ADDITION /ALTERATION TO CERTAIN SMQS AT AF STN NARELA UNDER GE (AF) GURGAON

Amount

Demolition of cement concrete (un-reinforced) of any description & in any position not specifically provided complete including dismantling of floor tiles etc complete all as specified.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition ) of any description in any position not specifically provided complete complete all as specified.

Demolition of brick work or rubbled stone masonry including all quoins arches , pillars etc built in cement mortar and including removal from the site complete all as specified.

Demolition of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc.

Demolition of Mud in roofs, any thickness including plastering and leeping, (whether full thickness removed etc including roof tiles complete all as specified and as directed.

M&L for 75 mm thick cement concrete (1:4:8) type D-2 with using (40 mm graded stone aggregates) as in sub base of flooring etc complete all as specified.

M&L for 40 mm thick plain cement concrete flooring type B-1, 1:2:4 (20 mm graded crushed stone aggregate) finished even and smooth without using extra cement complete all as specified.

M&L Plastic dividing strips, 1.5mm thick and 22 mm wide inserted in position and confirmed to design all as specified.

M&L for cement concrete (1:2:4) type B-0 (using 12.5 mm graded stone aggregates) 25 mm thick as in sub base of flooring/tiles etc complete all as specified.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregates) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified.

M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:4) for bedding of tiles complete all as specified.

M&L 10 mm thick rendering in cement mortar (1:3) on vertical surfaces for backing of tiles etc complete all as specified.

M&L for Non - skid (joint free) coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L for Glazed ceramic coloured tiles in vertical surface 600X300X 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite complete all as specified.

Providing edge moulding to 18-20 mm thick stone(any description) of counters vanities etc, including machine polishing to edge to give high gloss finish etc. Complete to Granite stone any description.

M&L for 40 mm thick PCC (1:2:4) type B-0 (Using 12.50mm graded stone aggregate) as in roof padding complete all as specified & as directed.

M&L for 15 mm thick plaster in cement mortar (1:4) mixed with water proofing compound on roof slabs finished even and smooth (without using extra cement) after cleaning of roof surfaces with wire brushes complete all as specified. Notes : WPC shall be measured and paid seperately.

M&L for water proofing treatment with APP (Atactic Polypropylene) modified polymeric prefabricated five layer membrane over roof consisting of cleaning of concrete or plaster surface of roof & parapet walls and applying evenly a bitumen primer confirming to IS 3488 @ 0.40 Kg per sqm laid using buten torch and sealing all joints of APP modified polymeric water proofing membrane minimum weight 3.6 kg/sqm reinforced with non woven polyester fabric (weight not less than 160 grams per sqm) unrolled and bonded to substrata with logitudinal and end laps 100 mm and 150 mm respectively as per manufacturer's instructions complete all as specified.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified.

M&L for providing plain cement concrete (1:2:4) type B0 (using 12.5 mm graded crushed stone aggregate) as in coping or roof kerbs on roof chamfered on edge rounded or chamfered on edges including trowelling slightly complete all as specified.

M&L for Cement concrete tiles 25cm x 25cm x 22 mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished, set with grey cement and pigments over 15mm thick cement screed bed in cement mortar 1:4 complete all as specified and directed.

M & L for applying two coat of bitumenous aluminum paint over APP membrane complete all as specified and directed.

Removing bldgs demolished materials / debries exc. 1.50 km but n exc. 5 km and depositing where directed.

M&L for brick work with sub class 'B' old size brick, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:6 etc complete all as specified.

M&L for half brick work with sub class 'B' old size brick, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:4 etc complete all as specified.

M&L for providing reinforced cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified.

Formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work not exceeding 200 mm thick rough finished in flat surface complete all as specified.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 5 cm but n exc 10 cm wide rough finished complete all as specified.

M&L for rendering 15 mm thick in cement mortar (1:6) on brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified.

M&L for 15 mm thick plastering in two layers (10+5) mm in cement mortar (1:4) on brick or concrete surfaces including rendering on fins, fascias, chajja, parapets etc and finishing the surfaces even and fair (without using extra cement), top layer shall be with WPC as per manufacturer's instruction and complete all as specified. Note: WPC shall be measured and paid separately.

M&L rendering 10mm thick in cement mortar (1:3) as in ceilings finished even and smooth (without using extra cement) complete all as specified.

M&L for Rough Cast plaster on brick walls consisting under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is in plastic state the Rough cast mixture consisting of crushed stone or fine gravel mixed of size 6 mm with coarse sand and cement in the ratio1:1:1 shall be applied and finish even including necessary grooving complete all as specified and directed.

Supply only intergral water proofing compound ISI Marked complete all as specified.

M&L for preparation of newly plastered or unplastered/undecorated surface of wall and applying two or more coat distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre over a coat of primer, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified.

M&L for preparation of plastered or unplastered old decorated surface of wall by complete removal of existing treatment by mechanised sander of berger paints or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling of holes and cracks with with suitable material like cement or plaster of paris etc and thereafter applying two or more coat distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre over a coat of primer, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified. Note : (a) Stage for Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes. (b) Material shall be procured from manufacturer and work shall be got executed through authorised applicator.

M&L for preparation of newly plastered or unplastered/undecorated surface of ceiling and applying two or more coat distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified.

M&L for preparation of plastered or unplastered old decorated surface of ceiling by complete removal of existing treatment by mechanised sander of berger paints or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling of holes and cracks with with suitable material like cement or plaster of paris etc and thereafter applying two or more coat distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre over a coat of primer, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified. Note : (a) Stage for Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes. (b) Material shall be procured from manufacturer and work shall be got executed through authorised applicator.

M&L for preparation of newly plastered surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified.

M&L for preparation(complete removal of existing treatment) of old decorated external wall/ceiling surface of existing treatment by scrapping with Trucare Wall Sander : L-01/H-01 (having mechanical vaccum mechanism) having RPM not less than 1500, sand pad of 80 grit having dia of 7"/9" to make the surface free from dust, loose paint etc or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on wall/ceiling surface including filling of holes and cracks with with suitable material like cement or plaster of paris etc thus make surface smooth upto 4th storey buildings complete all as specified and as directed. Note : (a) Stage for complete removal of existing surface & Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes. (b) Material shall be procured from manufacturer and work shall be got executed through authorised applicator.

M&L for guniting work to RCC work in column, flooring, side walls, beam, slab, etc by removing loose concrete cover etc, cleaning of surface with wire brush and applying epoxy paint to rusted reinforcement and S&F welded wire mesh fabric or wire net less than 95 X 95X 3 mm adhesive, plaster grade for concrete admixture 1 part of cement and 3.5 part of sand and average thickness 40 mm and making the surface even including 15mm thick plastering in cement mortar (1:4) on brick or concrete surfaces including finishing the surfaces even and smooth, without using extra cement plumb and making surface true to geometry in line and including necessary form work to be carried at upto double storey building Note.- Where ever reinforcement required will be measured and paid seperatly etc complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc (Distrubed surface of wall shall be make good by the contractor. The rate quoted shall be deemed included for the same) complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc (Distrubed surface of wall shall be make good by the contractor. The rate quoted shall be deemed included for the same) complete all as specified.

Taking down shutter of any description exc 1 Sqm and n exc 2 Sqm and removing from site.

S&F for Pressed steel frames 125X60mm (made out of 1.25mm thick MS Sheet) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified.

S&F for Pressed steel frames 105X60mm (made out of 1.25mm thick MS Sheet) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified.

M&L cement concrete (1:3:6) type C1, (using 20 mm graded stone aggregate) as in filling of door frames of pressed steel and in bed blocks etc complete all as specified.

S&F factory made 35mm thick flush shutters , solid core construction with block board core and plywood face pannel commercial type on both faces complete all as specified.

S&F factory made 35mm thick 2nd class hardwood glazed and skelton door shutters, open rebated and prepared to receive glass, gauze, (without sash bars) edges for framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-1 section 8 clause 8.24 (a) fitted to chowkats complete all as specified.

S&F solid PVC door frame of size 50mm X47mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS square tube supplying and fixing in opening as per specification and drawing.

S&F factory made PVC shelter panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of prelam PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable prelam PVC sheet beading and joined together with solvent cement , supplying and fixing in the frame at site as per specification & drawing as specified.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple including necessary beading complete all as specified.

S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple including necessary beading complete all as specified.

S&F 100 mm Butt hinges, Stainless steel and fixed complete all as specified and as directed.

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified.

S&F 150mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified.

S&F 250 mm long aluminium alloy anodised sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast sections or cast aluminium alloy complete all as specified and as directed.

S&F 300mm, ordinary rat tail made of brass rod pattern springs including roller and roller plate complete

S&F 150 mm size extruded aluminium alloy handles fabricated type anodised and fixed.

S&F floor door stopper 140mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor.

S&F powder coated anodized aluminum frame for partition, doors, windows, ventilations with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F powder coated Anodised aluminium window and ventilator shutters, fixed/side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

S&F for 4.80/5.0 mm thick frosted glass ordinary quality and glazing each pane n exc 0.50 Sqm fixed with neoprene rubber gasket in aluminium frame work complete all as specified.

Hacking out old broken glass (any thickness, size, quality or escription) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F sheet glass 4 mm thick ordinary quality and glazing with oil putty, rubber strip or wooden beads complete all as specified.

S&F mild steel Godrej pattern cupboard with back, sides, top, bottom, 02 shelves & mild steel shutter two leaves with frame , incl necessary fittings of 18 gauge MS sheet with locking arrangement and handle etc all as per Godrej pattern with duplicate keys including necessary fittings & 19mm stainless steel rod for hanging cloths & two coats of spray painting over a coat of red oxide zinc chromate primer complete. The frame of cupboard to be fixed to wall with 6 Nos fasteners.The cost of fasteners & grouting them is deemed to be included in unit rates complete all as specified and as directed. Note:- Superficial area shall be measured, Approx Size (900x1900x600mm) .

Dismantling boarding of any description , fixed in any position with nails complete all as specified and as directed.

Supply & Fixing of 18 mm thick 100% solid WPC (Wood Polymer Composite) plain board (minimum density 650 Kg/Cum) fixed with screws, solvent cement/adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by Engr-in-Charge. (Make: Rajshri Plastiwood/Equivalent)

Supply & Fixing of 18 mm thick 100% solid WPC (Wood Polymer Composite) board (minimum density 650 Kg/Cum) of one side Prelam/Rigidlam and other side balancing laminate colour to make kitchen cabinet shutter/drawer front shutters complete as per specifications and as directed by Engr-in-Charge. (Make: Rajshri Plastiwood/Equivalent from list of makes of CA.

Supply & Fixing of auto closing hinges openable at 0 degree for kitchen cabinet shutters complete as per specifications and as directed by Engr-in-Charge.

Supply & Fixing of stainless steel decorative handles 100 mm size for cupboard shutters complete.

S&F 150 mm tower bolt, Stainless steel and fixed complete all as specified.

S&F 25 mm outer dia medium weight pipe made out of stainless steel 304 grade, including decorative ornamental knobs at both ends and one set of ornamental decorative Stainless steel clamps to fixed to walls complete all as specified.

Dismantling of cast iron pipe up to 100 mm dia, jointed in cement mortar and taking out in trenches/Wall as required etc complete all as specified.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls complete all as specified.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches or floor complete all as specified.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls complete all as specified.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches or floor complete all as specified.

S&F 75 mm dia PVC (SWR) vent cowl complete all as specified.

S&F 110 mm dia PVC (SWR) vent cowl complete all as specified.

S&F 110 mm dia PVC (SWR) bends with rubber rings joints fixed as required complete all as specified.

S&F 75 mm dia PVC (SWR) bends with rubber rings joints fixed as required complete all as specified.

S&F 110 mm dia PVC (SWR) junction single, (Single T) equal or unequal with rubber rings joints fixed as required complete all as specified.

S&F 75 mm dia PVC (SWR) junction single, (Single T) equal or unequal with rubber rings joints fixed as required complete all as specified.

S&F 50 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints including bend, tee, laid in trenches/ floors/walls complete.

S&F Salt-glazed stoneware gully traps (150X150) mm, square or round mouthed, type 'P' complete all as specified.

M&L PVC (SWR) 75 mm floor trap plain with grating including jointing with solvent cement complete all as specified.

S&F PVC (SWR) 'P’ trap 125 mm complete all as specified.

S&F 110mm PVC (SWR) WC connector bent type complete.

Taking up or down steel tubing 15mm bore and connection including cleaning for refixing or removal to store. complete all as specified.

All as per item No. 93 here-in-before but 20mm dia .

Cutting chases, pinning in. making good to facings where required andpointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall etc complete all as specified.

S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified.

Supplying and laying of 25mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supply and fixing in CPVC 20mm Brass Elbow

Supply and fixing in CPVC 20mm Brass Tee

Supply and fixing in CPVC 20mm Male Brass Threaded Adaptor (MTA/ MBTA)

Supply and fixing in CPVC 20mm Female Brass Threaded Adaptor (FTA/ FBTA)

Supply and fixing in CPVC 25mm Tank Adaptor

Supply and fixing in CPVC 20mm Union

Supply and fixing in CPVC 25mm Union

Supply and fixing in CPVC 20mm Ball valve

Supply and fixing in CPVC 25mm Ball valve

S&F in repair 20 mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified.

S&F in repair white vitreous China wash down water closet pan (pedestal pattern), and trap (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc. complete all as specified.

S&F in repairs PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action type with inlet ball valve and float, handle with & including bracket and PVC flush pipe 32 mm bore complete all as specified.

S&F in repair vitreous china pedestal pattern wash hand basin (flat back) white of size 550x400mm including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed including cutting for and pinning in ends of brackets complete all as specified.

S&F 32 mm dia brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified.

S&F Soap dish of chromium plated or stainless steel fixed to wall with chromium plated brass screws.

S&F in repair PVC connection 450 mm long suitable for 15 mm GI pipe with two brass nuts & rubber washers complete all as specified.

S&F brass CP mixer for mixing hot & cold water screwed down for iron pipe 15 mm dia and fixed complete with water saving aerator complete all as specified.

15mm Stop valves, fancy type, chromium plated with long shank and cup (concealed type), high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. ®

S&F in repair 15 mm dia angle valve, cast copper alloy screwed down high pressure, fancy type chromium plated screwed both ends for iron pipe or unions complete all as specified.

S&F in repair bib taps long body, brass, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket with water saving aerator complete all as specified.

S&F in repair pillar taps , cast copper alloy, with capstan heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for 15mm bore iron pipe and fixed complete all as specified.

S&F in repair chromium plated shower roses 125 mm size with or without swivel joints of standard size including fixing to 15mm steel pipe or union complete all as specified.

S&F in repair Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.

S&F in repair 100 mm chromium plated grating complete all as specified.

S&F chromium plated health faucet telephonic type with 8mm dia, 1 meter long CP flexible with wall hook and jet of approved make, suitable for 15 mm bore iron pipes or for unions and fixed complete all as specified.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified.

Dismantling of existing water tanks of steel/PVC/AC of capacity exceeding 250 liters but not exceeding 500 litres complete all as specified.

S&F for rotational moulded polyethylene water storage tanks 1000 ltrs capacity (cylinderical vertical with closed top) hoisted and fixed in position all as per SSR Part I complete all as specified.

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including one number chromium plated waste fittings 40 mm dia & waste pipe complete all as specified and as directed.

S&F kitchen plate rack stainless steel 1 mm thick of size 60cmx75cm complete fixed to brick/concrete wall, with screw including rawl plug complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

S&F rolled mild steel in framed work as in doors or steel gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing conforming to Fe- 290.Gde-E-165 complete all as specified.

S&F 1.60 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for cooler stand, doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

M&L Cutting holes not exc. half brick in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with selftapping screws as specified & directed.

M&L preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L prepration of new Steel surfaces of any description, not otherwise described, over 10cm width or girth & applying two coats of synthetic enamel paint complete all as specified

M&L for preparation of old painted surfaces of wood and wood based material of any description over 10cm width or girth by cleaning, sand papering,brushing etc , filling in cavities and cracks etc with approved filler and applying one coat of synthetic enamel paint to give an even and smooth surface having no sign of brush marks complete all as specified.

S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F Hard drawn steel wire fabric weight per square metre n. exc 4kg cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt

S&F door seal bottom with aluminium plate and rubber insulation 42'' x 1.5'' complete all as specified.

M&L 100 mm thick PCC 1:4:8 tybe D-2 using 40mm stone aggregate as in subbase.Complete all as specified

M&L for screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:4) for bedding of tiles complete all as specified.

M&L for 22-25 mm thick chequered designer coloured tiles (matt/glass finish), size, colour and shape as approved by GE, set and jointed in neat cement slurry and pointed with coloured cement to match etc complete all as specified as directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L for preparation of new concrete surface and applying two coat of synthetic enamel paint exc 10 cm girth or width not other wise described over a coat of primer etc complete all as specified.

Taking down carefully copper/aluminium point wiring (light, Fan, Socket or power) fitting such as switches, ceiling roses, pendents, regulators, sockets etc complete removing material to store for keeping in safe custody for reuse or taking in schedule of credit and making good disturbed surfaces of walls, floors etc all as specified as directed.

Dismantling and taking down fluorescent tube light Single/double of any wattage or size street light fittings for repair or replacement of burnt/worn out accessories or carrying to MES store for reuse or taking in schedule of credit as directed .

Taking down unserviceable sub main wiring of any type/size including wires, conduits, bends,tees/ battens etc complete all as specified and directed by Engr-in-Charge.

Taking down unserviceable MCB, MCCB DB's/AC's box with MCB/MCCB to deposit in store for keeping in safe custody for reuse or taking in schedule of credit of any size/rating complete all as specified and directed by Engr-in-charge.

M & L for concealed point wiring complete with PVC insulated and unsheathed FRLS cable of 1.5 sqmm (nominal area) with multi stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit ISI marked medium grade not less than 20 mm dia, with MS stove enamelled sunken boxes (normal and modular type as required) including earth dolly with plastic laminated sheet top cover (cover plate with frame in case of modular) of approved make and colour including 1.5 sqmm multi stranded FRLS copper conductor cable of green colour as continuous earth wire with lugs and accesseries and making good disturbed surfaces of walls/floor etc complete all as specified and directed for the followings :-

One light point controlled by one,one way switch.

One ceiling fan/exhaust fan/Air ciculator /bell point controlled by one way switch.

Socket 3 pin 5 Amps on the same board, complete all as specified.

Socket 3 pin 5 Amps on independent board , complete all as specified and directed.

All as per above item No 151 here in before but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed, FRLS cable for 15 Amp socket outlet on independent board including 2.5 sqmm multi stranded copper conductor cable of green colour as continuous earth wire with lugs etc as required complete all as specified and as directed.

S & F in replacement of sub main wiring with PVC insulated, FRLS unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 2.5 sqmm (Nominal area) drawn in and including PVC conduit of suitable size as directed with and including one run of 2.5 sqmm multi stranded copper conductor single core PVC insulated, unsheathed cable of green colour as continuous earth wire including lugs etc connected and tested complete all as specified and as directed. Note: (i) Two runs of 2.5sqmm cable and one run of 2.5 sqmm cable of earth continuity conductor and conduit shall be a unit length.

S & F in replacement of sub main wiring with PVC insulated, FRLS unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 4.0 sqmm (Nominal area) drawn in and including PVC conduit of suitable size as directed with and including one run of 4.0 sqmm multi stranded copper conductor single core PVC insulated, unsheathed cable of green colour as continuous earth wire including lugs etc connected and tested complete all as specified and as directed. Note: (i) Two runs of 4.0 sqmm cable and one run of 4.0 sqmm cable of earth continuity conductor and conduit shall be a unit length.

S & F in replacement of sub main wiring with PVC insulated, FRLS unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 10 sqmm (Nominal area) drawn in and including PVC conduit of suitable size as directed with and including one run of 10 sqmm multi stranded copper conductor single core PVC insulated, unsheathed cable of green colour as continuous earth wire including lugs etc connected and tested complete all as specified and as directed. Note: (i) Two runs of 10 sqmm cable and one run of 10 sqmm cable of earth continuity conductor and conduit shall be a unit length.

S&F of socket outlet 5 pin 5 Amps 240 volts AC 50 hz ISI marked flush type complete all as specified and directed by Engineer-in-Charge.

S&F of socket outlet 2-in-1, 6 pin 5 amp and 15 amps 240 volts AC 50 hz ISI Marked all as specified and directed by Engineer-in-Charge.

S&F of switch piano type 5 amp one way 240 volts AC 50 hz ISI Marked complete all as specified and directed by Engineer-in-Charge.

S&F of switch piano type15 Amps one way 240 volts AC 50 hz ISI Marked complete all as specified and directed by Engineer-in-Charge.

S&F of bell push flush type 5 amp one way ISI Marked complete all as specified and directed by Engineer-in-Charge.

M&L for bell electric heavy duty Ding Dong type 230 volts Single pole complete all as specified and as directed

S&F in electronic fan regulator Step type 120 V 100 watts complete all as specified and directed by Engineer-in-Charge.

S&F of ceiling rose surface bakelite 63 x50mm three terminals complete all as specified and as directed by Engineer-in-Charge.

Supply & fix Single Pole & netural enclosure with a two pin and earth Plug and Socket 240 volt complete with one single Pole MCB of Cap 20 Amps complete all as specified and directed

S&F in replaceent of MCB DB sheet enclosure load line Single pole and neutral 240V with 200 Amp suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated Acrylic double door complete confirming to IP 43 with enclosure blank plates for unused way suitable for 12 way complete all as specified and directed :

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed by Engr-in-Charge. Make- Orient/Crompton/Havells or from the makes specified in list of makes.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 250mm complete as directed.

Supply and fix exhaust fan made of steel body complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 300mm complete as directed.

Supply and fixing LED building light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection and L shape GI pipe bracket of 40 mm dia. complete.

S&F MCBs 240/415 Volts 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB . (DB will be measured and paid separately under respective items of sch A):-

(a) MCB C curve SPN 40 to 63 Amps.

(b) MCB B curve SP 5 to 40 Amps

Supply and fix LED lights fitting 1x 22W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed

Supply and fix LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed .

Supply and fix electric water heater, storage type with glassline MS tank and outer body made out of ABS & PP, heating element of 2 KW storage capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, SS braided connection pipe (02 Nos) of suitable length etc complete all as specified and as directed by Engr-in-Charge. Make:-Racold /Havells/Crompton or from the make specified in list of makes.

M&L for earthing complete with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mtr below ground level) with top edge of earth plate not less than 1.5 Mtrs below ground level connected to GI wire 4 mm Dia as earth lead by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, including PCC (concrete chamber) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate, with fair finish internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge mesh, 80 mm thick RCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including proviSI-on 20 mm dia medium grade pipe and watering pipe shall be 20mm bore medium grade, and including all excavation and earth work & connecting the earthing to an earthing test point complete all as specified & directed .

NOTE: (i) The concrete pit shall be PCC 1:3:6 type C-140 mm thick pre cast cover slab of RCC(1:2:4) type B-1 uSI-ng 20 mm graded stone aggregate reinforced with 8 mm TMT bars @ 10 cm C/C on both SI-des with suitable cast iron handle shall be provided in lieu of cost iron cover shown in the electrical plate No.3 of MES SSR Part -1 (ii) item includes the cost of 7.5 m GI pipe for protection of GI wire. (iii) PCC pits extra cost of addtional length of watering pipe,bends elbows etc.shall be deemed to be included in the quioted rate. (iv) Item includes the cost of 7.5 mtr length Galvised wire 4 mm dia.

Supply and laying galvanised iron pipe, medium grade 20 mm bore with all new fittings bends, elbows, tees, short pieces, connectors, backnuts, diminishing pieces, caps, plugs and unions, etc. of reqd size) trenches including jointing material etc complete all as specified and directed.

S & F Gun metal globe or gate valve (ISI marked), with iron wheel head, screwed both ends, suitable for 20 mm bore iron pipe and fixed including testing complete all as specifed and directed by Engr-in-Charge.

Excavation in trenches not exc. 1.5 m wide and not exceeding 1.5m depth for foundation of poles/laying of cables/stay/strut etc not exceeding 10 Sq m on plan and getting out in soft/loose soil complete all as specifed and directed by Engr-in-Charge.

Returning, filling including spreading, leveling watering and well ramming in layers not exceeding 25 cm complete all as specifed and directed by Engr-in-Charge.

Removing excavated material (soil) n.exc 50m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specifed and directed by Engr-in-Charge.

Cutting existing 50 mm bore GI water supply pipe line in position for insertion for new tee for taping new pipe line with existing complete all as specifed and directed by Engr-in-Charge.

M/S ujjwal associates (BID ID -3302877)

M/S LADPURIA ENTERPRISES (BID ID -3303047)