based materials of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F 300mm long aluminium alloy anodised Sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed

S&F anodised aluminium fabricated grills for windows, ventilators, complete all as specified and as directed

S&F in repairs wash basin mixture, centre hole, cast copper alloy, screwed down, high pressure, with capstan head, fancy type, chromium plated screwed for iron pipe or for unions 15mm bore, complete all as specified and directed. [MAKE: PRAYAG (Cat.No.7250) or equivalent in MARC/ PLUMBER as approved by GE]

S&F Soap dish, complete all as specified and as directed. [MAKE: JAQUAR (Cat.No.1131N) or equivalent as approved by GE]

S&F Towel ring, complete all as specified and as directed. [MAKE: JAQUAR (Cat.No.1121N) or equivalent as approved by GE]

S&F hand shower (health faucet) with 8mm dia 1.0 mter long flexible tube and wall hook complete all as specified and directed. [MAKE:- Prayag (Cat No.BH-76) or equivalent in JAQUAR/MARC as approved by GE]

S&F Chromium plated grating doom, including jointing with solvent cement, dia of outlet 100 mm complete all as specified and directed.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, etc. including cleaning or refixing or removal to store, complete all as specified and directed.

S&F in repairs Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size:- 914mm x 460mm x 203, bowl size:- 405mm x 354mm x 203mm, including CP waste coupling and 32mm dia PVC waste pipe of suitable length complete all as specified and directed. [MAKE:- Prayag (Cat No.1239D Gloss) or equivalent in NIRALI/BLUE STAR as approved by GE]

S&F in repairs plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminum hinging device complete all as specified and directed. [MAKE:-PRAYAG/SOMANY/CERA/PARRYWARE /HINDWARE]

S&F in repairs tubular towel rail of aluminium anodised, 20mm dia, D type, 60cm long between flanges complete all as specified and directed. [MAKE:- Prayag (Cat No.BA-40) or equivalent in JAQUAR/MARC as approved by GE]

S&F in repairs wall mixture telephonic with crutch for mixing hot & cold water, fancy type, chromium plated, screwed for iron pipe or for unions 15mm bore, with & including hand shower & tube complete all as specified and directed. [MAKE:- Prayag (Wall mixer cat No.7270 or 7370, shower cat no.BH-73) or equivalent in JAQUAR / PLUMBER / MARC as approved by GE]

S&F in repairs vitreous china wash down water closet pan, pedestal pattern, ISI marked, white, including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed. [MAKE:-SOMANY (Cat No.120403 & 120404) or equivalent in CERA/PARRYWARE /HINDWARE as approved by GE.]

S&F Vitreous china wash down water closet pan, pedestal pattern, ISI marked, white, including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed. [MAKE:-SOMANY (Cat No.120403 & 120404) or equivalent in CERA/PARRYWARE /HINDWARE as approved by GE.]

S&F in repairs brass chromium plated shower rose 125 mm size with swivel joints complete all as specified and directed. [MAKE:- Prayag (Cat No.BS-73) or equivalent in JAGUAR/CERA as approve by GE]

S&F Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12.5 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-43) or equivalent in JAGUAR/CERA as approve by GE]

S&F corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf with chromium plated bracket guard and railing 300mm size complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-44) or equivalent in JAGUAR/CERA as approve by GE]

S&F in repairs Toilet paper holder of mild steel Chromium plated ‘D’ type, fixed to walls with chromium plated brass screws complete all as specified and directed. [MAKE:- Prayag (Cat No.BA-48) or equivalent in JAGUAR/CERA as approve by GE]

S&F Jet spray (butterfly) with 1 mtr tube complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-18) or equivalent in JAQUAR / PLUMBER / MARC as approved by GE]

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8602) or equivalent in JAGUAR/MARC as approve by GE]

S&F in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (angle type) screwed both ends for iron pipe or for unions 15mm bore, complete all as specified and directed. [MAKE:- Prayag (Cat No.8610) or equivalent in JAGUAR/MARC as approve by GE]

M&L for second class hardwood plain fillets, square, rectangular in section n. exc 3 sqcm, clean swan, secured with nails and fixed, complete all as specified and directed.

S&F in repairs prelaminated partcle board 9 mm thick, exterior grade, prelaminated both side with decorative choice lamination fixed with screws to timber frame work complete all as specified and directed.

S&F in repairs prelaminated partcle board 19 mm thick, exterior grade, prelaminated both side with decorative choice lamination fixed with screws to timber frame work complete all as specified and directed.

S&F magnetic catches for cupboards with plastic body and striking plate not less than 40mm including fixed in, complete all as specified and directed.

S&F 75mm brass handle, cast type, polished bright, complete all as specified and directed.

S&F 40mm wide flap, continuous piano hinges, brass, bright finish, complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, ceilings, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Preparing new plastered or unplastered surfaces of wall and M&L for applying two coats of distemper oil emulsion, white or tinted over a coat of primer and including 3mm thick wall care putty (Make: Birla/JK) on plastered surfaces complete all as specified and directed.

Preparing new plastered or unplastered surfaces of wall and M&L for applying two coats of exterior acrylic emulsion paint, white or tinted over and including a coat of exterior wall primer on plastered surfaces complete all as specified and directed. [Make :Shalimar(Saktiman) / Asian(ACE) / Burger(wall masta)]

Complete removal of existing treatment and M&L for applying two coats of exterior acrylic emulsion paint, white or tinted over and including a coat of exterior wall primer on plastered surfaces complete all as specified and directed. [Make :Shalimar(Saktiman) / Asian(ACE) / Burger(wall masta)]

Complete removal of existing treatment and M&L for applying two coats of distemper oil emulsion, white or tinted over a coat of primer and including 3mm thick wall care putty (Make: Birla/JK) on plastered surfaces complete all as specified and directed.

M&L for applying 3mm thick wall care putty (Make: Birla/JK) complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

Demolition to cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of brickwork built in cement or cement lime mortar complete all as specified and directed.

S&F Mild steel chromium plated, 19mm dia, minimum thickness 1mm, curtain rod with side fixing brackets, rings & decorative knobs complete all as specified and directed.

Dismantling of AC corrugated / semi corrugated sheet as in roof coverings complete all as specified and directed.

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 Sq cm in section in framed work complete all as specified and directed.

Dismantling timber scantling 40 sq cm and over in section, in any position in unframed work complete all as specified and directed.

S&F Steel work in tubular/structural trusses, purlins, etc including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 or steel sections conforming to Fe 410-W (Gde E-250) quality -A complete all as specified and directed.

S&F Mild steel work conforming to Fe-290 Gde E-165 in wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed., drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JINDAL]

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in ridges, etc, fixed with & including self tapping screws complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JINDAL]

M&L for preparing old painted steel & iron surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed.

S&F Mild steel conforming to Fe-290 Gde E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed trusses complete all as specified and directed.

M&L for Factory made, machine pressed, M-35 grade concrete interlocking paver blocks (glossy /reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 60 mm thickness with & including 50 mm thick stone dust cushion and joints filled with sand complete all as specified and directed. [MAKE:- MEHTAB / NAVYA TILES / SAP PAVERS/ SAGAR TILES]

S&F stainless steel kitchen plate rack overall size- 31" x 36" x 10" duly fixed on walls with gutties & screws of suitable length complete all as specified and directed. [MAKE:- Prayag (Cat No.P-340) or equivalent in NIRALI/BLUE STAR as approved by GE]

M&L for Providing precast reinforced cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in louvers and jallies 35mm thick (measured solid) including all mouldings but excluding frame and set in cement mortar 1:4 complete all as specified and directed.

M&L for preparation of old/new surface and applying two coats of damp proof chemical (Acra coat of make Dr. Fixit) over a coat of cement based white putty, complete all as specified and directed.

Providing and injecting chemical emulsion for post constructional anti termite treatment along the external wall, below concrete or masonryapron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc, complete all as specified and directed.

Providing anti termite treatment of soil under existing floors using emulsion @ one litre per square metre, hole 300mm apart, including drilling and plugging 12 mm dia holes with cement mortor 1:2 to match the existing floor, complete all as specified and directed.

M&L for cutting holes in brick walls exc half brick but n exc one brick in cement mortar for incerting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete type B1, 1:2:4 as required, complete all as specified and directed.

S&F Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, with & including filing of cement concrete typ B-0, 1:2:4 using 12.5mm graded stone aggregates inside frames complete all as specified and directed.

S&F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, with & including filing of cement concrete typ B-0, 1:2:4 using 12.5mm graded stone aggregates inside frames complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 20-25mm thick (size not less than 450mm x 600mm) with and including 20mm thick cement screed base in CM 1:3, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar, etc with and including 10mm thick rendering in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete all as specified and directed.

M&L for non shrink cementious micro concrete for jacketing on surface of columns, beams and similar structural members with 5 to 12mm stone aggregate in the ratio as per manufacturers instructions laid to as thickness, including curing and use and waste of necessary scaffolding as required, complete all as specified and directed.

M&L for galvanised cold rolled steel section framework of size 600 x 600mm grid size using 24x38x0.50 (composite thickness) tee (bottom pre coated) & 24x24x0.50mm (composite thickness) wall angle including suspenders as per manufacturer’s instructions complete all as specified and directed. [Make: GAPSON(Gabsec) or equivalent as approved by GE]

S&F asbestos free calcium silicate board of size 600x600x6mm, fixed to steel frame work in ceiling with & including applying two coats of oil bound distemper complete all as specified & directed. NOTE:- Cost of making frame work for light fittings, etc is deemed to be included in the quoted unit rate

S&F GI frame work size of grid 605 mm x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylong sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two eaqual flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kuled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed

M&L for providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to curved surface for any shunk and raised moulding over GI framework and reinforced with GI wiremesh (fillets and GI wiremesh paid separately), complete all as specified & directed.

S&F readymade decorative POP cornices (as per sample kept in GE office) size exceeding 75mm and not exceeding 125mm fixed on ceilings, etc duly fixed with screws/adhesive complete all as specified and directed.

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets complete all as specified and directed.

M&L for racking out joints/pointing to squared rubble masonry, coursed or uncoursed in cement or cement lime mortor, complete all as specified and directed.

M&L for struck pointing to squared rubble masonry, coursed or uncoursed in cement or cement lime mortor, complete all as specified and directed.

M&L for 75mm thick Cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in leveling course, benching, sub base, complete all as specified and directed.

M&L for 5cm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:3 or cement mortar 1:4, complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1: 4 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement paint white or tinted over & including a coat of cement wash complete all as specified and directed.

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed. [MAKE:-SINTEX/ POLYWELL/ POLYCON/POLYPLAST]

S&F in repairs Ball brass valves, ISI marked, high pressure, with polythene float and fly nut, screwed for iron pipe or brass ferrule 15 mm bore complete all as specified and directed. [MAKE:-SANT / LEADER / RAMCO / ZOLOTO/PRAYAG]

S&F steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.

S&F Figured glass, pin head type 3mm thick and glazing with oil putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers not exc. 15cm thick, spread, levelled and blinded with earth and rammed including watering complete all as specified and directed.

M&L for Hard core of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in columns, pillars, posts & struts complete all as specified and directed.

Use & waste of Form work to sides of square or rectangular columns, pillars, posts and struts for fair finished surfaces of concrete complete all as specified and directed

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Use & waste of Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides & soffits of lintels over 1.5m clear span, floor or roof beams, cantilevers, etc for fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to edges of concrete flats, openings, floors & roofs and sides of RCC/PCC bands in walls and similar work exceeding 5cm but not exceeding 10cm wide for fair finished surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in foundations, footing, plinth beams, bases for columns and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in lintels over 1.5m clear span, beams and cantilevers complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-25 in slabs supported on walls, beams & columns complete all as specified and directed.

M&L for Rendering 10mm thick in cement mortar 1: 3 on faces of ceiling surfaces, finished fair and even complete all as specified and directed.

M&L for preparing new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for 25mm thick Cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate in leveling course, benching, sub base, complete all as specified and directed.

M&L for surface excavation n. exc. 30 cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified and directed.

M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M&L for Water proofing treatment on roof surfaces with APP modified membrane with non woven polyester reinforced, weight not less than 3 KG/SQM and thickness of membrane not less than 3mm having thermal insulation with white mineral/gravel finish on upper side of membrane uniformly embedded during manufacturing process laid in following sequence complete all as specified and directed.:- (a) Applying 10mm thick plaster in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on cleaned roof surface. After properly curing of the plaster, the roof will be tested for water tightening by ponding with water for seven days for any seepage/leakages, etc. If any seepage/leakage is observed the rectification will be carried out by pressure grouting under pressure of 5 Kg/sqcm using cement based grout. After the roof surface is repaired, the slab /roof will be again tested for water tightness before proceeding for further treatment. (b) Properly cleaning and drying of the plastered roof surfaces, parapets, gutters, drain mouths, etc for all foreign matters such as fungus, moss, dust, etc by wire brushing and dusting. Proper grooves shall be cut around CI drain outlets/pipes/chimney pipes and other similar situations to tuck in the treatment. (c) Applying a coat of bituminous primer conforming to IS: 3384-1965 @ 0.3Kg/Sqm on the prepared surface till the surface is properly impregnated. (d) Laying APP modified water proofing membrane with 100mm overlap in longitudinal direction and 100mm overlap in transverse direction sealed and bounded to the surface by torch application method. (e) All joints and changes in direction should be curved with cement mortar 1:3 with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. A fillet of PCC 1:2:4 type B0 using 12.5mm graded stone aggregates shall be provided at all junctions of vertical and horizontal surfaces and wherever there is change of direction. (f) Topping will be done with precast machine pressed 20-22mm thick PCC tiles (using grey cement) of size 250 x 250 mm or 300 x 300mm, conforming to IS-1237 (hydraulically pressed), laid over 15mm thick cement mortar screed in CM (1:4), set & jointed in neat cement. Joints of tiles shall be 2-3mm wide and grouted with chemical ‘Tile Grout’ of M/s Asian Paints or equivalent as approved by GE.

M&L for Second class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets etc. to be measured separately), removing materials to store for keeping in safe custody or for taking credit and making good disturbed surface of walls, floors, etc.complete all as specified and directed.

M&L for point wiring complete for light/fan/exhaust fan on independent / combine with cable 1.50 sqmm (nominal area), FRLS PVC insulated, unsheathed, single core multi-stranded copper conductor cable, 1100 volts grade, ISI marked controlled by one one-way switch, drawn through and including concealed medium grade PVC conduit not less than 20 mm dia, ISI marked, with all accessories (PVC casing and capping of size 25 mm , ISI marked with complete accessories to be used wherever wiring to be run on ceilings and concrete surfaces) including one run of 1.5 sqmm FRLS muti-stranded copper conductor (green colour cable) as earth continuity wire connected to common earth dolly, including sunk sheet steel terminal box made out of 1.20 mm thick and not less than 60 mm in depth GI/MS/ pressed steel terminal box to be concealed in wall, duly painted with two coats of anti corrosive black bituminous paint over a coat of red oxide primer in and out sides and two coated of aluminium paint on internal surface , including laminated hylum sheet cover, ISI marked for mounting of fittings like switches, sockets, fan regulators, etc. fixed with galvanised screw and cup washer complete all as specified and directed. Note : (i) Wiring to be done as per approved colour code in IE rule.(ii) Rate includes chase cutting for concealed wiring. [Make of Cable : Polycab/ Plaza/ Havells]

All as per BOQ item No. 179.00 here-in-before, but for one switch socket combination 5/6 Amp on independent board, complete all as specified and directed.

All as per BOQ item No. 179.00 here-in-before, but for one three pin outlet 5 Amp on same board with other switches, complete all as specified and directed.

All as per BOQ item No. 179.00 here-in-before, but for one switch socket combination 6 pin 5 /15 Amp on independent board with wire of size 2.5 sqmm and 2.5 sqmm as earth wire, complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way, 6 Amps, 240 volt, 50Hz, AC, ISI marked complete all as specified and as directed. [MAKE:-ANCHOR (PENTA series) or equivalent in LEADER/ CRABTREE/LEGRAND/HAVELLS as approved by GE]

S&F Bell push, flush type, 6 Amp piano type, 240 volt, 50Hz, AC, ISI marked complete all as specified and as directed. [MAKE:-ANCHOR (PENTA series) or equivalent in LEADER/ CRABTREE/LEGRAND/HAVELLS as approved by GE]

S&F Switch socket combination 5 pin, type 5/6 Amps flush type, 230 volt AC complete all as specified and directed. MAKE:-ANCHOR (PENTA series) or equivalent in LEADER/ CRABTREE/LEGRAND/HAVELLS as approved by GE

S&F Socket outlet 5 pin 5 Amp flush type, 240 volt AC complete all as specified and as directed. [MAKE:-ANCHOR (PENTA series) or equivalent in LEADER/ CRABTREE/LEGRAND/HAVELLS as approved by GE]

S&F Switch socket combination 6 pin, type 5/15 Amps flush type, 230 volt AC complete all as specified and directed. MAKE:-ANCHOR (PENTA series) or equivalent in LEADER/ CRABTREE/LEGRAND/HAVELLS as approved by GE

S&F Ceiling rose surface bakelite, three terminals, 240V, 50Hz, ISI marked complete all as specified and as directed. [MAKE:-ANCHOR (PENTA series) or equivalent in LEADER/ CRABTREE/LEGRAND/HAVELLS as approved by GE]

S&F Bell, Ding Dong type, electric, single phase, 240 volt, AC complete all as specified and as directed. [MAKE:-ANCHOR (PENTA PC series) or equivalent in LEADER/ CRABTREE/LEGRAND /HAVELLS as approved by GE]

S&F LED tube light fitting, surface mounted lumanaires, 1 x 18 W, 240V, decorative ultra slim round /squar profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack with bipin holders, LED lamps,connector block, etc. complete with all accessories internally pre-wired and including connecting up with flexible copper conductor cable of suitable size complete all as specified and directed. Make : Havells Cat No : LHEXBLP7N1W018 or equivalant in C&G/Bajaj/Wipro/Osram

S&F LED tube light complete fitting, surface mounted lumanaires, 1 x 9 W, 240V. Decorative ultra slim round /squar profile LED lighting fixture with extruded polycarbonate , environmental friendly, energy efficient ready to use pack.with bipin holders, LED lamps,connector block, etc. complete with all accessories internally pre-wired and including connecting up with flexible copper conductor cable with suitable size complete all as specified and directed. (Make : Havells LHEXBLP7IN1W009 or quivalant in C&G/Bajaj/Wipro/Osram)

Refixing of serviceable light fitting any type any make retrieved against item No. 178.00 with connection complete all as specified and directed.

S&F Angle holder, PVC/Poly carbonate type with back plate suitable for batten fittings complete all as spcified and directed. [MAKE FOR HOLDER:-ANCHOR (PENTA PC series)/ LEADER/ CRABTREE/LEGRAND/HAVELLS as approved by GE]

S&F LED lamp 10 watt, B22 CDL complete all as spcified and directed.

S&F building security light fitting 20 W made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC over having top opening separate driver compartment with IP-66 protection and impact resistance of IK07 with suitable galvanised iron pipe 'light grade' brackets 1 mtr length bent to shape to obtained required shape including clamps, nuts, bolts, washers etc. connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and as directed. Make :- Havells Cat No. ENDURAPEARLSL20WLED757SASYTOPCMP/Bajaj/Surya

S&F exhaust fan 300 mm sweep, metal body, complete with louvers incl all civil work like cutting and making circular opening in existing wall of kitchen etc. incl connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified & directed. Make-Havells Model Ventilair DB- NEO or equivalent in CG/Bajaj/Usha

S&F Ceiling fan 1200 mm sweep, 240 V complete with accessories, complete all as specified and as directed. [MAKE: Havells Model Velocity or equivalent in CG/Bajaj/Usha]

S&F fan step regulator, 120 watts, 2 module complete all as specified and directed. (Make:- Legrand (Cat. No.573469) or equivalent in Anchor ROMA DEKO 'D' series / Crabtree)

M&L for sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core PVC insulated FRLS cable 1100V unsheathed with stranded copper conductor of 6.0 sqmm nominal cross section area and drawing into and including concealed 25mm dia, rigid non metallic PVC conduit, ISI marked, medium grade, inclusive of all fittings such as tees, bends, junction boxes, elbows, saddles, pipe hooks, couples, lock outs, etc and PVC insulated stranded copper conductor of 4.0 sqmm nominal cross section area as earth wire complete all as specified and directed. Note: - (i) Two runs of 6.0 sqmm cable, one run of 4.0 sqmm cable of earth continuity conductor & PVC conduit pipe shall be measured as one unit length.(ii) Cutting chases & making good for concealed sub main wiring will be measured and paid sepeartely under susequent item.[Make of Cable : Polycab/ Plaza/ Havells]

Supply and fixing factory made epoxy powder coated Distribution Board TP & N 4 ways ( VTPN MCCB DB ) and space for MCCB as incomer, with metal door ( IP-43 protection ) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including isolated Neutral Bar, Insulated busbar assembly, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts including taking down old DB complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE] NOTE:- MCCB shall be measured and paid seperatly.

S&F of MCCB 4 pole, 415 Volt fixed type, 125 Amp 16kA breaking capacity including taking down old MCCB complete all as specified and directed. Make :- Havells/Indo Asian /L&T.

S&F in replacement sheet metal enclosure double door type surface mounted concealed in wall 8 ways, 240 Volts, ISI marked 200 amps bus bar dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE] NOTE:- MCB shall be measured and paid separately.

S&F in repairs MCB SP, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 5 to 32 amps including connection with suitable size aluminium / copper lugs complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

S&F in repairs MCB SP suitable for 240 volts, AC supply 40 to 63 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

S&F in repairs MCB SPN suitable for 240 volts, AC supply 6 to 32 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA, complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

S & F in repairs MCB SPN suitable for 240 volts, AC supply 40 to 63 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

M&L for Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR-2009 Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by 15mm dia light grade GI pipe and watering pipe shall be 20mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed. NOTE :- (i) The concrete pit shall be PCC (1:3:6) type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) The unit rate includes the cost of GI pipe medium grade for protection of earth wire and 4mm dia earh lead wire upto 7.5 M. (iii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself.

S&F 50mm GI tubing light grade with all fittings as required for passing through cables under floors, along the wall or along the pole, etc with suitable size M.S.flat iron clamps incl nut,bolt and washer including taking down old rusted pipe complete all as specified and directed. [MAKE:-TATA / JINDAL / PRAKASH / SWASTIK as approved by GE]

Supply, laying, connecting and testing LT XLPE insulated, screened, PVC bedded, armoured, heavy duty cable with aluminium conductor of size 25 sqmm, 3.5 core, 1100 volts grade, laid in trenches, passing through pipes/ducts, etc including taking out old unserveciable cable, any type complete all as specified and directed. [MAKE:- POLYCAB /HAVELLS INDIA LTD/V-MARC as approved by GE]

S&F 40mm GI tubing light grade with all fittings as required for passing through cables under floors, along the wall or along the pole, etc with suitable size M.S.flat iron clamps incl nut,bolt and washer including taking down old rusted pipe complete all as specified and directed. [MAKE:-TATA / JINDAL / PRAKASH / SWASTIK as approved by GE]

Supply, laying, connecting and testing LT XLPE insulated, screened, PVC bedded, armoured, heavy duty cable with aluminium conductor of size 10 sqmm, 2 core, 1100 volts grade, laid in trenches, passing through pipes/ducts, etc including taking out old unserveciable cable, any type complete all as specified and directed. [MAKE:- POLYCAB /HAVELLS INDIA LTD/V-MARC as approved by GE]

M&L for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection (8 cm below cable & 15 cm above cable) complete all as specified and directed. [Note:-Compacted/punned thickness shall be measured & paid]

Supplying and laying sub class 'B' bricks (modular) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and directed.

Taking down u/s light fitting any type and S&F LED 20 W/21Watt tube light fitting (T8 type), including LED retrofit tube 20/21 W one side connection type, 240 v, PF > 0.90, colour Temp 6500 K, System Luminious efficacy > 100Lm/W, complete with powder coated CRCA decorative patti suitable for surface mounting on wall, complete fitting including connecting with PVC insulated multistranded copper flexible cable 0.5 sqmm two core, and PVC round block white colour x 2 Nos for mounting of fitting complete all as specified & directed. Make :-Bajaj ( For Batten Model No. BLRB DB 118 or suitable for mounting T8 LED tube 20 watt and For LED tube Model No. BLRB21WCWc) or C&S cat Part No. LTDC01220WLED/WD (LED battan T8 TARA -M) or Havells (Titania LED tube with Regal batten LED) or equivalent in Philips/ Crompton as approved by GE.

S&F LED 9/10Watt tube light fitting, surface mounting fitting for mirror light with slik and light weight batton, 240 Volt, with PF >0.95, efficacy >95 , colour temp 6500K complete fitting including connecting with PVC insulated multistranded copper flexible cable 0.5 sqmm two core and PVC round block white colour x 2 Nos for mounting of fitting complete all as specified & directed. Make :-Havells cat Part No. LHEXBQP7PN1W009 or equivalent in Philips/ Crompton/Bajaj and C&S as approved by GE.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 amps rated busbar, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 including wooden rectangle board of first quality of suitable size for mounting of DB box complete all as specified and directed by Engr-in-charge.Make- Legrand/ Seimens/ Schinder.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 amps rated busbar, 2 way Single door without bus bar, enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 30 including wooden rectangle board of first quality of suitable size for mounting of DB box complete all as specified and directed. Make- Legrand/ Seimens/ Schinder.

S&F PVC fresh air fan of 300 mm sweep in toilets compete with louvers including all civil work like cutting and making opening in existing wall of toilet etc ,including including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make:Havells/CG/Bajaj/Usha.

S&F Gun metal globe or gate valves, 25 mm bore, with iron wheel head, screwed both ends for iron pipe for the following bores including taking out old unserviceable valve complete all as specified and directed. [MAKE:-SANT / LEADER / RAMCO / ZOLOTO as approved by GE]

S&F Gun metal globe or gate valves, 20 mm bore, with iron wheel head, screwed both ends for iron pipe for the following bores including taking out old unserviceable valve complete all as specified and directed. [MAKE:-SANT / LEADER / RAMCO / ZOLOTO as approved by GE]

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed. [MAKE:-SINTEX/ POLYWELL/ POLYCON/POLYPLAST]

S&F PTMT float valve 20 mm bore, high pressure with high density plastic ball, with epoxy coated Aluminium rod screwed for iron pipe and fixed in all as specified and directed. Make- Prayag/ Polytuf or equivalent as approved by GE.

Supply and installation of Water cooler, electric driven (single phase) having approx storage capacity of 120 litre and nominal cooling capacity of 60 litre per hour, three/five star rated, complete all as specified and directed. (Make:- Blue Star/Voltas or equivalent)

Supply and installation of voltage stabilizer for wall mounting, digital automatic operation, single phase naturally air cooled Indoor type & designed for input variation between 130 to 280 volt with output voltage stabilized at 220 Volt with accuracy of +2.5 %, of capacity 4 KVA complete all as specified and directed. (Make:- Venus/Accube/Integ)

All as per BOQ item No. 179.00 here-in-before, but for one switch socket combination 6 pin 5 /15 Amp on independent board with wire of size 4 sqmm and 4 sqmm as earth wire, complete all as specified and directed.

S&F decorative gate light fitting made up of high grade unbreakable polycarbonate material suitable for 20 Watt LED lamp (B22) complete with all accessories internally pre-wired and including mounting pole dia 60 mm connecting up with copper conductor cable complete all as specified and directed. (Make:- Havells cat No LHFOGAE1T11F015 or equivalent in Wipro/ Bajaj/ Osram)

Deduct schedule of credit (calculation will be done off line) Rs. 41340.00

S Balwinder Singh

SHIV SHANKAR MISHRA

NIHAL ENTERPRISES