Special Repair of Primary Health Centre at Fatehpuri in Rewari District. (Re-Invited)

Amount

Removing doors and windows (wooden and steel) together with the dismantling of walls (HSR 8.17) (a) Door

Window

Supplying and fixing glass panes including special metal sash putty of approved make (b) glass panes 4 mm thick, exceeding 40 sq dm areas (HSR 18.30 (b))

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash,etc.,(non-coniferous timber other teak,conforming to I.S.specification No.1003, kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail, and wire gauze of 140G or 120G designation including cost of iron hinges, screws,chocks/cleats,stops nail etc.,complete fixed in position (excluding the cost of any fitings,other than specified above,but including labour for fixing the same in position)- (style and rails of windows shutter shall be 75 mm wide) (HSR 17.92 - Note)

Factory manufactured solid flush door shutters, with block board core as per I.S.No.16591969 bonded with water proof type phenol formaldehyde synthetic resin,hotpressesd,conforming to I.S.2202 part I and II, fixed in position,including iron hinges,screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges.) (HSR 17.93 (a) (iii) - Note)

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash etc. (non-conferous timber other than teak,conforming to I.S. specification No.1003, kiln-seasoned), with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete, fixed in position (excluding the cost of any fittings,other than specified above,but including labour for fixing the same in position). [HSR 17.90 b] - Note

12 mm thick cement plaster 1:4 (HSR 15.5)

Painting one coat with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint (HSR 16.7)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. (HSR 16.1)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or matallic or plastered or concrete surfaces to give an even shade. (HSR 16.3)

Painting two coats excluding priming coat with ready-mixed paint for metallic surfaces in all shades on new steel or iron work. (HSR 16.17)

Cement pointing 1:2 deep variety on brick and tile work. (HSR 15.60)

Antitermite Treatment (using Aldrin) (b) Post construction Work (iii) treatment of soil of existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement- mortar 1: 2 (1 cement : 2 coarse sand) to match the existing floors. [HSR 6.15 (b) (III)]

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint. (HSR 16.79) (b) Ist Quality

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). ((b) Bib cock sparrow with Perimix and flange (HSR 30.75 (b)

EXTRA FOR PROVIDING AND FIXING VITREOUS automatic flushing CISTERN INCLUDING FITTINGS and brackets instead of C.I. flushing cistern COMPLETE. ((b) 10 Litres capacity cistern (i) White (HSR 30.37 (b) (i))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the approval of the Engineerin-charge) including china plug for tap hole where necessary ; R.S. or C.I.BRACKETS for building into wall including painting; 32mm C.P.BRASS WASTE WITH C.P. brass chain and rubber plug; 15mm C.P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS, FLOORS AND PAINTING OF FITTINGS ETC. WHITE (i) Size 510mm X 400 mm with one no. tap (HSR 30.41 (i))

Providing and fixing in position quality stainless steel sink built in draining board of size 600mm X 450 mm complete as described in item no.30.53 and 30.58 above. (a) Sink size 600 X 450 X 200 mm (HSR 30.53 (a))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge) INDIAN TYPE WATER CLOSET SUITE CONSISTING OF:- (i) Closet set VITREOUSCHINAWARE W.C.PAN WITH horizontal inlet, for sinking into floor with A PAIR OF FOOTRESTS, 100 MM H.C.I’P’ TRAP WITH or without vent a required and suitable joint for closet inlet; (HSR 30.1 (i))

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing over flow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks completein all respects to the satisfaction of Engineer-In-Charge. (Except civil work).(HSR 30.119)

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres (HSR 6.6)

Cement Concrete 1:8:16 with brick ballast 40mm nominal size in foundation and plinth. (HSR 10.26)

First class brick laid in cement sand mortar 1:4 in foundation and plinth. (HSR 11.4)

Damp proof course 25 mm thick of cement concrete 1:2:4 using stone aggregate 20mm nominal size with 2 coats of bitumen 20/30 penetration, at 1.65 Kg per sqm laid hot and sanded. (HSR 10.115 - Note)

First class brickwork laid in cement sand mortar 1:4 in first storey upto 4 meters above plinth level. (HSR 11.9)

15 mm thick cement plaster 1:6 on the rough side of single or half brick wall (HSR 15.12)

(a) Striking joints in lime or cement on brick and tile walls (HSR 15.69 (a))

White Washing Three coats (HSR 16.48)

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on new work, two coats to give an even shade. (HSR 16.61)

Recovery items: The rates quoted against recovery items will not be included in the total amount rather is will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layer have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specification) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under:- (a) Fuel Wood @ 700 P.Cum Note: - All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this road. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price. Note:- 1 In case of any difference in the unit and nomenclature of any of the HSR items of Civil & E.I, work depicted in this DNIT and the given in HSR, the unit nomenclature given in HSR shall be applicable.

Deepak Kumar Contractor