PROVN OF TWO SINGLE JCOS ACCN BATHROOM AND ADDN / ALTERATION OF BLDG NO E-60 AND GENERAL STORE ROOM FOR RAM AUDITORIUM UNDER AGE B/R-IV OF GE (SOUTH )MEERUT CANTT

Amount

Surface excavation in soft/loose soil n exc 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m depth in soft/ loose soil for foundation area n.exc 10 Sqm on plan, getting out and levelling of bottom surface to required level complete all as specified and directed.

Removing excavated materials to a distance not exc 50 m and deposited where directed at a level not exc 1.5 m above the starting point all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n.exc. 25cm thick in soft / loose soil complete all as specified and directed.

Material & labour for pre construction antitermite treatment by treating the top surfaces of filled earth at the rate of 7.5 ltrs of emulsion per Sqm of surface area complete all as specified & directed.

Material & labour for pre construction antitermite treatment by treating the backfill in contact with foundation with anti termite (ATT) liquid at the rate of 7.5 litres of ATT emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified & directed.

Material & labour for pre construction antitermite treatment by treating the soil under plinth protection at the rate of 5 ltrs of emulsion per sqm of surface area complete all as specified & directed.

Material & labour approved soil filling under the floor, spreading and leveling in layers n. exc. 25cm thick well ramming including watering as required complete all as specified and directed. ( Note:- Soil obtained from exc item of BOQ herein before shall be used )

Material and labour for hardcore of broken bricks of gauge not exc 63mm, deposited, spread and levelled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

Material and Labour for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in foundation fillings and mass concrete complete all as specified and directed.

Material and labour for use and waste formwork to sides of cocrete foundation, footings, bases of column, rafts, plinth beams and similar work vertical or to batter for rough finished flat surface of concrete , complete all as specified and directed.

Material and labour for for use and waste formwork to sides of pillars, posts, struts, piers, columns and stanchions to give rough finished flat surface of concrete complete all as specified and directed.

Material and labour for form work to sides and soffits of beams lintels etc finished rough complete all as specified and directed.

Material and labour for providing formwork to soffits of suspended slabs such as roof slab , floor slabs , landing ; chajjas and similar work not exc 200mm thick; rough finished surfaces of concrete flat complete all as specified and directed.

Material and labour for from work to the edge of concrete flat n.exc 200 mm thick , rough finished surfaces of concrete flat complete all as specified and directed.

Material and labour for mild steel TMT bars 8mm dia and over, cut to length, bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia , quality conforming to Fe- 415, Fe 500 or Fe-550 as in steel reinforcement for concrete complete all as specified and directed.

All as per Srl item No 16 here-in-before but 6mm to 8mm dia as in stirrups/rings complete all as specified and directed.

Material and labour for providing reinforced cement concrete , M-25 design mix (using 20 mm graded crushed stone aggregates) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

Material and labour for providing reinforced cement concrete M-25 design mix (using 20 mm graded crushed stone aggregates) in columns, pillars, piers, posts and struts complete all as specified and directed.

Material and labour for providing reinforced cement concrete M-25 design mix (using 20 mm graded crushed stone aggregates) in beams, cantilevers, bressummers complete all as specified and directed.

Material and labour for providing reinforced cement concrete M-25 Design Mix , 1:2:4 (using 20 mm graded crushed stone aggregates) in roof slabs supported on walls, beams and the like as in beames, lintels over 1.5 m span etc. complete all as specified and directed.

Material and labour for brick work with fly ash bricks straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and directed.

Material & labour for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.

Material & labour for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or stone masonry surfaces, finished even and smooth without using extra cement complete all as specified & directed.

Material and labour for rendering 5 mm thick in cement mortar 1:3 on ceiling of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base floor, finished even and rough to receive floor topping all as specified and directed.

Material and labour for non skid ceramic tiles 8-10 mm thick (square / rectangular) of size 600mm x 600mm set and jointed with neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and and directed

Material and labour for coloured non skid ceramic tiles 7 to 8 mm thick, (square / rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and and directed

Material and labour for cloured Glazed ceramic tiles in vertical surfaces 350x250x7mm / 450x300x7-8mm thick set and jointed in neat cement slurry and pointed in white or cloured cement to match over and including 10mm thick rendering in CM (1:4) on fair faces of brick or concrete surface complete all as specified and directed.

Material and labour for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) in path /plinth protection, finish cement concrete surface even & smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of newly plaster surface of wall and applying two coats of cement base paint over and including one coat of primer complete all as specified and directed.

Material and labour for preparation of newly plastered surface of wall etc and applying two coats of oil bound distemper including one coat of primer over and including 1mm thick wall putty to prepare smooth surfaces complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of ceiling and applying three coats of white washing complete all as specified and direcrted.

Material and labour for roof padding in PCC 1:2:4 type B0 (using 12.5mm graded crushed stone agg) laid to a minimum consolidated thickness 50mm to provide a finished slope 1:30 complete all as specified and directed.

Material & labour for cleaning of concrete surfaces and applying priming coat using with bituminous primer @ 0.30kg per Sqm followed by evenly a tack coat @ 1.20 kg per Sqm using with 85/25 grade industrial bitumen, over it laid with APP modified polymeric water proofing membrane with non-woven polyester reinforced of weight not less than 3.60 kg per Sqm unrolled & bonded to substrate with side and end laps 75mm & 100mm as per manufacturer’s instruction and applying over it a tack coat using with 85/25 grade industrial bitumen @ 1.20 kg per Sqm and finally finished the top of polymeric water proofing membrane with a coat of bituminous aluminum paint @ 0.200 kg per Sqm as per manufacturer’s instructions complete all as specified and directed.

Supply and fix 30 mm thick flush shutters, solid core construction, with particle board core and plywood facepanels, commercial type on both sides, complete all as specified and directed.

Material and labour for gauzed shutter made out from angle iron 35x35x5mm, 25x25x5mm and 1.5 mm thick as shown on drawing, the frame for shutter shall be of pressed steel and 10 mm square bars grill complete with fly proof wire mesh having 0.63mm nominal dia wire and 1.4 mm average width of aperture including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply and fix pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates, etc profile of frame 125x60mm made out of 1.25 MS sheet including one shop coat of primer complete all as specified and directed.

Supply and fix mild steel angle iron door frame 40mm x 40mm x 6mm conforming to Fe-410-0 incl 12mm dia deformed bars for strengthening at bottom of chowkhats complete all as specified and directed.

Supply & fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC, ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, supplying & fixing in the frame at site as per specification & drawing for Item No. 08080 on page No 174 of SSR 2020 (Part-II) complete all as specified and directed.

Supply & fix 125mm size aluminium alloy handles, cast type, anodised complete all as specified and directed.

Supply & fix 150mm long aluminium anodized tower bolts of extruded section complete all as specified and directed.

Supply and fix 250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Supply and fix MS 150mm size helical door spring including roller and plate fixed with screws to wooden or welded to iron chowkat complete all as specified and directed.

Material and labour for preparation of new or previously untreated wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour for preparation of new or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer all as specified and directed.

Supply and fixing PVC waste pipes of 40/32mm bore suitable for wash hand basins/sinks complete all as specified & directed.

Supply and fix 100/125mm dia CP grating complete all as specified and directed.

Supply & fix for 110 mm bore PVC floor traps plain with grating and 300 mm long out let inlcuding jointing with cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) complete all as specified and directed.

Supply and fix 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

Supply & fix steel window box type using ERW 'P' section comprising double frame for gauged and glazed skeleton shutter jointed internally with flat iron 40x3mm all arround the complete frame including iron mongry etc complete including hinges, handle tower bolts stops, lugs etc all as shown on drawing Note (i) For the purpose of measurement & payment double shutter with frame shall be considered as one unit .

Supply & fix steel window or ventilators fixed type wire guage and top hung glazed shutters with glazing bars complete all as specified and directed.

Supply and fix mild steel work as in hold fast etc and similar articles confirming Fe-310-0 with & including material & labour for tarring & sanding complete all as specified & directed.

Supply & fixing mild steel framed work such as grills or framed guard bars with end of bars shouldered or reveted or forged into spike, and similar articles conforming to Fe 410-0 or Fe 310-0 complete all as specified & directed.

Supply & fix 15 mm bore gun metal globe or gate valves with Iron wheel head screwed both ends for iron pipe complete all as specified & directed.

Supply and fix bib taps, cast copper alloy chromium plated ,long body with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore and fixed complete all as specified and directed.

Supply and fix vitreous china wash hand basin, white, flat back of size 550x400 mm excluding taps, waste chain and plug and porcelain stopper but including brackets and CP brass waste coupling complete all as specified and directed.

Supply and fix angular valve , 15mm dia, cast copper alloy, chromium plated fancy type with long shank and cup screwd down, high pressure ,screwed both ends for iron pipes or for unions all as specified and directed.

Supply and fix rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) 500 litre capacity hoisted and fixed in position complete all as specified and directed.

Supply and fix PVC low level duel flushing cistern 9-10 Ltr capacity white with inlet, ball valve, float , handle ,brackets and 32 mm dia PVC flush pipe for low level cistern complete all as specified and directed.

Supply, fixing or laying of 15mm bore, GI tubes medium grade, galvanised, with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

Supply, fixing or laying of 20mm bore, GI tubes medium grade, galvanised with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

Supply and fix 3 mm thick plain sheet glass ordinary quality and glazing with oil putty / beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

Supply and fix 3 mm thick sheet glass frosted type ordinary quality and glazing with oil putty / beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

Supply and fix galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples including necessary beadings complete all as specified and directed.

Supply and fix butt hinges 100mm size, medium weight, cold rolled incl necessary screws complete all as specified and directed.

Supply and fix butt hinges 100mm size, stainless steel heavy quality incl necessary screws complete all as specified and directed.

Supply and fixing PVC connections of 450mm long suitable for 15mm dia iron pipe incl PTMT nuts complete alll as specified & directed.

Supply and fix 20 mm bore, PVC ball valves, high pressure with polyethylene float and fly nut, including epoxy coated aluminium rod, screwed for iron pipe or for brass ferrule complete all as specified and directed. ( Min Wt:- 210 Gms).

Supply & fix vitreous china squatting pan ‘Orrisa pattern’ size 580 x 440 mm white with integral foot rest,Cast iron ‘P’ or ‘S’ trap, lime concrete bedding complete all as specified and directed.

Supply and fix 15mm bore pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe fixed complete all as specified and directed.

Supply and fix 110mm PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches/ laid under floorcomplete all as specified and directed

Supply and fix 75mm PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches / laid under floor complete all as specified and directed

Supply & fix PVC (SWR), junction single, (double T) equal or unequal 110mm bore complete all as specified and directed.

Supply & fix tubular towel rail of 20mm dia of brass, chromium plate, ’D’ type, 600 mm long between flanges complete all as specified & directed.

Supply & fix 0.63 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified & directed.

Material and labour for chequered cement concrete tiles 300mmx300mmx20mm thick with grey cement and no pigments , set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment laid over including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Material & labour for plain cement concrete bed to drain pipes including packing under, haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) for 150 mm bore pipe complete all as specified and directed.

Material & labour for 150 mm bore salt glazed stoneware drain pipes laid in trenches and jointed in cement mortar (1:1) using hemp yarn socked in thick cement slurry all as specified and directed.

Material & labour for 10 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.

Material & labour for PCC (1:3:6) type C1 using 20 mm crushed stone aggregate as in benching to man hole surfaces finished even and smooth complete all as specified and directed.

Material & labour for construction of Septic tank 25 users capacity, exc in ordinary soil, foundation conc in PCC 1:2:4, brick work in CM 1:4 , RCC slab and covers in RCC M-25 design Mix 1:2:4 including RCC precast manhole cover having 6 mm plate embedded all around /fibre reinforced cover with angle iron frame , CI Vent pipe complete all as shown in TD Drg ( TD/217 sheet 1/7 to 7/7 of HQ CEBZ ) complete all as specified and directed.

Material & labour for construction of Soakage wells, excavated. in ordinary soil, foundation PCC 1:3:6 walls of honey combed and solid brick in cement mortar, RCC slab in M25 design mix, filling work with brick bats, complete of size 1.80 m dia x 3.00m effective depth complete all as shown in TD Drg ( TD/309 sheet 1/4 to 4/4 of HQ CEBZ ) complete all as specified and directed.

Supply only Integral water proofing compound complete all as specified and directed.

Material and labour for anodised aluminium partition, aluminium sections weighing 0.55 Kg/m(min) incuding necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, handles, incluidng anodised aluminium frame with one or more rebates including supply and fix 5 to 6mm thick black glass and all as specified and directed.

Supply and fix vitreous china urinal, half stall type white, with grating, union for discharge pipe, flush pipe and waste pipe, CP urinal spreader fixed to water supply pipe etc complete all as specified & directed by Engineer-in-Charge.

Material and labour for 60 mm thick coloured rubber moulded (comparising of red & yelow colour in 50:50 ratio) machine pressed interlocking pavers in approved shape and size confirming to IS 15658-2006, M-35 Grade set and laid over and including 25mm thick coarse sand complete all as specified and directed.

Material and labour for built in steel cup board with pressed steel frame of size 75x45x1.25mm fixed to masonary wall in PCC 1:2:4 type B-1 (using 20mm graded cushed stone aggregate) block of size 230x230x150mm by Mild Steel FI 25x3mm hold fast 150mm long , 1.00 mm thick pressed steel shutter godrej pattern including MS hanging rod of 10 mm dia with bracket fixed on inner side of shutter , on other leaf provision of MS peg set of three pegs including locking arrngement ( MS lock 100 mm size 4 lever with key ), spray painting two coat over red oxide primer with spray gun all around the steel surfaces of frames and shutter complete all as specified and directed by Engr-in-Charge.

Material and labour for precast cement concrete solid block masonry 1:2:4 type B-1 using 20 mm graded crushed stone aggregate exc 10 cm in width and set in CM 1:6 omplete all as specified and directed

Material and labour for point wiring with 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, stranded, FRLS PVC insulated, unsheathed, copper conductor cable in and including PVC concealed conduit of any size/dia complete with all accessories/fittings, brass screws, washer etc, sunk zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and earth dolly for One tube light/Bulb/Bell/ street light point controlled by one, one way switch 05/06 Amps complete all as specified and directed.

All as per serial item No 91.00 here -in- before but for one ceilling fan/exhaust point controlled by one, one way switch 05 / 06 Amps.

All as per serial item No 91.00 here -in- before but for One 3 pin, 05 / 06 Amps socket outlet point on independent board controlled by one, one way 05 / 06 Amps switch.

All as per serial item No 91.00 here -in- before but for One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch.

All as per serial item No 91.00 here -in- before but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15/16 Amps socket outlet point on independent board.

Supply and fix switch piano flush type, 05/06 Amp single pole, one way 240 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fix socket outlet 3 pin, 05/06 Amp 240 volts complete all as specified and directed .

Supply & fixing switch piano, flush type, 15 / 16 Amps, single pole, one way, 240 volts complete all as specified & directed.

Supply & fixing socket outlet 3 pin, 05 / 06 Amps,3 pin 15 / 16 Amps (2 in1 multipurpose) flush type, 240 volts complete all as specified & directed.

Supply and fixing steped type electronic fan regulator flush type on the existing sheet etc. AC, 230 volts with and including connector complete all as specified & directed by Engineer-in-Charge

Supply and fixing LED bulk head 10 W with clear prismatic diffuser, including all acessories for fixing on wall all as specified and directed.

Supply and fix decorative LED tube light fitting 1x20 Watt, with opal diffuser, environment friendly, energy efficient MS batten with retrofit T8 polycarbonate tube-01 No, complete with all accessories and fixing material complete all as specified and directed.

Supply and fix lamp holder (Angular/Straight), insulated body, with back plate for batten fitting all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lamp 9 watt.

Supply & fixing of ceiling rose 3 terminal PVC / poly carbonate, isolated body complete all as specified & directed.

Supply and fix MCB DB double door DB 200 Amps rated copper bus bar, pan assembly etc with interlocking links, blanking plates cable ties identification labels SPN 12 way, incomer and SP MCB as out going complete all as specified and directed.

Supply and fix Isolator DP pole 63 Amps 16 KA , 415 volt 50 Hz complete all as specified and directed.

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed. (Note- After completion of work if desired result of earthing is not obtained the earthing shall be redone without any extra cost to Govt.)

Material and labour for sheet metal enclosure for DB's with IP 43 protection 200 Amp rated insulated bus bar, shrouded neutral bar, earth bar, blanking plate, cable ties & circuit identification labels 240 volts SPN 8 way concealed in wall including all cutting holes in or through walls, making good to walls, ceiling etc including two coats of white/coloure washing/distempering etc to the disturbed surfaces to match the existing complete all as specified and directed.

Supplying, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 16 Sqmm 2 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc complete all as specified and directed.

Supply/laying and fixing 40 mm bore galvanised steel tubes with all fittings, light grade, laid in trenches for cable protection complete all as specified and directed.

Material and labour for washed river dry sand cushioning in trenches 80mm thick before laying the cable and 150mm thick after laying the cable including spreading levelling and hard punning complete all as specified and directed.

Supply and installed LED security light fitting 1x45 Watt luminaries with pressure die cast aluminium housing comprising high power LEDs enclosed with lens embedded PC cover with LED driver complete IP 65 protection. : Make:- Havells Model-Endura Platinum cilylite, or equivalent in Bajaj / Phillips/Crompton

Supply and fixing ceiling fans 1200 mm sweep complete with accessories 230V Single Phase star rating 50 Watt all as specified and directed.

Material and labour for contineous brick edging with width equal to the length of the brick of whole sub class 'B' bricks laid on edge for protection of cable complete all as specified and directed.

Supply and fixing LED tube light fitting 1x9/10 watt surface mounted, with extruded polycarbonate, integrated lamp & dirver with opal diffuser and decorative end plates complete with all acessories all as specified and directed.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 4 way with 200 Amps rated copper bus bar and IP-43 & IK 09 protection with metal double door and flush to wall including all cutting etc on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and directed.

Supply and fixing MCB SP, AC 240 volts of 06 to 32 Amps capacity “B” curve and making connections complete all as specified & directed.

Supply and fixing MCB SPN, AC 240 volts of 06 to 40 Amps capacity “B” curve and making connections complete all as specified & directed.

Supply and fix , security light brackets 32 mm dia GI pipe medium grade upto 0.60 mtr long bend to shape at 100-120 degree including flat iron clamps and suitable nuts and bolts grouted in wall including all material required for fitting, including matching the surface with existing all as specified and directed .

Material and labour for sub main wiring with 4.00 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor FRLS cable with and including continuous earth wire of size 4.00 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dolly including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as specified & directed. Note : One meter of conduit along with 2x4.00 sqmm wire and one 4.00 sqmm earth shall be measured as one unit length )

Arun Construction Co.

AR Enterprises

SHAKTI CONSTRUCTION CO

Jay Ambay Enterprises

SA construction co.

CHANDRA ENGINEERS