Construction of SCADA Control Room and Informatics Centre at Rest House Campus Sri Ganganagar

Amount

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.

Provinding and laying in position cement concrete including curing , compaction etc. complete in specified grade excluding the cost of centering and shuttering - all work up to plinth level M-10 grade nominal mix 1:3:6(1cement :3coarse sand :6 graded stone aggregate 20mm nominal size .

Brick work with common burnt clay F.P.S. (Non modular) bricks of class designation 75 in foundation and plinth level in : Cement mortar 1:6 ( 1 Cement : 6 coarse)

Brick work with common burnt clay F.P.S. (Non modular) bricks of class designation 75 in superstrtucture above plinth level upto floor level in all shapes and size in : Cement mortar 1:4( 1 Cement : 4 coarse)

Centring and shuttering with plywood or steel sheets including strutting propping bracing both ways and removal of formwork for foundation ,footings,strap beam , raft ,bases of columns . PWD BSR-2019, B-4 item no. 4.9

Providing and fabricating reinforcement for R.C.C. Work including straighteninng , cutting,bending,placing in position and binding (including cost of binding wire) all complete up to floor five level, Theremo mechanically treated bars (conforming of relevent IS code)

Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish :12mm thick .

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: New work (two or more coats) over and including priming coat with cement primer.

Finishing walls with water proofing cement paint of required shade including all scaffolding. : New work (Two or more coats applied @ 3.84 kg/10 sqm).

P & F 1st quality Vitrified tiles on floor, skirting and steps etc. in different sizes ( thickness to be specified by manufactuer ) with water absorption less than 0.08 % and confirming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1 : 4 including grouting the joints with white cement and matching pigment etc complete. size 600 mm x 600 mm.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. size 600 mm X 600 mm.

Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.Black/South 1501 Cm2 to 3600 Cm2 Tiles .

Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4).

Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). up to 300*450mm size

Providing and fixing pressed steel door frames confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4(M15 grade) complete as directed by Engineer-in-charge : profile B.

Providing and fixing external grade board solid core single/ Double leaf flush door shutters IS: 2202(Part-II)1996 marked using Phenol formal dehyderesin in glue both sides with approved stainless steel fittings complete as per annexure 'A' 35 mm thick commercial venner both side

Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred welded and grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm long embedded in C C block 15 x 10 x 10 Cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to frame for paitam fixing float glass 4mm thick panes with glazing clips and metal sash putty and fixing of shutters frames peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in –charge Window openable.

Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size.Welded mesh 50 mmx 25 mm x 2.1 mm.

Providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS 2095- Part I at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting.

Providing and fixing 14 mm thick Acoustical with fine fissured tiles/ Mineral fibre high density tiles with butt edges false ceiling tiles of size 595x595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanized @ 170 gsm/sqm.) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross “T” of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised level clips spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-Charge. (The tiles should of 90 % RH avg. NCR 0.55 light reflectance> 80% thermal conductiveity K = 0.052-0.057 w/m K colour white. Fire performance class 0/class I(BS 476) with warranty against sag)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall).

15mm nominal outer dia pipes

25mm nominal outer dia pipes

P & F European type white glazed vitreous china 1st quality Double syphonic W.C (IS :2556 Mark) with P or S trap including cutting and making good the wall and floor

P & F Automatic Flushing Cistern of first quality (IS : 774 mark) of approved make fitting, syphon with copper tube, C.I. brackets complete including cutting and making good the wall. WVC Automatic flushing cistern - 10 Litre Capacity

P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. WVC Flat Back half stall Urinal size 580x380x350 mm/ Angle back 450x375x350 type liped front..

P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, PVC waste pipe with PVC nut 32mm complete including cutting & making good the wall :Vitreous china flat back wash basin 630x450 mm

P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:C. P. Brass swan - neck, 15mm nominal bore.

P & F PVC Storage Tank (IS:12701 marked indicating the BIS license No.) of approved make with cover, 25 mm dia 1 M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including placing on terrace (at all floors), making connection etc. complete of approved design.1000 Litre capacity.

P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15 mm Brass (IS:8931 marked).

construction of septic tank in all types of soil with 40 cm thick brick masonary in CM 1:6,15CM thick C.C. bed of 1:5:10 ,M-15 Grade CC flooring & over stone slab covering , 80 mm thick slab ,joiting of slab in CM 1:3 ralthal ,kharanja , 50mm thick stone partition walls, 20mm thick plaster in CM1:6 finished with neat floating cement ,4 nos CI foot rests of approved design , two no 450 mm dia each cement concrete cover with frame , earth work etc. complete as per appoved drawing including disposal of surplus earth within a lead of 50 mtr : size 200*100*130cm(for 10users)

Construction of Soakage well in all types of soil of approved drawing, top 1.5 Mtr. depth in 345 mm thick brick masonary with CM 1:6, 80mm thick stone slab covering resting on stone lintel of cross section 150 x 300mm (two numbers resting on stone bed plate), jointing of slab in CM 1 : 3, Ralthal, Kharanja 40 mm thick M-15 grade C.C. flooring, out side plaster in CM 1 : 6 upto 450 mm depth, earth work etc complete including disposal of surplus earth within a lead of 50 Mtr. including providing and fixing of PVC Vent pipe 75mm dia upto 1.50 Mtr. height as per direction of Engineer in Charge including making connection etc. 3 Mtr. outer dia in top 1.50 M depth and 90 Cm dia at bottom. Depth of soakage well 10 to 12 Mtr. from ground level. [As per Bikaner Practice].

P & F Towel Rail or Ring of approved quality/make: 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.Size 600 x 450mm x 4 mm thick .

P & F Soap Dish or Tray of approved quality/make WVC (1st Quality, ISI Marked) recessed size 150 x 150 mm.

making of hole in wall of required size for housing exhaust fan and same with cement plaster as required of following size more than 457mm &upto 610.

P & F of ventilating fans, capacitor start, single phase with impeller, ABS body, automatic openable louver shutter in existing opening including making connection, testing etc. as required.150 mm Sweep.

P & F of IP20 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Downlight with die-cast aluminum housing & Heat Sink for heat dissipation, high purity reflector with external driver having efficiency > 85% and in compliance to IEC standards. Power Consumption of ≤ 7W/ 10W / 15W / 18W with ~ 500 / 750 / 1100 / 1250 lumens, System Lumen efficacy of 70 lm / watt output suitable to replace 1x18W / 2x18W / 2x 26W CFL Downlights, life time of 50000 Burning Hours with 70% of intial Lumen maintaned. CCT 3000°K , 4000°K & 6000°K. Fixture shall be CE compliance.Recessed Mounting LED Downlight 9/10W.

P&F of decorative round/square shape surface mounting ceiling fitting complete with horder ,aluminium anodized back plate glass globe of appoved desing,prewired terminal block making connection ,testing etc .as required as approved by engineer in charge. 150mm.

P&F Star rated double ball bearing capacitor start , aluminium body &blade ceiling fan with down rod up to 30 cm with 3*1.5 sqm pvc insulated flexible copper conductor making connectin testing etc as required 1200mm sweeo 5 star rated.

P&F of IP 20 led tube light 20 watt with external batten made from CRCA sheet steel suitable to replace T-8/T-12 tube light integral driver 2000 luman with 5% tolerance system luman efficiency of 100 Lm / watt minimum expected life time of 25000 burning houres , CCT 5700 K, ANSI ,CRI 80 , driver efficincy > 85% , life expectancy of driver min 30000 hrs PF 0.95 at full load / 230volt AC.

Wiring of twin control light point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) of approved make on surface ISI marked ( IS:14927 P - II ) PVC casing capping & it's accessories, round tles, moulded PVC Modular box with earth terminal, 6 A two way Modular switch, Modular plate with grid plate, screws, making connections, testing etc. as required. short point(up to 3 m).

P&F 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C/ D tripping characteristic) ISI marked IS 8828(1996)]/ conforming to IEC 60898 in existing board/sheets including making connections, testing etc. as required.Single pole MCB 6 A to 32 A rating.

P&F 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C/ D tripping characteristic) ISI marked IS 8828(1996)]/ conforming to IEC 60898 in existing board/sheets including making connections, testing etc. as required. Double pole MCB 6 A to 32 A rating

SITC of Air Cooled split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (EP foam pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 4 Mtr (IDU to ODU), R-22/R-410 Refrigerant, Remote, suitable for 400/230V +10% of 50 Hz ,1 /3 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / reciprocating / rotary compressor as specified.1.5 TR with 5 star rating of BEE

Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) of approved make on surface ISI marked ( IS:14927 P - II ) PVC casing capping & it's accessories, round tiles, Moulded PVC Modular Box with , 6 A Modular switch,Modular plate with grid plate, screws, making connections, testing etc. as required.

short point(up to 3 m) E010501

medium point( up to 6 m)E010502

long point( up to 10 m)E010503

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.)With float glass panes of 5 mm thickness

SITC of self contained drinking water cooler with energy efficient hermetic sealed type compressor ,non CFC refrigerant suitable for operation 0n 230V/1pH/50Hz as supply, fullnstainless steel{S304}Body and tank ,stainless steel water tray , minimum two nos faucets and suitable drainage system complete in all respect with 300mm height ms fabricated and painted plateform .complete in all respect of the following capacity. cooling capacity 80ltr/Hr and storage capacity120ltr.

SITC of reverse osmosis water purification system (RO system) compatible for water cooler with ABS construction fully automatic operation with auto start and auto off capacity ,equipped with standard filtration stage/ cartridge (sediment filter, activated carbon filter .UF ,sediment,filing composite RO mebrane),input power supply 100-250V AC 1 PH. system voltage 24vDC, percentage reduction in TDS 90% or better .the job includes installation at site with existing water supply line with requterly service(and also as & when required) of above RO system during warranty period including requied consumable items. Production capacity -15LPH , WATER Storage capacity 8ltr

supply installation testing and commisioning of1.8 KVA pure sinewave home UPS/ INVERTER WITH 2 numbers 150AH tubuler battery for backup. With following specification:- specification rating 1.8KVA technology- DSP Pure sinewave technology -DSP pure sinewaval/ PV - 120-280VAC(inverter mode).180V-250VAC(UPS mode) O/P voltage -220VACVoltage regulation :-+/-5%(on batt. mode) technology -DSP Pure sinewavel/P V- 120-280VAC(inverter mode ),180V-250VAC(UPS MODE)O/P voltage regulation :-+/-5%(on batt. mode)O/P frequency :-50Hz+/-Hz(battry mode) over load capacity:-110% for 5min. on mains mode efficiency:- better than 92% charging current :-7A/10A/12A/15A/20A/25A (programmble) D.C. voltage :-24AH capacity:-3600VAH indicatioms:- mains on,inverter on,O/L, low battery,battery charging protections :-rev phase,S Ckt, over temp. O/L, battery loose relative humidity :-95%RH Non-condensing operating temprature :-0-50 deg.c safety standard:-IEC/EN60950EMC Std:-IEC-EN62040-1, EN62040-2,EN62040-3,EN61000-4,EN60146 Certificates:-ISO 9001,ISO 14001,ISO18001,ROHS &CE

Providing and fixing 1.0mm thick Stainless Steel AISI 304 (18/8) kitchen sink & IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required :Stainlees steel kitchen sink - with drain board 510 x 1040mm bowl depth 200 mm.

P & F of capacitor start, metal body, metal blade three speed wall mounting fan of following sweep with the help of anchor bolts including making connection testing etc. as required.400 mm sweep(Oscillating type)

P & F of IP20 LED ceiling / recessed / suspended mounting light fixture made from CRCA sheet steel housing, high purity / transmisivity diffuser for uniform light distribution. High efficiency driver electronics having efficiency > 85% and in compliance to IEC standards (Integral with light fixture). Power Consumption of 40W / 50W / 60W ~ 3000/3300/4200 lumens, System lumen efficacy of 70 - 80 lm/Watt output suitable for 2x36WFTL / 2x36W CFL / 3x36W CFL light fixtures, life time of 50,000 burning hours with 70% initial lumens maintained. CCT 3000°K, 4000°K & 6000°K. Fixtures shall be CE compliance.36W LED light fixture 2'x2' with acrylic / prismatic front cover.

Wiring of 3 pin 5 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) of approved make in surface / recessed ISI marked medium duty PVC conduit & it's accessories, Hot Dipped Galvanized M.S Modular box of 20 SWG with earth terminal, 6 A modular switch, 6 A modular socket, Modular plate with grid plate, screws, making connections, testing etc. as required.On board.

UPVC SOIL WASTE & RAIN WATER (SWR ) PIPES Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single socketed pipes.Type A 110 mm diameter .

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single Bend with Door 87.5°. 110mm dia .

Supplying and fixing of power plug point Modular accessories on hot dipped galvanized modular on surface or in recessed with suitable size of grid plate with cover plate including cost of modular 16 amp. Switch and socket outlet , making connection , testing , etc. as required.

Providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm x 6.0mm and opening of size 102mm x 99mm to aluminum window/vent with required screws, Y and H aluminium sec (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge.Anodised aluminum (anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on New Work

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required.2 x 2.5 sq.mm

Providing and laying factory made chamfered edge Plastic coated Designer Cement Concrete paver blocks of required strength, thickness and size/shape, made by table vibratory method, to attain superior smooth finish using PU or equivalent moulds, laid in required Grey/ Yellow/ Red or any other colour and pattern over 50 mm thick compacted bed of Coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per manufacturer's specifications and direction of Engineer-in-charge.80 mm thick C.C. Interlocking Paver block of M-30 grade with approved color design and pattern.

Earthwork in foundations trenches,lift upto 1.5 m.stacking the excavated soil clear from the edge of excavation and then returning the excavated soil in 15 cm. layers when required into sides of foundations etc.,consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 30m.In ordinary soil like sandy loam,soft clay etc.

Carriage of Bats Ballast ,Kankar,Sand, Bajri, Stone, Grit,Murram,Soiling Stonesfor Road,Water,Good Eatrh.lead upto 10Kms.

supply installation testing and commisioning of IP-65/ROSH/CE Compliant itegrated solar street light fixture having die cast aluminium body incases with intergrated monocrystalin solar PV Panal with lithium (LIFEPO4) ferro fasfate battery and compalint to MNRE Specification BIS approved . luminaire should be with secondary optic lenses for better distribution with delivered affincancy of >100 luminus per watt ,with minimum 40000hrs . rated lamp life with LED brand of philips ,osram ,nichia,cree,seoul and driver afficance should be >85%,CRI >75,CCT6000 TO 6500 K ,MICRO contral , high afficance control cum driver designed with autmatic dimming function with PIR motion sensor (full power lighting whan a humen move in the sancer range and only 30% lighting whan a human move out ) dusk to dowen operation ,working tamp. (-)10 C(+) 55C, WITH adjustable clamp suitable for pole ,wall mounting complete in all respect with protction like short circot over lode reversed polareverse polarity and battery protections . light coverage must be 120Degree or grater complete as required compact solar LED street light -25 WP (mo) 18 V/12.8V 9AH /12W

Table Type 5 (Seating Capacity-8 seater, Width in mm-1200, Length in mm-2400, Shape of table top-Rectangular, Height in mm-750 mm) (inclusive all taxes)

Chair Type 4 (Chair Type-with Arms, Frame Type-4 Legs, Castors-without) (inclusive all taxes)

Table Type 3 (Storage provided one side, Depth of table-600 mm, Length of table top-1200mm) (inclusive all taxes)

Laying of lawns including ploughing levelling breaking of clods manuring & removal of stones etc. (Cost of manure of extra good earth to be paid seperatley) Maintenance of lawns for 30 days of more till the grass forms a thick lawns free from weeds & fit for mowing in the duration of planting if lawn die some where the contractor will replant it at his own cost.In rows 5 Cms. apart in either direction .

Supply of different H.P. Motor pumps submersible pumps/ multistaged pumps at store including transportation etc. complete:Motor pumps 7.5 H.P. ISI marked.

Supply of different sized pots at site store including loading unloading & transporation etc.Cement pot 350 mm size .