SPECIAL REPAIRS TO BLDG NO. P-385 (UNIT MAGZINE), P-682, P-670, AND P-1504 (TRG ROOM/AUDITORIUM) AT MIL STN JAISALMER UNDER GE (A) JAISALMER

Amount

Taking down cement or cement lime plaster from stone walls etc including racking out joints hacking for key scrubbing down with water etc & removing rubbish out side MD land all as directed.

Dismantling floor, hearth or wall tiling including cement mortar, removeing and rubbish off the premises all as specified and directed by Engineer-in-charge.

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15 cm thick (below or above ground level) & removing rubbish out side MD land all as specified and directed by Engineer-in-charge.

M&L for glazed ceramic drak shade tiles in vertical surfaces 350x250x7mm or 450x350x7mm set and jointed in neat cement slurry and pointed in coloured cement incl boarder tiles with 15mm thick rendering as in backing coat of CM 1:6 all as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exc 0.06sqm but not exc 0.11sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement over 15mm thick screed bed in CM 1:6 all as specified.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in floors & finished the surface even & fair without using extra cement all as specified.

M&L for rendering 10 mm thick on concrete surface in cement mortar 1:6 & finished the surface even & fair without using extra cement all as specified.

M&L for rendering 15 mm thick on stone masonry surfaces or surfaces other than fair faces of brick work or on one side of lathing in cement mortar 1:6 & finished the surface even & fair without using extra cement all as specified.

M&L Preparation of plastered surfaces and applying three coats of white wash on ceiling surfaces all as directed

M&L for Preparation of old plastered surfaces and applying one coat of white wash on walls all as directed

S&F in repair flush pipe of polyethylene of low or high density of PVC 32mm dia for low level flushing cistern / WHB all as specified and directed by Engineer-in-charge.

S&F in repair vitreous china squatting pan orissa pattern complete of size 580 x 440 mm white with intagral foot rest and making good to the floor complete fixed in repairs. (Make:-Cera Cat No S3010102 , Hindware Cat part No - 20042)

S&F in repair PVC low level white flushing cistern syphonic action type 10 ltrs capacity incl flush pipe 32 mm dia incl PVC connection 450 mm long and complete fixed in repairs.(Make:-Cera Cat part No B1010102, Hindware (Sleek) , Commander(Water Bird) all as specified and directed by Engineer-in-charge.

S&Fin repair wash hand basin vitereous china flat back size 550 x 400 mm white incl CP waste coupling waste pipe brackets complete fixed in repairs all as specified and directed by Engineer-in-charge.

Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames) all as specified and directed by Engineer-in-charge.

S&F 150 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-charge.

S&F 150 mm long Aluminium handles, cast type, anodised complete.

S&F Butt hinges 100 mm including necessary welding if required all as directed by Engr- in -Charge.

S & F MS Pressed handle 150mm size oval type stove enameled black all as specified and directed by Engineer-in-charge.

S & F Butt hinges MS 100 mm cold rolled complete all as specified and as directed

S & F mild steel tower bolts 150 mm long stove enameled black with bright bolt complete all as specified and directed.

S & F mild steel sliding bolt 300 mm long plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fix complete all as specified and as directed

S & F 35 mm thick factory made second class hard wood, kiln seasoned and chemically pressure treated plain framed, panelled shutter (Two panel) with lock rail and panel of 9 mm BWP Commercial ply or 12 mm veneered particle board with commercial face veneers on both faces or 10 mm bison panel all as directed by Engineer-in-Charge

S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. all as specified and directed by Engineer-in-charge.

S & F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MSD square tube etc all as specified and as directed.

S&F factory made solid PVC moulded masonic door shutter 28 to 30 mm thick (style) with 2, 4, 6 raised panel design with 2 mm moulded PVC sheet on the front face and2 mm moulded PVC sheet on back face supply and fixing in the frame at site as per specification with particle board core complete all as specified and directed.

S&F 140 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drwn steel spring, fixed in floor complete as directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame exc 1.5 sqm including punching or drilling out old glazing pins/ springs clips and providing and fixing new ones.

S & F 4 mm thick plain glass and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane.

S & F in repairs Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples

M&L for perparation of old surface of wall and ceiling by complete removal of existing treatment .

M&L for Preparing newly putty surfaces and applying two coats of oil bound distemper over one coat of primer on walls.

S&F GI tubing (ISI) marked) medium grade with all fitting including taking down old pipe and fixed complete to wall ceiling or laid in floors of following sized :-

(a) 15 mm bore

(b) 20 mm bore

Taking down old steel tubing including cleaning and connections in new or old position (Wall, ceiling, floors etc) of the following size :-

(a) 15 mm bore

(b) 20 mm bore

S&F bib tap 15 mm dia cast copper alongwith crutch or butterfly handle screwed down CP fancy type 15 mm dia fixed in repairs.

S&F stop valve 15 mm bore CP fancy type screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union and fixed in repairs.

S & F in reapir 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors fixed to walls all as directed by Engineer-in-Charge.

M&L for PCC 50 mm thick type C1 1:3:6 (20 mm graded stone aggregate) laid in alternative as in plinth protection including finished the surface even & fair without using extra cement& filling the joints with mastic filling i.e one part of bitumen 85/25&3 parts of sand by weight.

M&L Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

M&L Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer.

M&L Preparation of old wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coats of Synthetic enamel paint all as specified and directed by Engineer-in-charge.

S&F Precast Reinforced Cement concrete Type B0 (Using 12.5 mm graded stone aggregate) in 35 mm thick Jallies or louvers including all mouldings complete and set in Cement Mortar 1:4 all as specified and directed by Engineer-in-charge.

Dismantling water tanks and removing to store (exc500 and not exc 1000 ltr cap)

S & F 1000 litres capacity Three Layers White colour Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including taking down old PVC tank

S&F of 15mm dia bore of pipe Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed

M & L for machine cut kota stone slab flooring 550x550x18 to 20mm thick laid over cement screed bed jointed & pointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing & mirror polishing including over a screed bed or bedding layer of 15mm thick in CM 1:6 for laying floor finishes all as specified.

M & L for machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with with grey cement slurry mixed with pigment to match the shade of slab including rubbing & mirror polishing including over a screed bed or bedding layer of 15mm thick in CM 1:6 for laying floor finishes all as specified.

M&L for granite slab of any type of 20mm thick machine cut bedded and jointed with grey cememt slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and plishing complete all as specified and directed.

M&L for applying two coat of destemper oil emulsion over a coat of primer over putty surface complete all as specified and as directed by Eng-in-Charge.

S & F 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe.

S&F in repair Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)(Make:-Cera Cat No S4020102 , Hindware Cat part No - 60002)

S & F Steel windows with side hung shutters including projecting type hinge with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded

-- ditto--- all as per item above but without glazing bars all as specified and directed by Engineer-in-charge.

S & F Mild steel work in framed work such as grills, gratings, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work confirming to Fe290-Gde-E-165 all as specified and directed by Engineer-in-charge.

S & F in repairs Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union all as specified and directed by Engineer-in-charge.

S & F tubular aluminium anodised 60 cm long towel rail 20mm dia D type complete fixed with screws etc.

S & F 3.0 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares n.exc 0.5 Sq. M in each pane all as specified and directed by Engineer-in-charge.

Taking down Chowkhats or frames .exc 1.50sqm but n.exc 4sqm each with shutters (without taking off shutters from the frames) including taking off the old fasts complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete as specified as directed.

S&F Steel windows or ventilators, fixed type, with glazing bars all as specified and directed by Engineer-in-charge.

S&F Mild stell work as in hold fasts complete conforming to Fe-290, Gde-E-165.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel nut & bolt to steel window / ventilater.

S&F 125mm X 60mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified.

S&F 35mm thick 2nd class hard wood factory made plain framed, panneled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stiles as per IS-1003 (Part-I0, kiln seasoned and chemically pressure treated.

S&F 1st class hard wood small fittings such as bracjets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labour, articles n.exc 200cu cm each.

300mm long aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed.

150mm size extruded aluminium alloy handles, fabricated type, anodised all as specified and directed by Engineer-in-charge.

M&L PCC 1:2:4 type B-1 using 20mm graded stone aggregates as in bed blocks for hold fasts etc.

S&F door closer hydroaulically regulated designation no3 univarsal type suitable for door shutter of 851 to 1000mm in width and weight between 61 to 80 kg.aluminium (dia cast body aluminium)

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finishing the surfaces even and smooth with out using extra cement.

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces, finishing the surfaces even and smooth with out using extra cement.

M & L for plastering 5mm in CM 1:4 on ceiling / chajja complete all as specified and directed.

M&L for threecoats of white wash on newly plastered ceilling surfaces including preparation of surfaces.

M&L for two coat of cement base paint on newly plastered surface including preparation of new plastered surface.

Demolition of cement concrete (un reinforced) in any description and in any position not otherwise specifically provilded.

Plain cement concrete 1: 2 :4 mixed type B2 using 40 mm graded stone aggregate 100 mm thick as in floor toping , finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

Material and labour for applying cold bituminous primer @ 0.30 ltr/Sqm confirming to IS-3384 and laying APP polymer modified membrane non-woven polyester reinforcement of 3mm thick, weighing not less than 3.5 Kg/Sqm with plain polythene finish and sealing all the over laps of 75mm in length side and 100mm on the width side of membrane by torching the same all as per manufactures instructions and all as specified and directed. Including removing existing unserviceable water proofing treatment and washing down with water to remove all dirt etc. also including 50 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in floors, roof padding & finished the surface even & fair without using extra cement including approved water proofing compound as per manufacturer's instructions or by 3% of weight of cement all as specified.

Supply only water proofing compound

Demolition of brick work /stone masonary built in cement mortar incl coping of any description all as specified and directed.

M&L squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 all as specified.

M&L squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 but except sotne.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified.

M & L for Keyed pointing to rubble masonry uncoursed or brought up to courses in cement mortar 1:4

Taking down all loose plaster and concrete if any in RCC columns, Chajjas, beams, slabs or any other type of RCC members, removing all loose ruts/scale from reinfocement etc by using wire brushes, sand paper or any other chemicals, applying a coat appoxy coating on old reinforcement, tying IRC fabric of size 75 x75mm of 3mm dia and binding with mild steel wire annealed with existing reinforcement and applying cement slurry uniformly to exposed surfaces with 10mm thick rendering in CM 1:4 finished even and smooth with out using extra cement and removing the debris from the site, complete all as specified and directed by Engr-in-Charge.

M&L for ceramic coloured tiles 9 to 10 mm thick area of each tile exc 0.18sqm but not exc 0.38sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement over 15mm thick screed bed in CM 1:6 all as directed (size 600mm to 600mm)

...ditto….as per item above but as in skirting, steps etc in vertical surfaces with 10mm thick rendering as in backing coat in CM 1:4

Hacking out old broken glass (any thickness, size, quality or description) from metal frame exc 1.5 sqm including punching or drilling out old glazing pins/ springs clips and providing and fixing new ones.

S & F 4 mm thick plain glass and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane complete all as specified and directed by Engr-in-Charge.

S & F Rolled Mild Steel Framed work as in doors or Gates of angle or other section confirming to Fe 410 - S, with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering and hanging and fixing complete.

S & F in repairs Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples

S&F in repair MS powder coated drapery rod 25mm dia decorative manner all as per sample and all as specified and directed by Engineer-in-charge.

S&F in repair Brackets powder coated fancy type for drapery rod all as specified and directed by Engineer-in-charge.

Preparing old painted surfaces by washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of distemper oil emulsion on surfaces of walls.

Preparing old plastered or un plastered surfaces and applying one coats of cement base paint on surfaces of walls, column, beam, chajjas etc.

S&F chequered cement concrete tiles 30cmx30cmx22 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry as in floors including over a screed bed or bedding layer of 15mm thick in CM 1:4 for laying floor finishes with 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base etc.

Taking down aluminum window / ventilator complete of any size, incl all fittings etc, complete all as directed.

S&F of powder coated aluminum sliding window comprising of sliding runner of three way (track), consisting of two sliding shutter duly fitted with 5.0 mm thick galss and one shutter duly fitted with stainless steel wire cloth of 0.36 mm nominal dia of wire & average width of aperature 1.4 mm with and incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc and down push type locking arrangement in glass shutter, incl necessary fixing arrangement i.e. rawl plug etc, complete all as directed. Make of Section : Jindal / TATA / Hindalco.

S&F anodised aluminium door shutters, aluminium section weighing 055 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handle 2 Nos in each door, hinges anodised aluminium sanp beading screw etc complete all as specified.

Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane 5.5mm thick glass.

Solar control film 25 micron reflective type sticked to glass panes as per instruction of manufacturers.

Dismantling of false ceiling of any description, any thicknes including cover fillets and frame work etc, complete all as specified and directed.

S F GI frame work for seamless ceiling made of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 M length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as directed.

M&L for providing and fixing Gypsum Board 12 mm thick in Ceiling fixed with screw as per Manufacturers instructions.

M& L for two coat of Oil bound distemper on ceiling surface complete all as specified and directed by Engr-in-Charge.

Taking down carefully old copper/Aluminium point wiring , fitting and fixtures complete such as switches,ceiling rose, pendenent, regulators, sockets etc , removing unserviceable materials from site and making good disturbed surface etc complete as per arrounding and as directed.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes all as specified.

M&L for point wiring using approved colour coding as per IS (Red , Black and Green for single phase circuits),with multistranded copper conductor 1.5 sq mm nominal cross-sectional area , single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, ISI-694 marked with valid CML No.in and inciuding medium grade, PVC conseled conduit and accessories etc, ISI marked with mild steel/pressed steel sunken box (with earth dolly) duly painted with two coats of anti corrosive paint/aiuminium paint over a coat of red oxide primer internally. and two coats of black bituminous paint over a coat of red oxide primer externally, with modular white cover plate with frame for mounting modular switches, socket and fan regulators etc, inciuding PVC insulated multistranded copper conductor 1.5 sq mm nominal cross sectional area single core FR LS cable as earth continuity conductor to common earth and connecting to earth duly completed all as specified and directed by Engr-in-charge for the following :-

(a) One light/fan point controlled by one switch 5 Amp one way

(b) -Ditto- all as per item above but socket outlet 3 pin 5 amps same board

(c) -Ditto- all as per item above but socket outlet 3 pin 5 amps Independent board

-Ditto- all as per item here-in-before but for one socket outlet of 15 Amps fixed on independent board with 4.0 Sq mm multistranded copper conductor wire FRLS PVC insulated and 4.0 Sq mm copper conductor wire FRLS PVC insulated using as earth wire complete all as specified and directed by Engineer-in-Charge

S & F in repair of modular type 1 way 6 Amp complete all as specified. Make: Legrand, Havells (Crabtree), Kolors

S & F in repair of socket ,6 A - 2/3 pin combined 2 modue complete all as specified. Make: Legrand, Havells (Crabtree), Kolors

S & F in repair of modular switch 1 Way 16 A,1 module complete all as specified. Make: Legrand, Havells (Crabtree), Kolors

S & F in repair of socket 6A/16A - 2/3 pin combined 2 module complete all as specified. Make: Legrand, Havells (Crabtree), Kolors

S & F ceiling rose 65 x50 mm three terminal 230 volt ISI Mark Complete Make: Havells, Anchor or equivalent make

S&F in repair MCB DBs sheet metal enclosure SPN 12 Way 220Volt with 200 Amps rated bus bar 12way double door type complete all as specified. Make: Havells, Legrand, ABB

Supply and fixing MCB's single pole 6 Amps to 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve, Make: Havells, Legrand, ABB

Supply and fixing MCB's SPN 40 Amps, 240 Volts,10 KA rapturing capacity 'C' curve, Make: Havells, Legrand, ABB

S & F for recess mounted 2' x 2' square LED panel 36 watts neutral white in light , 596 x 596 x 9 mm size, sleek design aluminium housing, polycarbibate diffuser white powder coated finish operating voltage 140 volts - 270 volts, AC, 50 Hz including taking down old unserviceable existing light fitting of any description complete all as directed by Engineer- in-charge. Make- ORIENT, Philips, Wipro.

Fixing Only Air Circulator fans AC Supply, heavy duty metal body suitablefor fixing on wall by means of necessary fixing arrangements, 230 volts single phase oscillating 750 mm sweep 3 blades having revolving speed 1440 Rev per min suitable for wall mounting complete all as specified and directed Make; Almonard, Havells and Bajaj Supreme.

S&F freedom type LED street light fitting 30 Watts, with IP 66 Protection eficacy should be more or equal to 100 Percent pressure die cast aluminium housing,heat resistant glass,IP 65 protection better optics for unifrom distribution single core copper flexible cable of size 1.50 Sq mm complete all as specified. Make- ORIENT, Philips, Wipro

Fixing Only exhaust fans AC Supply , single phase 230/ 240 V Heavy duty in metal body of size 600 mm sweep with complete fixing arrangenment from motor to Ceiling with louver Complete all as specifed. Note : Exhaust Fan 600 mm sweep will be given under Schedule B free for fixing.

S & F in repair bracket of GI pipe medium grade of 40 mm dia, 1.2 meter in Length clamps made of FI 40 mm x 6 mm Incl nuts,bolts & washers ,painting complete as specified.

M & L bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground levl connected to galvanized iron strip 32 x 6mm as earthing lead up to 7.5 mtr by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 40mm dia light grade pipe for earth lead protection and testing on completion complete all as specified and directed.

Taking down the existing unservicable sub main wiring of any type / description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

All as per Item No. 4 above but with stranded copper conductor 4.0 Sq. mm (nominal area), single core, PVC insulated and unsheathed multistranded FRLS cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated multistranded FRLS copper conductor 4.0 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

S&F for Switch piano flush type single pole one way, and 6 amp complete ISI mark complete all as specified.

S&F for Socket outlet multipurpose having provision for 2 in 1, 3 pin 5 amp piano flush type complete all as specified

S & F for Switch piano flush type single pole one way, and 15 amp complete ISI marked complete all as specified.

S&F for socket outlet 2 in 1, 2/3 pin 5 Amps and 15 Amps flush type complete all as specified.

S & F for MCB DB SPN 4 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 230 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed .

S & F for LED tube light fitting 20 Watt 4 Feet or 1183 MM in lenth, IP 20 Protection, wall mounted type, Slim LED Batten with polycarbonate housingand diffuser, elegant design with end caps, having excellent thermally managed polycarbonate extrution, LM 80 Certified LED having Integral Electronic Constant Current Driver , IP 20 Protection, Opreating voltage 240 V , 50Hz AC Supply and Operating tempraeture 0 to 50 C, Power factor ≥ 0.9, Lumen output ≥ 2000, necessary mounting arrangements on PVC Square box 2 Nos, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified Make Orient, Philips, Crompton, Havells etc

S & F for LED tube light fitting 10 Watt, 2 Feet or 591 MM in length, IP 20 Protection, wall mounted type, Slim LED Batten with polycarbonate housingand diffuser, elegant design with end caps, having excellent thermally managed polycarbonate extrution, LM 80 Certified LED having Integral Electronic Constant Current Driver, IP 20 Protection, Opreating voltage 240 V , 50Hz AC Supply and Operating tempraeture 0 to 50 C, Power factor ≥ 0.9, Lumen output ≥ 1000, necessary mounting arrangements on PVC Square box 2 Nos, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified Make Orient, Philips, Crompton, Havells etc

S & F Energy saving new generation 10/12 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Make Orient, Philips, Crompton, Havells etc

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as directed by Engineer-in-Charge. Make Orient, Philips, Crompton, Havells etc

S & F in repair bracket of GI pipe medium grade of 40 mm dia,clamps made of FI 40 mm x 6 mm Incl nuts,bolts & washers,painting complete as specified.

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 4.00 Sqmm (FRLS) in cassing & Capping including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 4.00 Sqmm (FRLS) of continous earth wire green in colour complete with two coat of black bituminus painting of old steel conduit with enamel paint of superior quality after scratching of old paint with sand paper complete all as specified and directed by Engr-In-Charge.(Note :- Two runsof 4.00 Sqmm cable & one run of 4.00 Sqmm cable and one run of cassing capping shall be paid as one unit length)

M & L for making hole in wall suitable for fixing exhaust fan of 380 mm sweep by cutting the wall and make suitable plaster and cover the damages done to wall and making good disturbed surface complete all as specified

Supply & fix exhaust fans iron body heavy duty AC single phase 230/ 240 V of size 380 mm sweep with louver complete all as specified and as directed.

Taking down ceiling fan / Exhaust fan of any sweep sealing cable end dismanting blade and removing fan and blade to store complete all as specified and as directed.

M & L for Painting of ceiling fan/ Exhaust fan complete in situ with synthetic enamel paint by spraying including filling cavity with filler one coat after cleaning all dust etc complete all as specified and as directed.

Fixing only exhaust fan and connecting up including provn of cable from ceiling rose or connector to fan complete all as specified and as directed.

S & F in repair switch Piano type 1 way 5 Amp complete all as specified.

S & F for MCB DB SPN 8 way with provision as out going double door IP 43 complete prewired including Bus Bar etc suitable for operation on 230 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed .

S & F in repair of LED tube light fitting 1 x 20 Watt LED 6000K (1144 mm) wall mounted LED batten,extruded aluminium heat shink provided for efficient heat dissipation & integrated electronic driver,optic diffused type E LITE LED TRIYCA including all electric connection with whilte flexible cord 1.50 Sqmm 3 core as required complete all as specified and directed.Make :- Bajaj/Philips/Havells /Crompton /Syska/Wipro

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 30 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade required dia 1.5 mtr long bend to required shape complete all as directed by Engineer-in-Charge. Make- Make :- Bajaj/Philips/Havells /Crompton /Syska/Wipro

M & L bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground levl connected to galvanized iron strip 32 x 6mm as earthing lead by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 40mm dia light grade pipe for earth lead protection and testing on completion complete all as specified and directed.

Fixing only desert cooler electric driven (single phase), having nominal air flow capacity of 4000 CuM per hour (or nearest size).Plastic/PVC Body complete all as specified and directed by Engineer-in-charge

M & L for Cooler stand made out of angle iron of suitable size suitable for desert cooler complete fixing with angle fastner complete all as specified and directed by Engineer-in-charge

M/S SHRI HARI CONSTRUCTION COMPANY

Leelashah Enterprises