REPAIRS TO B/R RELATED WORKS IN HANGERS OF ARMY AVN SQN INCLUDING TECHNICAL AREAS IN AOR OF AGE B/R LEKHANAGAR UNDER GE NASIK ROAD.

Amount

Demolition of concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) and removing the debris out of MOD land.

M&L for 75 mm thick Plain cement concrete, 1:4:8 type D-2(using 40mm graded aggregate) as in sub base. Note:mixing of concrete by machine only.

M&L for 50 mm thick Plain cement concrete, 1:4:8 type D-2(using 40mm graded aggregate) as in sub base. Note:mixing of concrete by machine only.

M&L for 100 mm thick Plain Cement concrete 1:2:4 type B-1(using 20mm graded aggregate) as in flooring over and including provision of pvc 2 mm thick dividing strip for joints.complete all as per SSR Part-I. Note:mixing of concrete by machine only.

M&L for broken stone/boudlers as in Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by engr-in-charge.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering. Note.Moorum to be brought out of MOD land.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;over and including provision of PCC 1:2:4 type B0 as in filleting/edging to the sides of paver path/hardstanding in size and shape as directed by engr-in-charge.

M&L for Chequered cement concrete tiles with grey cement and pigment 30cm x 30cm x 25mm thick, with rubber moulded glossy finished surface, laid in floors over and including 15mm thick cement mortar screed bed in cement mortar 1:6, set jointed and pointed in neat cement slurry in floors.over and including provision of PCC 1:2:4 as in filleting/edging to the sides of paver path/hardstanding as per standard engineering practice to the entire satisfaction of engr-in-charge.

M&L for Rough Shahabad stone 25 mm to 30 mm thick in flooring/plinth set and jointed in in neat cement slurry and pointed in CM 1:4 complete all as specified and directed over and including 15mm thick screed bed in cement mortar 1:6.over and including provision of PCC 1:2:4 as in filleting/edging to the sides as per standard engineering practice to the entire satisfaction of engr-in-charge.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar and removing the debris out of MOD land.

M&L for 18 to 20mm thick Granite of any type work (table rubbed and polished) in steps, jambs pillars, window cills cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match.complete all as specified and directed.

M&L for Machine cut cudappah stone slab 20-25mm thick over 10 mm thick cement screed base in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Dismantling of precast concrete articles and precast concrete block set or built in cement mortar and removing the debris out of MOD land.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete over and including two coats of synthetic enamel paint over a coat of primer.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc.and removing the debris out of MOD land. Note:work is to be executed at any height and situation.

M&L for brick work with fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 inlcluding raking out joints on both faces of wall and curing as per standard eng practices.curing as per standard eng practices. Note.work is to be executed at any height and situation.

Demolition of concrete in any description and in any position.

M&L for Plain cement concrete 1:4:8 type D-2 (using 40 mm graded aggregate) as in foundations, filling and mass concrete over and including preparation of surfaces.

M&L for PCC 1:3:6,type C-2(using 40 mm graded stone aggregate) as in foundation,filling and mass concrete complete all as specified and directed.

M&L for Providing, cement concrete type B1 1:2:4 (20 mm graded aggregate) in copings and the like including weathering, slightly rounded or chamfered angles and throating, as directed and finishing the surfaces of concrete.

Taking down completely cement or cement lime plaster, any description on brick or stone walls/ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc. Note: work to be executed at any height and situation.

M&L for Rendering 15 mm thick in cement mortar 1:4 on brick wall/concrete surfaces finished fair and even. Note: work to be executed at any height and situation.

M&L for rendering 10mm thick in CM 1:6 on brick wall/concrete surfaces finished fair and even.

M&L for applying one coat of exterior primer on wall surface including preparation of surfaces i.e by scrapping,rubbing washing and filling cracks with crack seal to the entire satisfaction of ground executives. Note : work to be executed at any height and situation.

M&L for applying one coat of exterior primer on ceiling surface including preparation of surfaces i.e by scrapping,rubbing washing and filling cracks with crack seal to the entire satisfaction of ground executives. Note : work to be executed at any height and situation.

M&L for applying one coat of exterior emulsion paint on wall surface. Note:work to be executed at any height and situation.

M&L for applying one coats of exterior emulsion paint on ceiling surface. Note:work to be executed at any height and situation.

M&L for two coats of cement base paint on brick wall surfaces over a coat of primer including preparation of surfaces and curing as per standard eng practices. Note:work is to be executed at any height and situation.

M&L for applying two coats of distemper oil emulsion on wall surfaces.

M&L for applying two coats of distemper oil emulsion on Ceiling surfaces.

M&L for 1.00 mm thick acrylic wall care putty on wall surfaces incl preparation of surfaces,filling holes and cracks with putty,rubbing,making surface even to the entire satisfaction of ground executives.

M&L for 1.00 mm thick acrylic wall care putty on ceiling surfaces incl preparation of surfaces,filling holes and cracks with putty,rubbing,making surface even to the entire satisfaction of ground executives.

M&L for applying one coats of interior primer over wall surfaces as per manufacutrers instruction.

M&L for applying one coats of interior primer over ceiling surfaces as per manufacutrers.

Dismantling wrought iron or mild any description such as steel gate, steel frame works, purlins, rafter, railings, balusters and window guard bars and directed by Engr-in-Charge. Note : work is to be executed at any height and situation.

S&F steel work in tubular pipes including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 4923:1997 Grade YSt-210 complete all over and including two coats of synthetic enamel paint over a coat of red oxide primer. Note : work is to be executed at any height and situation.make as per PS.

Dismantling Plain or corrugated steel sheeting of any gauge,thickness,including Nainital or similar pattern roof coverings complete all as specified and as directed.

S&F Prepainted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed. Gap between wall face and sheet if any shall be sealed using CM 1:3 with WPC.quoted rate deemed to be inclusive of the same. Note : work is to be executed at any height and situation.

S&F Prepainted Galvalume aluminium zinc coating GI based Plain sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed. Note : work is to be executed at any height and situation.

M&L for Repairing of broken edges of RCC chajjas, roof projections, fins, facia and similar works by dismantling of loose and damaged/ disintegrated portion of edges (cross sectional area not exceeding 150 sqcm) with cement mortar 1:4 or cement concrete 1:1½:3 type A0 and chicken wire mesh with nails (to hold fresh mortar/concrete) including necessary formwork etc. and scaffolding for work upto four storied buildings. Note : work to be executed for multistorey bldgs only.

Taking down AC rain water pipes(any size or pattern) including all fittings,head shoes,bends,swan neck etc. Note: work is to be executed at any height and situation.

S&F PVC (SWR) pipes110 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls including fixing clamp etc. Note: work is to be executed at any height and situation.

Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) orinsulation boards/slabs/blankets, any thickness, including cover fillets

S&F Gl frame work(size of grid 605 x 605 mm) for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

S&F 6mm thick PVC multiwall 250mm wide (tongue and groove interlocking type) panels, textured on one side (as approved): fixed to framework in ceiling with countersunk screws and inerlocked, including all necessary special fitting accessories such as junction, corner and turning matching to board complete.

S&F 8mm thick PVC multiwall 250mm wide (tongue and groove interlocking type) panels wall lining and fixing at site.

M&L for demolition of old RCC cover slab and providing new factory made RCC perforated cover slab grade designation LD2.5,clear opening of frame 450 x 900mm conforming to IS 12592:2002,thicknes 75mm and removing the debris out of MOD land.

M&L for removing SS poles of any description embedded in concrete, removing damaged concrete base and casting the same in PCC 1:2:4 type B-1 concrete of size 30cm X 30cm X 30cm, and erecting back in soil of any type including necessary excavation and making good disturbed ground complete all as specified and as directed.

Dismantling of MS /Aluminium glazed partition of any description including connected fittings.

S&F aluminium (50 micron powder coated) frame for doors,windows,ventilators and glazed partition frame of any size with one or more rebates including joining cleat,beading,glazing clips and connected accessories as required for fixing etc.complete all as specified. Note.work is to be executed for high rise bldgs.quoted rate deems to be inclusive of all connected accessories required to fix partition with glazing on floor/wall.

S&F aluminium (50 micron powder coated) door shutters,aluminium sections weighing 0.55kg/m including necessary joining cleats,glazing clips,rubber neoprene packing,handles 2 nos in each door shutter,hinges,anodised aluminium snap beading screws etc complete all as specified. Note.Work is to be executed for high rise bldgs.

M&L for 12mm thick Prelaminated particle board,exterior grade(BWP),prelaminated both sides with decorative choice lamination & fixed with screws to timber frame work/aluminium frame for doors/Partition over and including all fittings and fixtures complete all as specified and directed.

S&F 4.0mm thick sheet glass,ordinary quality and glazing with silicon gel in square n. exc 0.5 sqm in each pane. Note.work is to be executed at any height and situation.

Taking down MS door/ window/ventilators frames with shutters of any size and any description,making good soffits,jambs,cills etc to receive new window/ventilators frame complete all as specified and as directed. Note:work is to be executed for high rise bldgs.

Taking down carefully MS window shutters of any size and description,making good soffits,jambs,cills etc to receive new window/ventilators frame complete all as specified and as directed. Note:Work is to be executed for high rise bldgs and occupied qtrs on urgency basis,hinges shall also be cut as reqd to fit new window properly.contractors quoted rate deems to be inclusive of the said provision.

S&F aluminium (50 micron powder coated) window and ventilator shutters sliding type without sash bars,aluminium sections weighing 0.55kg/m including necessary joing cleats,glazing clips,rubber packing,anodised aluminium snap beading,screws,locking etc. Note.Work is to be executed for high rise bldgs.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average witdth of aperture 1.40mm and fixed with stainless steel wire staples. Note. Work is to be executed at any height and situation.

M&L for Raking out existing construction joints/dummy joints 10mm wide X 25mm deep in concrete pavements, cleaning surfaces and sweeping to make the surface free from dust/dirt with air compressor/blower and removing debris to a distance exceeding 200m from edge of pavement..

M&L for Raking out existing expansion joints 20mm wide X 25mm deep in concrete pavements, cleaning surfaces and sweeping to make the surface free from dust/dirt with air compressor/blower and reoving debris to a distance exceeding 200m from edge of pavement for disposal in low lying areas.

M&L for Filling construction joints/dummy joints 10mm wide X 25mm deep in concrete pavements with sealing compound Grade ‘B’ after applying primer to the sides of joints as per manufacturer's instructions.

M&L for Filling expansion joints 20mm wide X 25mm deep in concrete pavements with sealing compound Grade ‘B’ after applying primer to the sides and bottom of joints as per manufacturer's instructions.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 1,03,180.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

Abhiraj Enterprises (BID ID -3122930)

MANOVANDANA CONSTRUCTION (BID ID -3132752)

Ranmale Developers (BID ID -3130538)

J Sams Contructions (BID ID -3117952)

M/S SAMEER SUBHASH PATANI (BID ID -3124293)

Bidder Name

M/S SAMEER SUBHASH PATANI

J Sams Contructions

M/S R.K.S. CONSTRUCTION

Abhiraj Enterprises

MANOVANDANA CONSTRUCTION

Ranmale Developers