COMPREHENSIVE REPAIR TO ROOF LEAKAGE, SUKEN FLOOR, ROOFING, FLOORING, CEILING, JOINERY, TOILET, BATHROOM, PLUMBING AND MISC WORK AT U AREA UNDER AGE B/R-I OF GE SUKNA

Amount

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern in roof and wall covering omplete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F Roof truss (framed) trussed, purlins,crane gantires of steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1998 grade St-240 including one shop coat of zink chromate primer paint including preparation of surface including dismantling complete all as specified and directed.

S&F rolled mild steel in plates, gusset plate (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410W (Gde-E-250) quality-A complete all as specified and directed.

S&F Mild steel screw bolts diameter of neck 11 to 15 mm (machine made) with hexoganal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut, exc. 0.5 cm but not exc. 10 cm long complete all as specified and directed.

Taking down chowkats or frame n.exc 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frame but exc. 1.5 Sqm but not exc. 4.0 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutters of any description n.exc 1.0 Sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each complete all as specified and as directed.

Taking down shutters of any description exc 2.0 Sqm each complete all as specified and as directed.

S & F of pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S & F of pressed steel frame of size 165 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in bed plates, filling in pressed steel door frames, hold fast blocks etc, complete all as specified and directed.

S&F 30 mm thick factory made flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side complete all as specified and directed.

S&F 35 mm thick factory made flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side complete all as specified and directed.

S&F factory made wire guazed (panel will be wire guazed in lieu of plain PVC sheet) PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top rails, bottom rails stiles & lock rail. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and single side prelam PVC sheet for top rail, lock rail & bottom rail on either side having one side feathered edge and on other side 10mm 900 bent edge & as gap insert for top rail & bottom rail i.e; panel will be of wire guaze. The wire gauze shall be wrapped on an additional square 8 mm MS Solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly complete all as specified and directed. Note:- Wire cloth / wire mesh shall be measured seperately.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC door shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

M&L powder coated Aluminium anodised door,window,Cup board and ventilator shutter and frame any type (Sliding or openable ) with frame and other similar work, fabricated aluminium mesh etc. aluminium heavy section favricated incl all necessary roller wheels, cleats, handle, locking arrangement and arrangement to fix wire mesh with aluminium channel beading and stainless steel screw incl cost of rubber gasket ,beading roller wheel etc. ,complete all as specified and directed. Note: (a) The weight of rubber gasket beading, roller wheels, etc will not be measured with the weight of aluminium shutters as only aluminium items shall be measure. (b) Wire mesh shall be measured and paid separately. (c) Aluminium hinges shall be included in the unit rate

S&F anodised aluminium powder coated (thickness or powder coating not less than 50 micron) window and ventilator shutters, sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws etc. complete all as specified and directed.

S&F 5.5 mm thick plain sheet glass ordinary quality fixed with aluminium frame work exc 0.50 sqm in each pane complete all as specified and directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned stacks, or stainless steel wire staples complete all as specified and directed.

S & F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned stacks, or stainless steel wire staples complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads area not exc 0.5 Sqm each complete all as specified and directed.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe – 290 Gde E -- 165 complete all as specified and directed.

S&F 75 mm butt hinge, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 100 mm butt hinge, medium weight, cold rolled mild steel complete all as specified and directed.

S&F in repairs 100 mm butt hinge, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 125 mm butt hinge, medium weight, cold rolled mild steel complete all as specified and directed.

S&F in repairs 125 mm butt hinge, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 100 mm extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed.

S&F in repairs 100 mm extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed.

S&F in repairs 150 mm extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed.

S & F 125 mm long Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed.

S & F in repairs 125 mm long Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed.

S & F 200 mm long Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed.

S & F in repairs 200 mm long Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed.

Supply and fix 200 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Supply and fix in repairs 200 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Supply and fix in repairs 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F in repairs magic eye 15mm dia steel body suitable for 35 to 40mm thick doors with all necessary fittings complete all as specified and as directed.

Supply and fix in repairs mortise locks suitable for aluminium door of 100 mm size 4 lever brass body vertical type as per existing or sample complete all as specified and directed.

S & Fin repairs ball catches with 8 mm dia., steel ball, and brass body and striking plates approved pattern pattern fixing to the cupboardm shutters, including letting in and fixed complete all as specified and directed.

M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L PCC 1:5:10 type E-2 (using 40 mm graded crushed stone aggregate) as in sunken portion and including demolition complete all as specified and directed.

M&L Cleaning the surface of suken floor using wire brush, brooming down and washing down with water to remove dust etc. and including brushing with neat cement slurry @ 0.5kg / sqm & one coat with acrylic based polymer modified cementitous composite @ 0.50kg / sqm complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in sunken portion complete all as specified and directed.

M&L for rendering 10 mm thick rendering in CM 1:3 in sunken portion finished even and fair smooth without using extra cement and including taking down complete all as specified and directed. Note:- WPC shall be measured and paid separately.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Roughening surfaces of old concrete floor or concrete surfaces by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and as directed.

M&L 25 mm thick PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) laid above PCC sub floor / correction layer /under layer complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 and including demolition of existing floor tiles complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 and including demolition of existing floor tiles complete all as specified and directed.

M&L coloured glazed ceramic tiles 300x450x7 mm thick as in dado / skirting and vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick screed bed in CM 1:4 including roughening of surface and including demolition of existing floor tiles complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 and including demolition of existing floor tiles complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 and including demolition of existing floor tilescomplete all as specified and directed.

All as per Sl item No. 65 above but in skirting etc. laid over and including screed bed 10 mm thick backing coat in CM 1:3 complete all as specified and directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over 20 mm thick screed bed in CM (1:6) and including necessary dismantling of floor tiles complete all as specified and directed.

M&L machine cut kota stone 20 mm (minimum) thick as in skirting, dado, riser of steps, plinth, etc, laid over and including 20 mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the stone and including rubbing / grinding and polishing and including necessary dismantling of existing floor tiles complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M&L for roof treatment in order of precedence as given below complete all as specified and as directed:- (i) Taking out of existing water proofing treatment and including padding, cleaning the surface using wire brush, brooming down and washing down with water to remove dust etc, and brushing with neat cement slurry @ 3.00 kg of cement per Sqm. (ii) 15 mm thick screed bed in CM 1:4 on surface. (iii) Cleaning of plastered surface and applying one coat of bituminous primer @ 0.40 Ltr / Sqm. (Contd...)

(iv) Supply and laying 3 mm (Minimum) thick APP based polymeric membrane of approved manufacturer with weight not less than 3.60 Kg per Sqm, reinforced with non-woven polyester fabric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 30 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (v) Applying one coat of water proofing paint with aluminium finish over APP as per manufacturer's instruction. Note :- (a) Bituminous primer shall be "ShaliTex Primer" manufactured by M/s STP Ltd or equivalent in M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (b) Laying APP based polymeric membrane shall be done by torch on method as per manufactures instructions. (c) A minimum overlap of 100 mm and 75 mm should be made at the end and sides of the polymeric membrane respectively and all overlaps and joints shall be sealed as per manufacturers instruction. (d) APP based polymeric membrane shall be manufactured by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (e) Water proofing paint shall be by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited

S&F in replacement 4 mm thick non asbestos fibre cement building boards (designer pattern) fixed or laid / inserted to and including aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and including anodised aluminium snap grid frame work for false ceiling hanging from structural steel / scantling with 6 mm GI wire complete all as specified and directed.

S&F in replacement 10 mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling of grid size 605 x 605 mm with and including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n. exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre and necessary hangers 6 mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specifiedand complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

M & L for brick work with sub class ‘B’, old size brick straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces and finished the surface even and fair without using extra cement and including taking down plaster complete all as specified and directed.

M&L for rendering 5 mm thick rendering in CM 1:3 on ceiling finished even and smooth without using extra cement and including taking down complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or stone masonry or on one side of lathing surfaces and finished the surface even and smooth without using extra cement and including taking down plaster complete all as specified and directed. Note:- WPC shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for prepration of new plastered surfaces of wall applying two coats of oil emulsion distemper over a coat of alkali resistant cement primer over a thin layer of wall care putty to obtained smoothness of plastered surfaces complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of alkali resistant primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M & L complete removal of existing treatment of old plastered or previously untreated ceilings surfaces and applying two coats of white wash complete all as specified and directed.

M & L for preparing newly plastered walls surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L preparation of old decorated wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of old decorated steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 500 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank including dismantling of old tank complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank including dismantling of old tank complete all as specified and directed.

S&F in repairs ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed.

S&F in repairs ball valves 25 mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 455 gms) complete all as specified and directed.

S & F in repair 15mm bore stop valve, fancy type,chromium plated, cast copper alloy, concealed type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S & F in repairs Fancy type chromium plated with long shank and cup (Concealed type) 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repairs 15 mm bore fancy type, chromium plated, bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15 mm bore bib tap chromium plated long body fancy type, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F in repair angle stop cock 15 mm bore, chromium plated, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, concealed type, chromium plated long thread with flange complete all as specified and directed.

S&F in repairs pillar taps 15 mm bore,fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F vitreous china european water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F in repairs plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges for european water closet pan complete all as specified and directed.

S&F in repairs vitreous china squatting pan, "Orissa pattern" white, size 580 x 440 mm with integral foot rest, 'P' or 'S' trap and including connection to trap and to flushing pipe, CI anti -syphonage pipe complete all as specified and directed.

S & F in repairs spray jet stainless steel chromium plated for EWC complete all as specified and directed.

S&F in repair PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size not less than 550 x 400 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S & F in repairs 32 mm dia., Waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm and including 32 mm waste pipe & coupling complete all as specified and directed.

S&F in repair stainless steel kitchen rack made out of stainless steel sheet 1mm thick with approx size 900mm x 900mm x 250mm best quality complete all as specified directed.

S&F in repair swivel shower rose size 125 mm of brass chromium plated any colour (minimum weight 40 gms) for fixing with 15mm dia steel pipe complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts, of length 600 mm & suitable for hot water supply complete all as specified and directed.

S&F in repair towel rail 20 mm dia & 600 mm, D-type of brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S & F in repairs 40mm with 250mm long bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed.

S & F in repairs 32mm with 250mm long bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed.

S&F in repairs 15mm bore CP nipple of length 50mm (minimum), suitable for extension of trap in WHB/Sink etc complete all as specified and directed.

S&F in repairs 20mm bore PTMT nipple (Minimum weight 45gms) suitable for HDPE water tank complete all as specified and directed.

S&F 15 mm bore steel water tubing and connections medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor and including dismantling of old pipes complete all as specified and directed.

S&F 20 mm bore steel water tubing and connections medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor and including dismantling of old pipes complete all as specified and directed.

S&F in repairs decorative curtain rod of wooden finish powder coated of 25 mm dia including 06 nos. curtain ring per running metre complete all as specified and directed.

S&F in repairs decorative type wooden finish double brackets support for holding curtain rods and corner to be fixed to ends of curtain rod fixing with screws complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

S & F in repairs of 125 / 110 mm size PVC (SWR) gully trap, setting and jointing with solvent cement including top cover grating complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls and including taking down of old materials complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls and including taking down of old materials complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F in repairs PVC (SWR) 75 mm bore bend with access door, of any radius complete all as specified and directed.

S&F in repairs PVC (SWR) 110 mm bore bend with access door, of any radius complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) junction single, (single T) equal or unequal, fixed with cement solvent, with oval access door complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) junction single, (single T) equal or unequal, fixed with cement solvent, with oval access door complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) junction double, (double T) equal or unequal, fixed with cement solvent, with oval access door complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) junction double, (double T) equal or unequal, fixed with cement solvent, with oval access door complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S & F in repair for Soap dish,Vitreous China, white, approxmate size 160x160x90mm, foxed to plug with chromium plated brass screws complete all as specified and directed.

M/S B B CONSTRUCTION

SHRI N.DAS

VICKY ENTERPRISES

KARMIBRINDA

M/s TRIMURTI ASSOCIATE

S D CONSTRUCTION CO

SHANTI UDYOG

MS UNITY CONSTRUCTION CO