GE/CHM-98/2024-2025 SPL REPAIR OF ROOF TREATMENT AND SEEPAGE IN OFFR MESS, SINGLE OFFR ACCN, REGT MANDIR AND PROVN OF 03 UNRINAL BLOCK UNDER AGE B/R II AT CHANDIMANDIR

Amount

Dismantling of existing brick tiles or terracing tiles single layer on roof grouted in cement mortar, demolition of mud phuska of any thickness including removal of rubbish from site complete all as specified & directed.

PCC 1:2:4 type B-0 (using 20m graded crushed stone aggregate) as in roof padding, finished fair and even without using extra cement, complete all as specified and directed.

Rendering 15mm thick in Cement and Sand mortar 1:4 over fair faces of brick / concrete ,finished even and smooth without using extra cement, including using water proofing compound complete all as specified. Note : WPC shall be measured and paid separately.

Supply only integral water proofing compound (ISI Marked) complete all as specified & directed.

3mm thick Atactic polypropylene polymer (APP) based polymeric membrane minimum weighing 3.6kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gm/sqm) laid over a coat of bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS, over primer coat bonding material of blown bitumen 85/25 grade heated to working temperature of 180° C applied @1.2Kg/Sqm. The membrane shall be laid using butane torch and sealing all joints etc after preparing the surface as per standard practice and as per manufacturer instructions including dismantling of existing felt /treatment, complete all as specified & directed.

40mm thick brick tiles (laid on and including 15mm thick screed bed in cement mortar 1: 6) ,joints grouted flush in cement mortar (1 : 3) mixed with 5% of crude oil by weight of cement, complete all as specified and as directed.

All as per serial item No 6 herein before but except tiles –ditto-

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed

Demolition of stone slabs and tiles of any description or thickness in floors laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of plain cement concrete in ground floor and paving n.exc 15cm thickness below or above ground level complete all as specified and directed.

Demolition of cement concreteof any description and in any position complete all as specified and directed.

Reinforced cement concrete, 1:1½:3 (nominal mix,type A-1, using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams etc, shelves and the like complete, all as specified and directed .

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm complete all as specified and directed.

TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified & directed.

Non skid, first quality ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area or each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 15mm thick rendering in cement mortar 1:4 complete all as specified and directed.

25mm thick Plain cement concrete 1:2:4 type B-0 using 12.5mm graded aggregate as in sub base complete all as specified & directed.

Glazed coloured ceramic tiles in vertical surface 450mm x 300mm x 7mm thick thick , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

16-18mm thick Granite work (of any type table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in, set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite compelte all as specified and directed.

Rounding of / moulding to edges of stone of any description including rubbing and polishing (Granite finish) complete all as specified and directed.

Coloured vitrified ceramic tiles, light shade, 8-10mm thick (square/rectangular) , area of each tiles exc 0.42 sqm but n.exc 1 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

All as per serial item No 21 herein before but on skirting etc over and including 10mm thick rendering in cement mortar 1:4

75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed.

100mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed.

providing cement concrete type D2, 1:4:8 using 40 mm graded stone aggregate, as in foundation, mass concrete etc., complete all as specified and as directed

Plain cement concrete type B-1, 1:2:4 using (20 mm graded crushed stone aggregate) as in roof kerb, or mud stios, rounded or chamfered on edges, lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including the use of forms or moulds with plain faces complete all as specified and directed.

Hard core of gauge of broken stone or boulders, not exc 63mm , deposited spread and lavelled in layers n.exc 15 cm thick, watered & rammed to a true surface ,complete all as specified.

Coloured non skid porcelain tiles exterior grade 300x300x15mm thick heavy duty (Endura from Johnson or equivalent) as in floor, set and jointed in neat slurry and pointed in coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in cement mortar 1:6, complete all as specified and directed by Engineer-in-charge.

Plain cement mortar 1:3:6 (type C-2 using 40mm graded aggregate), 75mm thick as in Plinth protection , finishing cement concrete even and smooth without using extra cement, all as specified.

Demolition of brick masonry and built in cement mortar including all quoins arches, pillars complete all as specified & directed

Brick work with sub class ‘B’ bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

Concrete interlocking pre polished paver block, with grey cement and pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over and including 25mm thick sand cushioning, including dismantling of old tile complete all as specified and directed

Brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified & directed.

Taking down existing plaster of any description on brick wall/ concrete surface including racking out joints, hacking for key, scrubbing down with water etc complete, all as specified and directed.

15mm thick rendering cement plaster in Cement and Sand mortar 1:6 over brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

Rendering 15mm thick on fair faces of brick work surfaces, finished even and fair in cement mortar (1:4), complete all as specified.

10mm thick rendering in Cement and Sand mortar 1:3 on ceiling, surfaces finished even and smooth without using extra cement, complete all as specified and directed.

Precast reinforeced cement concrete type B-1, 1:2:4 using (20 mm graded crushed stone aggregate) for cover slabs (for man holes etc.) c setting in cement mortar 1:6 including necessary form work complete all as specified and directed. (Reinforcement shall be measured and paid separately).

Preparation of new plastered surfaces of walls and applying two coats of cement base paint of approved tint, complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over and including a coat of primer complete all as specified and directed.

Three coats of white wash on ceiling surfaces including preparation of new plastered surfaces complete all as specified and directed

Preparation of new surfacs and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

Complete removal of existing treatment of any type / descriptin viz distemper, white wash etc from plastered / un plastered surface of wall, chajjas, facia, cantilivers, RCC etc with mechanical means / grinder completely and applying two coats of oil bound distemper over and including one coat of interior wall primer including interior grade wall care putty (thickness vary from 1.5 to 2.5mm as required for desired smoothness and leveling of surfaces in two or more layers) and sand papering, making the surfaces even and smooth complete all as specified and directed.

Preparation of old plastered or unplastered surfaces of walls by completely removing existing treatment and applying two coats of exterior acrylic emulsion paint complete all as specified and directed.

One coat of white wash on ceiling surfaces including preparation of old surfaces complete all as specified and directed.

Preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Applying one coat of synthetic enameled paint on steel and iron surfaces over 10 cm width or girth including preparation of old surfaces complete all as specified & directed.

Dismantling of wall and ceiling board (fibre, pulp insulation etc) any thickness including cover fillet & removing from site complete all as specified and directed

Dismantling of asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed.

Powder coated Gl frame work for ceiling (Size of grid 605 x 605mm )comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm, fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long, including taking down old existing snap grid frame work complete all as specified and directed

4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws, complete all as specified.

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Taking down chowkats or frame n. exc. 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frame exc. 1.5 sqm and n exc 4 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutter of any description exc 1 Sqm but n.exc 2 Sqm each complete all as specified and directed.

Factory made pressed steel frames having profile 105mm x 60mm for doors with one or more rebates made out/fabricated of 1.25 mm thick MS sheet, including necessary fixing lugs, hinges, lock strike plate, thress hold bar/flat etc. including filling PCC 1:3:6 complete all as specified & directed.

Factory made pressed steel frames having profile 125mm x 60mm for doors with one or more rebates made out/fabricated of 1.25 mm thick MS sheet, including necessary fixing lugs, hinges, lock strike plate, thress hold bar/flat etc. including filling PCC 1:3:6 complete all as specified & directed.

35mm thick flush shutters, solid core costruction, with block board core and plywood face panels, commercial type on both sides as in cupboards, etc. complete all as specified and directed.

Glazed and gauged skelton shutter (Factory made) 35mm thick of second class hard wood open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc including priming coat. Size of members of shutters as specified in SSR Part I Section 8, clause 8.20 (a) including Kiln seasoned and chemically pressure treated,complete all as specified & directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type moulded door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge

Steel window, box type, primer coated, 1.00mm wall thickness, with glazing bar and openable shutter prepared to recieve sheet glass, complete including cutting holes, four Nos. for each window and making good dismantled portion in PCC (1:2:4) type B-1. including following fittings welded to frame/ shutter complete all as specified and directed.:- (a) Hold fast 150mm out of 25x6mm flat iron made to shape- 04 Nos. each window (02Nos. on each side). (b) Handle of 'Z' section 20mmx25mm, 100mm long- 01No. each leaf. (c) MS tower bolt 150mm long- 02 Nos. each leaf. (d) 'Z' section 20mmx25mm, 100mm long stopper 01 No. each leaf. (e) Cleat 55mm long of hollow square section 15mmx15mm of 24 guage wall thickness, welded to hinge of 55mm size 01 No. per leaf. (f) MS box type hinges of 75 mm size- 02Nos. per leaf. (g) Fabrication & fixing complete. Note: Glass panes & painting shall be measured & paid separately under respective item.s. Design shall be approved from Engr-in-Charge as existing at site and all as per Drawing before fabrication and bulk order to the manufacturer.

All as per serial item No 63 hereinbefore but without glazing bar.

Factory made box type steel ventilators, with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as specified and directed.

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0, all as specified and directed.

Rolled sections as in main and cross beams, hip and jack rafters,purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates, conforming to Fe-290 Gde E165, all as specified and directed.

Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples , complete all as specified and directed.

4mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

4mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panesas complete all as specified and directed.

Butt hinges 100mm size, of extruded aluminum alloy with galvanised mild steel hinge pin, anodised, type C-21, complete all as specified and directed.

200 mm size aluminium , barrel tower bolt of extruded section and fixed complete all as specified and directed.

150 mm size aluminium , barrel tower bolt of extruded section and fixed complete all as specified and directed.

150 mm aluminium handles cast type anodized complete all as specified and directed.

300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed,complete all as specified and directed.

300mm long mild steel helical door springs including roller and roller plate fixed to angle iron door frame including welding etc, complete all as specified and directed.

Floor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring, fixed in floor (140mm size), complete all as specified and directed.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators, three track sliding window chowkhat section and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

Powder coated aluminium sections as in frames/ shutter of doors/window/ventilators /partitions, (Sliding / openable/ three track) including joinging cleats, glazing clips, rubber neoprene beading, powder coated aluminim snap beading, screws etc. fixed as in repair complete all as specified and directed Note : (i) Minimum thickness of power coating shall not be less than 50 micron. (ii) Weight of aluminum section only shall be measuerd and paid. (iii) Aluminum doors/windows /ventilators to be fixed to jambs with chromium plated screws . (iv) The rate shall be inclusive of neoprene beadings, snap beading, screws etc and in case of sliding shutters locking arrangement and rollers in sliding shutters. Weight of fitting fixtures will not be measured for arriving the weight of aluminum section. (v) Glass /wooden panel/ACP sheet shall be measured and paid separately under respective items. (vi) Design as directed by Engineer in charge.

5.00mm thick ordinary quality tinted glass, fixed to aluminum frame work in panels n.exc 0.5 Sqm in each pane, complete all as specified & directed.

5.00mm thick ordinary quality tinted glass, fixed to aluminum frame work in panels exc 0.5 Sqm in each pane, complete all as specified & directed.

9mm thick pre laminated particle board (ISI Marked), interior grade, pre laminated one side with decorative choice lamination and other side balancing white lamination fixed with screw to timber /aluminium frame work complete all as specified and directed.

Mortice lock, verticle type, mild steel, 4 levers, size 100mm, brass body, complete all as specified and directed

Door closer hydraulically regulated aluminum (die cast) body, designation No 3, universal type, suitable for door shutters of 701mm to 850mm in width and of weight between 36 to 60 Kg, fixed as in repair complete all as specified and directed.

25mm dia stainless steel curtain rod including fixing fancy types brackets, stops, rollers etc., as in repairs complete all as specified and directed.

Factory made 18mm thick solid WPC (Wood Polymer Composite) board of density 650 Kg /cum of one side prelaminated / rigidlam with any colour and other side balancing laminate as in cup board/ kitchen cabinet shutter/ drawer, front shuters, fixed with screws, solvent / adhesive, fixed as in repair complete all as specified and directed.

20mm wide and 1mm thick PVC edge bending of PVC pasted on edges with suitable adhesive, complete all as specified and directed.

Magnetic catcher cum silencer CP and fixed with standard steel screws, complete all as specified and directed.

Stainless steel handles, fancy type(ISI Marked), 150mm long , compelte all as specified.

Supply only of soft auto closing hinges openable at 0 degree for kitchen cabinet shutters Make :Hettich/ Ebco/ Primer

PVC (SWR) pipe, 75mm bore, single socketed in any length with rubber ring joints, fixed to walls or laid in floor, fixed as in repair complete all as specified and directed.

PVC (SWR) pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls or laid in floor, fixed as in repair complete all as specified and directed.

PVC (SWR) pipe, 75mm bore, single socketed in any length with rubber ring joints, fixed to walls or laid in floor, complete all as specified and directed.

PVC (SWR) pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls or laid in floor, complete all as specified and directed.

75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm bore, including jointing to waste pipe set in cement concrete type B-1(1:2:4) , fixed as in repair complete all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 100mm bore, including jointing to waste pipe set in cement concrete type B-1(1:2:4) , complete all as specified.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Vitreous china wash hand basin, white, angle back size 550 x 400 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, 32mm bore brass CP waste fitting, PVC Connection, cutting for and pinning in ends of bracket or erecting stand, fixed as in repair complete all as specified and directed.

Vitreous china wash hand basin, white, angle back size 550 x 400 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, 32mm bore brass CP waste fitting, PVC Connection, cutting for and pinning in ends of bracket or erecting stand, complete all as specified and directed.

Vitreous China Wash down water closet (pedestal pattern) , white, (excluding, flushing cistern and flush pipe) with and including PVC seat cover, fixed as in repair complete all as specified and directed.

Vitreous China Wash down water closet (pedestal pattern) , white, (excluding, flushing cistern and flush pipe) with and including PVC seat cover, complete all as specified and directed.

PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC long bend, set with concrete and making good to floor, fixed in repair complete all as specified & directed.

PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC long bend, set with concrete and making good to floor, complete all as specified & directed.

32mm dia waste coupling / waste fitting of PTMT any colour high-pressure screwed for iron pipe and fixed (minimum weight 45 gms), complete all as specified and directed.

Stainless steel soap dish any type, fixed to plugs with screw complete all as specified and directed.

Brass chromium plated bottle traps 40mm bore for wash basins, minimum water seal 25mm, with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed.

Single lever extended basin mixer, without Popup waste and 450mm Long Braided Hoses, cast copper alloy, cast copper alloy chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed. Make : Jaquar FUS-29023B or equivalent as approved in Appx 'C'

Single lever 3-inlet divertor exposed parts kit consisting of operating lever, cartridge sleeve, wall flange (with seals) button assembly, sleeve and button cap (compatible with ALD-193N), suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed. Make : Jaquar KUP-35193NKPM or equivalent as approved in Appx 'C'

Concealed body 3-inlet single lever diverter with button assembly but without expsoed parts suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed. Make : Jaquar ALD-193N or equivalent as approved in Appx 'C'

Bathtub spout with wall flange suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed. Make : Jaquar SPG-429PM or equivalent as approved in Appx 'C'

Bib taps brass, fancy type, long body with wall flange, standard chromium plated, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed.

Bib taps brass, fancy type, long body with wall flange, standard chromium plated, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, complete all as specified and directed.

Chromium plated shower rose 125 mm size and 15mm dia with or without swivel joints including fixing to pipe and union, fixed as in repair complete all as specified and directed

450mm long Braided Hose with two 15mm nuts, washers , without nipple(suitable for geysers), pipe nozzle fixed as in repairs complete all as specified and directed.

Cast copper alloy, chromium plated towel rail 600mm long, fixed as in repair, complete all as specified and directed.

Cast copper alloy, chromium plated towel rail 600mm long, complete all as specified and directed.

Cast copper alloy, chromium plated towel ring, fixed as in repair, complete all as specified and directed.

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe,complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 20mm bore pipe, fixed complete all as specified and directed.

Health faucet brass chromium plated (health faucet with 01 m pipe & wall hook) for 15mm bore with fittings, fixed as in repair complete all as specified and directed.

Vitreous China half stall urinal, fixed against wall in cement mortar (1:2), securing urinal with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm PVC waste pipe, complete all as specified and directed.

15mm bore brass CP urinal valve auto closing ssytem(push cock) with built in control & wall flange complete all as specified and directed.

25 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors includng taking down old existing pipe complete all as specified and directed.

20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors ncludng taking down old existing pipe complete all as specified and directed.

15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors ,ncludng taking down old existing pipe complete all as specified and directed.

20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors ,complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc and cutting chases for concealed water tubing & making good, cutting not exc 10 cm girth, in brick walls complete all as specified and directed.

20mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repairs,complete all as specified and directed.

25mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repairs,complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repair, cleaning works etc and hoisting if required reconnecting and refixing in position of capacity exc 500 ltrs but n.exc 1000 ltrs, complete all as specified & directed.

Supply and fix 500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) triple layered, screwable lid, hoisted and fixed in position, including tank nipple, PTMT 20mm bore etc, icomplete all as specified

Supply and fix 1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) triple layered, screwable lid, hoisted and fixed in position, including tank nipple, PTMT 20mm bore etc, including dismantling of existing water tank complete all as specified

Surface excavation not exceeding 30 cms deep and averaging 15cms deep and getting out in any type of soil, complete all as specified.

Excavation in post holes (or similar hole) each in hard & dense soil n.exc 0.50 cu m getting out, returning, filling and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm, complete all as specified and directed.

Taking down carefully aluminum/copper point wiring on & including hard wood battens, surface conduit and board/blocks etc or through conduits for light , socket or power point ,fan point complete incl fitting such as switches ,sockets, ceiling rose , holder socket, light fitting, regulators and making good disturbed surfaces of wall, floor , ceiling etc and removing materials (other than those for which credit has been given by the contractor) to the MES stores yard for keeping in safe custody complete

Material and labour for point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit terminated on and including new modular sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed.

All as per serial item 144 herein before but for socket outlet 3 pin 5 Amps on same board complete all as specified and directed

All as per serial item 144 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed

All as per serial item 144 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor

Point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit terminated on and including new steel sunken boxes 1.2mm thickness covered with provision of 3mm thick plastic laminated sheet, comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note :Unit rate is inclusive of cutting chases in wall /foor/PCC and making good the disturbed surfaces to match the original finishes surface and nothing extra shall be paid on this account.

All as per serial item 148 herein before but for socket outlet 3 pin 6Amps on same board complete all as specified and directed

All as per serial item 148 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed

Switch modular type (ISI marked), single pole, one way 6 Amps, one module (ISI marked), complete all as specified & directed.

Switch modular type (ISI marked), single pole, one way 16 Amps, one module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2/3 pin 6 Amp modular type multi purpose two module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2 in 1 pin 6/16 Amp modular type multi purpose combined 2 module (ISI marked), complete all as specified & directed.

Switch piano, flush type, 6 amps, 230 volts, single pole, one way (ISI marked) complete all as directed by Engineer-in-charge

Sockets outlet multipurpose 2 in 1 pin, 6 and 6 Amps flush type ISI marked all as specified and directed by Engineer-in-charge

Modular switch type stepped fan regulator, single pole, 230 volt two module complete all as specified and directed.

Modular switch type bell push, single pole, 230 volt one module,(ISI marked) complete all as specified and directed.

Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.

Electric Bell, ding dong, AC, 230 volts, single pole all as specified and directed by Engineer-in-charge.

Lamp holder, PVC/Polycarbonate type with back plate modular type fixed on wall suitable for batten fitting ,complete all as specified and directed.

LED lamp 9 watts, B-22 type complete all as specified .

Disconnecting the power supply and taking down carefully by unscrewing from boards fittings and fixtures such as DBs, Junction Box, Panels of any size complete with all MCCB's ,MCB's etc and removing from site, Complete all as specified and directed .

MCCB, 125 Amps, four pole, 3 phase , 16KA, 415 volt with adjustable thermal and maganetic release, with proper thimble complete all as specified and directed

Vertical TPN distribution board double door flush mounting with provisions for MCCBs incomer upto 100 to 125 Amps & outgoing 4 way having IP 43 protection Complete all as specified and directed .

MCB DB, IP 43 protection, powder coated single door with locking arrangement suitable for surface and flush mounting, 02 way SPN with 200 Amps busbar 240V completed all as specified and directed.

MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 8 way SPN with 200 Amps busbar 240V completed all as specified and directed.

MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 12 way SPN with 200 Amps busbar 240V completed all as specified and directed.

MCB, SPN, 240 volt, 32 Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

MCB, SP, 240 volt, 40 to 63Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

MCB ,SP, 240 volt, 6 Amps to 32 Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size fixed as in repair complete all as specified and directed.

Slim LED lights fitting, 4 feet, 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose fixed as in repair complete all as specified and directed.

Slim LED lights fitting, 4 feet, 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Slim LED lights fitting, 2 feet, 1x 10W, inverter rechargeable, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose fixed as in repair complete all as specified and directed.

Taking down carefully old copper or aluminium sub main wiring of any Nos of wiring and size with earth wire on wooden batten/ surface conduit/ casing- capping complete with its all accessories and making good disturbed surfaces of wall , floors etc complete all as specified and directed.

Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 4 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 4 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 4 sqmm and one single core earth cable of 4 sqmm cable shall be considered as 1 running metre. (ii) colour code shall be Red for phase, Black for neutral and green for earth

Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 6 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 6 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 6 sqmm and one single core earth cable of 6 sqmm cable shall be considered as 1 running metre. (ii) colour code shall be Red for phase, Black for neutral and green for earth

Supply and fixing sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 10 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 10 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 32/40mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 10 sqmm and one single core earth cable of 10 sqmm cable shall be considered as 1 running metre. (ii) colour code shall be Red for phase, Black for neutral and green for earth

LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver,including lamp bracket upto 1.5metre length as per suitable for fitting including clamp with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection, including taking down old street lght complete all as specified and directed.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth Complete all as specified and directed .

LED panel recess mounted ultra slim 2'x2' - 36 watts ultra slim (cool day) ceiling light, aluminum extruded housing with milky diffuser, heat exchanger unit, LED driver, surge protection complete suitable for perfect lighting cutting hole of required size in POP/false ceiling making good disturbed including taking down any type ceiling fitting complee all as specified and directed.

Exhaust fan energy efficient metallic blades heavy duty turbo force of size 300mm sweep, 1200 rpm, AC 230 volts complete with louvers shutters mounting on wall with holding down bolts, nuts, washers complete all as specified and directed.

Cutting openings, through brick walls in round shape , for 300mm dia exhaust fan and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required including finishing and matching the disturbed surface and removing surplus unserviceable bricks, hard-core, etc..from site and rubbish complete all as specified & directed by Engineer-in-charge.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, burried directly in ground vertically to a depth not less than 2.25m below normal ground level, with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI light grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of presast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Sch Part-I (2009), complete including dismantling of old earthing, all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) unit rate including protection pipe and GI wire 4.00mm dia from top to earth plate upto 7.5 meter

MS R G ENTERPRISES (BID ID -3224881)

PARVEEN KUMAR AND SONS (BID ID -3220158)

M/s Krishan Aggarwal (BID ID -3220622)