Construction of Vocational Lab (One Floor) with Shed at PM Shri Kendriya Vidyalaya, Andrews Ganj, New Delhi

Providing and laying in position cement concrete of specified grade excluding the cost of centering and

shuttering - All work up to plinth level: 1:4:8 (1 cement : 4 coarse sand (zone-III) derived from natural

5 4.1.8 sources : 8 graded stone aggregate 40mm nominal size derived from natural sources) Cum 12.00 6,812.00 81,744.00

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse

sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived

6 4.10 from natural sources) Sqm 48.00 410.85 19,720.80

Providing and laying in position ready mixed or site batched design mix cement concrete of M25 grade

with minimum cement content of 300 kg/cum; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland cement, admixtures as per IS:9103; including

pumping of concrete to site, curing, carriage for all leads; but excluding the cost of centering, shuttering

7 4.20.1.4 and finishing as per direction of Engineer-in-charge. All works upto plinth level. Cum 38.00 9,439.05 3,58,683.90

8 5.9.1 Providing and fixing TMT bars Fe-500D (reinforcement for RCC work including cutting, bending, binding) Kg 3,800.00 74.50 2,83,100.00

Providing and laying in position cement concrete - All work up to plinth level: 1:2:4 (1 cement : 2 coarse

sand (zone-III) derived from natural sources : 4 graded stone aggregate 40mm nominal size derived from

9 4.1.4 natural sources) for levelling course under RCC slab / roof. Cum 4.80 7,780.30 37,345.44

Sub-Total (B) - Concrete Work 7,80,594.14

Digitally signed by AMIT

S.No. DSR Item No. Description of Item Unit Quantity Rate (INR) Amount (INR)

C. MASONRY WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and

10 6.1.1 plinth in cement mortar 1:4 (1 cement : 4 coarse sand) Cum 18.00 7,370.65 1,32,671.70

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure

above plinth level up to floor V level in all shapes and sizes in cement mortar 1:4 (1 cement : 4 coarse

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

12 6.13.2 superstructure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand) Sqm 48.00 1,123.80 53,942.40

Sub-Total (C) - Masonry Work 4,48,255.90

D. PLASTERING & POINTING

13 13.1.1 12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand) on walls (internal) Sqm 280.00 347.05 97,174.00

15 mm cement plaster on rough side of single or half brick wall of mix 1:6 (1 cement: 6 coarse sand)

12 mm cement plaster finished with a floating coat of neat cement of mix 1:3 (1 cement: 3 fine sand) on

15 13.7.1 ceiling (RCC slab soffit) Sqm 80.00 439.25 35,140.00

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and

16 13.80 manufacturer, over the plastered wall surface to prepare the surface even and smooth complete Sqm 360.00 156.05 56,178.00

Sub-Total (D) - Plastering & Pointing 2,59,655.00

E. FLOORING & DADO

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer,

in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with

grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments

etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the

notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the

tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size 600 x 600 mm. [Heavy duty anti-

skid finish suitable for vocational lab - non-glossy surface for safety against slipping, load bearing for lab

17 11.41A.3.1 equipment/machinery] Sqm 80.00 1,464.85 1,17,188.00

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer) with

water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours & shade,

in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) jointing

with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments

etc. complete. Size of Tile 600x600 mm. [Skirting height minimum 150mm in all lab areas as per lab

18 11.46.2 safety norms; anti-skid matt finish to match floor tiles] Sqm 45.00 1,623.05 73,037.25

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a

floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc.

19 11.3.1 complete. 40 mm thick with 20 mm nominal size stone aggregate Sqm 18.00 614.20 11,055.60

Digitally signed by AMIT

S.No. DSR Item No. Description of Item Unit Quantity Rate (INR) Amount (INR)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the

manufacturer) of 1st quality conforming to IS: 15622 of approved make in colours such as White, Ivory,

Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), Jointing with

grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment

Sub-Total (E) - Flooring & Dado 2,12,246.35

F. DOORS, WINDOWS & FIXTURES

Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part I) non-decorative type,

core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick

21 9.21.1 including ISI marked Stainless Steel butt hinges with necessary screws Sqm 16.80 2,392.65 40,196.52

Providing and fixing powder coated aluminium (min 50 micron) sliding windows with extruded built up

standard tubular sections conforming to IS:733 and IS:1285, complete with 5mm float glass glazing,

EPDM rubber/neoprene gasket and all fittings (Composite: aluminium sections @5.5 kg/sqm as per

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked

together through their entire length and jointed together at the end by end locks, mounted on specially

designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push

and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire

springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1

and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed

and fixed in position with hold fast lugs or with dash fasteners of required dia & length. Sal wood (DSR

24 9.1.2 rate Rs 116,520.30/cum; derived for 100x75mm section @ 0.0075 cum/Rmt = Rs 873.90/Rmt) Rmt 48.00 873.90 41,947.20

25 10.33.1 Providing and fixing SS hardware (tower bolts, handles, hinges, aldrops etc.) Per Door 6.00 2,850.00 17,100.00

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer using structural steel etc. as required. In gratings,

26 10.25.2 frames, guard bar, ladder, railings, brackets, gates and similar works Kg 350.00 172.60 60,410.00

Sub-Total (F) - Doors, Windows & Fixtures 2,90,834.42

Applying priming coats with primer of approved brand and manufacture, having low VOC content - with

27 13.85.3 water thinnable cement primer on wall surface having VOC content less than 50 grams/litre Sqm 360.00 73.95 26,622.00

Wall painting with premium acrylic emulsion paint of interior grade, having VOC content less than 50

grams/litre of approved brand and manufacture, including applying additional coats wherever required to

28 13.83.2 achieve even shade and colour - Two coats Sqm 360.00 142.80 51,408.00

Digitally signed by AMIT

S.No. DSR Item No. Description of Item Unit Quantity Rate (INR) Amount (INR)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade - Two or

29 13.61.1 more coats on new work (on wood and metal surfaces - doors, windows, grills) Sqm 80.00 155.90 12,472.00

Finishing walls with Acrylic Smooth exterior paint of required shade - New work (Two or more coat applied

30 13.46.1 @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) Sqm 180.00 160.60 28,908.00

Sub-Total (G) - Painting 1,19,410.00

H. STEEL STRUCTURAL WORK (SHED - 8.0m x 6.0m)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including

31 10.2 cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete Kg 1,800.00 133.70 2,40,660.00

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as

approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm

thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in

240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18

microns, fixed using self drilling/self tapping screws with EPDM seal, complete upto any pitch, excluding

32 12.50 the cost of purlins, rafters and trusses and including cutting to size and shape wherever required Sqm 110.00 738.65 81,251.50

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50

mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc

coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side

of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete. Ridges

Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets

40x3 mm size, bolts, nuts and washers etc., including making necessary connections with rain water

34 12.7.2 pipes complete. 0.63 mm thick with zinc coating not less than 275 gm/m2 Rmt 20.00 944.05 18,881.00

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type

A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion.

35 12.41.2 Single socketed pipes. 110 mm diameter Rmt 12.00 377.40 4,528.80

PCC 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm) for shed foundation/column

Design mix cement concrete M25 grade (min. cement 300 kg/cum) for shed column/foundation - as per

37 4.20.1.4 item 4.20.1.4 (excl. centering & reinforcement) Cum 4.80 9,439.05 45,307.44

38 5.9.1 TMT reinforcement Fe-500D for shed foundation Kg 480.00 74.50 35,760.00

Sub-Total (H) - Steel Structural Work (Shed) 4,93,499.94

I. WATER SUPPLY & SANITARY FITTINGS

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10

litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm

flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of

39 17.3.1 approved municipal design complete - W.C. pan with ISI marked white solid plastic seat and lid Set 2.00 8,006.60 16,013.20

Digitally signed by AMIT

S.No. DSR Item No. Description of Item Unit Quantity Rate (INR) Amount (INR)

Providing and fixing white vitreous china wash basin size 550x400 mm with C.I. brackets, pair of 15 mm

C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and

40 17.7.3+17.8 brackets, complete (17.7.3) with white vitreous china pedestal completely recessed (17.8) Set 3.00 3,985.10 11,955.30

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and

stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls -

41 17.10.2.2 Kitchen sink without drain board 610x460 mm bowl depth 200 mm Nos 2.00 3,873.80 7,747.60

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold

water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m

spacing, jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases

and making good the same including testing of joints complete - Concealed work, 25 mm nominal dia

43 MR Providing PVC SWR pipes 110mm dia with fittings for drainage Rmt 30.00 350.00 10,500.00

44 MR Providing floor trap (nahni trap) 110mm CP jali with PVC body Nos 4.00 650.00 2,600.00

45 MR Providing and constructing inspection chamber 450x450mm inside Nos 2.00 2,500.00 5,000.00

Sub-Total (I) - Water Supply & Sanitary 82,042.35

J. ELECTRICAL WORK

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC

insulated copper conductor single core cable in surface/ recessed steel conduit, with modular switch,

modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper

46 1.3.2 conductor single core cable etc. as required. Group B Point 24.00 1,684.00 40,416.00

Wiring for 5/6A socket point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core

cable in surface/ recessed steel conduit, with modular socket, modular plate, suitable GI box and earthing

the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.

Wiring for 15/16A power point with 2X4 sq.mm FRLS/HFFR PVC insulated copper conductor single core

cable in surface/ recessed steel conduit along with 1 No. 4 sq.mm FRLS PVC insulated copper conductor

single core cable for loop earthing as required (DSR E&M 2025 Item 1.5 @ Rs 480/Meter; derived per

48 1.5 (derived) point basis for avg 5m cable run) Point 12.00 2,400.00 28,800.00

Supplying, installation, Testing & Commissioning of LED surface mounted Batten light, 18-22 Watt, body

material and construction as per IS:10322 with driver (Replaceable) as per the requirement with Driver

efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, THD <10%, P.F.>=0.95, IP20,

CRI >=80, UGR <=19, Flicker free, life time 50000 Burning Hours, System lumen efficacy >=105 <120

49 8.9.1 lm/Watt. Powder coated die cast /Extruded aluminium Body (Thickness >=1.20 mm) Nos 24.00 681.00 16,344.00

Digitally signed by AMIT

S.No. DSR Item No. Description of Item Unit Quantity Rate (INR) Amount (INR)

Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., body material and construction as

per IS:10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-

270 Volt, frequency 50/60 hz, THD <10%, P.F.>=0.95, IP20, CRI >=80, UGR <=19, Flicker free, life time

50000 Burning Hours, System lumen efficacy >=105 <120 lm/Watt. 40 watt, Powder coated die cast

50 8.6.5 /Extruded aluminium Body (Thickness >=1.20 mm) Nos 8.00 2,681.00 21,448.00

Installation, Testing and Commissioning of ceiling fan, including wiring the down rods of standard length

(upto 30 cm) with 1.5 sq. mm FRLS/HFFR PVC insulated, copper conductor, single core cable etc. as

Supply of ceiling fan 1200mm sweep, BEE 5 star rated, aluminium blade, double ball bearing, with

52 MR electronic regulator ( Nos 8.00 3,000.00 24,000.00

Installation, Testing and Commissioning of exhaust fan upto 450 mm sweep in existing opening, including

1.50.1+1.51 making good the damage, connection, testing, commissioning etc. Extra for fixing louvers/shutters

53 complete with frame for exhaust fan. [DSR 1.50.1 @ Rs 556 + DSR 1.51 @ Rs 260] Each 4.00 816.00 3,264.00

54 MR Supply of exhaust fan 300mm sweep with metal body, bird guard Nos 4.00 2,000.00 8,000.00

Supplying and fixing 12 way, Double door, single pole and neutral, sheet steel, MCB distribution board,

240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,

55 2.3.3 interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) Nos 2.00 2,871.00 5,742.00

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current

circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with

56 2.15.3 connections, testing and commissioning etc. as required. 63 A Nos 2.00 3,597.00 7,194.00

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for

inductive load of following poles in the existing MCB DB complete with connections, testing and

57 2.10.1 commissioning etc. as required. Single pole Nos 12.00 285.00 3,420.00

Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry

enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and

Supplying and laying 4 core x 10 sq mm XLPE insulated PVC sheathed copper armoured cable (1.1 KV

grade) from main panel to distribution board through 63mm DWC HDPE pipe laid direct in ground (75cm

below GL) including end termination. [Composite: DWC pipe DSR 15.16.1 @ Rs 289/m + Cable laying

15.16.1+10.5.1+ DSR 10.5.1 @ Rs 47/m + Termination DSR 11.1.32 @ Rs 325/each x 2 ends prorated + Supply of 4c x

59 11.1.32+MR 10 sq mm copper armoured cable MR @ Rs 1,415/m (incl GST)] Rmt 30.00 1,773.00 53,190.00

Digitally signed by AMIT

S.No. DSR Item No. Description of Item Unit Quantity Rate (INR) Amount (INR)

Supplying, drawing, installation, testing and commissioning of CAT6 UTP LSZH 23AWG copper LAN

point for digital board complete with CAT6 I/O with face plate and 3m patch cord, including laying through

63mm DWC HDPE pipe underground. [Composite: CAT6 UTP cable 1 run DSR 39.17.1 @ Rs 60/m x

20m = Rs 1,200 + CAT6 I/O with face plate DSR 39.14 @ Rs 212 x 1 = Rs 212 + CAT6 Patch cord 3m

39.17.1+39.14+3 DSR 39.12.2 @ Rs 227 x 1 = Rs 227 + 63mm DWC HDPE pipe underground DSR 15.16.1 @ Rs 289/m

Supplying, Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioner

(Inverter Type - Cooling only) complete with IDU, ODU, surface/concealed copper refrigerant piping with

insulation upto 3 Mtr, copper power cable upto 3.5 Mtr, drain pipe, R-32/R-410/R-407 Green Refrigerant,

wireless remote control, 180-260V, 1 phase, Scroll/rotary compressor, 5 Star BEE Rating. 2.0 TR. Min 5

61 32.2.4 year OEM warranty. As per CPWD specification and IS:1391 Part II 2023. Nos 2.00 57,396.00 1,14,792.00

Sub-Total (J) - Electrical Work 3,95,670.00

K. MISCELLANEOUS

60 MR Providing and fixing laboratory work bench (granite top, 2400x750x850mm) with storage underneath Nos 4.00 45,000.00 1,80,000.00

61 MR Providing and fixing laboratory stools (revolving, height adjustable, SS frame) Nos 30.00 4,000.00 1,20,000.00

62 MR Providing and fixing wall-mounted display board (1200x900mm felt/whiteboard) Nos 2.00 4,500.00 9,000.00

Providing, installing and commissioning 75 inch (190 cm) Interactive Flat Panel Display / Digital Smart

Board (4K UHD, 20-point multi-touch, Android OS built-in, dual speakers, HDMI/USB-C/Wi-Fi, anti-glare

63 MR tempered glass, wall mount bracket, OPS slot) of approved make Nos 1.00 1,85,000.00 1,85,000.00

64 MR Providing and fixing storage cupboard (steel, 900x450x1800mm) for equipment/tools Nos 4.00 18,000.00 72,000.00

65 MR Providing fire extinguisher (ABC type, 4 kg) ISI marked with wall bracket Nos 2.00 2,800.00 5,600.00

66 MR Providing name board / signage for Vocational Lab (acrylic backlit) Nos 1.00 8,500.00 8,500.00

67 MR Providing and fixing Surge Protection Device (SPD) Type-2 in distribution board Nos 2.00 2,000.00 4,000.00

Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate

68 17.16A to European type W.C. of quality and make as approved by Engineer-in-charge Nos 2.00 2,000.00 4,000.00

Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the

69 17.22A direction of Engineer-in-charge Nos 3.00 2,200.00 6,600.00

70 MR Providing and fixing emergency eye wash station (wall mounted, SS) with plumbing Nos 1.00 9,000.00 9,000.00

Sub-Total (K) - Miscellaneous 6,03,700.00

TOTAL - CIVIL WORKS (A to I) 28,02,992.10

TOTAL - ELECTRICAL & MECHANICAL WORKS (J) 3,95,670.00

TOTAL - MISCELLANEOUS / FURNITURE / ADDITIONS (K) 6,03,700.00

GRAND TOTAL - VOCATIONAL LAB 38,02,362.10

GRAND TOTAL - VOCATIONAL LAB 38,02,362.10

Digitally signed by AMIT