REPAIR TO JOINERY, FLOOR and SANITARY FITTINGS AT MH AREA AT NAMKUM UNDER GE RANCHI

Amount

Taking down complete existing treatment of roof/ parapet , Mud puska on roof /parrapet including plastering, brick tiles, stone slabs and leeping any thickness including removal etc complete all as specified and directed .

M&L Brushing neat cement slurry (3 Kg of cement per Sq M) mixed with chemical compound in the proportion, chemical compound SUPER LATEX of DR FIXIT of PIDILITE INDUSTRIES LTD, water & cement (1:4:7) or SBR LATEX of STP LTD or other equivalent as per manufacture instructions for bonding of old concrete surface to new concrete all as specified & directed complete all as specified and directed.

M&L PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) mixed with integral water proofing chemical PIDIPROOF LW mixed in proportion 200 millilitre per 50 Kg cement of DR FIXIT of PIDILITE INDUSTRIES LTD, or STP No 1 (LIQUID) of STP LTD in proportion 200 millitire per 50 Kg cement, as in padding, benching,Sunken portion etc on roof surface for corecting/making proper slope on roof, etc complete all as specified and directed.

M&L Rendering 15 mm thick in cement mortar 1:4 on concrete / brick surfaces with liquid water proofing compound @ 200 ml/50 kg per bag of cement or as per manufacturar instruction finished even and smooth without using extra cement over roof / sunken slab /wall complete all as specified and directed NOTE : water proofing liquid will be measured and paid seperately .

M&L for Water proofing treatment on "Non approachable / non accessible roof" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer complete all as specified and directed :- (i) Properly cleaning and drying concrete surfaces. (ii) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm (iii) Applying evenly tack coat of industrial 85/25 grade @ 1.2 kg/ Sqm. (iv) Laying unrolled over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard wt not less than 3kg /Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction. (v) Applying a coat of bitiminous aluminium paint @ 100 Gram / Sq M over & incl a coat of hot air blown grade bitumen of grade 85/25 @ 1.2 Kg/ Sqm duly sanded over polymeric membrane complete.

Supply only water proofing compound (liquid),ISI marked.

Dismantling AC/ CGI/ translucent ( corrugated, semicorrugated,etc), as in roof covering complete all as specified and directed.

Dismantling of roof trusses, purlin, rails fastening, etc, of steel section complete all as specified and directed

M&L roof trusses (framed ), trussed, purlins, rails & fastening and heavy bracket framing (beam, tee, angle, channel, flat, etc) incl distance pieces, cleats , holdfast etc complete all as specified & directed.

M&L for MS flat (wind tie) as roof sheet securing incl distance pieces, cleats etc complete all as specified & directed.

M&L 6 mm thick asbestos cement, corrugated or semi corrugated sheets in roof, walls etc fixed with L type or J-type or cranked hook bolts etc complete all as specified and directed by EIC .

All as per item No 11 above as but exept sheet

M & L Asbestos cement two piece adjustable plain wing ridge 6 mm thick fixed with 'J' type hook bolts etc complete all as specfied and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, Chhaja, etc fixed with self tapping screws complete all as specified and directed

M&L 1.4mm thick Fibre glass reinforced translucent sheeting in roof, walls etc fixed with L-T type or J-type or cranked hook bolts etc complete all as specified and directed

Dismantling of wall/ceiling boards (fibre, pulp, insulation, etc) of any type including cover fillets.

M&L for providing aluminium snap Grid frame work for false ceiling with of size 605X605 mm ,using Main and cross tee of size 36.5mmX25mmX1.4mm,weighing 0.24 kg/RM and 23.5mmX26.4mmX1.4mm weighing 0.191Kg/RM respectively. the snap grid shall be supported at end all along the wall with aluminium anodised angle of size 40mmX25mmX2mm weighing 0.36Kg/RM. The snap grid shall be fixed to ceiling supporting hangers consisting of 2mm dia MS wire/GI wire, J bolts, nuts and washers as per manufacturer's complete all as specified and directed

M&L 4mm thick non asbestos fibre designer cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws.

M&L 4mm thick asbestos cement plain building boards fixed to timber framework with screws.

S&F 2nd class hardwood plain fillets, square, rectangular or rectangular in section, clean sawn secured with nails sectional area exc 13 & n exc 25 Sqcm complete all as specified and directed

Taking down chowkats or frame with shutters (without taking off shutters from the frames) n. Exc 1.5 Sqm each

All as per item No 21 above but exc1.5 Sqm but n.exc. 4 Sqm.

Taking down shutters of any description n exc 1.00 Sqm each complete all as specified and directed

All as per item No 23 above but exc 1 Sqm & not exc 2 Sqm each

Refixing of shutter of any description exc 1 sqm and n exc 2 sqm in same opening complete all as specified and directed

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube supplying & fixing in opening as per specified & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame wealded/sealed to the stiles & rails with sutable PVC sheet beading and jointed togeather with solvent cement, fix in frame complete all as specified and directed

S & F 2nd class hardwood plain solid straight chowkats and frames wrought framed rebates on the solid, rounded or chamfered put together with glue pinned at joints supplied and fixed.

M&L for hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 Gde E-165

M & L cement concrete type C - 1 (1:3:6) using 20 mm graded stone aggregate as in bed blocks,fillings for holdfast etc complete all as specified and directed.

M/L 35 mm thick Plain framed, paneled shutter (three panel) with lock rail and panel of 12mm plywood commercial on both faces. The size of rail and style as per IS: 1003(Part - 1), complete all as specified and directed.

S & F 30 mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides supplied and fitted to chowkats.

S & F 35 mm thick 2nd class hardwood glazed and skeleton shutters of 8 panels, divided into squares with plain, chamfered or rounded, mitred & rebated sash bars and prepared to receive glass, gauze etc edges of framing plain chamfered or rounded fitted with cat and mitred beads for securing glass etc fitted to chowkats for doors, etc complete, size of member of shutter as specified in SSR Part -I, Sec 8, clause 8.20 (a). Sample of shutter can be seen in GE's office.

S & F 30 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (with sash bars) edges of framing plain chamfered or rounded fitted with cat and mitred beads for securing glass etc fitted to chowkats for windows, ventilators,etc complete, size of member of shutter as specified in SSR Part -I, Sec 8, clause 8.20 (b).

S&F block boards 18/19mm thick grade 2 quality, interior grade, commercial type for cupboard shutter, shelf, etc complete all as specified and directed

S&F in repair 12mm thick pre-laminated particle board interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for cupboard shutter, shelf, etc complete all as specified and directed

S&F steel windows with side hung shutters incl projecting type hinges with one no MS flat iron 25x3 mm of appx 200mm length and two nos MS Tower bolt 150mm long and one peg stay on each leaf complete with glazing bars, dovetailed or welded complete all as specified and directed

All as per item No 37 above but without glazing bars complete

S&F steel window, ventilators, fixed type, with glazing bars

S&F framed work as in doors or gates of angle or other section with guesset plates complete doors etc to be prepared to hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging, also fastening and fixing complete all as specified and directed

S&F 1.00mm thick Mild steel, plain, black sheet in covering to door shutters; covering to door chowkats (frames) cut to size edges beaded if directed, holes punched;incl round headed screws, clout nails or rivets and fixed to wood or steel members, etc.,with plain 40 mm lap joints or welded/riveted seams including bending, turning up,mitred angles, stopped ends, outlets, etc. as reqd complete all as specified and directed

S&F framed work such as grills gratings etc with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars, barred iron doors, ladders framed, baluster walk ways, railings, framework of water tanks & similar wk conforming to Fe410-0 or Fe310-0 .

S&F Galvanised mild steel wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks etc complete all as specified and directed

S&F in repair Galvanised mild steel wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks etc complete all as specified and directed.

Hacking out old boken glass(any thickness, size, quality or description) from wooden frames/steel frames glazed with oil putty or fixed with beads complete all as specified and directed

S& F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n. Exc 0.5 Sqm in each pane.

S & F 3 mm thick frosted glass pin head type and glazing with oil putty in squares exc 0.5 Sqm in each pane etc complete all as specified and directed.

S & F Aluminium anodised barrel tower bolts of extruded section and fixed 200 mm long.

S & F Aluminium anodised barrel tower bolts of extruded section and fixed 125 mm long.

S & F Aluminium anodised handles of extruded section and fixed 125 mm long.

S & F 100 mm size Butt hinges medium weight cold rolled mild steel and fixed.

S & F 75 mm size Butt hinges medium weight cold rolled mild steel and fixed.

S&F 100mm long hasp & staple aluminium anodised wire type, incl bolt to hinge plate and fixed with screw complete all as specified and directed

S&F small fitings of 2nd class hard wood such as brackets of any type, latch and hing block shape door, window stops and the like incl all necessary labours articles not exc 200 cucm each.

S & F 250 mm long mild steel sliding door bolt with hasp, staple( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed.

MS ordinary rat tail rod pattern springs 200mm, including roller and roller plate complete all as specified and directed

M&L preparation of new wooden surface any description over 10 cm width or girth and applying two coat synthetic enamel paint over a coat pink primer complete all as specified and directed.

M & L preparation of new steel surfaces any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete all as specified and directed

Taking down cement plaster on wall of any description incl racking out joints hacking for key and scrubbing down with water complete all as specified and directed

Demolition of brick work build in cement mortar including all quoins, arches, pillars, complete all as specified and directed.

M&L brick work with sub class 'B' brick straight or curved on plan exc 6m means radius build in cement mortar 1:6 complete all as specified and directed

All as per item No 61 above but except bricks

M&L 15mm thick rendering on fair faces of bk /concrete surfaces in cm (1:6), finished even and fair (Without using extra cement ) complete all as specified and directed

M&L three coat of white wash on newly prepared surfaces on wall , etc complete all as specified and directed.

M&L for preparation of new plastered wall surface applying two coat of "Birla White wall care putty"or" JK Wall Care Putty "to make the entire surface free from undulations complete all as specified and directed

M&L Preparing New putty wall surfaces, priming plastered and other surfaces with alkali resistant primer and applying two coats of oil bound distemper of any shade on walls surfaces

Demoliton of cement concrete in ground floor paving n exc 15cm thickness ( below or above ground level ) complete.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed

M&L Cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub base etc complete all as specified and directed

M&L Cement concrete 1:2:4, type B-1 (using 12.5 mm graded stone aggregate) as in levelling course, coping, window cill etc complete all as specified and directed.

M & L 40 mm thick PCC type B - 1 1:2:4 using 20 mm graded stone aggregate as in flooring finish even & smooth using extra cement complete all as specified and directed

M & L for 75 mm thick PCC 1:3:6 type C-2 using 20mm graded stone aggregate including finished surface even & fair without using extra cement as in plinth protection including necessary form work of edge all as specified and directed. Note: 10mm wide and 75mm deep joints shall be made at 3 mtr intervel and at each corner and the same shall be filled with using bitumen 85/25 and sand in the ratio 1:3.

M&L for non skid coloured ceramic tiles 300 x300 x7mm thick in floors etc over & including 15mm thick screed bed in CM 1:4, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed

M&L coloured ceramic glazed tiles 300x200x6mm thick as in dado/skirting etc including 10 mm thick rendering in CM 1:4, set & jointed in neat cement slurry & pointed in white or coloured cement slurry & pointed in white or coloured cement

M&L coloured ceramic glazed tiles 375x250x7mm/ 450x300x7mm thick as in dado/skirting etc including 10 mm thick rendering in CM 1:3, set & jointed in neat cement slurry & pointed in white or coloured cement slurry & pointed in white or coloured cement.

M&L for joint free non skid coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc over & including 15mm thick screed bed in CM 1:4, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed

M&L for joint free non skid coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in, skirting, dado, etc incl 15mm thick rendering in CM 1:4, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed

M&L for 9-10mm thick Light coloured vitrified ceramic tiles of size in floors, not exceeding 0.36 sqm set & jointed in neat cement slurry and pointed in coloured cement to match over & including 20mm thick screed bed in CM 1:4 complete all as specified & directed.

All as per Item No 78 but as in Skirting with 10mm thick rendering in CM 1:3

M&L machine cut kota stone slab flooring 18-20mm thick over & including 20mm screed bed in CM 1: 4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

All as per Item No 80 but as in Skirting with 10mm thick rendering in CM 1:3

Demolition of cement concrete reinforced as in chullah hoods , shelves, cover slab and plate form etc complete all as specified and directed

M&L for RCC as in kitchen platform, shelves, cover slab type BO 1:2:4 (12.5 mm graded aggregate) including necessary form work complete all as specified and directed

S&F mild steel deformed bars 8 to 10mm dia and over cut to length bend to shape required including cranking bending spirally for hooping for columns, hooking and binding with and including mils steel wire (annealed) not less than 0.9 mm dia quality conforming to Fe-410-S or F-410-0 etc complete all as specified and directed.

M&L marble work of any shade 16 to 18mm thick in cooking platform, steps, windowcills, etc over and incl 15mm thick cement screed base in CM 1:4 laid and jointed with white cement slurry mixed with admixture of pigment to match the shade of the slab incl rounding of slab & demolition of old slab where directed complete all as specified and directed.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed

S&F anodised aluminium door shutters, aluminium shutters, aluminium section weighing 0.55 Kg/m including necessary joining joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, anodised alumnium snap beading, screws etc. complete all as specified and directed

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc. complete all as specified and directed

M&L double action floor spring for aluminium doors hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including necessary cutting & making good to floor as per existing complete all as specified and directed. Make - Kelwyn / Amar

S&F cast brass fanlight pivot with plate size 25mmx65mm and suitable for shutter of 35mm thick complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples

M&L 9mm thick Prelaminated particle board,interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with alumunium frame work.

S&F 4.00 mm thick plain Sheet glass, area exc 0.5 sqm in each pane and fixed to aluminium frame work etc complete all as specified and directed.

S&F 4.00 mm thick plain Sheet glass, area n exc 0.5 sqm in each pane and fixed to aluminium frame work complete all as specified and directed.

S&F 4 lever brass mortice lock vertical type size 65mm long complete all as specified and directed.

Taking down aluminium doors shutters only (area exc 1.0 sqm but not exc 2.0 sqm each) and dismantling all members and reassembling the same with and including new screws, new rubber gasket, new aluminium beads & cleats of existing make and also refixing the handles & mortice locks in existing position with and including new screws including refixing the door shutters in same opening complete all as specified & directed.

S&F in repairs IVC hand shower (Health faucet) with 8mm dia, 01 (one) metre long PVC tube and wall hook with plastic body complete all as specified & directed.

S&F in repair 500 Ltrs capacity rotational moulded polythene water storage tanks in two layer cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I

S&F in repair 1000 Ltrs capacity rotational moulded polythene water storage tanks in two layer cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I

S&F PVC ball valve 20mm dia with epoxy coateed aluminium rod and high density ball (minium weight 210 gms) complete all as specified and directed

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen with plugs, washers, waste coupling, waste pipe incl bedding in cement mortar to dwarf wall or incl fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as directed and specifed .

Taking up or steel tubing & connections including cleaning for refixing bore of pipe 15mm etc complete all as specified and directed

All as per item No 102 above but 20mm bore

All as per item No 102 above but 25mm bore

S&F tubes medium grade galvanised with all fittings & fixed complete to walls & ceiling or laid in floors 15mm bore etc complete all as specified and directed

All as per item No 105 above but 20mm bore

All as per item No 105 above but 25mm bore

Refixing old galvanised steel tubes & connections on wall 15 mm bore complete all as specified and directed .

All as per item No 108 above but 20mm bore

All as per item No 108 above but 25mm bore

S&F in repair for Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed .

S&F in repair for Gun-metal, globe or gate valves 15mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed .

S&F in repair bib tap 15mm fancy type of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed .

S&F in repair bib tap 15mm chromium plated fancy type long shank with crutch butterfly handle, screw down screwed for iron pipe or for brass ferrule etc complete all as specified and directed .

S&F in repair stop valve 15mm chromium plated screw down, high pressure with crutch or butterfly handle, screwed fboth ends for or iron pipe or for unions and fixed complete all as specified and directed

All as per item No 115 above but two way angle cock

S&F in repairs15mm dia pillar tap cost copper alloy fancy type with capstan heads chromium plated screwed down high pressure with or without letered "Hot or Cold" high pressure with long screwed shanks & fly nuts screwed for iron pipe etc complete all as specified and directed

S&F in repair 15mm dia central hole basin mixer with U shaped round cated spout with 450mm long braided hoses (hot & cold)

S&F in repair 15mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed compete all as specified and directed..

S&F in repairs 15 mm dia concealed type stop valve fancy type chromium plated etc complete all as specified and directed

S&F in repair Brass chromium plated shower rose 125mm size fancy type with or without swelves joint fixed to iron pipe etc complete all as all as specified and directed

S&F in repair Vitreous china wash down water closet pan ( pedestal pattern), white (excluding fixing bolt, flushing cistern and flush pipe) but including P or S trap, sheet cover of white colour complete all as specified and directed

S&F in repair MS conduit curtain rod with PVC coating fancy type drafry rod 20mm dia of any colour as approved design and fixed to wall complete all as specified and directed.

S&F fancy type sofia brakcet for the curtain rod (suitable for 20mm dia curtain rod) of any approved colour and design complete all as specified and directed

S&F in repair vitreous china squatting pan, Orrissa pattern size 580x440mm white with PVC 'P' or 'S' trap with integral foot rest of any pattern incl connection to trap & to flushing pipe, antisyphonage pipe etc making good to floor complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back, size 550x400 mm incl chain and plug and porcelain stopper, brackets, waste pipe incl cutting for and pinning in ends of brackets or erecting stand including dismantling

S&F in repair PVC connection 450mm long with two PTMT nuts (Prayag)

S&F in repair CP towel rail, 20mm dia, D type,60cm long complete all as specified and directed

S&F in repair PVC flushing cistern 10 ltr capacity including bracket fixed to wall & flush pipe complete of make-Parryware-slimline/ Commander-water bird

S&F in repair, plastic water closet seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device for pedestal pattern WC white colour.

S&F in repair 32mm bore waste coupling of PTMT (half or full threaded) (Min wt 45 gms) Complete all as specified and directed.

S&F in repair 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6kgf/sqcm Complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joint laid in trenches complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joint laid in trenches complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joint fixed to wall complete all as specified and directed.

S&F PVC(SWR) 110 mm bends any radius.

S&F PVC (SWR) vent cowl 110mm bore

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

BHARATI ENTERPRISES

M K Enterprises