Loading
Loading…
Loading…
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹97.6 L
EMD Value
₹2.0 L
Closing Date
12 Nov 2026, 3:00 pm
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
NORTH
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N OR 'V' Whichever is less; where. V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per ANNEXURE-XXXIII, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work :- Trenching cable laying location and /OR signal foundation/ erection/ termination/wiring in connection with any signalling work
7 conditions
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tender document, Scope of work & GCC 2022 are attached with the tender.
Repair and maintenance of outdoor signaling gears such as Signals, Location boxes, Point machines, Track circuit connections, AFTC outdoor connections in Kalyan section under SSE/Sig/KYN of Mumbai Division.
CR-BB-SNT-NORTH-2026-97~CR
CR-BB-SNT-NORTH-2026-97
Open
Works - General
12 Months
Mumbai, Maharashtra
₹0
₹2.0 L
15 Oct 2026
15 Oct 2026
29 Oct 2026
31 items across 1 schedule · ₹37,14,096.55 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Replacement of old signal unit /signal route of main signal . this would include releasing of old unit from top of signal post erection and mounting of new signal unit over the post .This aiso includes bringing new signal unit from station to site and bring back old unit from site to station. (Inspection Agency Consignee) | Numbers | — | — | 13,988.7 |
| 2 | Refixing of electrical point machines and ground connection. This would include removal of old/existing point machine and fixing of new/overhauled motor . This would also include bringing the new machines from station / central cabin to site and taking the old / released machines from site to station/ central cabin. (Inspection Agency Consignee) | Numbers | 30.00 | 4,916.18 | 1,47,485.4 |
| 3 | Dismantling of existing signalling gears such as 1.CLS unit along with all accessaries, post with base 2.Location boxes & Junction boxes etc from station as decided by site In-charge and transportation of the same to consignee depot. (Inspection Agency Consignee) | Numbers | 20.00 | 699.44 | 13,988.8 |
| 4 | Cutting and removal of worn out location box withouth distrubing equipments housed in location box, fixing new moduler location box, as per instruction of side Engg. This include drilling of holes of required size at site with contractors own tools. Moduler location box will be supplied by Railways. (Inspection Agency Consignee) | Numbers | 10.00 | 6,196.51 | 61,965.1 |
| 5 | Replacment of old/ wornout ground connections of point machine by removing existing old/wornout ground connections along with P Bracket and fixing of new ground connection along with P brackets. This will also include neccesery adjestment as per instruction of Side Engg. (Inspection Agency Consignee) | Numbers | 30.00 | 4,050.49 | 1,21,514.7 |
| 6 | Repairing of location foundation with masonary work.This also includes cleaning the locations, sand filling inthe location and plastering inside the location.(Inspection Agency Consignee) | Numbers | 50.00 | 2,850.76 | 1,42,538 |
| 7 | Supply of Smoke detector(Optical)Apollo make or similar for firealarm system.(Inspection Agency Consignee) | Numbers | 20.00 | 4,266.13 | 85,322.6 |
| 8 | Sealed maintenance free VRLA battery set of 60 cells(stackable), in combination of 55+5 cells for SMPS basedIPS,each cell of 2VVolt/300AH capacity,fullycharged,confirming to RDSOSpc no. IRS S:93/96A amd 1or latest, complete withconnection links and suitabalynumbered in stackable racksalong with the mannuals. (Inspection Agency RDSO) | Set | 1.00 | 5,19,314.37 | 5,19,314.37 |
| 9 | Casting of cement concrete to protect S&Tequipments and laid cables, above pipes, Signalstore etc by concrete mixture of cement, sand,stone in the ratio of 1:2:4 using 25 mm gradedstone aggregate as per instruction of site incharge of railways. Concrete is to be casted withthe help of suitable size shuttering form as persite requirement. Concrete is to be cured forsufficient time as per standard practices onrailways (Inspection Agency Consignee) | cum | 50.00 | 4,342.61 | 2,17,130.5 |
| 10 | "VENUS ADJUSTABLE SPANNER 15"" /375MM PHOSPHATE FINNISH (Venus) Cast Iron conforming toGrade BM 310 of IS :2108-1977 (for light duty wrenches) preferably Drop Forged, Maximum opening of adjustable jaw (min 36 mm to 41 mm) + Tolerance(3 mm) make Taparia, VENUS, JK.(INDER Normal duty Type A PhosphateCoating Adjustable single ended open jaw wrench .(Inspection Agency Consignee)" | Numbers | 50.00 | 683.6 | 34,180 |
| 11 | Solid Carbide Coated Drill Dia 7.1mm For Track Drilling Dimensions are Dia 7.1X30X61 Shank - 9mm (Inspection Agency Consignee) | Numbers | 100.00 | 1,948.22 | 1,94,822 |
| 12 | Twist Adaptor 19mm weldon for 13 mm (part no. 210245FS(Inspection Agency Consignee) | Numbers | 50.00 | 873.81 | 43,690.5 |
| 13 | Drill twist H.S.S. for MORSE taper shank type N dia of drill bit 16 mm to IS 5103 / 1969 with amendement no. 1 to 3.(Inspection Agency Consignee) | Numbers | 50.00 | 485.12 | 24,256 |
| 14 | Nylon 66 Point insulations complete set With RDSO spec No-IRS S 40/84 or latest consists of 1.Gauge tie plate insulation one set (Insulating plate drg No. T-10372=01No, insulating bush drg No. T10368=03 Nos, insulating washer drg No. T-10371=06 Nos) 2. D bracket insulation one set (Insulating plate (RH) drg No. S-3265=01No, insulating plate (LH) drg No. S-3266=01 No, insulating washer drg No.S-8640=04Nos, Insulating bush drawing No.S- 23199=04Nos) 3.Stretcher bar insulation one set(Insulating plate drg No.T-10367=01No, insulating bush drg No.T-10368=02 Nos, insulating washer drg No.T- 10371=04Nos) 4. L-bracket insulation one set (Insulating plate drg No.S-8804=01No, insulating washer drg No. S -8640=02Nos, insulating bush drawing No.S- 8813=02Nos(Inspection Agency Consignee) | Set | 30.00 | 319.78 | 9,593.4 |
| 15 | POWER CONTACTOR 4 POLE 200AMP,1000V AC, COIL VOLTAGE 415V AC,2NO +2NC AUX CONTACTS, WITH SURGE SUPPRESSOR, AS PER SERIAL NO 3,AND ITEM NO K-01 & K-02,OF BILL OF MATERIAL OF RDSO SPEC NO RDSO/PE/ SPEC/AC/0184-2015 (Rev 1) USED FOR FEEDER CONTACTOR NET 1 & NET 2,AND CONFIRMING TO RDSO SPEC NO RDSO/PE/ SPEC/AC/ 0184 - 2015 REV-1,SUITABLE FOR LHB TYPE AC COACHES SWITCH BOARD CABINET. specn: RDSO SPEC NO RDSO/ PE/SPEC/AC/ 0184 -2015 REV- 1 GeM Contract No. GEMC- 511687732178189 dt.15/11/2024)(Inspection Agency Consignee) | Numbers | 2.00 | 16,500 | 33,000 |
| 16 | Supply of Rechargeable SMF Lead Acid Battery 12 Volt, 42 Ah. Warranty - 30 months, Make - Exide, Amron & Osaka or Similar make. (Inspection Agency Consignee) | Numbers | 50.00 | 3,929.4 | 1,96,470 |
| 17 | ELECTRIC OPERATED HEAVY DUTY DRILL MACHINE, ( Size 13-23 MM DIA) WITH HORIZONTAL DRILL STAND, MAKE:- RAILWOLF/BOSCH/BLACL DEEKER OR SIMILAR. (Inspection Agency Consignee) | Numbers | 2.00 | 24,780 | 49,560 |
| 18 | Soldering Iron - 25 Watts 230V (Make: Soldron or Themisto or Toni or Similar) FIRM'S OFFER MAKE/BRAND--Soldron or Themisto or Toni ONLY.(Inspection Agency Consignee) | Numbers | 10.00 | 295 | 2,950 |
| 19 | Supply of GLF Tape Abration resistance with masting compound in size of 51 mm x 1.27mm x 2.6 Mtrs Rolls of Stanvac Chemicals, Permacel, ICC, Nitco or 3 M make.(Inspection Agency Consignee) | Numbers | 30.00 | 1,950.08 | 58,502.4 |
| 20 | Twisted Drill size 13 x 19 mm (Part no. 5223118) (Inspection Agency Consignee) | Numbers | 50.00 | 2,570.04 | 1,28,502 |
| 21 | Track Transformer for Feed end 100 VA single Rail 50 Hz. With Primary Excise Duty --Tapping AS - P - 100-110V, Secondary Tapping AS S -1.5 - 6-10-13 Make Pradeep, Kapil, Reliance Elect. ACCEPTED MAKE Pradeep/Kapil/Reliance(Inspection Agency Consignee) | Numbers | 50.00 | 1,357 | 67,850 |
| 22 | "Copper Lug 25 sqmm with single hole for AFTC track lead As per Drg. No. R Excise Duty -- ST- 12090. Make - Braco, Dowells, Shakti, Fixwell. (Inspection Agency Consignee)" | Numbers | 1000.00 | 14.03 | 14,030 |
| 23 | M.S galvanized Split Pin as per IS:549/2002 size- 3/16 x 3" (Inspection Agency Consignee) | Numbers | 1000.00 | 2.14 | 2,140 |
| 24 | Battrey oprated drill m/c cutter 22.5mm Rail TCT Cutter 22.5x 55 mm(Part No: 240289 (Inspection Agency Consignee) | Numbers | 30.00 | 3,767.74 | 1,13,032.2 |
| 25 | Arrangment of battery operated rail core drill alongwith additional 18 mm TCT rail core drill.Maximum core cutting capacity 36mm,rated speed 250/450ZRPM, Battery type Li-on,Battery voltage 50V,Battery pack capacity 4AH,Number of battery supplied-2No. Charger-1No. Special design pressurised internal spindle cooling to give maximum life of core cutter by avoiding heating.3 sets of of 22,13,16,7.1 gauge drills adapters with drill bit is to be provided along with the machine.weight of machine with battery-18.5Kg Make- Eibenstok,Bosch,KPTL. (Inspection Agency Consignee) | Numbers | 1.00 | 1,92,430.14 | 1,92,430.14 |
| 26 | Repairing of CO2 Type fireextinguishers of 4.5 KGcapacity with pressure gaugeof various relay rooms with allother accessories (Inspection Agency Consignee) | Numbers | 20.00 | 2,634.51 | 52,690.2 |
| 27 | Digital current clamp meter to measure current leaksparasitic draws down to 1 mA and electric load from 1mA to 100 Amp AC/DC, and voltages from 0 to 600 VAC/DC, small jaw size to measure current in signalingcircuits, 4 digit display. make FLUKE/ GTC/KOICO orsuperior with better specification mentioned with allaccessories like test lead, batteries and carrying case,sample may got approved from consignee beforesupply. (Inspection Agency Consignee) | Numbers | 3.00 | 24,430.43 | 73,291.29 |
| 28 | DEFLECTOR PLATE COMPATIBLE WITH 60 KG RAIL WITH ALL HARDWARE ACCESSORIES FOR USE WITH DIGITAL AXLE COUNTER AS PER RDSO/SPN/177/2012 Version 3.0 or latest. 1 Number DEFLECTOR PLATE means 1 pair DEFLECTOR PLATE protecting one DP from both side. Firm's Offer : Make/Brand: "MEDHA" (Inspection Agency Consignee) | Numbers | 50.00 | 4,366 | 2,18,300 |
| 29 | Supply of wire tree for use in point machine as per drg RST-11435, wiring tree lugs are to be crimped & soldered (Inspection Agency Consignee) | Numbers | 100.00 | 469.72 | 46,971.93 |
| 30 | Supply of TRUE RMS DIGITALMULTIMETER OF MAKE &MODEL NO. FLUKE - 179/ESCORTS- 99/STANLAYSMM606. TECHNICALSPECIFICATION AS PERANNEXURE. (Inspection Agency Consignee) | Numbers | 3.00 | 14,991.04 | 44,973.12 |
| 31 | Wheel sensor with protection tube of Frauscher makeMSDAC type Rsr 180 (with BBIK- M 12 GS05 fixingalong with cable length of 5 mtr (GS05) (Inspection Agency RDSO) | Numbers | 5.00 | 1,57,922.64 | 7,89,613.2 |
| Schedule total | ₹37,14,096.55 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC_April-2022.pdf
ATTACHMENT
CORRECTIONSLIP1to11GCC2022_compressed.pdf GCC CORRECTION SLIP 1 TO 11
ATTACHMENT
FINALNEWTENDERDOC202697.pdf
ATTACHMENT
CORRECTIONSLIP1to11GCC2022_compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .