SPL REPAIR TO BLDG NO MOR 244 TO 247 AT RWA 07 AT NEW MIL STN UNDER GE GANGTOK

Amount

Demolition to cement concrete (un-reinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition Stone slabs and tiles (laid, bedded and pointed in mortar) of any description or thickness in floors, aprons etc complete all as specified and as directed.

Dismantling old PGI/CGI sheeting any gauge, thickness, including Nainital. Sikkim or similar pattern roof/facia etc complete all as specified and as directed.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc including raking out joints, hackig for key,scrubbing down with water in cement or cement lime plaster any description complete all as specified and as directed.

Taking down chowkats or frames n.exc 1.5 Sqm (without taking off shutter from the frames) and removal from site complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm not exc 4.0 Sqm each complete all as specified and as directed.

All as per item No 8 above but openable/fix type window/ventilator complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C2 (using 40mm graded crushed stone agg) as in plinth protection/Path/hardstanding finished the concrete surfaces even and smooth without using extra cement etc complete all as specified and directed.

M&L for Lacquer coated coloured chequered cement concrete tiles of size 200mm x200mm x 25 mm/ 300 x 300mm x 25mm thick as in floor, set and jointed in neat cement slurry and pointed with grey cement and pigment laid over and including screed bed/bedding layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7mm to 8 mm thick (square/rectangular) area of each tile exceeding 0.11Sqm, but not exceeding 0.18 Sqm , in floors over and including 15mm thick screed in CM (1:6) etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified and as directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matc, over and including 15mm thick screed in CM (1:6) etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified and as directed.

M&L for glazed coloured ceramic tiles ( 350 x 450 mm x 7 mm) as in skirting/dado over & including 10 mm th rendering in CM (1:4) set & jointed in neat cement sullry & pointed in white or coloured cement to match complete all as specified and as directed.

Ditto all as item No 14 above but on vertical surface of wall like skerting/dado etc on 15mm thick rendering in CM (1:4) complete all as specified and as directed.

M & L for Granite 18 to 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 15mm thick screed in CM (1:6) etc complete all as specified and as directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and directed by the Engr-in-Charge.

Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheets of any colour having tensile strength of 550 Mpa as in ridges, valley, eaves, etc fixed with self tapping screws complete all as specified and directed by the Engr-in-Charge

S&F powder coated GI grid frame work for false ceiling comprising of the following sections for making partitions of 600 x 600m size fixed to walls with rawl plugs & screws and hanged to roof with and including 1mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 28mm x 23mm x 0.3mm thick, cross tee shall be 24mm x 23mm x 0.3mm thick and wall angle shall be 20mm x 20mm x 0.3mm thick complete all as specified and as directed.

Supply and fix 4mm thick Non asbestos fibre cement building boards (E-board) of approved texture, for insulation and acoustic purpose of size 595 x 595 mm size fixed with staples on snap grid as in ceiling with and including dusting of surfaces and applying two coats of oil emulsion diatemper over a coat of primer including preparation of surfaces complete all as specified and as directed.

M&L for rendering 15mm thick on stone masonary and other than fair faces of brick work surfaces in cement mortar (1:6) finished even & fair complete all as specified and as directed.

M&L for rendering 20mm thick in cement mortar (1:4) in two layers of 10mm each using WPC in finishing layer on brick or concrete surfaces finished even & fair (WPC for finishing layer will be paid seperately as supply only) complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls applying two coats of distemper, oil emulsion, white or tinted over new wall suface on a coat of 3mm thick wall care putty in two layers (1.5mm each layer), complete all as specified and directed.

M&L for applying two coats of white wash on old plastered wall surface including preparation of old surfaces of wall complete all as specified and directed .

M&L for finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified and directed.

M&L for finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) on old plasterd surface incl removal of existing surfaces etc complete all as specified and directed.

M&L for preparation of complete removal of existing treatement on old plastered surfaces of walls applying two coats of distemper, oil emulsion, white or tinted over old wall surface on a coat of 3mm thick wall care putty in two layers (1.5mm each layer), complete all as specified and directed.

M & L for extra forming fair finished drain or channel 30 cm inner girth in cement concerte, using ex- tred/ stopped end etc as specifed and directed.

S & F factory made solid panel wood grain finished PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded wood grain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, panelling of wood grain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR-2004 Part - II,complete all as specified and as directed.

S & F Solid PVC door frame of size 50 mmx 47mm made out of 5 mm wood grain colour PVC sheet reiforced with MS square tube and fixing in opening as per manufacturer instruction complete all as specified and as directed.

S&F 100 mm mild steel butt hinges medium weight,cold rolled complete all as specified and as directed.

S&F 100 mm Aluminum anodised handle and fixed complete all as specified and directed.

S&F 100 mm Aluminum anodised barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F in repair Water Closet (squatt pattern) of vitruous china squatting pan of pattern "ORRISA" pattern size 580 x 440 mm white with integral foot rests (excluding flushing cirstern and flush pipe) including connection to trap and flushing pipe anti syphon pipe etc complete including trap set in and incl concrete complete all as specified and directed.

Supply and fix in repairs Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; brackets, flush pipe, grating and Union for discharge pipe alongwith Urinal spreader of CP any colour for fixing with 15 mm dia pipe (Minimum weight 60gms) complete all as specified and as directed.

S&F in repairs vitreous china, white colour, flat back, wash hand basin of size 55 x 40 x 79cm fixed with brackets , including providing 32 mm dia PVC waste pipe , 32 mm bore CP waste coupling and making all necessary connections complete all as specified and as directed.

S&F in repairs of PVC low level flushing cistern, 10 ltr capacity, syphonic action type white body with inlet ball valve, float , handle, bracket, flush pipe etc & connecting to WC complete all as specified and as directed.

S&F in repairs CP Soap dish, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

M&L in repairs for CI Nahani trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1(diameter of outlet 100mm) as in repair all as specified and as directed.

S&F CP Toilet paper holder fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed.

S&F in repair of PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

S&F in repairs CP health facet of premium quality including two way bib cock and PVC telephonic flexible tube fixed to 15mm bore pipe complete all as specified and as directed.

S&F in repairs bib taps 15mm bore fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs 15 mm bore stop cock, cast copper alloy, chromium plated with long shank and cut screwed down, screwed for iron pipe or union and fixed in repair complete as specified and directed.

S&F in repair chromium plated wall mixer 15mm bore with 115mm long bend pipe for connection to over head shower (with Bush & piston diverter fittings) with aerator screwed down for 15mm bore GI Pipe or for brass ferrul ecomplete all as specified and as directed.

S&F in repair Brass CP mixer for mixing hot & cold water for sink screwed down for iron pipe and fixed complete all as specified and as directed.

S&F in repairs stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repairs corner glass shelf 225x 225mm with CP steel frame complete all as specified and directed, complete all as specified and as directed.

S&F in repairs Chromium plated shower rose 125 mm size with or without swivel joints,including fixing to steel pipe or union complete all as specified and as directed.

S&F in repairs stainless steel plate rack of 1mm thick and size 910x1000mmx250mm three tier complete all as specified and directed.

Taking down 20mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as specified and as directed.

Taking down 25mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as specified and as directed.

Supplying and laying of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified etc complete all as directed by the Engr-in-Charge.

S&F galvanised steel water tubing 25 mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

Cutting chases, pinning in, making good to facing where required and pointing in CM (1:3) for concealed water tubing conduit wiring etc and making good, cutting n.exc 10cm girth as in stone or concrete block walls.

M&L for second class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded on chamfered put together with glue pinned and joints complete all as specified and as directed.

S&F 2nd class hard wood, 35mm thick plain framed, panalled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part-I) complete all as specified and as directed.

S&F 250mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section complete all as specified and as directed.

S&F of 150mm size aluminium handle cast type,anodised complete all as specified and as directed.

S&F of 150mm long aluminium anodised,barrel tower bolt of extruded section complete all as specified and as directed.

S&F in repairs stain less steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F in repairs 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screw as in cup boards ,shelves, shutter etc complete all as specified and as directed.

S&F Continuous (piano) hinges, brass, Width of flaps (when open) in 30 mm bright finish or electrogalvanised etc complete all as specified and as directed.

S&F in repairs CP tubular towel rail 20mm dia D tupe 60cm long complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats paint over one coat of pink primer complete all as specified and directed.

M&L for in repairs Flush shutters 25mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides one face is covered with deco rative face veneer with lipping/frame to match complete all as specified and as directed.

S&F 75 mm mild steel butt hinges medium weight,cold rolled complete all as specified.

M&L for preparation of old painted surfaces of any description over 10cm width or girth of wood and wood based surfaces and applying one coat of synthetic enamel paint (1st graded quality) complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store etc complete all as specified and as directed.

S&F in Repair 75 mm dia PVC floor trap of outlet, with gratings, including jointing to waste pipe fixed in PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) complete all as specified and as directed.

S&F 110mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or under floors , fixed on walls with necessary clips complete all as specified and as directed.

S&F in repairs 110 mm bore PVC (SWR) bend of any radius for PVC (SWR) pipes, fixed to walls or fixed to steel gutter complete all as specified and as directed.

S&F in repairs 110 mm bore PVC (SWR) junction single,(Single T) equal or unequal complete all as specified and as directed.

S&F 75mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed on walls with necessary clamps etc complete all as specified and as directed.

S&F in repairs 75mm bore PVC (SWR) bend of any radius for PVC (SWR) pipes, fixed to walls complete all as specified and as directed.

S&F in repair 110 mm bore PVC (SWR) vent cowl fixed in position complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) junction single,(Single T) equal or unequal complete all as specified and as directed.

E/M Taking down carefully copper/aluminium point wiring (light, fan,socket or power) complete (including fittings such as switches, ceiling roses, pendants, regulatos, sockets ,light fittings etc ), removingb material to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperetel) and making good disturbed surfaces of walls, floors etc to match with existing surfaces.

Taking down unserviceable submain wiring of any size two single core including earth wire and pvc conduit /casing capping and removing materials on site and making good the surface of walls etc complete all as specified and as directed.

Taking down unserviceable distribution board or indoor panel of any capacity including wooden board and making good the disturbed surfaces of wall, etc including two coats of white /colour washing /distempering etc to match the existing complete all as specified and as directed.

All as per item Sl. No. 84 here in before but One 3 pin 5 amps switch socket outlet point on independent board complete all as specified and as directed.

All as per item Sl. No. 84 here in before but One 3 pin socket outlet 5 amps on the same board with other switches complete all as specified and as directed.

All as per item Sl. No. 84 here in before but One bell/buzzer point controlled by one push button on the same board with other switches or independent complete all as specified and as directed.

All as per item Sl. No. 84 here in before but wiring with 2.5 sq.mm multistranded cable and earth wire with copper conductor complete all as specified and as directed.

All as per item Sl. No. 84 here in before but wiring with 4 sq.mm multistranded cable and earth wire with copper conductor of size 4 sq.mm for Metal clad socket complete all as specified and as directed.

Supply and fix Modular switch 1 way 6 A,1 module 230 Volts,50Hz, ISI marked complete all as specified and as directed.

Supply and fix Socket, 6A-2/3 pin combined 2 module 230 Volts,50Hz, ISI marked complete all as specified and as directed.

Supply and fix Modular bell push 6 A,1 module 230 Volts,50Hz, ISI marked complete all as specified and as directed.

Supply and fix Modular switch 1 way 16 A,1 module 230 Volts,50Hz, ISI marked complete all as specified and as directed.

Supply and fix Socket, 6A/16A-2/3 pin combined 2 module 230 Volts,50Hz, ISI marked complete all as specified and as directed.

Supply & fixing LED lights fitting 1x18 watt 220 V, with driver , holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply & fixing LED wall light 1x20watt 220 V, wall light holder with LED bulb suitable for 20 W LED lamp B22 base connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply & fixing LED lights fitting 1x9 /1x10 W 220 V, AC bulk head luminaries including , holder including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply & fixing LED Mirror lights light fitting with high out put diffuser 2 feet , 10 watt 220 v AC decorative type with driver holder and LED lamp including connecting up with driver three core flexible copper conductor cases suitable size complete all as specified and as directed.

S&F ceiling rose, 3 phase ,PVC polycarbonate ,insulated body (ISI Marked) complete all as specified and directed.

Supply & fix lamp holder angular/straight insulated body, with 15 Watt LED bulb , white/ivory finish complete all as specified and as directed.

S&F in repairs round shape 18 watt 220 volts warm / cool type AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size as per site requirement complete all as specified and as directed.

Supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter , voltage 230 v ,50 hz RPM 1200, copper winding of sweep 250 mm complete with all accessories as specified and as directed.

Taking down and refixing of Geysers storage type after complition of civil work 25/50 ltrs capacity complete with grounding/drilling in wall and Provn of Zinc coated fastner 12 mm dia 150 mm long x04 Nos including replace hot & cold PVC pipe complete including nuts/bolt, painting and checking inspection of functionality of element , thermostat, leakge of water assembly , inner tank etccomplete testing all as specified & directed

S&F in repairs heating element 2000 watt ush/screw/triangular/square type suitable for 25 ltrs capacity geysersany complete all as specified and as directed.

S&F in repairs Thermostat switch suitable for 25/50 ltrs capacity geysersof any make /type with temperature rangeadjustable from 25 to 90 degree centigrade heating element 2000 watt ush/screw/triangular/square type suitable for 25 ltrs capacity geysersany complete all as specified and as directed.

Supply & fixing Buzzer Ding Dong AC 230 volts single pole with suitable fixing arrangement complete with all as accessories all as specified and as directed.

S&F single pole & neutral enclosure with a two pin & earth plug & socket complete with one single pole MCB C curve of 20 A rating complete all as specified and directed

M&L for concealed sub-main wiring along with earth wire of size e 2x06 sqmm with 1x6 sqmm earth wire ,ISI marked FRLS ,PVC insulated ,multi stranded , copper conductor ,single core cable drawn through and incl PVC rigid conduit (medium grade) size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduit & sinking for sunken boxes & making good to walls, floors etc complete all as specified and directed

S&F for MCB DB TPN 4 ways Double Door 240 Volt with rated bus bar ,IP-42,IK-09, metal door, earth bar, neutral links complete incl blanking plates as required & fixed flush to wall / other surface complete all as specified and as directed

S&F for MCB DB SPN 8 ways Double Door 240 Volt with rated bus bar ,IP-42,IK-09, metal door, earth bar, neutral links complete incl blanking plates as required & fixed flush to wall / other surface complete all as specified and as directed.

S&F MCB 4 Pole 63 to 100 Amps , 415 Volts , 10 KA rupturing capacity , C curve complete all as specified and as directed.

S&F MCB single pole & neutral SPN 40 to 63 Amps , 240 Volts , 10 KA rupturing capacity , C curve complete all as specified and as directed.

S&F MCB single pole & neutral SPN 32 Amps , 240 Volts , 10 KA rupturing capacity , C curve complete all as specified and as directed.

S&F MCB single pole 6 to 32 Amps , 240 Volts , 10 KA rupturing capacity , C curve complete all as specified and as directed.

Supply ,laying ,jointing and testing in trenches or passing through pipe, 1100 Volts grade XLPE insulated, armoured heavy duty electric cable with aluminium conductor of cross sectional area 6 Sqmm 2 core with necessary fixing arrangements such as lugs, glands and terminal etc complete all as specified and as directed

Supply and fixing LED building light fitting 35 watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65 /66 protection and impact resistance of IK07 complete GI bracket 1.5m long made out of GI dia suitable for fixing street lights bend to suitable radius incl 2 sets of clamps nuts bolts washers incl painting with aluminium paint etc complete all as specified and as directed.

Taking out XLPE cable of any type/any size complete all as specified and as directed.

Supply and lay cable XLPE Insulated screened Meter PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm x 3.5 core complete all as specified and as directed.

Supply and laying DWC pipe SN-4 with coupler 40 mm OD, ISI marked along with all accessories like socket bend couplers etc. Conforming to IS 14930 , part II complete with fitting and cutting , jointing etc . Laid in trenches /fixed to pole /laying under road crossing /fixed on pavement wall with clamps complete all as specified and as directed.

M&L for Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5mtrs below normal ground level connected with galvanised iron/steel earth wire of 4 mm dia by means of bolts, nuts, check nuts and washers made out of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part-I and earth wire protected by galvanized pipe light grade 15mm bore and connected to DBs including necessary earthwork and excavation in any type of soil, GI light grade 20mm bore watering pipe with funnel and wire mesh, PCC (1:2:4) type B1 chamber with 40mm thick RCC (1:2:4) type B1 design mix cover slab with 6mm dia MS bars at 100mm c/c both ways with MS Hook 6mm dia MS bars etc complete all as specified and directed by Engineer-in-Charge including testing on completion.

Taking out old existing water tank 500 Ltrs capacity any type commplete all as specified and as directed.

Taking out old GI Tubing 20/25 mm with with Gun metal valve of any type commplete all as specified and as directed.

S&F rotational moulded polythylene water storage tank, 500 litres capacity, anti bacterial, UV and heat resistant 3 layer, ISI marked, multi layer construction (cylindrical vertical with closed top), hoisted & fixed in position including supply and fixing of 20mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe of having weight not less than 210 gms, with threaded cap/Lid including connection including dismantling of old unserviceable water tank complete all as specified and as directed.

M&L for 25mm dia steel tubing medium grade galvanised with all fitting fixed complete to walls and ceiling or floor complete all as specified and as directed

Supply & fix 25 mm bore Gun metal valves, ISI marked with iron wheel head screwed both ends for GI pipe complete all as specified and directed

KARMA TSETEN BHUTIA (BID ID -3468019)

M/S ANIL KUMAR THAKUR (BID ID -3468260)