ADDN/ ALTN TO BLDG NO P-134, 143, 144, 145 AND 146 (SMQs) AT RED QUARTERS AT CHAFB

Amount

M & L for taking down old damaged existing water proofing membrane of any thickness from roof top complete all as specified and directed. Note: All waste materials shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

M & L for taking down cement or cement lime plaster any description on brick or stone walls, over RCC slab ,ceiling etc including raking out joints, hacking for key, scrubbing down with water, etc. including necessary scaffolding all as specified and directed.

M & L for rendering 10 mm thick cement plaster 1:3 with and including water proofing compound @ 3% by weight of cement or as per manufactures instruction on concrete surfaces, finished even and smooth without using extra cement all as specified and directed. (Note : WPC will be measured and paid seperately as supply only under relevant item)

Supply only integral water proofing compound.

M&L for providing cement concrete type B-0 1:2:4 (using 12.5 mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed.

M & L for TPO (Thermoplastic Polyolefin) membrane cleaning the surface and laying of 200GSM Geo textile and cover up with TPO RF 1.2 mm thermoplastic membrane on roof & up to 300 mm of parapets and crumple joint including junction of roof and parapet, welding the seam joints with hot air gun/machine and terminate the corners with extra protection to bear the high wind pressure, TPO be thoroughly tightened with the lower structure using mechanical fastening properly to avoid the corners and seam joint failure. etc as per manufacturer instructions complete all as specified and directed.

M & L for demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including the like laid over cement mortar 1:4, 20 mm thick set and jointed in neat cement slurry and pointed in white cement with pigment to match including grinding and polishing complete all as specified and directed.

M&L for rounding to edges of granite/stone slab such as in steps, cooking platform and other similar situations etc complete all as specified and as directed.

Demolition of unreinforced cement concrete in floors and pavings not exc 15cm thick below or above ground level complete all as specified and directed.

M&L for 75mm thick cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for all as specified and directed.

M & L 100 mm thick cement concrete type B- 2, 1:2:4 (using 40mm graded stone aggregate) in floor finishesh and paving and finishing cement concrete surface even and smooth Without using extra cement complete all as specified and directed.

Demolition of cement concrete reinforced of any description and in any position / any height not otherwise specifically provided for all as specified and directed.

M & L for rendering in CM 1:6, 15 mm thick on fair faces of brick works/ block works or concrete surfaces finished even and smooth without using extra cement all as specified and directed.

M&L for preparing new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparing new plastered surfaces on wall and applying two coats of oil bound distemper over a coat of chalk whiteneing complete all as specified and directed.

M & L for rendering 5 mm thick in cement mortar 1:3,on concrete sufaces as in ceiling/ chajja , finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered on ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparing new plastered surface on ceiling and applying two coats of distemper over a coat of chalk whiteneing complete all as specified and directed.

M & L for rendering 15 mm thick (in two layers 10 mm & 5mm ) cement plaster 1:4 with and including water proofing compound @ 3% by weight of cement or as per manufacturers instruction on stone masonry surface finished even and smooth without using extra cement all as specified and directed. (Note : WPC will be measured and paid seperately as supply only under relevant item)

M&L for preparing new plastered surface of walls and applying two coats of cement based paint over a coat of primer through mechanical means complete all as specified and directed.

M&L complete removal of existing treatment on walls and applying two coats of cement based paint over a coat of primer through mechanical means complete all as specified and directed.

M & L for disconnecting existing tanks, setting aside or lowering (if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in old or new location position, after cleaning repairing and removing all scale dirt and wiping ,drying etc complete capacity exc 500 & n exc 1000 ltr complete all as specified and directed.

S&F in repair ball valves, 25 mm bore high pressure,of PTMT with epoxy coated Aluminium rod& high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S&F triple layered Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I , 500 Ltrs Capacity including dismantling existing 500 Ltr water tanks complete all as specified and directed.

S&F in repairs 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs 25mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed or bedding in CM 1:6 complete all as specified and directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed or bedding in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic tiles coloured of size 450X 300X 7mm thick on vertical surface set and jointed in neat cement slurry and pointed in white or colour cement mixed with pigment to match the shade of the tiles complete all as specified and directed with 10 mm thick rendering in CM 1:4 for laying wall finishes complete all as specified and directed.

M & L for dismantling floor hearth or wall tiling including cement mortor bedding and backing coat plastering of any thickness removing serviceable tiles to store and rubbish off premises etc complete all as specified and directed.

M&L for PCC 1:5:10 Type E-2 (using 40mm graded stone aggregate) as in filling in sunken slab complete all as specified and directed.

Providing 20mm thick cement plaster in cement mortar 1:3 mixed with pidi proof LW or Dr Fixit or equivalent @ 200 ml per 50kg of cement and finish even and smooth surface without using extra cement as water proofing treatment to sunken floor complete all as specified and directed.

M & L for application of two coats of pidifin 2k water proof coating i.e water proof coat of Pidilite @ approx 1.00 Kg per sqm as per manufactures instructions. Note :- (i) The rate includes for preparation of surface treatment and sealing of all joints, cracks, corners and junction of pipes etc and ponding test complete all as specified and directed by Engineer-in-Charge . (ii) PCC filling shall be measured and paid separately. (iii) Water testing of sunken floor shall be carried as per direction of GE & rates quoted for the item shall be deemed inclusive of expenditure incurred for testing.

S&F in repair stainless steel sink with draining board,made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers, waste pipe , cast iron, cantilever bracket , connecting union overall size 915mmX460mm with bowl size 410mm X 330mmX160mm complete all as specified and directed by Engineer-in-Charge .

S&F in repairs vitreous China wash basin, white flat back, size 550x400mm including cutting for and pinning in ends of brackets or stand all as specified and directed.

Supply and fix 15mm pillar tap,cast copper alloy, with capstan head, chromium plated, fancy type screwed down high pressure,with or without lettered "hot" or "cold" with long screwed shank and fly nuts screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F in repairs vitreous china squatting pan Orrisa pattern of size 580 X 440mm white with integral foot rest 'P' trap including connection to trap and flush pipe anti-syphonage pipe etc complete including making good to floor all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan (Pedestal Pattern), White with 'P' or 'S' trap, including provision of fixing bolts and connecting upto drain and flushing pipe etc. complete all as specified and directed.

Supply only plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device all as specified and directed. Note : Fixing is deemed included in item no 40 above.

Supply and fix PVC flushing cistern with flush out valve type,10 ltrs capacity, low level, white with inlet ball valve,float and handle including bracket including flush pipe complete all as specified and directed.

S&F in repair PVC connection pipe 450mm long 15mm dia both end having brass coupling nut and PVC washer complete all as specified and directed by Engr-In Charge.

S & F in repair Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1 m long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. Cera - F8030104 or equivalent.

S&F in repair bib tap, 15mm bore, fancy type with long neck chromium plated with crutch or butterfly handle screwed down for iron pipe or brass ferule complete all as specified and directed.

S&F in repairs 15 mm bore fancy type, chromium plated Stop valves / Angle cock screwed down high pressure with crutch handle screwed both ends for iron pipe or for unions all as specifed and directed.

S&F in repairs 15 mm bore fancy type, chromium plated with long shunk and cup (concealed type) Stop valves / Angle cock screwed down high pressure with crutch handle screwed both ends for iron pipe or for unions all as specifed and directed.

S&F in repair 125mm dia brass chromium plated shower rose including arm with or without swivel joints including fixing to steel pipe or union complete all as specified and directed by Engr-In Charge.

S&F in repair Brass Chromium plated fancy type towel rail, 20mm dia, D type 600mm long between flanges including brass CP brackets complete all as specified and directed by Engr-In Charge.

S&F sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

M & L for taking up or down steel tubing / CPVC pipes and connections, fittings etc including cleaning for refixing or removal to store for 15mm bore complete all as specified and directed.

M & L for refixing old steel tubing/old CPVC pipes 15 mm dia and connections in new or old position (walls, ceiling ,floors etc) complete all as specified and directed.

S&F tubing,medium grade,15mm bore with all fittings fixed to walls and ceiling or laid in floors including cutting through walls and floors etc and making good complete all as specified and directed.

M & L for taking up or down steel tubing / CPVC pipes and connections, fittings etc including cleaning for refixing or removal to store for 20 mm bore complete all as specified and as directed.

M & L for refixing old steel tubing / old CPVC pipes 20 mm bore and connections in new or old position (walls, ceiling ,floors etc) complete all as specified and directed.

S&F tubing,medium grade,20mm bore with all fittings fixed to walls and ceiling or laid in floors including cutting through walls and floors etc and their making good complete all as specified and directed.

M & L for taking up or down steel tubing / CPVC pipes and connections, fittings etc including cleaning for refixing or removal to store for 25 mm bore complete all as specified and as directed.

M & L for refixing old steel tubing/ old CPVC pipes 25 mm bore and connections in new or old position (Walls, ceilng ,floors etc) ( Ground floor to Seventh Floor) complete all as specified and directed.

S&F tubing,medium grade,25mm bore with all fittings fixed to walls and ceiling or laid in floors including cutting through walls and floors etc and their making good complete all as specified and directed.

M & L for cutting chases, pinning in, making good for Stone concete block or slab walls to facing where required and pointing in cement mortor 1:3 to ends or edges of concealed water tubing and similar work including making good cutting n exc 10cm girth complete all as specified and directed.

M & L for dismantling of PVC drain pipes of 75/100/110mm bore, including all fittings, jointed in cement mortar and taking out of trenches, if required and removing from site of work complete all as specified and directed.

S&F PVC (SWR) pipes single socketed 110 mm bore in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F PVC (SWR) pipes single socketed 110 mm bore in any length with rubber ring joints laid in floor complete all as specified and directed.

S&F PVC (SWR) bend with access door 110 mm bore complete all as specified and directed.

S&F PVC (SWR) bend 110 mm bore complete all as specified and directed.

S&F PVC (SWR) double (double Y) branch piece, with access door 110 mm bore.equal or unequal complete all as specified and directed.

S&F PVC (SWR) Branch piece single (Single Y) equal or unequal with access door 110mm bore complete all as specified and directed.

S&F PVC (SWR) 110mm bore vent cowl complete all as specified and directed.

S&F in repair PVC (SWR) floor trap 110 mm dia, plain with grating including jointing with solvent cement complete all as specified and directed by Engr-In Charge.

S&F PVC (SWR) pipes single socketed 75 mm bore in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F PVC (SWR) pipes single socketed 75 mm bore in any length with rubber ring joints laid in floors complete all as specified and directed.

S&F PVC (SWR) 75mm bore bend any radius with access door complete all as specified and directed.

S&F PVC (SWR) 75mm bore bend any radius complete all as specified and directed.

S&F PVC (SWR) Branch piece single (Single Y) equal or unequal with access door 75mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (Single T) equal or unequal with access door 75mm bore complete all as specified and directed.

S&F PVC (SWR) 75mm bore vent cowl complete all as specified and directed.

S&F in repair PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement complete all as specified and directed by Engr-In Charge.

M & L for taking down chowkhats or frames exc 1.5 sqm but n exc 4 sqm (without taking off shutter from the frames) including taking out hold fasts and PCC bed block all as specified and directed by Eng-in-Charge

M & L for taking down chowkhats or frames n.exc 1.5 sqm with shutter(without taking off shutter from the frames) including taking out hold fasts and PCC bed block all as specified and directed by Eng-in-Charge

M & L for taking down chowkhats or frames exc 1.5 sqm but n exc 4 sqm including taking out hold fasts and PCC bed block all as specified and directed by Eng-in-Charge

M & L for taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each all as specified and directed by Eng-in-Charge.

M & L for taking down shutters of any description n. exc 1 Sqm each all as specified and directed by Eng-in-Charge.

M & L for taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each including refixing in the same opening all as specified and directed by Eng-in-Charge

M & L for taking down shutters of any description n. exc 1 Sqm each including refixing in the same opening all as specified and directed by Eng-in-Charge

M & L for 2 nd class wood hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

M&L 2nd class hardwood exc 13 and n exc 25 sq.cm plain fillets, square, rectangular or triangular in section, clean sawn, secured with screws complete all as specified and directed.

S & F prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including cover fillets for kitchen cabinet complete all as specified and directed.

S&F 2nd class hard wood Plain, framed, panelled shutters 35 mm thick (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

S&F 2nd class hard wood glazed skeleton shutter 35 mm thick, open rebated and prepared to receive mesh ,edges of framing plain, chamfered or rounded complete all as specified and directed by Engr-in-Charge.

S&F 2nd class hard wood glazed skeleton shutter 30 mm thick, open rebated and prepared to receive mesh ,edges of framing plain, chamfered or rounded complete all as specified and directed by Engr-in-Charge.

S & F of steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as specified and directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19mm x 19mm MS square tube EPDM rubber gasket weather seal to be provided through out the frame, the profile shall be mitred cut at two corners and jointed by inserted 2mm of 150mm long bracket of 15mm x 15mm MS square tube inside the 19mm x 19mm MS square tube and suitable screwed the door frame shall be fixed to the wall using PVC fasteners, a minimum of 6Nos screws to be provided for each frame complete all as specified and directed by Engr-In-Charge. Note : The quoted rates are deemed to be included for cutting holes, providing concrete for hold fast and making good to the disturbed surfaces.

S & F Factory made solid PVC Moulded door shutter,28 to 30mm thick(stiles),with 2,4 or 6 raised panel design with 2mm thick Moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face ,with particle board core supplying & fixing in frame at site as per specifications & drawing complete all as specified and directed by Engr-In-Charge.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S & F 100 mm long extruded Aluminium alloy anodised Butt hinge with galvanized mild steel hinge pin type C 22 complete all as specified and directed by Engr-In-Charge.

S&F in repair 100 mm long Brass handle, cast type, polished bright complete all as specified and directed by the Engr-in-charge.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engr-In-Charge.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed by Engr-In-Charge.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed by Engr-In-Charge.

S & F 75 mm long extruded Aluminium alloy anodised Butt hinge with galvanized mild steel hinge pin type C 22 complete all as specified and directed by Engr-In-Charge.

S&F 125 mm long Extruded Aluminium alloy handle, fabricated type, anodised complete all as specified and directed by the Engr-in-charge.

S&F 125 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed by the Engr-in-charge.

S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with beads or stainless steel wire staples complete all as specified and as directed by Engr-In-Charge.

S&F in repair stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with beads or stainless steel wire staples complete all as specified and as directed by Engr-In-Charge.

M & L for hacking out old broken glass (any thickness ,size quality or description) from metal frame including punching or drilling out old glazing pins/spring clips glazed with putty and removing materials from site of work all as directed by the Engineer-in-charge.

M & L for hacking out old broken glass (any thickness ,size quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads and removing materials from site of work all as specified and directed by the Engineer-in-charge.

S&F for 4mm thick figured glass pin head type and glazing with oil putty in square not exc. 0.50 sqm in each pane complete all as specified and directed by the Engr-in-charge.

S&F for 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by the Engr-in-charge.

S & F welded steel wire fabric members n exc 4 kg/ Sqm cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9 mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel including necessary scaffolding upto 7 storey, fixed all as specified and directed.

M & L for bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M & L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M & L for preparation of new or previously untreated wood and wood based Surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of pink primer complete all as specified and directed.

M & L for preparation of old painted wood and wood based Surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of Synthetic enamel paint (ordinary tint) complete all as specified and directed.

M & L for preparation of new or previously untreated steel and iron Surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of Synthetic enamel paint (ordinary tint) over a coat of pink primer complete all as specified and directed.

M & L for preparation of old painted steel and iron Surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of Synthetic enamel paint (ordinary tint) complete all as specified and directed.

M & L for removing demolished material ie building material concrete debris of any type etc to a distance of 10 KM or beyond out of premises of metropolitian area including loading, unloading by manually or by mechanical means (JCB) and to be transported through trolley or tipper and stacking at the destination as and when directed by Engr-In-Charge during execution complete all as specified and directed.

M & L for providing precast cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) set in cement mortar 1:6 in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed.

M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, including small tree roots and drain/sewage pipes lines etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out any type of soil complete all as specified and directed.

M & L Cement concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M & L for pre-cast cement concrete block in PCC 1:3:6 type C1(20mm graded aggregate) masonry with solid blocks, exc. 10cm in width and setting in mortar 1:6 complete all as specified and as directed.

M & L for concrete bed to drain pipes of dia 150mm including packing under, and haunching against the sides of pipes after they are laid and tested; in Cement concrete 1:4:8 type D-2 (Using 40 mm graded stone aggregate) complete all as specified and directed.

S & F Reinforced concrete pipes, Bore of pipe in 150mm class NP2, laid and jointed complete with collars complete all as specified and directed.

M & L for cutting in to existing man holes for connecting new drains for internal dia of pipe 150mm, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement mortar 1:2:4 type B1 smooth finished and reforming benching a srequired complete all as directed.

M&L Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with hard/dense soils complete all as specified and directed by Engineer-In-Charge.

M & L preparation of plastered or un plastered old decorated surfaces of walls by brooming down or wih steel wire brushing, scraping down smoke soot's, moulds, moss & efflorescent salts and treating oily and greasy spots & filling holes & cracks with suitable material like white cement or plaster of Paris and applying one coat of white wash including necessary scaffolding up to 6th storey complete all as specified and directed.

M & L preparation of plastered or un plastered old decorated surfaces of ceiling by brooming down or with steel wire brushing, scraping down smoke soot's, moulds, moss & efflorescent salts and treating oily and greasy spots & filling holes & cracks with suitable material like white cement or plaster of Paris and applying one coat of white wash including necessary scaffolding up to 6th storey complete all as specified and directed.

M & L for preparation of old decorated surfaces of wall including plasters, cornices, etc by washing, rubbing down and stopping and applying one coat of oil emulsion distemper complete all as specified and directed.

M & L for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

D NAGI REDDY

B5BUILDING SOLUTIONS

K. VENKATESH NAIDU