Renovation of 06 Nos Type I and 02 Nos Type II Quarters of Transport Department at Katchal including IEI.

Amount

Dismantling roofing including ridges, hips, valleys and gutters etcand stacking the material within 50 metres lead of:

Asbestos cement sheet

Providing and fixing precoated galvanized iron profile sheets (size shape and pitch of corrugation as approved by Engineer-in-charge) 0.50mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS:277 in 240 mpa steel grade 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns.sheet should have protective guard film of 25 microns minium to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDMseal or with polymer coated Jor l hooks, bolts and nuts 8mm diameter with bitumen and G.i limpet washers or with G.I. limpet washer filled with white lead complete upto any pitch in horizontal/verticla or curved surface excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gms as per IS: 277 in 240mpa steel grade ,5-7 microns epoxy primer on both side of the sheet and polyester top steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws or with polymer coated Jor L hooks, bolts and nuts and G.I. seam bolts and nuts, G.I plain and bitumen washers complete:

a) Ridges plain (500-600mm)

Providing valleys of 90cm wide overall in plain G.S. Sheet fixed with polymer coated J or L hooks, bolts and nuts 8mm dia. G.I. limpet and bitumen washers complete:

a) 1.60 mm thick with zinc cozting not less than 350gm/m2

White washing with lime to give an even shade

Old work (two or more coats)

Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade

Old work (one or more coats)

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade :

One or more coats on old work

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.

30 mm thick plain PVC door shutters

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:

Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length 15 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms

15 mm nominal bore

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete

Semi rigid pipe 32 mm dia

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws etc. complete

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing eaves or facia boards made with 12 mm thick PVC Board fixed with nuts and Bolts etc complete as facia board.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with piano tyhpe switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable etc as reqd. 'Group A'

Wiring for Circuit / Sub Main wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required.

a) 2 x 1.5 sq.mm + 1 x 1.5 sq.mm earth wire

b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire

b) 2 x 4 sq.mm + 1 x 4 sq.mm earth wire

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc., as required

Supplying and fixing metal box of 150mm X 75mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps piano type switch, connection, painting etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required.

Supplying and fixing 3 pin, 5 amps ceiling rose on the existing junction box / wooden block including connection etc as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Supplying of pre-wired for LED, power saving Decorative box type LED tube Batten fittings, 4' powder coated for LED tube 1x 20 W with ISI standards similar to HAVELLS regal batten T8 upto 1x22 w and crystal glass T8 LED tubelight G13 lamp holder of 20 w or equivalent.

Supplying of LED Retrofit Bulbs 9 Watts B22 (Cool Day Light) with ISI standards Similar to HAVELLS ADORE 9 w CDL or equivalent

Supplying of Energy Saving 5 star rating, with ISI, A.C. Ceiling fan 1200 mm sweep, with all accessories and Step type electronic Fan regulator. (Similar to HAVELLS Efficienia neo BLDC 26 W 5 star).

Supplyiong of integrated LED Bulk Head Luminaire, 10 w comprises of PDC A1 housing and milky diffuser similar to C & S SIRIUS series LED Bulk Head CAT No. LTB10WLED or equivalent.

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connection etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring with the down rods of standard length (up to 30 cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable etc. as required.

Supplying of Exaust fan of size 300 mm sweep, Metallic Blades with protective bird guard (similar to HAVELLS Ventil Air DB or equivalent with ISI).

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

a) Upto 450 mm sweep

Extra for fixing the louvers / shutters complete with frame for a exhaust fan of all sizes.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

a) 08 way, Double door

Supplying and fixing 5 amps to 32 amps rating, 240 /415 volts, 'C' curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. A) Single pole

Supplying and fixing following rating, double poles, 240 volts, isolater in the existing MCB DB complete with connections, testing and commissioning etc. as required. A) 40 Amps

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.