Miscellaneous civil works for enclosure of EBW at SCRF Hall and HEL lab platform of C block at RRCAT Indore

Amount

Imp. Note (applicable to the entire work) 1. The bidder must possess valid EPF & ESIC registration. 2. The bidders need to deposit EPF & ESIC with appropriate authority. The reimbursement for EPF & ESIC deposit shall not be made. 3. The payment of wages to labourers should be made through bank 4. The bidder must possess sufficient manpower & other resources (as detailed in SGF ) required for the timely completion of work. 5. Bidders are encouraged to visit site to understand the intricacies of the work before quoting.

Providing, fabricating, installing and fixing in position exterior grade 4 mm thick aluminum composite panels of required size over aluminum frame work for masking, fascia, cladding, etc. for linear as well as curvilinear shape for all heights and all levels etc. as per design requirement. The frame members shall be cladded by using 4.0 mm thick prime quality aluminum composite panels approved shades made out of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thick)

Using tape and sealent for fixing aluminum panels/glass, necessary filling up of gaps at junctions, top, bottom and all sides by glass sealent, all fittings and fixtures necessary for fixing of panels, screws / rivets, G.I. wire etc., making cut outs, fixing extra frame work and necessary arrangements for opening for supply/return air slit, lighting fixtures, including scaffolding etc. complete as per drawings, specifications and as directed by E.I.C.

Providing and fixing in position Aluminum framing, members etc. with extruded and anodized (5 microns) to natural aluminum colour, aluminum sections, beadings, sheets etc. as required manufactured to relevant IS codes using heavy sections etc. including cost of fixures, fitting, screwsetc. as required complete as per drawing, specifications and as directed by Engineer-in-Charge.

1. Payment will be made on the basis of weight of Aluminum members/sections fabricated and actually installed in position without extra allowance for wastage. No extra payment will be made for all non-aluminum consumable items like screws etc.

2. The Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angles at no extra cost.

Providing and fixing in position anodized (min of grade AC5) aluminum doors with extruded and integrated aluminum sections as per approved make confirming to IS: 733 and IS: 1285 aluminum beading, PVC lining, CP brass / stainless steel screws, mastic filling, nuts, washers etc. complete including scaffolding if necessary, chipping of walls, beams, columns, rectification of plaster, painting if required. Vertical and middle horizontal section of door shall be min 80 mm x 44 mm and of thickness minimum 2 mm. Top and bottom horizontal section of door shall be min 120 mm x 44 mm and of thickness minimum 2 mm Snap beading shall be minimum 0.41 mm thick. Cleat angles shall be minimum 25 x 25 mm and thickness 2 mm.

Including providing and fixing in position 5mm thick glass or opaque using 12mm thick laminated particle board. Specifications of glass:- clear sheet glass/float glass and of 5mm thickness fixed to aluminum partitions with edges champhered (wherever required) with Neoprene Gasket Lining etc. complete. Specifications of laminated board:- 12 mm thick both side laminated particle board of approved exterior grade - 1, Type II confirming to IS 12823 bonded with Phenol Formaldehyde Resin in doors using necessary approved standard aluminum beadings including wastages, if any, fixing to existing framework with C.P. brass / stainless steel screws as required and other incidental charges etc. complete.

Anodized aluminum (min of grade AC-5) doors, fully glazed with 5 mm thick glass or opaque using 12mm thick laminated particle board and the vertical members are internally braced with 12mm dia MS long bolt, SS handle on both sides as approved, floor spring/door closer, concealed tower bolts, locking arrangements using SS aldrop 16mm dia and 300mm long etc complete.

Providing and fixing in position anodized (min of grade AC5) aluminum wall span etc. with extruded and integrated aluminum sections confirming to IS: 733 and IS: 1285 aluminum beading, PVC lining, CP brass / stainless steel screws, mastic filling, nuts, washers etc. complete including scaffolding if necessary, chipping of walls, beams, columns, rectification of plaster, painting if required. Vertical and horizontal section of wall spans shall be min 63 mm x 38 mm and of thickness minimum 1.85 mm. Snap beading shall be minimum 0.41 mm thick. Cleat angles shall be minimum 25 x 25 mm and thickness 2 mm. The spacing of verticle and horizontal sections shall be in the range of 0.90 m to 1.50 m centre to centre.

Including providing and fixing in position 5mm thick glass or opaque using 12mm thick laminated particle board. Specifications of glass:- clear sheet glass/float glass and of 5 mm thickness fixed to aluminum doors with edges champhered (wherever required) with Neoprene Gasket Lining etc. complete. Specifications of laminated board:- 12 mm thick both side laminated particle board of approved exterior grade - 1, Type II confirming to IS 12823 bonded with Phenol Formaldehyde Resin in partitions using necessary approved standard aluminum beadings including wastages, if any, fixing to existing framework with C.P. brass / stainless steel screws as required and other incidental charges etc. complete.

Wall spans fully glazed with 5mm thick glass or opaque using 12mm thick laminated particle board, anodised aluminum (anodised transparent or dyed to required shade as directed by EIC as per IS: 1868, minimum anodic coating of grade AC 5).

Providing and fixing in position anodized (min of grade AC5) aluminum sliding door glazed with glass or opaque using laminated board etc., using aluminum alloys extruded section as per approved make confirming to IS: 733 and IS: 1285. Vertical and middle horizontal section of door shall be min 80 mm x 44 mm and of thickness minimum 2 mm. Top and bottom horizontal section of door shall be min 120 mm x 44 mm and of thickness minimum 2 mm Snap beading shall be minimum 0.90 mm thick.

Cleat angles shall be minimum 25 mm x 25 mm and thickness 2 mm, Horizontal section of door for hanhing roller shall be min 63 mm x 38 mm and of thickness minimum 1.85 mm, Channel section for roller shall be minimum 38 mm x 38 mm and thickness of 1.75 mm, Snap beading shall be minimum 0.41 mm thick., including providing and fixing locking arrangement for lock, heavy duty roller, C.P. brass screws / stainless steel screws, nuts, washers, Rawl plugs, aluminum packing strips used for anchoring system as per the requirements, transportation, cost of all labours, scaffolding if necessary, machinery, tests, chipping of walls, beams, columns, rectification of plaster, painting if required etc. and as directed by EIC. Including scaffolding if necessary. Including provision for fixing float glass panes of 5.0 mm thickness or 12 mm thick particle board as directed by EIC.

Including providing and fixing in position 5mm thick glass or opaque using 12mm thick laminated particle board. Specifications of glass:- clear sheet glass/float glass and of 5 mm thickness fixed to aluminum doors with edges champhered (wherever required) with Neoprene Gasket Lining etc. complete. Specifications of laminated board:- 12 mm thick both side laminated particle board of approved exterior grade - 1, Type II confirming to IS 12823 bonded with Phenol Formaldehyde Resin in partitions using necessary approved standard aluminum beadings including wastages, if any, fixing to existing framework with C.P. brass / stainless steel screws as required and other incidental charges etc. complete.

With anodized aluminum section (min of grade AC5) of approved shade

Providing, fabricating and erecting S.S. tube railing of 304 Grade comprising 50mm dia. & 16 gauge thick S.S. single pipe for top and 25mm dia. double member for vertical. Providing and fixing runner pipes of 19mm dia. S.S on middle in three rows. including providing and fixing bottom and end caps as per approved design on the top & end of the members, buffing of welded surfaces, cost of all fittings & hardware, clamps screws etc. cutting, welding the joints, grinding/muffing if necessary etc. complete.

Soni construction company