PROVISION OF WATCH TOWERS POST GUARD ROOM AND ATTACHED BATHROOM WITH TOILET AT EMERGENCY GATE AT NT POOL AND OTHER SANCTIONED WORK UNDER NOFRA COLABA MUMBAI

Amount

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil, complete all as specified & directed.

M&L for cement concrete 1:4:8, type D-2 , (using 40mm graded stone aggregate) as in foundations, filling and mass concrete, complete all as specified.

M&L for TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified.

M&L for TMT Mild steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified.

Use and Waste of Formwork to sides of concrete foundations, footings, bases of columns and similar work; vertical or to batter

Use and Waste of Formwork to sides of pillars, posts, struts, piers, column sand stanchions

Use and Waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, edges etc. also splays between floors and beams, etc.

M&L for Reinforced cement concrete type B-1 (1:1.5:3) (20mm graded stone aggregate) (nominal mix)as in raft footings , columns, complete.

M&L for Reinforced cement concrete type B-1 (1:1.5:3) (20mm graded stone aggregate) (nominal mix)as in beam complete.

S&F Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. confirming to Fe 410 -W (Gde -E 250 quality A), complete

S&F Structural steel work Fe- 290 E-165 as in Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc.complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut of length exc 22.5 cm & n. exc 30 cm long & dia of bolt 16 to 20 mm.

M&L brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:6, complete all as specified.

M&L for 75 mm thick PCC 1:3:6 type C 2 using 20mm graded crushed stone aggregate as in plinth protection laid in alternate pannels, finished even and smooth without using extra cement.

M & L for Moorum filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering and well ramming all as directed.

M & L for Anti termite treatment Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured).

M & L for Anti termite treatment treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface.

M & L for Anti termite treatment treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

M & L for Anti termite treatment treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

M&L for broken stone / boulders Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified.

M&L for 100mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base complete all as specified.

M&L for light shade coloured vitrified ceramic tiles 10 mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Submission of detailed plan, section, architechural and structural drawing for (a) watch tower post of 8.5m ht on RCC footing and col 0.45m above ground level and above MC stanchions with PPGI Sheet roofing over steel purlin & rafter. (b) Guard room of 3.2 mtr and roof with PPGI Sheet over MC stanchions and Purlin & Rafter. (c) Shed over emergency gate having roof of PPGI sheet on stanchions of MC, purlin and rafter.Design by any structural consultant and duly vetted by any govt institute complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick(square/Rectanglar) area of each tiles exc 0.11 Sqm but n exc 0.18 Sqm in floor including 15 mm thick screed bed or bedding layer for laying floor finishes in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified.

M&L for Machine cut kota stone slab flooring 20-25mm thick over 15mm thick cement screed base in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M & L for Coloured glazed ceramic tiles in vertical surface 450x300x7 / 350x250x7mm thick but as on vertical surfaces such as skirting/dado including 15mm thick backing coat in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for Rendering 15mm thick cement plaster in cement mortor 1:6 on brick or concrete surfaces to be finished even and smooth without using extra cement, complete all as specified.

M&L for Rendering 15mm thick cement plaster in cement mortor 1:4 on brick or concrete surfaces including mixing integral water proofing compound in the proportion of 3 % of cement content and surfaces to be finished even and smooth without using extra cement, complete all as specified.(Note : WPC will be measured and paid seperately)

Supply only integral water proofing compound complete all as specified and directed.

M&L 16 to 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over and including 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding and rounding all as directed.

S & F Factory made single extruded WPC (Wood Ceosetory windows & other Frames/Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive trength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire ardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, with wood free EPS all as per direction of Engineer-In-Charge.

S&F 2nd class HW plain, solid, straight chowkats and frames,wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints. Complete all as specified and directed.

S&F 35mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both side, complete all as specified.

S&F 35mm thick 2nd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. divided in to squares,with plain, chamfered or rounded , mitred and rebated sash bars,any numbers ; edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified ; supplied and fitted to chowkhats , complete all as specified.

S&F powder coated (colour of coating as directed) aluminium (minimum 50 micron thickness of coating) of various section as required/suitable for doors, window & partion/Ventilator (sliding /or openable type,)etc including fixing and making the frames hinges to receive glass/wire gauge etc. Complete incl all fittings like jointing cleats, glazing clips, rubber neoprene packing. anodised aluminium snap beading screws etc. rubber beading, clips locking arrangement, handle, sealant etc all as specified and as directed.

S&F powder coated aluminium grill with and including suitable aluminium anodised frame F/H section as requird manufactured by Approved make as per design No DG- 104, 7.5 mm thick all as specified and as directed by Engr- in- charge.

S&F 3mm thick sheet glass froasted or obscured one side and glazing with new wooden beads/ aluminium beads in square all as directed.

S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples all as specified and directed.

M&L for preparation of newly wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer incl preparation of surfaces.

S&F 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts all as specified.

S&F for aluminium anodized barrel tower bolts 200 mm of extruded section all as specified and directed.

S&F for aluminium anodized barrel tower bolts 150 mm of extruded section all as specified and directed

S&F 150 mm size aluminium alloy handles, cast type anodised, ISI marked all as specified.

S&F butt hinges 100 mm stainless steel hinges medium weight and fixed.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring all as specified

M&L for cement concrete 1:2:4 type B-1 (20 mm graded stone agg) as in , bed plates etc all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat primer on 2 mm thick wall care putty all as specified and directed.

M&L for Preparation of new plastered surfaces of wall and apply two coats of Acrylic emulsion exterior paint of required shade over a coat of primer complete all as specified.[NOTE-Scaffolding deemed to be included in quoted rate,Necessary safety precautions need to be taken.]

S&F rolled sections as in main & cross beams , columns, hip and jack rafters , purlins where connected to common rafters and running rails,wind ties & any other places with angles cleats ot other connected plates confirming to Fe 410 -W (Gde-E-250) quality A, complete all as specified.

S&F plates (plain or chequered ) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attahment, confirming to Fe 410 -W (Gde-E-250) quality A, complete all as specified.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F Plain galvanised mild steel sheeting 1.25 mm thick in ridges hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 and opening for rain water pipe to be provided fixed with MS Flat complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed,in any length with rubber ring joints, fixed to wall including GI clamps of approved shade and complete all as specified and directed.

M&L for false ceiling made out of 600x600x 4 to 6 mm thick ceiliing board / tiles deep panel suspensor system made out of powder coated GI sheet main tee of size 23.50x40x0.63mm and cross tee of size 23.50x23.50x0.63mm and angle size 19x19x0.63mm including 3mm GI wire for suspending bolts necessary washers nut/clits/pin hook etc. for securing frame work to ceiling to the snap grid all as directed by Engr-in-charge including provn of necessary holes / cuttings for providing light/fan as required including making necessary recesses / projected pattern complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of newly steel surfaces of any description and applying two coats of synthetic enamel paint over a coat of red oxide incl preparation of surfaces.

M&L for complete removal of old decorated surfaces of walls by scrapping old paint with steel wire brush, wash the surface throughly and applying two coats of acrylic emulsion exterior grade (100%) (1st coat shall be applied by brush/roller, 2nd coat shall be applied by using spray machine over a coat of primer complete including necessary steel scaffolding + green cloth all round the work side for any posititon/height, complete all as specified and directed.(For bldg upto GF to max of 16th Floor + upto height of mummty top ). [Note-Scaffolding deemed to be included in quoted rate,Necessary safety precautions need to be taken.]

S&F fancy two way bib taps, chromium finish, screwed down, & fixed complete all as specified and as directed.

S&F in aluminium anodised tubular towel rail 20mm dia 600mm long including necessary aluminium brackets complete all as specified and as directed.

S&F PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F moulded polythylene water storage loft tank tank of 300 ltr capacity hoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for inron pipe and fixed (minimum weight 210 grms ) all as specified and derected.

S&F in repairs PVC modular section 20mm thick as in profile including 'C' channels, aluminium all around the profile all as specified.

S & F stop valve /angle valve fancy type chromium plated screwed down, high presure with butterfly handle screwed both ends for pipe and fixed to pipe of 15mm dia bore complete all as specified and as directed.

S&F water closet squatting pan (Orissa pattern) 580x440mm, white with integral foot rests including connecting to trap and to flushing pipe antisyphonage pipe including making good to floor (excluding flushing cistern and flush pipe).

S&F 10 ltr capacity PVC syphonic action type flushing cistern low level white with inlet, ball valve, float and handle including connetion to pipe but fixed in repair complete all as specified.

S&F Vitreous china wash hand basin flat back of size 550x400mm including bracket, brass chromium plated waste coupling of 32 mm bore and pillar tap 15mm bore dia fancy type complete as fixed in repair.

S&F Cast iron work grade FG 150, machined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles machined each exceeding 5 Kg by weight complete all as specified and directed by EIC

S&F Cast iron cowl suitable for 75mm dia pipe , complete all as specified.

S&F Cast iron cowl suitable for 100mm dia pipe, complete all as specified.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors including fixing clips, bends, elbows, shoes etc complete all as specified and directed.

S&F PVC (SWR) bends of 110 mm bore complete all as specified.

S&F brass chromium plated shower rose 125mm size, including fixed to steel tube, complete all as specified.

S & F Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms)

M&L 75mm cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) including complete all as specified and as directed.

S&F 100mm CI ‘P’ or ‘S’ Traps jointed with neat cement paste fixed to wall or roof at any floor/ any height/ any location including all fittings complete all as specified and as directed by Engr-in-Charge.

S&F 100 mm bore of sand cast Cast iron soil waste pipe in any length with ears and jointed with cement joints, laid in trenches ot in floors complete all as specified.

S&F 75mm bore of sand cast Cast iron soil waste pipe in any length with ears and jointed with cement joints, laid in trenches ot in floors complete all as specified.

S&F 100mm CI bends (any radius) diminishing pieces or tapers (larger bore measured).

S&F 75mm CI bends (any radius) diminishing pieces or tapers (larger bore measured).

S&F 20mm bore steel water tubes, medium grade, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors

S&F 15mm bore steel water tubes, medium grade, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors

S&F 20mm bore of dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F for 200mm bore RCC pipe class NP-2 laid and jointed complete with collers as specified including testing all as specified and directed by Engineer-in-Charge.

M&L for cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in bed to drain pipes including forming cradle after they are laid and tested for 300mm bore RCC pipe complete all as specified and as directed by Engineer-in-Charge.

M & L for Cutting into existing manholes for connecting new drain making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 Sec) in cement concrete 1:2;4 type B1 smooth finished and reforming benching as reqd for 200mm bore of pipe.

M&L, Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi-tred/stopped ends etc.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in Hard / dense soil, complete all as specified.

Removal of excavated soils from site to distance exc1.50 Km but not exc 5 Km and depositing where directed, complete all as specified.

S & F Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; tank supports, framed balusters; railing;frame work for water tanks and similar work conforming to Fe 290 Gd E-165 all as specified .

Surface excacation n.exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed

Removing excavated material n. exc. 50m and n.exc 250m depositing where directed at a level n. exc.1.5 m above the starting point complete all as specified and directed

M&L for Sand filling under floors or in foundation including watering and consolidation all as specified and as directed[Note: punned thickness of sand shall be measured and paid]

M&L for Machine pressed precast concrete interlocking paver block with Grey cement and pigment any shape and size 60 mm thick confirming to IS 15658-2006 made of M35 grade concrete complete all as specified and directed by eng-in-chrge.

Demolition of brick work/stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work and pre-cast concrete articles all as specified.

M&L for Rendering 20mm thick on fair face of brick work or concrete in two coats (15mm+5mm) thick cement mortar (1:4) at any height including necessary scaffolding complete all as specified and as directed by Engineer-in-Charge. [Note:-Scaffolding deemed to be included in quoted rate,Necessary safety precautions need to be taken]

Demolition of Cement concrete in any description and in any position not other wise specifically provided directed by Engineer-in-Charge and removal of debris to out side MD land.

M&L for PCC B2 1:2:4 100 mm thick (using 40mm stone aggregate) for floor finishes complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2 type (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Taking down Cast iron/AC/PVC of any dia and size fixed on wall or floor at any floor/ any height/ any location including all fittings complete all as specified.

S&F 100 mm dia sand cast CI soil waste pipe in any length with ears and jointed with neat cement paste fixed to wall at any floor/ any height/ any location including all fittings complete all as specified and as directed by Engr-in-Charge

S&F in repair 100 mm dia sand cast CI bend of any radius with ovel access door and jointed with neat cement paste fixed to wall or roof at any floor/ any height/ any location including all fittings complete all as specified and as directed by Engr-in-Charge

S&F in repair 100 mm dia CI sand cast branch piece single branch of any radius with ovel access door and jointed with neat cement paste fixed to wall or roof at any floor/ any height/ any location including all fittings complete all as specified and as directed by Engr-in-Charge

S&F in repair 100 mm dia branch piece double (equal or unequal) ordinary or inverted or with parallel brach and jointed with neat cement paste fixed to wall or roof at any floor/ any height/ any location including all fittings complete all as specified and as directed by Engr-in-Charge

S&F 160mm dia PVC (SWR) pipes single socketed,in any length with rubber ring joints, fixed in wall including GI clamps of approved shape and size approved by GE at any height, any location, any floor including necessary scaffolding complete all as specified and as directed by Engineer-in-Charge.

S&F 160mm dia PVC (SWR) bends/shoes any radius fixed to pipe at any location/height including necessary scaffolding etc complete all as specified and as directed by Engineer-in-Charge.

M&L for framed brackets of angles, joist, channel, angle or tee sections fixed independently without connecting plates ect cut to shape (cut to ordinary length i.e within 20mm of the length indicated) drilled and cuntersunk for screws, including bending and welding as necessary, confirming to fe-410-0 or fe 310-0 including including cutting holes and making after fixing of bracket and removing of old brackets and remove to store complete as specified and directed.

M & L for Point wiring complete with 1.5 sqmm single core multistranded FRLS PVC insulated sheathed copper conductors 1100 volts grade drawn through & including PVC casing caping ISI marked with accessories on wall/ceiling/truss including cutting chases, pinning in etc with PVC non metallic ISI marked terminal boxes concealed wall including one FRLS PVC insulated & sheathed multistranded green colour copper conductor 1.5 sqmm as earth continuity conductor connected to common earth as earth dolly for the following :-

(a) One light point controlled by one switch SP one way.

(b) One ceiling fan point controlled with one 5A switch

(c) One exhaust fan point controlled with one 5A switch

(d) One 3 pin socket outlet 5Amps on independant board.

(e) One 3 pin socket outlet 5Amps on same board with other switches.

Material and Labour point wiring for 15 Amps socket complete with 2.5 sqmm single core multistranded FRLS PVC insulated unsheathed copper conductors 1100 volts grade drawn through and including PVC non-metallic concealed coduit including PVC bend, tee joints etc as per site requirement, ISI marked with accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI marked terminal boxes / modular boxes surfacing on wall including one FRLS PVC insulated & unsheathed multistranded green colour copper conductor 4 sqmm as earth continuity conductor connected to common earth as earth dolly.

S&F Modular Switch , 6Amp, One way, 1 module, ISI marked.

S&F Modular Switch , 16Amp, One way, 1 module, ISI marked.

S&F Modular Socket , 6 Amps, 2/3 pin combined 2 module, ISI marked.

S&F Modular Socket , 16Amps, 6 pin combined 2 module, ISI marked.

S&F Modular type, electronic fan regulator ( 5 step ), 120 Watts, 230 volts, 2 module, ISI marked.

S&F ceiling rose surface bakelite with ISI mark, flush type with ISI mark three terminals complete all as specified and directed.

S&F Modular white cover plate with Frame 4 Module, ISI marked.

S&F Modular white cover plate with Frame 6 Module, ISI marked.

S&F Modular white cover plate with Frame 8 Module, ISI marked.

S&F Modular metal flush box 4 module, ISI marked and incluing cutting hole in wall / ceiling/piller etc and making good surface.

S&F Modular metal flush box 6 module, ISI marked and incluing cutting hole in wall / ceiling/piller etc and making good surface.

S&F Modular metal flush box 8 module , ISI marked and incluing cutting hole in wall / ceiling/piller etc and making good surface.

Supply and fixing LED lights fitting 1x 18W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing exhaust fan , steel body AC single phase, 230 volt of size 250 / 300 mm sweep 1200 RPM with blades, and frame and louvers complere fixing arrangements on the wall with nuts and bolts making the good surfces all as specifed and directed at site.

Supply and fixing ceiling fans complete with blades, down rods with sefty GI wire connecting up to fan hook, electronic regulaor and accessories , 230 volts , 1200 sweep. Min air delivery 210 CFM with wervice value 6.0 BEE. Five star rated with brushles diret current motor and connectding jup including provision of flexible 3 core copper cable.

Supply & fix MCB DB SPN 12 ways 415 volts with sheet metal enclosures and 200 Amps rated bus bars double door type suitable for MCB's.

MCB SPN 63 Amps, 10 KA rupturing capacity

MCB SP 32 Amps, 10 KA rupturing capacity

Supply & fix 25mm dia bore steel water tubes, medium grade, galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors

Supply & fix 40 mm dia bore steel water tubes, medium grade, galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors

S&F Gun-metal, globe or gate valves 25mm, with iron wheel head, screwed both ends for iron pipe and fixed.

Supply, laying and testing cable Insulated, screened, pvc bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 voltsgrade with stranded aluminium conductor of size 16.0 Sqmm 4.0 core.

Supply and fixing LED flood light 120 watt 230 VAC outdoor type with thermal management inmultiple optics and equipped with IP66protection, with impact and corrosion resistantcomplete with driver and lamp.

Material & labour for for stand post made of mild steel angle of size 50 x 50 x 6mm and mild steel on top of thickness 6mm complete with drilling welding nuts bolts and washer for fixing of search light including painting with synthetic enammeld paint as per Engineer-in-Charge norms over one coat of red oxide primer all as specified and directed by Engineer-in-Charge.

Supply & fix LED type security search light for 2000 Watt with stand fitting as per approved make (marine search light) weather proof cromium plated brass body, wheel house arrangements for both vertical and horizontal direction made out of brass sheet complete with heat resistant toughned glass with hot air scape arrangement with LED lamp provided on security watch tower situted along the perimeter of wall and area all as specified and directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60×60cm.×6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth strip 25 x 4 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed by Engineer-in-Charge.

M&L Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required GI strips 25 x 4 mm complete all as specified and directed.

S&F HDPE of Pressure rating 6kg/cm sq pipe of 40 mm dia including necessary bends,elbows,Tees etc on cable protection complete all as directed.

M&L for rerouting of existing underground GI pipe line up to 1.5 mtr depth of 50 mm to 80 mm dia including welding, cutting laying, jointing etc complete all as specified and directed by Engr in Charge.

M&L for rerouting of existing underground LT cable 50 sqmm to 70 sqmm including jointing material and excavation etc complete all as specified and directed by Engr in Charge.

M&L for GI pipe 50 mm to 80 mm dia medium grade as per site requirement incorporated in item No 140 including connected accessories complete all as specified and directed by Engr in Charge.

S&F XLPE armoured cable 50 sqmm 3.5 core to 70 sqmm 3.5 core, 1100 volt grade as per site requirement incorporated in item no 141 including jointing material, thimble, lugs etc complete all as specified and directed by Engr in Charge.

satguruenterprises (BID ID -3108121)

SHREE JAGDISH FURNITURE CO. (BID ID -3120632)