GMCH/200 ICU/ Gr-B Construction of 200 bedded Covid ICU at 2 storied Parking at GMCH, Bhangagarh, Guwahati (Including electrical works), Gr-B

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Excavating, Supplying and filling of local earth(inculding Royality) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Vertical surface such as walls (any thickness), parapet walls, partitions and the like including attached pilasters, butresses, plinth and string courses and the like.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement : 3 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured).

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing chromium plated brass handles with necessary screws etc. complete: 125 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing factory made uPVC white colour fixed glazed windows/ entilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , UPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete.

Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete

Float glass panes of nominal thickness 5 mm (weight not less than 12.00 kg/sqm)

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing bolts including nuts and washers complete.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Medium shade pigment using 50% white cement, 50% ordinary cement

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 25 mm thick

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Size of Tile 600 x 1200 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm

Providing and laying Polished Granite stone flooring and tread of steps in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (hessian based self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per square metre, including preparation of surface but excluding grading complete with Bitumen felt (hessian base) type 3 grade I conforming to IS : 1322

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing R.B. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineerin

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing, Fitting and fixing of Sherra/ Century make 12 mm thick external grade cement fibre boards with screws on MS frame work on one side including the joints to be finished with jointing tape and wall putty.(cost of MS structure to be measured and paid seperately)

Supplying, Fixing and Fitting of not less than 72 mm thick partition wall with 11 mm thk white coloured surface finished High Density Fire and water retardent WPC boards fixed over a frame of 25 x 50 x 2 Aluminium sections comprising of vertical and horizontal members fixed at a distance of not more than 600mm C/C in both directions. The 11 mm thick WPC board to be fixed on both side of the frame with 25mm drywall screw at 300 mm c/c. to be complete in all levels as per design and as directed by the department.

Supplying, Fixing and Fitting of not less than 61 mm thick partition wall with 11 mm thk white coloured surface finished High Density Fire and water retardent WPC boards fixed over a frame of 25 x 50 x 2 Aluminium sections comprising of vertical and horizontal members fixed at a distance of not more than 600mm C/C in both directions. The 11 mm thick WPC board to be fixed on the one side of the frame with 25mm drywall screw at 300 mm c/c. The frame shall have additional aluminium section to support the Bed Head Panel including cross bracings between two partions so as to support each other to be complete in all levels as per design and as directed by the department.

Providing ditting and fixing of 30 mm thk BWP grade green/century/ or equivalent)solid core flush door with 6mm glass panels fixed on rebate on the face and timber beads on back. The edges of the flush door shall be finished with 6mm thk teak wood liping. The timber beads and teak wood lipping shall be polished as per the approved shade of colour and the door to be finished with 1 mm thk laminate of Greenlam/Century/Merino make on both sides as well as the rebate including nessecary harware fittings like 100 mm SS hinges and screws, complete at all levels as per design and as directed.(lock, door closer/floor spring, tower bolt) to be measured seperately.

Providing, supplying and fixing of Frameless Single leaf/double Swing Glass Door of Dorma/ Ozone or equivalent make in glazing using 12mm thick toughened glass of Saint Gobain / or approved equivalent with die cast patch fitting with stainless steel cover including fixing of patch fittings, floor springs, locks, handles etc. using the hardware items as detailed, complete in all respects as per detailed drawings, specifications and direction of Engineer in charge. Single Leaf Door with Dorma or Equivalent Hardware’s as specified:- Swing Glass Door which includes each of Top Pivot PT 24, Bottom Patch PT 10, Top Patch PT 20, Floor Lock US 10, Strike Plate , Floor Spring BTS 75v, with pair of TGDIH SS Pull Handle 25 mm dia x 450 mm long and other accessories for self closing feature as per detailed drawings.

Glass door with 12 mm thick clear toughened glass including all accessories with Dorma make Sensor mechanism equipment with Magnet system overpanel complete as per design and as directed at all levels.

Providing and fixing 2.4m high FRAMELESS GLASS INTERNAL PARTITIONS at all locations with 12mm clear tempered glass or as per elevation drawings enclosed with approved make of 316 grade patch connector S.S. fittings of DORMA/Ozone or equivalent make , fixed with S.S. screws or with fixing clips including necessary filling up gaps at junction, at top, bottom u channel make jindal and sides with required weather silicon with backer rod shall be inserted between alluminium section channel and glass as well as both inside and outside around the periphery of the glass to make the glazing water tight and air tight as shown in enclosed drawings and directions of Engineer-in-charge. Glasswork including making suitable holes in the glass before tempering process of glass, for installation complete as per design drawings. The periphery shall have to be sealed both from inside and outside with silicon weather sealant to make the glazing water and air tight.The sealing of glass to patch connector hardwares with stainless steel fixtures as detailed in drawings. Silicon sealant grade shall be "Dow corning - USA" or " "WACKER - Germany" or approved equivalent as per the design requirement. The partition shall be aligned for the entire height and for the entire length by laser beam equipment to ensure 100 percent X-axis and Y-axis alignment. The glass joints must be properly sealed with weather silicon to make the joint water tight and air tight as well. as per directions of Engineer-In-Charge.

Glass door with 18 mm thick clear toughened glass including all accessories with Dorma make Sensor mechanism equipment with Magnet system overpanel complete as per design and as directed at all levels.

Supply and installation of Merino /Greenlam (Nylon) series cubicles of width and depth as per specifications/ site drawings. Cubicle height will be 2003 mm. Made from solid grade compact high pressure laminate as per IS:2046 and EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C with bunch of kraft papers impregnated with thermosetting phenolic resin and decorative papers made of Alpha cellulose fiber impregnated with thermosetting melamine resin which provide superior scratch, abrasion, heat, chemical, impact, graffiti & moisture resistance along with anti-bacterial properties. Panels have a black core that when machined, presents a distinctive black edge. All doors will be of single colour and made of 12 mm thick HPL compact panel. The doors will have chamfered edges. Each door will be supported by 3 no.s Nylon PA-6 made hinges affixed to the pilasters. Nylon PA-6 made coat hook and lock set are provided with each door. All pilasters will be made of 12 mm thick HPL compact panel with chamfered edge and completed with stainless steel made thumb turn lock set. Aluminum made door stopper profiles with rubber linings for dampening the noise while door closing will be provided at the vertical ends of the pilasters. Pilasters will be anchored to the floor using Nylon PA-6 made adjustable legs .The bottom gap is 100-150 mm. All intermediate partitions or dividers will be made of 12 mm thick HPL compact laminate panels. They are affixed with aluminium made U-channel at their ends for ultimate stability of the system. Design no. as specified by Arch. / Engr. in suede finish. Size of panels to be as per drawing.

Supply, Fitting and Installation of 2mm Thick Homogenous Vinyl flooring of Diamond 10 Technology with PUR range including all accessories like welding rod strip etc installation complete as per approved shade complete in all levels. The product should to conform to Group "T" wear resistance as per EN649 clean room certified with Class "A" as per ASTMF 5100. The product should have flamabality resistance of Class BF1-S1, Slip resistance of Class R9 as per DIN 51130. The product should exhibit Anti Static behavior, resistance to Bacteria, resistance to Staining, sustainibility to Castor chair.

Providing, fitting and fixing of 75 mm manually operated Black out Roller blinds with necessary hardware complete as per choice and as directed.

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) M/F Suspended Ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I. intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mmx10mmx0.55mm thick fixed to soffit with G.I.cleat and steel expansion fasteners. Ceiling sections of 0.55 mm thk with knurled web of 51.5 mm and two equal flanges of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips perpendicular to the intermediate channel at 457mm c/c and 6 mm thk Calcium Silicate HILUX Board fixed to the ceiling sections with 25 mm drywall screws at 230mm c/c. the boards joints are finished with joint paper and two coats of drywall topcoat at all levels including cutting for providing and fixing light fixures whwre ever necessary. and as per design.

Providing and fixing factory-made uPVC white color double leaf style casement door with .) uPVC made multi-chambered frame of size 62mm*60mm uPVC made multi-chambered Sash of size 108mm *64.5mm UPVC dummy/false mullion of size 80mm * 70mm. The beading with appropriate dimension for sash is used with TPX weldable multi gasket in frames, sash etc. The outer wall thickness of profiles is from 2.5mm -2.8mm. 1.5mm & 2mm of thickness box shaped section reinforcement of 23mm * 27mm have used in all frames, sash, mullions & etc. Hardware’s used are 3D hinges 4pcs in each sash with appropriate Espag (SS 304) grade with Key locking double handle both from inside and outside in multi-point locking system in door. The installation is done with fasteners 100 * 8mm in size for fixing the frame with all SS screws wherever required during installation.Dummy/False mullion profile used between door sash.Waterproof cum Weatherproof silicone of Sika brand is used on both inside and outside of frame to fill the gap.Necessary glass packers, frame packers, wedges, casement keep, drainage caps are used for maximum protection. Complete with Saint Gobain 6mm Clear Glass in all levels as directed.

Providing and fixing factory-made uPVC white color double leaf style casement door with fix portion on left, right, upside. uPVC made panels of thickness 20mm and height 150mm of each uPVC made multi-chambered frame of size 62mm*60mm uPVC made multi-chambered Sash of size 79mm *60mm uPVC mullionused of 80mm*60mmboth horizontally&vertically. The beading with appropriate dimension for sash is used with TPX weldable multi gasket in frames, sash etc. The outer wall thickness of profiles is from 2.5mm -2.8mm. 1.5mm & 2mm of thickness box shaped section reinforcement of 23mm * 27mm have used in all frames, sash, mullions & etc. Hardware’s used are 3D hinges 4pcs in each sash with appropriate Espag (SS 304) grade with Key locking double handle both from inside and outside in multi-point locking system in door. The installation is done with fasteners 100 * 8mm in size for fixing the frame with all SS screws wherever required during installation.Dummy/False mullion profile used between door sash. Waterproof cum Weatherproof silicone of Sika brand is used on both inside and outside of frame to fill the gap.Necessary glass packers, frame packers, wedges, casement keep, drainage caps are used for maximum protection. Complete with Saint Gobain 6mm Clear Glass in all levels as directed.

Providing and fixing factory-made uPVC white color single leaf style casement window (4 pcs in each design) with fix portion on left, right, upside & bottom. .) uPVC made panels of thickness 20mm and height 150mm of each. UPVC made multi-chambered frame of size 62mm*60mm UPVC made multi-chambered Sash of size 79mm *60mm UPVC mullionused of 80mm*60mmboth horizontally&vertically Additional uPVC post of size 77mm* 77mm. The beading with appropriate dimension for sash is used with TPX weldable multi gasket in frames, sash etc. The outer wall thickness of profiles is from 2.5mm -2.8mm. 1.5mm & 2mm of thickness box shaped section reinforcement of 23mm * 27mm in all frames, sash, mullions & additional post etc. Hardware’s used are Friction stay (SS 304) with appropriate Espag (SS 304) grade and Single de-attachable handle in multi-point locking system in window. The installation is done with fasteners 100 * 8mm in size for fixing the frame with all SS screws wherever required during installation. Waterproof cum Weatherproof silicone of Sika brand is used on both inside and outside of frame to fill the gap.Necessary glass packers, frame packers, wedges, casement keep, drainage caps are used for maximum protection. Complete with Saint Gobain 6mm Clear Glass in all levels as directed.

Providing and fixing factory-made uPVC white color 3 Track with mosquito mesh sash. uPVC made multi-chambered 3Track frame of size 108mm*44mm UPVC made multi-chambered Sash of size 68mm *38mm The beading with appropriate dimension for sash is used with TPX weldable multi gasket in frames, sash etc. The outer wall thickness of profiles is from 2.5mm -2.8mm. 1.2mm &1.5mm of thickness box shaped section and sash shaped section reinforcement have been used in all frames, sash, mullions & etc. Single point locking with Touch Lock and C-shaped mosquito mesh handle have been used. - The installation is done with fasteners 100 * 8mm in size for fixing the frame with all SS screws wherever required during installation.Waterproof cum Weatherproof silicone of Sika brand is used on both inside and outside of frame to fill the gap.Necessary glass packers, frame packers, wedges, casement keep, drainage caps are used for maximum protection. Complete with Saint Gobain 6mm Clear Glass with Fibre mesh in mosquito mesh sashin all levels as directed.

Providing and fixing factory-made uPVC white color Fix frame with Georgian bar used in making design applied both horizontally & vertically. uPVC made panels of thickness 20mm and height 150mm of each. uPVC made multi-chambered frame of size 62mm*60mm UPVC made multi-chambered Sash of size 79mm *60mm . The beading with appropriate dimension for sash is used with TPX weldable multi gasket in frames, sash etc. The outer wall thickness of profiles is from 2.5mm -2.8mm. 1.5mm of thickness box shaped section reinforcement of 23mm * 27mm have used in all frame. 3M double tape have been used for fixing Georgian bars. The installation is done with fasteners 100 * 8mm in size for fixing the frame with all SS screws wherever required during installation. Waterproof cum Weatherproof silicone of Sika brand is used on both inside and outside of frame to fill the gap.Necessary glass packers, frame packers, wedges, casement keep, drainage caps are used for maximum protection. Complete with Saint Gobain 6mm Clear Glass in all levels as directed.

Providing and fixing factory-made uPVC white color 3 Track 6 panel/sash with mosquito mesh sash. uPVC made multi-chambered 3Track frame of size 108mm*44mm UPVC made multi-chambered Sash of size 68mm *38mm UPVC made frontal closing for centre locking. The beading with appropriate dimension for sash is used with TPX weldable multi gasket in frames, sash etc. The outer wall thickness of profiles is from 2.5mm -2.8mm. .) 1.2mm &1.5mm of thickness box shaped section and sash shaped section reinforcement have been used in all frames, sash, mullions & etc. AppropriateEspag (SS 304) grade with Pop-up handleand C-shaped mesh handle in mesh sash in multi-point locking system. The installation is done with fasteners 100 * 8mm in size for fixing the frame with all SS screws wherever required during installation.Waterproof cum Weatherproof silicone of Sika brand is used on both inside and outside of frame to fill the gap.Necessary glass packers, frame packers, wedges, casement keep, drainage caps are used for maximum protection. Complete with Saint Gobain 6mm Clear Glass with Fibre mesh in mosquito mesh sashin all levels as directed.

Providing and fixing factory-made uPVC white color 3 Track 6 panel/sash with mosquito mesh sash with Georgian bar used in making design applied both horizontally & vertically. uPVC made multi-chambered 3Track frame of size 108mm*44mm UPVC made multi-chambered Sash of size 68mm *38mm UPVC made frontal closing for centre locking. The beading with appropriate dimension for sash is used with TPX weldable multi gasket in frames, sash etc. The outer wall thickness of profiles is from 2.5mm -2.8mm. 1.2mm &1.5mm of thickness box shaped section and sash shaped section reinforcement have been used in all frames, sash, mullions & etc. AppropriateEspag (SS 304) grade with Pop-up handleand C-shaped mesh handle in mesh sash in multi-point locking system. 3M double tape has been used for fixing Georgian bars. The installation is done with fasteners 100 * 8mm in size for fixing the frame with all SS screws wherever required during installation.Waterproof cum Weatherproof silicone of Sika brand is used on both inside and outside of frame to fill the gap.Necessary glass packers, frame packers, wedges, casement keep, drainage caps are used for maximum protection. Complete with Saint Gobain 6mm Clear Glass with Fibre mesh in mosquito mesh sashin all levels as directed.

Providing and fixing factory-made uPVC white color single leaf style casement window (6 pcs design) with double leaf casement door using Georgian Bar in making design and applied both horizontally & vertically. .) UPVC made panels of thickness 20mm and height 150mm of each. UPVC made multi-chambered frame of size 62mm*60mm uPVC made multi-chambered window sash of size 79mm *60mm UPVC made multi-chambered door sash of size 105mm *64.5mm UPVC mullionused of 80mm*60mmboth horizontally&vertically UPVC dummy/false mullion of size 80mm * 70mm. The beading with appropriate dimension for sash is used with TPX weldable multi gasket in frames, sash etc. The outer wall thickness of profiles is from 2.5mm -2.8mm. .) 1.5mm & 2mm of thickness box shaped section reinforcement of 23mm * 27mm have used in all frames, sash, mullions & additional post etc. Hardware’s used areHardware’s used are 3D hinges 4pcs in each sash and Friction stay (SS 304) with appropriate Espag (SS 304) grade and Single de-attachable handle in multi-point locking system in window. 3M double tape has been used for fixing Georgian bars. - The installation is done with fasteners 100 * 8mm in size for fixing the frame with all SS screws wherever required during installation.Dummy/False mullion profile used between door sash. Waterproof cum Weatherproof silicone of Sika brand is used on both inside and outside of frame to fill the gap.Necessary glass packers, frame packers, wedges, casement keep, drainage caps are used for maximum protection. Complete with Saint Gobain 6mm Clear Glass in all levels as directed.

DRDO technology Bio-Degradable Bio-digester FRP tank of 5 cubic meter (2000 liters) caacity for 20users per day including Anaerobic Microbium Inoculum (AMI) 600 liters in barrels. Dimensions of tank (L) 2400x(B)1800mmx(D)1200mm

Supply and installation of SS square tank of 300 litre capacity for NAOCL storage as per design and as directed at all levels.

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow including operated levers

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External Work 32 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore.

50 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions 45cm length 20 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X4 sq. mm + 1 X 4 sq. mm earth wire

4 X 10 sq. mm + 2 X6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

2 way 5/6 amps switch

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mm X 150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 1 or 2 Module

3 Module

4 Module

6 Module

8 Module

12 Module

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 510 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

TV antenna socket outlet

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2 + 12 way, Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 12 way (4 + 36), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole and neutral

Double pole

Triple pole and neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying, installing, testing and commissioning of following capacity TPN tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with TPN disconnector FSU and HRC fuses, connections, earthing etc. as required. 63 amps TPN

100 amps TPN

200 amps TPN

315 amps TPN

Supplying, installation, including suspension, testing and commissioning of following capacity bus trunking with aluminium bus bars having current density of 130 A/ sq cm at nominal current rating in 1.6mm thick IP 42 sheet steel enclosure in convenient sections for use on, 3 phase, 4 wire, 415 V, 50 Hz, A.C. supply including jointing of sections, flexible joints, expansion joints, bends and earthing with 2 runs of galvanised iron strips, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. '800 amps

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 120 sq. mm and upto 400 sq. mm

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 300 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 25 sq. mm (28mm)

3½ X 35 sq. mm (32mm)

3½ X 70 sq. mm (38mm)

3½ X 95 sq. mm (45mm)

3½ X 150 sq. mm (50mm)

3½ X 300 sq. mm (70mm)

4 X 10 sq. mm (25mm)

4 X 16 sq. mm (28mm)

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 300 sq. mm

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

Supply of Medium class GI pipe for running of UG cable of 80mm dia.(Jindal make)

Supply of Medium class GI pipe for running of UG cable of 100mm dia.(Jindal make)

Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Supplying, laying/ fixing, testing and commissioning of following thickness resin bonded fiber glass pipe section insulation having density 80 kg/cum or mineral wool (non combustible) having density of 144 Kg/ cu m duly covered with a layer of 120 gm/sqm polythene sheet (vapour barrier) on existing pipe and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing feltstrip (as per IS:1322 as amended up to date ) at joints etc. as per specifications and as required. 75mm

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince)or other ISI approved including joining ,fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. 75 mm nominal outer dia Pipes

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince)or other ISI approved including joining ,fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. 110 mm nominal outer dia Pipes

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. 160 mm nominal outer dia Pipes

Supplying, fitting and fixing Chrome Plated (C.P.) rain water shower 200X200 mm dia of approved brand as directed and specified. (Pipes will be measured and paid separately)

Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified.

Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified.

Providing, fitting and fixing CP towel rail complete as directed and specified.

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified.

Providing, fitting and fixing robe hook complete as directed and specified.

Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified.

Providing, fitting and fixing Chrome Plated health faucet complete as directed and specified.

Supplying fiting and fixing glass division plate including fitting and fixing compete as directed and specified.

Supplying and installing 1,000 LPH RO Plant for Dialysis

Supplying and installing Water purifier (RO+UV+UF+TDS Controller) Computer controlled operation with filter change alarm and UV Fail Alarm. High purification capacity of 20 litres/hr & 9 litres detachable storage tank for easy cleaning.

Providing and fixing under counter wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Under Counter Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing brass two way bib cock of approved qualiity

Providing and fixing CP grating of approved quality and colour

Providing and fixing brass CP Pillar cock of approved qualiity

Supply of surface/pendant mounted totally enclosed linear luminaire(Ingress protection IP-65),WI0831208G1(Wipro or equivalent make 1x20W LED Tube T8.

Supply of energy efficient Ceiling fan 1200 mm sweep (Make- USHA : Model Name :Energia 32 5 star in the existing arrangement.

Supply of heavy duty 600mm sweep, 900rpm exhaust fan in the existing hole of the buildintg, turbo force SP(Considering 10% discount and 18%GST

Supply of recessed mounting glare less LED down light of size 2'x2'(>120Lumen/watt) Crompton or equivalent make.(LCTLRP-24 FO-CDL).

Supply of sky cove LED strip light including Driver in pack(24W output) available in 3000K and 6500K Philips or equivalent make.(LED strip sky cove 5M WW with driver).

Supply of recessed mounting glare less LED spot light with 30000 burning hours with CRI>8015watt 3000K and 4000K CCT Beam angle 36Deg. And Vertical Tilt 30Deg) Crompton or equivalent make.(CDR212-12-40-SL-NWH).

Supply of LED flood light made of pressure die cast Aluminium Housing with toughened glass and high power LEDs and secondary lences with IP66 .System efficiency>=110LPW. Option for 3000K 10KV SPD included. Crompton or equivalent make.(LFLN-120-CDL/60-M

Supply, installation,testing and commissioning of 630A Electrical panel made of sheet steel(1.6mm thick, CRCA) alingwith 1000A Al Bus- bar(Vertical and Horizontal of size 100x10) paint with RAL7072(70 micron) as per IEC 60439, indoor type IP-42(1800HX1400WX550D) and backside cable alley, bottom incoming and top outgoing. and as specified by the Department

Supply,installation, testing and commissining of 315A Electrical panel made of sheet steel(1.6mm thick, CRCA) alingwith 600A Al Bus- bar(Vertical and Horizontal of size 60x10) paint with RAL7072(70 micron) as per IEC 60439, indoor type IP-42(1875HX1200WX550D) and backside cable alley, bottom incoming and top outgoing. and as specified by the Department

Supply, installation, testing and commissioning of 250A Electrical panel meant for UPS Power made of sheet steel(1.6mm thick, CRCA) alingwith 500A Al Bus- bar(Vertical and Horizontal of size 50x10) paint with RAL7072(70 micron) as per IEC 60439, indoor type IP-42(1200HX1050WX450D) and backside cable alley, bottom incoming and top outgoing. and as specified by the Department.

Supply, installation, testing and commissioning of 250A Electrical panel meant for Raw Power made of sheet steel(1.6mm thick, CRCA) alingwith 500A Al Bus- bar(Vertical and Horizontal of size 50x10) paint with RAL7072(70 micron) as per IEC 60439, indoor type IP-42(1000HX1050WX450D) and backside cable alley, bottom incoming and top outgoing. and as specified by the Department.

Supply, installation, testing and commissioning of 1250A Electrical panel meant for AMF bypass panel made of sheet steel(2.0mm thick, CRCA) alingwith 1600A CU. Bus- bar(Vertical and Horizontal of size 100x10) paint with RAL7072(70 micron) as per IEC 60439, indoor type IP-43(2175HX2650WX850D) and backside cable alley, bottom incoming and top outgoing. and as specified br the Department.

Supply, installation, testing and commissining of Hospital utility items(1.5Tr Split A/C=4 Nos,1.8Tr. Split A/C=11 Nos, 2.00 Tr. Split A/C=7 Nos, 2.00 Tr. Casset A/C=1 No, Geyser 25 Ltrs capacity=5 Nos,Geyser 15 Ltrs capacity=2 Nos, LED TV 43'=6 Nos,Refrigerator 190 Ltrs=3 Nos,Microwaven 28 Ltrs=1 No.Water purifier=2 No,Tatasky connection=6 Nos, Fitting and fixing Charge of A/C= 23 Nos, Freight charge for A/Cs=23 Nos, and freight for other items=2500) as per Direction of the Department.

Supply, installation, testing and commissining of Hospital utility items(1.5Tr Split A/C=4 Nos,1.8Tr. Split A/C=11 Nos, 2.00 Tr. Split A/C=7 Nos, 2.00 Tr. Casset A/C=1 No, Geyser 25 Ltrs capacity=5 Nos,Geyser 15 Ltrs capacity=2 Nos, LED TV 43'=6 Nos,Refrigerator 190 Ltrs=3 Nos,Microwaven 28 Ltrs=1 No.Water purifier=2 No,Tatasky connection=6 Nos, Fitting and fixing Charge of A/C= 23 Nos, Freight charge for A/Cs=23 Nos, and freight for other items=2500) as per Direction of the Department.

Supply , installation, testing and commissioning of fire fighting and detection system at 200 bedded COVID ICU(1st Floor of Car Parking) at Guwahati Medical college and Hospital, Bhangagarh. Supply and installation of mono ammonium phosphate based dry powder 1.3kg. Capacity fire extinguiser ball-40 Supply and installation of mono ammonium phosphate based dry powder 04kg. Capacity ABC stored pressure type fire extinguiser-7 Supply and installation of mono ammonium phosphate based dry powder 05kg. Capacity ABC stored pressure type fire extinguiser-27 Supply and installation of clean agent gas based 05kg. Capacity ABC stored pressure type fire extinguiser-27 Supply and installation of clean agent gas based 02kg. Capacity ABC stored pressure type fire extinguiser-18 Supply and installation of 4.5kg. Capacity CO2 type fire extinguiser-14 Supply and installation of 2kg. Capacity CO2 type fire extinguiser-2SITC of intelligent fire alarm control Panel 01 loop card inbuilt, 99 addressable points per loop, total addressable devices 198, integrated PSU with battery charger(Make Morley)-1 SITC of addressable semi flush mounting resettable(non breaking glass) MCP, supplied with special reset tool. (Make Morley)-2 SITC of intelligent addressable detector with remote indicator output with base(Make Morley)-28 Supply and fixing of 2x1.5sqmm PVC insulated copper wire on above false ceiling(KEI)-421 SITC of addressable wall mounting sounder cum hooter (Make Morley)-2

Video/Audio Input: IP video input: 32-ch, Two-way audio input: 1-ch, BNC(2.0 Vp-p, 1kΩ),Incoming bandwidth: 200Mbps, Outgoing bandwidth: 160Mbps,Remote connection: 128,CVBS Output:1-ch, BNC(1.0Vp-p, 75Ω) Resolution: 704×576(PAL); 704×480(NTSC),HDMI Output: 1-ch, resolution: 1920*1080P/60Hz, 1920*1080P/50Hz, 1600*1200/60Hz, 1280*1024/60Hz, 1280*720/60Hz, 1024*768/60Hz, Recording Resolution: | 8MP/5MP/3MP/1080P/UXGA/720P/VGA/4CIF/DCIF/2CIF/CIF/QCIF, Audio Output: 1-ch, BNC(Linear Electrical Level, 600Ω), Synchronous Playback: 16-ch, VGA Output: | 1-ch, resolution: 1920*1080P/60Hz, 1600*1200/60Hz, 1280*1024/60Hz, 1280*720/60Hz, 1024*768/60Hz, Live view Playback: 5MP/3MP/1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF /QCIF, Capability: 16-ch@720P, 8-ch@1080P, SATA: 2 SATA interfaces for 4 HDDs + 1 DVD-R/W (default), or 8HDDs, Interface Type: 1 SATA interface, Capacity: Up to 6TB capacity for each HDD, Array type: RAID0, RAID1, RAID5, RAID10, Network Interface: | 2 RJ-45 10/100/1000Mbps self-adaptive Ethernet interfaces, Serial Interface: RS-232, RS-485, Keyboard, USB Interface: 3, USB2.0, Alarm In: 4-ch, Alarm Out: 2-ch, Power Supply: 100 ~ 240 VAC, 6.3 A, 50 ~ 60 Hz, Consumption (without hard disk and POE): ≤ 45 W, Working Temperature: -10 ºC ~ +5 ºC (+14 ºF~ + 131 ºF), Working Humidity: 10 % ~ 90 % (CAMERA NVR 32 CHANNEL,MAKE:HONEY WELL.)-1 Video/Audio Input: IP video input: 16-ch, Two-way audio input: 1-ch, BNC(2.0 Vp-p, 1kΩ),Incoming bandwidth: 200Mbps, Outgoing bandwidth: 160Mbps,Remote connection: 128,CVBS Output:1-ch, BNC(1.0Vp-p, 75Ω) Resolution: 704×576(PAL); 704×480(NTSC),HDMI Output: 1-ch, resolution: 1920*1080P/60Hz, 1920*1080P/50Hz, 1600*1200/60Hz, 1280*1024/60Hz, 1280*720/60Hz, 1024*768/60Hz, Recording Resolution: | 8MP/5MP/3MP/1080P/UXGA/720P/VGA/4CIF/DCIF/2CIF/CIF/QCIF, Audio Output: 1-ch, BNC(Linear Electrical Level, 600Ω), Synchronous Playback: 16-ch, VGA Output: | 1-ch, resolution: 1920*1080P/60Hz, 1600*1200/60Hz, 1280*1024/60Hz, 1280*720/60Hz, 1024*768/60Hz, Live view Playback: 5MP/3MP/1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF /QCIF, Capability: 8-ch@720P, 8-ch@1080P, SATA: 2 SATA interfaces for 4 HDDs + 1 DVD-R/W (default), or 8HDDs, Interface Type: 1 SATA interface, Capacity: Up to 6TB capacity for each HDD, Array type: RAID0, RAID1, RAID5, RAID10, Network Interface: | 2 RJ-45 10/100/1000Mbps self-adaptive Ethernet interfaces, Serial Interface: RS-232, RS-485, Keyboard, USB Interface: 3, USB2.0, Alarm In: 4-ch, Alarm Out: 2-ch, Power Supply: 100 ~ 240 VAC, 6.3 A, 50 ~ 60 Hz, Consumption (without hard disk and POE): ≤ 45 W, Working Temperature: -10 ºC ~ +5 ºC (+14 ºF~ + 131 ºF), Working Humidity: 10 % ~ 90 % (CAMERA NVR 16CHANNEL,MAKE:HONEY WELL.) Seagate (preferred) 3.5-inch, Capacity: 6TB, NVR-Ready, 164 cameras, 550 TB/year, 3 years warranty (Hard Disc for Camera 6TB)-3 2 Megapixel (1920 x 1080) High Resolution, HD720p Realtime Video Recording, True Day / Night, IP66 Rating, IR Range: Up to 30m, Vandal-proof Housing, 3 ROI. IE / Firefox Browsing, CMS control(Bullet camera, Make Honey Well-25 2 Megapixel (1920 x 960) High Resolution, HD 720p Realtime Video, True Day / Night Auto Switch, IP66 Ingress Protection, IR LEDs up to 30m, Vandal-proof Housing, 3 ROI. IE / Firefox Browsing, CMS control(Dome Camera, Make Honey Well)-17 10/100/1000 24 PORT ALL POE SWITCH WITH 2 SFP UPLINK PORT 24 PORT POE SWITCH GIGA (Make: NETGEAR) 10/100/1000 16 PORT ALL POE SWITCH WITH PORTS (183W) 16 PORT POE SWITCH GIGA MAKE: NETGEAR-25 FINOLEX 0.5X4 PAIR UTP CAT 6 LAN CABLE (305MTR) ROLL CAT6 WIRE MAKE: FINOLEX NETRACK 6U/500 CKD WITH GLASS DOOR, FAN PDU.6U Rack-3 MAKE:NETRACK DLINK (RJ45 Connector)-108, PATCH PANEL & PATCH CORD, PATCH PANEL, MAKE: DLINK, PATCH CORD 1 MTR-46, PATCH CORD, MAKE: DLINK, INSTALLATION, COMMISSIONING & PROFESSIONAL ENGINEERING CHARGES, 1” PIPE – BEND- FLEXIBLE PIPE-TIE-46

15 W CEILING SPEAKERS full-Range dual cone premium ceiling loudspeaker.-14 MAKE: BOSCH GOOSENECK MICROPHONE -1 MAKE : BOSCH 240W ALL IN ONE AMPLIFIER -1 MAKE: BOSCH COUNTER COMMUNICATION SYSTEM MAKE: AHUJA-2 1.5 SQMM 3 CORE WIRE IS694 RDSH (100MTR) ROLL (FINOLEX)-685m 1” PIPE – BEND- FLEXIBLE PIPE-TIE-154 INSTALLATION, COMMISSIONING & PROFESSIONAL ENGINERING CHARGES

NEC EPBX SL-2100 16 EXTENSION 2PNT-1 MAKE: NEC SYNTEL DIGITEL PHONE -14 MAKE : PANASONIC 10/20/30 PAIR DP BOX & IDC MODULE KRONE/SURFACE BOX/FACE PLATE/ KEYSTONE JACK/RJ11-4 FINOLEX 0.5X2PAIR TELEPHONE CABLE (90MTR) ROLL-590m 600VA UPS 7AMP BATTERY-1 MAKE:- APC 1” PIPE – BEND- FLEXIBLE PIPE-TIE INSTALLATION, COMMISSIONING & PROFESSIONAL ENGINERING CHARGES

10/100/1000 8 PORT GIGABIT ETHERNET SWITCH-1 MAKE: NETGEAR FINOLEX 0.5X4 PAIR UTP CAT 6 LAN CABLE (305MTR) ROLL-880m 1” PIPE – BEND- FLEXIBLE PIPE-TIE-245CAT6 KEYSTONE UTP JACK WITH DUST COVER WHITE MAKE: D LINK-22 BACK BOX (SURFACE MOUNT BOX) FOR SINGLE & DUAL MAKE: D LINK-15 INSTALLATION, COMMISSIONING & PROFESSIONAL ENGINERING CHARGES

Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 650/1100 V grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required. 3 ½ X 70 sq.mm

3 ½ X 95 sq.mm

3 ½ X 150 sq.mm

3 ½ X 300 sq.mm

3&1/2Cx400sqmm

Supply, installation, tesing and commissioning of Ductable Air conditioning systems with scroll compressor with the following specification: Supply Blue Star Air Cooled ceiling suspended Ductable Air Conditioners with scroll compressor , micro-processor based controller with LCD Display and compatible with R-22 Refrigerant Gas. 11TR Nominal capacity (DSA1321R1)-6 Ductable Out door / Indoor with lifting & Installation with angle frame.-6 VI Pad with anchore & fittings,for Outdoor Units-6 Hard/Soft Drawn Copper Piping interconnecting Indoor & Outdoor units considering 10m for Ductable Unit including suction and liquid, 5/8"-70m, 1.1/8"-70m Drain Pipe with hard PVC with tube insulation 25NB-30m, 32NB-20m Electrical Control Cabling-20m, 7C x 1.5 SQMM Copper-100m, GSS Ducting-290sq.m, 24G-290 sq.m, 22G-50 sq.m Installation/ Nitrogen testing / Vacumising the system for commissioning of Ductable Machine with Refrigerant gas. 11TR Nominal capacity(DSA1321R1)-6 Duct Thermal Insulation with 25 mm thick Al foil faced Glass Wool-260 sq.m Duct Acoustic Insulation with 12 MM thick rigid board insulation.-60m, Al Power Coated Diffusers/Grilles without VCD-5 sq.m, Al Power Coated Diffusers/Grilles with VCD -5 sq.m, Canvass connection -6, SITC of Inline Excle flow fan with others materials.-280 sq.m, SITC of U.V. Light for the coil of IDU, along with Micro Filter.-2 S.I.T.C of ODU Base with Angle, for the Dictable machine.

Supply Installation testing and commissioning of 100 KVA online 3 phase UPS systems with 30 mins battery backup including batteries, interconnecting cables, battery racks etc (analysed rate based on PAR 2020 of DSR

Suppy, Installation, Tesing and commissining of"KIRLOSKAR" make diesel Engine ModelDV12ETA G1 liquid cooled turbo charged with after cooler, developing 900HP liquid cooled, @ 1500RPM, V type electric start, compression ignition, 4 stroke designed to run continously 1500 RPM confirming to IS 10001 ISO-3046, BS-5514 standard with an overload capacity of 10% for one hour in every 12 Hrs.Diesel Engine will comply with present CPCB-II norms and will be directly coupled to a KIRLOSKAR(KOEL GREEN) A.C Generator capable of developing 750KVA/600KW. KOEL GREEN make alternator is suitable for continous operation rated at 1500 RPM, 415V,0.8PF ,50Hz, 3Ph in SPDP enclosure, self excited and self regulated, brush -less, floor mounted with ball or bearings on end shields.The Alternator efficiency is as per IS 4722 & IEC 34-1 standards and will be suitable for tropical condition alongwith AMF control Panel(Genset Model-DV10TAG1,Weight=8300Kg, LXBXH=6800X2300X2713, No . of Cylinders=12. Fuel tank=990 Ltrs.).

Supply and installation,Testing & Commissioning of Terminal Units(Gas Outlets)with Probes/Adaptes as per ISO 9001:2015 & 3 digit CE marked company.The outlet will be equiped with primary and a secondery check valvewith suitable pressure for (O2 Cleared for medical gas and pressure tested,inlet pipe can be swiveled 360 degree for ease of installation as per spesified and directed)

Supply and installation,Testing & Commissioning of O2 flow meter as per ISO 9001:2015 & 3 digit CE marked company made with chrome plated brass bodey,graduated flow tube and cover made of polycarbonate & unbreakable. Adjustable flow by needle valve(know) with micrometric regulation. Humidifier bottle is made of unbreakable polycarbonatematerial and is autoclavable

Supply and installation,Testing & Commissioning of Terminal Units(Gas Outlets)with Probes/Adaptes as per ISO 9001:2015 & 3 digit CE marked company. The outlet will be equiped with primary and a secondery check valve with suitable prepressure for complete all as spesified and as directed for the following: For Compressed air (4Bar)

Supply and installation,Testing & Commissioning of Terminal Units(Gas Outlets)with Probes/Adaptes as per ISO 9001:2015 & 3 digit CE marked company. The outlet will be equiped with primary and a secondery check valvewith suitable pressure for (Vaccume) Cleaned for medical gas and pressure tested,inlet pipe can be swiveled 360 degree for ease of installation as per spesified and directed)

Supply and installation,Testing & Commissioning of ward vaccume unit as per ISO 9001:2015 & 3 digit CE marked company.with Regulator along with vaccume gauge,collection jar of 600 ml capacity reusable plastic collection bottle with over flow safety tap wall mounted type with bracket complete all as spesified and as directed.

Supply fitting and fixing of Copper Pipes as per Medical Grade: Llyod Certified 12 mm od X 0.7mm thickness

15mm od X 0.9mm thickness

22mm od X9mm thickness

28mmX.9mm thickness

42mmX1.0mm thickness

Supply and installation,Testing & Commissioning of area line pressure alarm with display of various faults indications and capable of monitoring maximum 3 medical gas service by means of pressure switches etc with audible warning with automatic reddit when the gas service return to normal as per ISO 9001:2015 & 3 digit CE marked company and as directed for the following area line pressure alarm. 3gas service O2,air and vaccum.

Supply and installation,Testing & Commissioning of isolation valves with brass body with nickel plate valve operating handle suitable for 12mm Od copper pipe to 42mm Od copper pipes with brass adapter as per standard spesification & as per ISO 9001:2015 & 3 digit CE marked company and sirevted for the following isolations. 12 mm od X 0.7mm thickness

15mm od X 0.9mm thickness

22mm od X 0.9mm thickness

28mmX 0.9mm thickness

42mm X 1.2 mm thickness

Ventilator Probe for O2

Low pressure tubings

Supply and installation,Testing & Commissioning of Bed Head Panel 5ft Long as per ISO 9001:2015 & 3 digit CE marked company. These are panels as per customer choice of colour to maintain the aesthetics of the hospital along with accessories like 1No. Of IV hook 1.no. of utility BP Basket 1 No. of Monior tray 1 No of Aluminium Clamp for ward vaccum Unit and 2 no. of 6/16 amp Anti bacterial Switch and sockets.

Supply and installation,Testing & Commissioning of Oxygen Manifold Extendable type10+10 size compatible as per ISO 9001:2015 & 3 digit CE marked company with middle frame with chain of individual Cylinder and high pressure annealed copper tail pipe with 1 end having brass adaptor and other end suitable for manifold non return valve and manifold will have 20 brass non return valve for individual Oxygen cylinder , middle frame with cercumferential MS felt duley powdercoated all as spesified and as directed

Supply and installation,Testing & Commissioning of semi Automatic gas control panel for O2 as per ISO 9001:2015 & 3 digit CE marked company., two stages of pressure regulators will be provided in the control cabinet for pressure regulation . One delivery pressure regulator .

Supply and installation,Testing & Commissioning of 3+3 Cylinder Emergency Oxygen Maniflold as per ISO 9001:2015 & 3 digit CE marked company. with two stage high flow rate regulator With NRV for every cylinder and copper tail pipe with top and middle frame for Oxygen

Supply, Installation, Testing & Commissioning of ANESTIWATA MOTHERSON/ oil free , Scrall Air Compressor machine (10 HP)

Supply Installation , testing and Commissioning of 2000ltrs Air reciever tank

Supply Installation , testing and Commissioning of Air Dryer Capacity 100 CFM

Supply Installation , testing and Commissioning of 3 Stage Bacterial Filter assembly

Supply Installation , testing and Commissioning of pressure reducing system with two numbers pressure regulators

Supply, Installation, Testing & Commissioning of ANESTIWATA MOTHERSON Rotary vann type vacuum Pump with accessories, base mounting,Capacity: 10 HP (0.760 MM/HG)

PLC BASED AUTOMATIC TIMER MANAGEMENT SYSTEM WITH TOUCH SCREEN HMI

Revolving Chair in Nurses Station = 12 nos Toilet Door mat(LG) = 10.2 sqm

Supply and installation of ICU Nurse Station Table of 1200 x 600 x 750 mm with 25mm thick Pre-laminate(anti Bacterial) particle board top finished with 2mm edge lipping with Modesty Panel 18mm thick 450ht PLB modesty panels with necessary brackets with 25mm thick gable ends and cross beam under Structure Support including 65mm dia Grommet hole for Wire Management as per approved shade and design and as directed by the department complete in all levels.

Supply and installation of low height storage unit at nurses station of size 600mm x 600mm x 625 mm including 2 nos pull out tray and the lower part shall consist of storage unit with solid shutters, all made with 18mm BWR grade ply board (greenply/century or equivalent make), inside finished with 0.8 mm white laminate of Greenlam/Century/Merino make and outside and exposed surface finished with 1mm thk Anti bacterial laminate including soft closing hinges and drawer channels Godrej/Hettich/Haffle make for the shutters. The cabinet shall be supported by lockable floor wheel complete as per design and as directed by the department.

Supply and installation of multiple stack of low height storage unit in modules of size 600mm x 600mm x 625 mm(size of one unit) with solid shutters, all made with 18mm BWR grade ply board (greenply/century or equivalent make), inside finished with 0.8 mm white laminate of Greenlam/Century/Merino make and outside and exposed surface finished with 1mm thk Anti bacterial laminate including soft closing hinges of Godrej/Hettich/Haffle make for the shutters complete as per design and as directed by the department. (to be measured as one unit multiplied by total no of units)

Supply and installation of Doffing area Locker of size 600 mm x 420 mm x540 mm with solid shutters, all made with 18mm BWR grade ply board (greenply/century or equivalent make), inside finished with 0.8 mm white laminate of Greenlam/Century/Merino make and outside and exposed surface finished with 1mm thk Anti bacterial laminate including soft closing hinges and drawer channels of Godrej/Hettich/Haffle made for shutters and drawers respectively complete as per design and as directed by the department.

Supply and installation of low height storage lockers unit with solid shutters, all made with 18mm BWR grade ply board (greenply/century or equivalent make), inside finished with 0.8 mm white laminate of Greenlam/Century/Merino make and outside and exposed surface finished with 1mm thk Anti bacterial laminate including soft closing hinges and drawer channels Godrej/Hettich/Haffle make for the shutters including fitting and fixing of 18 mm thick polished granite top complete as per design and as directed by the department.

Supply and installation of Doffing area Locker of size mm x mm x mm with solid shutters, all made with 18mm MDF board (greenply/century or equivalent make), inside finished with 0.8 mm white laminate of Greenlam/Century/Merino make and outside and exposed surface finished with 1mm thk Anti bacterial laminate including soft closing hinges and drawer channels of Godrej/Hettich/Haffle made for shutters and drawers respectively complete as per design and as directed by the department.

Supply and installation of the following furnitrures : Offie table = 2 nos Visitor Chair =2 nos Office Table = 3 nos Visitor cchair = 6 nos Door mat = 2 nos Sofa Set of Premium quality = 2 nos Centre Table = 5 nos Upholstry Fabric in Doctors Lounge table including element (EI)and making charge = 7m Sofa Set of High end Premium quality = 1 nos Sofa Set of Delux quality = 1 no

Supplying, Fixing and Fitting of not less than 50 mm thick wall panelling with 8 mm thk BWR grade Plywood of Greenply/Century make fixed over Gyp steel flanged studs fixed vertically on brick wall at interval of 450mm c/c. The 8 mm thick BWR grade Plywood of approved brand to be fixed on the face with 25mm drywall screw at 300 mm c/c to one sides of 50 mm studs (0.55 mm thk having one flange of 34mm and another of 36 mm made of GI steel with joints staggerred. Another layer of 4 mmthick BWR grade Plywood of approved brand has to be fixed over the 8 mm plywood base with necessary grooves of 4mm x 4mm (as per design) and the 4 mm plywood is to be finished with 1 mm thk laminate of Merino/Greenlam/Century make including all necessary hardwares. The grooves has to be polished with approved colour and complete in all levels as per design and as directed by the department.

Supply fitting and installation of High Resolution (HR) Signage as per the specifications and size as directed by the depaartment at all levels

Supply fitting and installation of High Resolution (HR) Signage as per the specifications and size as directed by the depaartment at all levels

Supplying and stacking of river clay at site including royalty and carriage complete with mixing of organic maure including laying of the good earth at site in layers of 600 mm including dressing and finished upto desired level as per site requirement and as directed.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Matured Trees Plant upto a height of 600 mm

Matured Bauganvilla upto 450 mm

Tribeni Constructions Limited