RESURRECTION OF EXTERNAL WATER SUPPLY SERVICES FOR MAP Ph 2 MILITARY FARM AND SHIVAJI LINE AT MEERUT CANTT

Amount

Excavation in trenches in soft/lose soil n.exc. 1.5M wide & n exc 1.5M deep for laying of GI/CI pipe line & getting out including forming bottom surface all as specified and directed.

Returning, filling in, trenches including spreading, levelling, watering and well ramming in layer n.exc. 250 mm in any type of soil after the pipe laid & tested complete all as specified and directed.

Removing excavated surplus soil to a distance n.exc. 50mtr and depositing where directed at a level n.exc. 1.5 m above the starting point all as specified and directed

M & L Ductile iron pipes with spigot and socket ends, centrifugally cast (spun) class K9, in any length, externally coated with metallic Zinc Coating finished with bituminous paint complete all as specified of the following bore:- Note :- Excavation, earthwork and GI clamps shall be measured and paid separately)

(a) 250mm dia

(b) 150mm dia

(c) 100mm dia

M & L DI/CI Specials class B as per IS such as bends, tappers,any type branches cross all sockets and spigot collar caps and plug 200mm to 300mm bore all as specified and as directed

Same as item no.9 but upto 150 mm

M&L for joints for water mains DI spigot and socketed pipe specials and fittings with Rubber gasket for the size 250 mm dia bore complete all as specified and directed.

(a) same as item no 11 but 150 mm dia bore

(b) same as item no 11 but 100 mm dia bore

M&L to Supply, installation, testing and commissioning of Sluice valves flanged of class 1.6 PN all as specified and as directed as per following sizes:

(a) 250 mm dia

(b) 150 mm dia

(c) 100 mm dia

(d) 80 mm dia

M&L for fixing C.I. Air release valves with two air outlets 150 mm Dia and fixing up on water supply main (with cap) complete with bolts, nuts, rubber insertions etc.

Supply and fixing Gun-metal globe or gate valves, with 2 iron wheel head, screwed both ends for iron pipe and fixed

a) 50mm dia bore

a) 20mm dia bore

M&L for Construction of brick was only valve pit of size 1200x1200x1200mm (Internal dimensions ) including all excavation and earth work in any type of soil and disposal of soil to a distance of not exciting 50mtr and depositing all as directed including 10mm plastering internally in CM 1.4 PCC 1:2:4 100mm thick at bottom and top of valve pit, and MS Sheet 3mm thick at with angle iron frame 35X35X5mm and 40X40X5mm at bottom for minting and MS sheet cover inlet. Handle locking arrangement with 1 No. lock with two keys NAVTAL/GOODREJ/HARRISION ON 50mm inlc two coats of synthetic enamel paint (Make Asian Ist quality ) over a coal of red oxide primer on steel surface complete all as shown on drg Bo. TIVEM/12 sheet 1/1 and as specified

M&L for Construction of brick was only valve pit of size 950x950x950mm (Internal dimensions ) including all excavation and earth work in any type of soil and disposal of soil to a distance of not exciting 50mtr and depositing all as directed including 10mm plastering internally in CM 1.4 PCC 1:2:4 100mm thick at bottom and top of valve pit, and MS Sheet 3mm thick at with angle iron frame 35X35X5mm and 40X40X5mm at bottom for minting and MS sheet cover inlet. Handle locking arrangement with 1 No. lock with two keys NAVTAL/GOODREJ/HARRISION ON 50mm inlc two coats of synthetic enamel paint (Make Asian Ist quality ) over a coal of red oxide primer on steel surface complete all as shown on drg Bo. TIVEM/12 sheet 1/1 and as specified

M&L for Road cutting/PCC and hard standing depth not less than 60cm for laying water suppl and width not less than 45 cm for laying water supply pipe and making good surface with PCC.

M & L cement concrete type B-1 1:2:4 (20mm grade stone aggregate) as in door cills, path and plinth protection (of any section)including chambers, weatherings, throat-ing etc and setting in mortar complete all as specified and directed.

Supply & fix G.I. Pipe medium grade with all fittings fixed with suitable iron clamps with grouting on walls and ceilings or laid on floor including cutting of GI pipe to make suitable length for laying of following sizes. Note : Earth wk shall be measured and paid seperately under relevant items.

(a) 50 mm dia pipe

(b) 20 mm dia pipe

Development of tube well with compressed air and after with 25% extra capacity pump by pumping muddy water.

Yield test for bore well by continuously pumping for 16 hours to determine sage pumping yield.

S&F, Submersible pump, electric driven 415 V TP suitable for 250 mm dia bore well (casing pipe size 300/350 mm) supplied installed, suitable for 71 mtr Head and discharge not less than 1000 LPM complete all as specified and directed by Engr-in-Charge. Qty 4 Nos (1x No for Each Borewell)

Material and labour for submersible flat copper cable 3 core 25 Sqmm multi stranded for 4 Nos Pumps (160mtr for each Bore well)

Supply install testing and commissioning Chemical Dosing System suitable to inject solution upto 25 LPH comprising dosing pump coupled with single phase electric motor of capacity 0.5 HP, 1440 RPM assembly inluding DOL starter suitable capacity with Agitator dosing and agitator in single motor, agitator with SS sweep blade duly FRP coated, FRP double tank 150 ltrs capacity, complete unit mounted on heavy duty MS fabricated frame duly anti corrosive paint including packing, electrical & plumbing works etc. complete all as specified and directed by Engr-in-Charge. Note: (i) The cost of electrical connection like point wiring and socket point required for smooth functioning of dosing plant and T&P shall be included in quoted rates.

Supply, Installation, Testing and commissioning LT panel of Indoor type CPRI approved made out of 2.0 mm thick CRCA sheet front side openable with powder coated paint over a coat of red oxide primer including seprate chamber for bus bar and chromium plated cable glands of different sizes including connecting the out going and incoming MCCB's with insulated aluminium strip suitable for three phase four wire system fixed on M S channel/ angle iron frame over 30 cm from ground level with PCC and comprising the following:- (i) Alumunium Busbar 200 Amps with air insulated for 3 phase 4 wire system - One set. (ii) Incoming MCCB 63 Amps, adjustable thermal megnatic, FP 440 volt 36 KA - 01 No (iii) Outgoing MCCB 50 Amps, Adjustable thermal megnatic FP 440 volt 36 KA - 01 Nos (iv) Outgoing MCB 20 Amps SPN 230 volt 10 KA - 02 Nos (v) S&F, Fully automatic star Delta starter, 3 phase 415 volts suitable for 45 HP submersible pump including connecting with pump - 01 Nos (vi) Phase sequence suitable for 3 phase for 45 HP (vii) Single phase preventer suitable for 45 HP pump (viii) Indicator lamp LED type - 3 Nos (1 set R,Y & B) (ix) Digital Voltmeter - 01 No (x) Digital Amp meter - 01 No (ix) Panel wiring with copper cable 2.5 sqmm PVC insulated single core with suitable CTs - 1 Job

Supply, Installation, Testing and commissioning LT panel of Indoor type CPRI approved made out of 2.0 mm thick CRCA sheet front side openable with powder coated paint over a coat of red oxide primer including seprate chamber for bus bar and chromium plated cable glands of different sizes including connecting the out going and incoming MCCB's with insulated aluminium strip suitable for three phase four wire system fixed on M S channel/ angle iron frame over 30 cm from ground level with PCC and comprising the following:- (i) Alumunium Busbar 400 Amps with air insulated for 3 phase 4 wire system - One set. (ii) Incoming MCCB 200 Amps, Adjustable thermal megnatic FP 440 volt 36 KA-01 No (iii) Outgoing MCCB 100 Amps, Adjustable thermal megnatic FP 440 volt 36 KA-02 Nos (iv) Outgoing MCB 32 Amps SPN 230 volt 10 KA -04 Nos (v) Fully automatic star Delta starter, 3 phase 415 volts suitable for 45 HP submersible pump including connecting with pump - 01 No (vi) Phase sequencer suitable for 3 phase for 45 HP (vii) Single phase preventer suitable for 45 HP pump (viii) Indicator lamp LED type - 3 Nos (1 set R,Y & B) (ix) Panel wiring with copper cable 2.5 sqmm PVC insulated single core with suitable CTs - 1 Job (x) Digital Voltmeter - 01 No (xi) Digital Amp meter - 01 No (xii) Digital water level indicator with battery backup and suitable multicore cable OHT to panel with all connected items complete to make functional - 01 No

M&L LED Avaitation obstruction light luminaires aluminium alloy housing 5 paralle circuit maximum 10 - 12 w consumption incl suitable lamp and fixed with suitable size of the GI pipe and 50 X 6 mm flat iron clamps complete including electrical connection copper conductor two single core cable 2.5 Sqmm drawn in steel conduit with all accessories such bends, elbows,tee etc. from panel to light fitting fixed on RCC over head tank with shadles and rawel plug approximally 25 Mtr ht all as specified and directed, Mako:- Bajaj or Equivalent (Cal part No BJAOL A/LI 600)

M & L aluminium air termination rod three pointed 12mm dia 1000mm long with a drilled base plate of size 30x30x5mm to fix vartically on top overhead reservoir and connected to two independent earth strip complete all as specified and directed by Engineer-in-Charge

M & L Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed by Engineer-in-Charge

M & L for Galvanised iron strip size 32X6mm buried in ground and fixed with PVC sanddles and screw to route/columns of RCC/steel cver head reservoir and connection to two indeperedent earth strip complete all as specified.

M&L for Earthing complete with GI earth plates electrode 600x600x6mm thick burried directly in ground earth pit not less than 2.5 mtr deep below ground level surrounded with adequate quantity of charcoal dust mixed with salts to a packet thickness of 15 cm all around the plate,using Gl earth strip 32x6mm connected to earth plate by means of nut,bolts and washers as directed GI pipe light grade 50mm bore on water pipe from earth chamber to upper edge of earth plate,Cl funnel with wiremesh fixed on water pipe and PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in pit chamber and RCC pitcover 50mm thick pre-cost RCC 1:2:4 type B- 1 dully rainforced with MS bars 6mm dla @150 cc both ways with 10mm dla MS bar in lifting handle excavation earth work Including laying of Gl pipe in walls etc including testing point all as directed in electrical plate No. 3 of SSR pt I complete all as specified and directed.

M&L for taking out old unserviceable submersible pump from borewell and deposited in MES store with in 20 Km of radius completed all as specified and directed by Engr-in-charge.

M&L for Disconnecting and taking up old existing DI/GI water pipe pipe lines and connections in any posisition of trenches / under floors/ on walls including all fittings etc all as directed and specified for the following sizes :-

(a) 250mm dia

(b) 150mm dia

(c) 100mm dia

M&L for relaying and refixing, spigot/socketed/flanged, existing DI pipes only with all connected joints with rubber gaskets to make serviceable only in trenches under floors of any type and length, of following size:- Note:- Serviceable pipes retrieved under Srl item no 43 here in before shall be reused. Joints and special fitting shall be measured and paid for separately.

(a) 250mm dia bore

(b) 150mm dia bore

(c) 100mm dia bore

M & L for flushing of existing DI/GI choked/blocked water pipe lines by using pressure water and suitable T & P up to 40 Mtr length complete all as specified and directed. Note : Earth wk shall be measured and paid seperately under relevant items.

(a) 250mm dia bore

(b) 150mm dia bore

(c) 100mm dia bore

M&L, Laying only GI tubing, medium grade, including new threading of pipe 100mm dia, laid in trenches or laid under floors, fixed on walls with and providing clamps etc complete all as specified & directed. Note:- GI pipe 100 mm shall be issued under Sch 'B' store and excavation qty to be measured and paid seperately under respective items.

M&L for Cutting of CI/DI Pipes and reducing to required length before laying in position for insertion of new tees, branches etc complete all as specified & directed. For following sizes Note :- Fittings will be measured and paid for separately under respective items

(a) 250mm dia bore

(b) 150mm dia bore

(c) 100mm dia bore

M&L for making a bore holes in DI/GI pipes of any sizes for making any branch connections upto 50mm GI pipe complete upto raising lines of building including providing suitable iron clamps for connection with rubber washers and nipple/sockets etc. complete all as specified and directed. Note : Earth wk shall be measured and paid seperately under relevant items.

Supply installation Testing & Commissioning of ECO friendly Diesel Engine driven generating set outdoor type of capacity 125 KVA, CPCB-IV nearest higher side 400/440 volts, AC 3 phase, 50 HZ , 4 wire, 0.8 PF directly coupled alternator and engine water cooled with common steel base fixed on Cement concrete in foundation as per OEM recommendation DG set of 125 KVA platform with inbuilt AMF panel with 2 nos suitable size of contactors as 01 no for main supply and 01 no for DG supply as per manufacturer recommendation and other accessories comprising of the following. Note :- The Plinth should be as per Manufacturer Recommendation and the rate of plinth is deemed to be included in quoted rate of item.

a) ENGINE- ECO friendly for emisson and noise (PCB NORM COMPLIACE) 4 stoke diesel Engine confirming to BS std developing, 1500 RPM turbocharged watercooled complete with a provision for 10% overload for one hour on 125 KVA. (i) Fly wheel with starter ring for generating set. (ii) Dry type Air filter. (iii) Lub oil cooler assembly (iv) Exhaust air manifold. (v) Exhaust silencer. (vi) Expension bellow. (vii) Exhaust gas turbocharger. (viii) Lubrication oil filter (ix) Electrical starting system with starting motor & battery charging alternator with self starter and other auto electic accessories as recomanded by manufacture. (x) Centrifugal by-pass filter. (xi) Front & rear engine mounting supports. (xiii) Engine control panel consisting of OFF/ON/START keys lub oil pressure gauge, Ammeter, electronic Hour meter, speedometer. (xii) Safety against low lub oil pressur (xiii) Engine operation/Maintenance, spare parts Manual. (xiv) Engine test certificate. (xv) Cold starting kit (xvi) Mechanical Governer (xvii) Provision of oil filter, fuel filter, engine oil etc. (xviii) Integral set mounted radiator system.

b) ALTERNATOR- Sailent pole brushless copper wound type suitable for direct couple to engine self excited, self regulated with fast response thyristor type electronic automatic voltage withhold out put voltage with in desired limit(+1%) Dynamically balanced 400/415 volts AC 3 phase 50 HZ, 4 wire 0.8 PF lagging 125 KVA 1500 RPM star connected (4 wire) screen protected drip proof enclousers with radial fan mounted on rotor with insullation class- H suitable for ambient temperature varies from -4 degree C in winter to 50 degree C in summer (Meerut) with following accessories. (i) One MS frame suitable for mounting of Engine & alternator. (ii) Fuel tank of suitable capacity as per Manufacturer recommendation complete with fuel gauge inlet/outlet connections drain valve with plug etc. (iii) Battery of suitable capacity as per manufacturer recommendaiton with copper leads and terminals of suitable size (iv) One set of AVM pads fitted on base frame.

C) Acoustic enclosure- Supply & install of Acoustic Enclosure suitable for 125 KVA DG set the degree of protection IP-42 conforing to IS - 2147 as under. (i) Fabricated out of CRCA sheet of suitable thickness as per manufacture design. Polyster based powder coated internaly and externaly with lockable type door handle. All nuts and handles shall be zinc coated. (ii) The doors are gasketed with EPDM gaskets. (iii) Sound proofing with high quality rock wool/mineral wool confirming to IS 8183 of 50mm thickness and density at 96 Kg /M3 coverd with fiber glass cloth and perforated powder coats sheet specialy designed allenuators (Sound controller) at air entry and exit of the container noice level shall be not exceed 75 Db at 1 meter distance as per CPCB norms. (iv) Adequate ventilation to meet air requirement for combustion and heat removal with provn of a blower. (v) Emergency stop push button out side the container. (vi) Provn of light inside the canopy 20W LED fitting with wiring and control switch. (D) Testing and commsissioning : Contractor has to made arrangement for testing of DG Set in presence of Rep/IEM detailed by accepting officer for continuous running of 12 Hours out of which 1 hours running at 110% of rated capacity of generator. Necessary load and diesel will be agranged by the contractor, no any extra cost given to the contractor.

Supply, Installation, Testing and commissioning LT panel of Indoor type CPRI approved made out of 3.15 mm thick CRCA sheet front side openable with powder coated paint over a coat of red oxide primer including seprate chamber for bus bar and chromium plated cable glands of different sizes including connecting the out going and incoming MCCB's with insulated aluminium strip suitable for three phase four wire system fixed on M S channel/ angle iron frame over 30 cm from ground level with PCC and comprising the following:- (i) Alumunium Busbar 400 Amps with air insulated for 3 phase 4 wire system - One set. (ii) Incoming MCCB 200 Amps 440 Volt 50Hz, adjustable thermal megnatic, FP 36 KA - 01 No (iii) Digital Amp meter -01 No (iv) Digital Voltmeter - 01 No (iv) Indicator lamp LED type - 3 Nos (1 set R,Y,B) (v) Panel wiring with copper cable 2.5 sqmm PVC insulated single core with suitable CTs - 1 Job (vi) On Load changeover switch 200 amp to fix inside the panel.

Supply, laying UG cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured heavy duty electric power cables 1100 Volts grade with stranded aluminium conductor of size 120 Sq mm 3.5 core

Supply and lowering in borewell, MS ERW column pipe 150mm bore in 3 mtr length both end flanged with MS flanges 10mm thick with cut for passing the submersible cable and four no of holes 10mm dia with suitable size of covering nuts, bolts, washers and rubber gasket complete all as specified and directed. Note :- All arrangements and T&P required for lowering the column pipe in the bore shall be made by the contractor under their own arrangement at no extra cost.

M&L for seven stage cleaning and sterilization inside the existing RCC overhead tank of capacity of 100000 gallon through bacteriological and fungal treatment by using sodium hypochlorite, potassium permanganate /E-in-C's Branch approved chemical as recommended by Engr-in-Charge and ULTRA VOILET RAY at Pump house at any height (as per site requirement), including suitable staging/scalfolding seven stage are as under follows:- (a) First stage is to drain out the water by using high capacity pump of dewatering system. (b) Second stage is cleaning all the stage formation inside the tank by using sodium hypochlorite a laboratory tested branded chemical/ E-in-C's Branch approved chemical as recommeded by Engr-in-Charge. (c) Third stage is scrubbing the walls and floor with mechanised scrubber and fresh water cleaning high speed jet pump (Rotary & flat) to remove all scalling algae abd other formed particlaes on internal surfaces of the tank completely. (d) Fourth stage and first fungal screening is sterilization by using potassium permangate, Laboratory certified and tested chemical E-in-C's Branch approved chemical as recommended by Engr -in-Charge, test certificate from government laboratory monitoring suitability for sterilization should be submitted to the office before using stralisation. (e) Fifth stage is cleaning the floor of water tank by heavy duty industrial vaccume cleaners and sludge succor having maximum 1200 watt with suitable heavy duty rugged motor to free any foreign and loose particales of any nature (f) Sixth stage is providing UV radition which shall have 360 degree off sterilization with in the tank to kill all suspended bacteria (The radition shall portable and effective for sterilization of drinking water tanks for diminetion of floeting and suspended bacteria.) (g) Seventh stage of cleaning is to sterlizes the floor of the water tank by using branded strong oxidizing agernt non toxic bio-degredable eco-friendly anti-bacterial agent (high potency sodium hypochlorite) certified by a Govt. approved laboratory to disinfect the over head tank from all harmful pathogens. (h) Cleaning of, lid wall of the tank, structure for all scales and other particles any algae, hives and any type of vegetation of any other unwanted matters.

All as per item No 68 above but the capacity of the tank is 132000 gallon

Testing of water sample , chemical, biological and physical including hardness, turbidity, E-coli, coliform from a NABL accredited lab Note:- Contactor shall arrange for collection of sample from MAP Ph-2 (Military Farm South And Shivaji Lines pump houses) in clean glass container properly sealed and send the same to the lab with - in 04 hrs of collection and to submit report in office for perusal of Engr-in-Charge.

Supply, Installation & Commissioning of SCADA Compatible programmable RTU Panel with with required IOs & 7'' HMI ARM 7 processor, GSM Based Remote Terminal Units with Analog and Digital parameter and features as specified to store and transmit data on GSM/GPRS as Backbone to control room with UPS 1 Hr Backup & suitable for Instruments, and Motorised Valves and Pumps with IP55 MS Powder coated enclosure made out of 1.6mm CRCA Sheet.

SITC of Level Transmitter (Range: 0-10mtr)

SITC of Residual Chlorine sensor and transmitter of 0-20 ppm (required replacement of sensor at every two year required budget during O&M for 10 years) and 4-20 mA/RS-485 output with Flow cell arrangement and SITC of Chlroine Dosing Pump with 6 LPH, 0-5 Kg/cm2 rating, with 100 Ltr tank, level switch and Feedback Control panel integrated with Chlroine sensor and stirrer motor

SITC of Pressure Transmitter with 0-10 Bar range with Suitable accessories

SITC of Full bore Electromagnetic flowmeter with SS304 Flow sensor, CS body, SS316L electrode, PN10, IP67 transmitter and IP68 sensor with RS-485 output with Integral/Remote type transmitter 150MM

SITC of Motorised Butterfly valve PN10 and Neoprene/Hardrubber caoting on Disc, Disc material CI, Single Phase/ 3 phase actuator suitable for the valve with canopy and direct/In direct mounting type

Integration & Monitoring of Existing Tubewell with the new SCADA software system

SITC of XLPE cable with copper conductor and with all required accessories i.e. Cable tray, cable tray support, PVC Conduit etc.

SITC of Chemical Earthing

B/R PART

Surfaces ecavation n,exc 30 cm deep and averaging 15 cm deep and getting out hard/dense soil

M&L hardcore broken stone or boulders of gauge n,exc 63 mm deposited spread and levelled in layers n, exc 15 cm thick watered and rammed ta a true surfaces surfaces

M & L for 75 mm thick PCC type D-2 1:4:8 (40 mm graded aggregate) as in sub base complete.

M&L sand filling 30 m thick under the interlocking tille water and consolidation complete

M&L for coloured Machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness M-35 grade concrete all as specified and directed

M&L cement concrete in roof kerbs or muds stops rounded or chamfered typeB1 1:2:4 ( 20 mm graded aggregate )

Taking down cement plaster on brick or concrete or stone walls surface including racking out joints, hacking for keys, scrubbing down with water etc complete all as spd and directed.

Materials & labour for applying 15mm thick in cm 1:4 on brick walls or concrete surface of finished even and fair all as specified and directed.

Demolition of brick work or stone/boulder masonry laid in cement mortar in any description as directed.

M&L for brick work with brunt bricks straight or curved on plan to any radius built in CM 1:6 all as specified and directed by Engr -in-Charge

M&L for preparing new plastered surface of wall and applying two coat of cement base paint over a coat of primer etc all as specified and directed by Engr -in-Charge

Complete removal of existing treatment from walls , pillars and cornices washing, rubbing down and stopping of distempered and painted surfaces and cleaning the entire area(existing treatment may be of either two coat oil bound distemper /enamel paint) and making the wall surface smooth and all as specified and directed

M&L preparing old cement base distempered surfaces of walls by washing, rubbing down and stopping of surfaces and applying two coats with cement base paint , white or tinted including and washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified .

M&L preparation of old plastered or unplastered surafces of ceilings and applying two coats of white wash including washing floors, cleaning glass, joinery,electrical fittings, wiring etc. , of drops and splashes complete all as specified .

M&L PCC 1:3:6 type D2 ( using 40mm graded crushed stone aggregate) as in foundation filling sub base and mass concrete all as specified.

S&F Hand rail, half round or other section or core for wooden hand rail straight portion drilled and countershunk for baluster,nosing to steps including embeding in concrete and screwing etc,wind ties for roof including screwing bolts,post and struts running bars for doors, post and strut in fencing including cutting top to shape as directed, drilling hole for wire etc, Flat iron fillet for wire mess and similar work, confirming to Fe-290 Grade E -165

S&F in repair galvanized two strand steel barded wire 2.24 mm dia barbed with 2mm dia barbs of 75mm specing and straining and fixing to any type of standard rails standing bolt including securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins etc complete all as specified and directed ( Each line measured separately)

S&F 3mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty (or beading ) in square n.exc 0.5 Sqm in each panes complete

Materials & Labour for preparation of new steel surface of any description not otherwise described exc 10cm width or girth and applying two coats of synthetic enamels paints over a coat of red oxide primer all as specified.

M&L preparation of old painted steel and iron surfaces of any description , not otherwise described ,over 10 cm width or girth and painting one coat with synthetic enamel including cleaning, stopping and rubbing down and removing all drops , , dirts etc. complete all as specified.

Removing buiding material like sand ,aggregate soil and old debris to a distance upto 1 Km beyound the lead included rate including loading and unloading and stacking destination complate

Taking down Chowkats or frames not exc. 1.5 Sqm each, with shutters (without taking off shutters from the frame).

Taking down shutters of any description exc 1 sqm and n,exc 2 sqm

M&L plain framed panelled shutter ( two Panel) 2nd class HW and style 35 mm thick with lockrail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces . The size of rail and stile as per IS 1003 ( Part I ) kiln seasoned and chemically pressure treated

Supply & Fixing PVC door frame (50x47) mm made out of plain colour5 mm thich PVC Sheet re in forced with MS Square Tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick ( Style ) consisting of frame made out of MS Tubes for top & bottom rails.MS frame shall be covered with heat moulded plain colour PVC ' C 'Channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC Sheets for top rail , lock rail & bottomrail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC Sheet to be fitted in the MS Frame welded / sealed to stiles & rails with suitable PVC Sheet beading, jointed together with solvent cement,supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F for 300mm length of bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cost aluminium alloy all as specified and directed.

S&F for 150mm size extruded aluminium alloy handles, fabricated type, anodised all as specified and directed.

S&F for aluminium, anodised barrel tower bolt of extruded section and fixed 150mm of size all as specified and directed.

S&F 150 mm overall length of cover plate floor dooe stopper of aluminium alloy body and tougue with hard drawn steel spring

S& F 18/19 thick prelaminatd particle board interior grade, prelaminated one side with decorative choice lamination & other side balancing whie lamination fixed with screws to timer frame work

S&F Hasp staple aluminimum anodised 150 mm long

S&F 500 litre capacity water tank rotational moulded polyethylene water storage tanks( cylindrical/vertical with closed top ) hoisted and fied in position all as specified and directed including 20 mm float vavle with aluminium rod complete

Supply & fix 15 mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including Taking up or down GI steel tubing, etc complete all as specified & directed.

Supply&fix 20mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including taking up or down GI steel tubing,etc complete all as specified & directed.

S&F15mm bore pillar tap, long shank, swan neck, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts complete all as specified & directed.

S&F 15 mm bore bib tap chromium plated, cast copper alloy, with crutch or butterfly handle, flange, screwed down for iron pipe or for brass ferrule, complete all as specified and directed.

Supply and fixing PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC long bend for squat pattern etc , set with concrete and making good to floor. complete all as specified.

S&F Vitreous China wash basin, white, flat back, size 550 x 400 mm, including fixing acessories like galvanised brackets & plag bolts,32 mm CP waste coupling complete all as specified.

Supply & fix PVC connections of 600mm long Make suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed.

Supply and fix PVC waste pipes of 40/32mm bore suitable for wash hand basins/sinks complete all as specified & directed.

Supply & fix steel C.P. grating 100 mm dia waste pipe hole fitted as required at site complete all as directed by Engineer-in-Charge.

S&F 15 mm bore angle cock, chromium plated, cast copper alloy, screwed down with crutch or butterfly handle screwed both ends, as in repair including flench complete all as specified & directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtrs deep and getting out in any type of soil for foundation of manholes etc complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers soil not exceeding 25 cm thick complete all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point, spreading and leveling complete all as specified and directed.

PCC 1:4:8,Type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed by Engineer -in-Charge

Demolition and breaking up drain pipes (salt glazed stone ware) set in cement mortar in 150 mm dia including concrete bed & haunching where required and removing away as directed and specified.

PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in bed of drain pipes 150mm bore, laid to falls including packing under and haunching against the sides of pipes after they are laid and tested as specified and shown on drgs.

150mm bore salt glazed stone ware grade ‘A’ drain pipes, jointed on concrete bed complete including testing all as specified and directed by Engineer-in-Charge.

Pre cast reinforced cement concrete 1:2:4 , type B-1 (using 20mm graded crushed stone aggregate) as in manhole cover slabs including necessary form work complete all as directed by Engineer-in-Charge (Reinforcement shall be measured and paid for separately).

M&L for Preparing old plastered or unplastered surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots Washing, rubbing down and stopping of distempered and painted surfaces applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior weather proof paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm complete all as specified. Note :- The rate quoated including scaffolding upto 4 storeys of over head tank( Approx 13.2 M Hight)

M&L for Preparing old plastered or unplastered surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots Washing, rubbing down and stopping of distempered and painted surfaces applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior weather proof paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm complete all as specified.Note :- The rate quoated including scaffoldingi five to nine storeys of over head tank( Approx Hight from 13.2 to 26.4 M)

V r traders (BID ID -3332036)

BHARAT ELECTRICAL TRADERS (BID ID -3332026)

Shikhar ji Enterprises (BID ID -3332285)