Loading
Loading…
Loading…
Tender Value
Refer Docs
EMD Value
₹3.5 L
Closing Date
5 May 2026, 10:30 pmClosed
Cauvery Neeravari Nigam Limited
Ashfaq Ahmed
Rehabilitation and improvements to Hydro Mechanical Components of Taraka Dam in Mysore District of Karnataka State under DRIP Phase-II (World Bank Aided) (Package-4)
CNNL/2024-25/GH/WORK_INDENT2127/CALL-4
CNNL/2024-25/GH/WORK_INDENT2127/CALL-4
Open
Gates/Hoists and Allied Works
Two Tender Document System(Two Cover)
CNNL KR Div Kabini Colony
8 documents required · 8 mandatory
A minimum number of one similar contracts (Installation of new gates such as Sluice Gates/ Crest Gates in any Dams) that have been satisfactorily and substantially completed as a prime contractor between 1st April 2019 and bid submission deadline (1) One contracts of similar work, of minimum value INR 2.81 crores (80% of estimated value) Or (2) TWO contracts, each of minimum value 2.11crores (60% of the Estimated Value) Or (3)THREE contracts, each of minimum value 1.40 crores (40% of the Estimated Value).
For the above contract (substantially completed and under implementation) as prime contractor, joint venture member, or sub contractor between 1st April 2019 and Application submission deadline, a minimum construction experience in the following key activities successfully completed in any one year of last 7 years, 1 Fabricating, supplying & erecting M.S.Angular Truss for all spans 77085.00 Kgs, 2. Design, fabrication, supply, erection, testing and commissioning of fixed wheel type vertical lift gate, 30.35 Tonne, 3.Design, fabrication, supply, erection and commissioning of trash racks -26.00 Tonne, 4.Design, fabrication, supply, erection and commissioning of structural steel hoist bridge consisting of columns, beams, bracings-20.80 Tonne, 5.Supply and fixing of cast steel new roller by removing old damaged-10 Tonne, 6.Design, fabrication, supply, erection and commissioning of embedded parts consisting of liners for trash rack grooves 5.50 Tonne should have been completed successfully in last 7 years.
Work done certificates issued by the officer not below the rank of Executive Engineer.
Experience under installation of new sluice gates, fixing of rollers, wire ropes, rubber seals to crest gates or sluice gates at dam works in the role of prime contractor, JV member, subcontractor for at least the last seven years starting 1st April 2019.
Construction equipment owned by the tenderer and equipment proposed to be deployed on this contract, if awarded. The Bidder must demonstrate that it will have access to the key Contractors equipment listed as per qualification criteria section 4. Equipment in the uploaded bid document.
List of Financial Resources with Certificates
The Bidder shall provide details of the Key Personnel and such other Key Personnel that the Bidder considers appropriate, together with their academic qualifications and work experience. The Bidder shall complete the relevant Forms in Section 4, Bidding Forms. The key personnel requirement is as per qualification criteria Section-3. key personnel.
Minimum average annual construction turnover of Rs.3.88 Crores (Three crore eighty eight lakhs) calculated as total certified payments received for contracts in progress and/or completed within the last seven financial years, divided by seven years.
GST Registration certificate
The Bidder shall demonstrate that it has access to, or has available, liquid assets, unencumbered real assets, lines of credit, and other financial means (independent of any contractual advance payment) sufficient to meet the construction cash flow requirements estimated as Rs. 0.8775 Crores about 3 months cash flow at peak construction period) for the subject contract(s) net of the Bidders other commitments.
Total value of civil engineering works executed and payments received in the last seven years (year-wise)
Banker Details for reference
Reports on the financial standing of the tenderer, such as profit and loss statements and auditors reports for the last seven years.
PWD class 2 & above Civil License registration copy
List of existing commitments and ongoing works
List of works for which tenders already submitted
₹5,000
₹3.5 L
22 Apr 2026
22 Apr 2026
6 May 2026
28 Apr 2026
27 Apr 2026
Package-4 Rehabilitation and improvements to Hydro Mechanical components of Taraka Dam in Mysore District of Karnataka state under DRIP-II(World Bank Aided)
Supply and fixing of cast steel new roller by removing old damaged roller, the roller should befitted with zkl/skf no.22 222 self alining double taper ball bearing, with oil seal, rubber owering greas...
Supplying and fixing Z- type rubber seals and hot dipped G.I bolts /nuts / washers of approved quality including cost of all materials, labour, removing existing worn out / damaged Z- type rubber seal...
Supplying and fixing flat rubber seals and hot dipped G.I bolts /nuts / washers of approved quality including cost of all materials, labour, removing existing worn out / damaged flat type rubber seals...
Providing and fixing new wire rope 6x36x32 mm constrained to vertical gates. Realising old wire rope and fixing new wire rope, including cutting, welding, grinding, lead and aligning wire rope both si...
Cleaning gates / hoists / embedded parts to expose fresh metal surface for repainting by sand blasting method as per specifications including cost of all materials, labour, machinery, scaffolding, app...
Providing and applying one coat of zinc rich epoxy primer paint ( zinc conten 85 % ) of approved quality 40 micron dry film thickness to gates / embedded parts / hoist components including cost of all...
Providing and applying two coats of cold applied coal tar epoxy paint of approved quality 100 micron dry film thickness each coat to embedded parts / gates / lifting beam etc., including cost of all m...
Inspecting, repairs, resetting and alignment of the crest gate embedded parts for smooth operation, including cost of materials replacement of worn-out materials, lubrication, cost of ...
Inspecting, repairs, resetting and alignment of the crest gate Horizontal Girder by check welding of flange to web connectin, Horizantal girder to T stiffeners of skin plate ...
Inspecting, repairs, resetting and alignment of the crest gate Skin plate assembly by checking the Skin plate to "T" verticals, Vertical and horizontal joints of skin plate from upst...
Inspecting, repairs, resetting and alignment of the Sill beam, SS plate cladding to MS section girder which embedded in the concrete, SS Plate cladding for wall plate piling and wall plate pitting and...
Providing and applying cardium compound of approved quality to wire ropes of hoists / gantry cranes as part of the annual maintenance including cost of all materials, machinery, lab...
Providing and filling / replacing gear oil of approved quality upto the required gauge level for Radicon Gear unit of hoists / gantry cranes including cost of all materials, machinery, labour etc., co...
Providing and applying grease of approved quality to gate and hoist components requiring greasing as part of the annual maintenance using grease gun wherever necessary including cost of all ...
Design, fabrication, supply, erection and commissioning of embedded parts consisting of sill beam, wheel tracks, seal seats, guide rails etc., with all accessories for vertical lift barrage gate inclu...
Design, fabrication, supply, erection, testing and commissioning of fixed wheel type vertical lift gate consisting of skin plate, vertical and horizontal girders, wheels, stiffeners, ...
Design, fabrication, supply, erection and commissioning of structural steel hoist bridge consisting of columns, beams, bracings, stiffeners, ties, chequered plate covering, hand railing, l...
Design, fabrication, supply, erection, testing and commissioning of adequate capacity rope drum hoist consisting of hoist platform, rope drums, shafts, pulleys, gear system, electric motor, e...
Fabricating, supplying & erecting M.S.Angular Truss for all spans as per approved designs and drawing. The entire truss is anchored suitably by using 4 Nos. of M.S. anchor bolts at each support, w...
Design, fabrication, supply, erection and commissioning of trash racks consisting of a number of panels of suitable height with vertical trash bars welded to structural steel frame at wider interval a...
Design, fabrication, supply, erection and commissioning of embedded parts consisting of liners for trash rack grooves ( for coarse and fine screens ) with all accessories for pump house in...
Providing and installing of pre painted Galvolume iron Trapezoidal profiled sheet of approved make 1060 mm width (1000 mm cover width), 28-30 mm crest height with crest distance of 200 mm c/c with 2 r...
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
Bid Document - 2127-Call-4.doc
Tender Document • 4.01 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .