Special repair

SCHEDULE ‘A’ PART- I ( Roof Treatment of 01 Block of Type-III accn (G+II ) Demolishing cement concrete nominal concrete 1:3:6 or richer mix manually/ by mechanical means including disposal of materials within 50 m lead as per direction of Engineer – In – Charge on roof slab.

Providing and laying of grading roof for water proofing treatment with cement concrete 1:2:4 with graded stone aggregates 20 mm nominal size

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :

Distempering with oil bound washable distemper approved brand and manufacturer to given an even shad in old work (one or more coats) incl preparation of old surface by removing old paint by scrapping, sand papering incl necessary repairs to scratches etc complete.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer , over the plastered wall surface to prepare the surface even and smooth complete.

Dismantling of old plaster or skirting raking out joints and cleaning the surface for plaster incl disposal of rubbish to the dumping ground within 50 mtr lead.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead :

Providing and Painting two or more coats with synthetic enamel paint of approved brand and manufacture to give an even shade.

SCHEDULE ‘B’ PART- I ( 12 Nos Type-I married Accommodation ) Distempering with oil bound washable distemper approved brand and manufacturer to given an even shad in old work (one or more coats) incl preparation of old surface by removing old paint by scrapping, sand papering incl necessary repairs to scratches etc complete.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer , over the plastered wall surface to prepare the surface even and smooth complete.

Providing and Painting two or more coats with synthetic enamel paint of approved brand and manufacture to give an even shade.

Dismantling of old plaster or skirting raking out joints and cleaning the surface for plaster incl disposal of rubbish to the dumping ground within 50 mtr lead.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead :

Dismantling doors shutters including chowkhats, holdfasts etc complete of area 3 sqm and below.

Providing and fixing 35mm thick factory made laminated flush door shutters decorative type, core of block boards construction with frame of 1st class hard wood including stainless steel butt hinges with screws etc complete.

Providing and fixing of mosquito proof shutters using galvanized MS wire gauge of average width of aperature 1.4mm in both directions with wire of dia 0.63mm for door of 35mm with 2nd class teak wood.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : (25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws)

Providing and fixing factory made 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles as per manufacturer's specifications and direction of Engineer-in-charge.(Non decorative finish)

Providing and fixing aluminium handles of size : 100 mm, transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing aluminium tower bolts of size : 100x10 mm with necessary screws etc. Complete.

Supply and fixing aluminum sliding door bolts, transparent or dyed to required colour or shade, with nuts and screws etc complete of size 250x16mm.

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: with 4mm thick glass panes.

SCHEDULE ‘A’ PART- II ( PLUMBING AND SANITARY FITTINGS ) Providing and fixing 32 mm dia flexible P.V.C waste pipe for sink or wash basin including P.V.C waste fittings complete.(Flexible pipe)

Providing and fixing of 15mm nominal bore CP bib cock of approved quality.

Providing and fixing of 15mm nominal bore CP angle cock of approved quality.

Providing and fixing of 15mm nominal bore connection pipe of approved quality.

Providing and fixing PTMT pillar cock of approved quality and colour .

Providing and fixing P.V.C. low level flushing cistern 10 litre capacity - White with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

Providing and fixing 600x450mm beveled edge mirror of superior glass ( of approved quality) complete with 6 mm thick hard board backing fixed to wooden cleats with CP brass screws and washers complete.

Providing and fixing of 100mm dia CP brass shower rose with 15 or 20mm inlet of approved quality.

Providing and fixing white vitreous pedestal type china wash hand basin (Size 630x450 mm) incl pedestal with C.I. Brackets, 15 mm C.P Brass pillar taps, 32 mm C.P. Brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required etc. complete.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing on wall unplasticised rigid PVC pipes incl jointing with seal ring, single socketed pipes of 100 mm dia.

Providing and fixing on wall unplasticised rigid PVC pipes incl jointing with seal ring, single socketed pipes of 75 mm dia.

SCHEDULE ‘A’ PART- III ( INTERNAL ELECTRIFICATION WORK) Rewiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable and 1.5 and 1.5 sq.mm. FR PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit with modular switch , modular plate, suitable GI box and earthing the point with 1.5 sqmm FR PVC insulated copper conductor single core cable including dismantling as required.

Supply and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supply and fixing 5/6 amps switch piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing 3 pin 5/6 amp socket outlet piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing 15/16 amps switch piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing 15/16 amps switch piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing bell push piano type switch/ socket on the existing switch box/ cover including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required (Upto 450 mm sweep)

SCHEDULE ‘C’ PART- I (09 Nos Type-III married accommodation) Distempering with oil bound washable distemper approved brand and manufacturer to given an even shad in old work (one or more coats) incl preparation of old surface by removing old paint by scrapping, sand papering incl necessary repairs to scratches etc complete.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer , over the plastered wall surface to prepare the surface even and smooth complete.

Providing and Painting two or more coats with synthetic enamel paint of approved brand and manufacture to give an even shade.

Dismantling of old plaster or skirting raking out joints and cleaning the surface for plaster incl disposal of rubbish to the dumping ground within 50 mtr lead.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead :

Dismantling doors shutters including chowkhats, holdfasts etc complete of area 3 sqm and below.

Providing and fixing 35mm thick factory made laminated flush door shutters decorative type, core of block boards construction with frame of 1st class hard wood including stainless steel butt hinges with screws etc complete.

Providing and fixing of mosquito proof shutters using galvanized MS wire gauge of average width of aperature 1.4mm in both directions with wire of dia 0.63mm for door of 35mm with 2nd class teak wood.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : (25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws)

Providing and fixing factory made 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles as per manufacturer's specifications and direction of Engineer-in-charge.(Non decorative finish)

Providing and fixing aluminium handles of size : 100 mm, transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing aluminium tower bolts of size : 100x10 mm with necessary screws etc. Complete.

Supply and fixing aluminum sliding door bolts, transparent or dyed to required colour or shade, with nuts and screws etc complete of size 250x16mm.

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: with 4mm thick glass panes.

SCHEDULE ‘A’ PART- II ( PLUMBING AND SANITARY FITTINGS ) Providing and fixing 32 mm dia flexible P.V.C waste pipe for sink or wash basin including P.V.C waste fittings complete.(Flexible pipe)

Providing and fixing of 15mm nominal bore CP bib cock of approved quality.

Providing and fixing of 15mm nominal bore CP angle cock of approved quality.

Providing and fixing of 15mm nominal bore connection pipe of approved quality.

Providing and fixing PTMT pillar cock of approved quality and colour .

Providing and fixing P.V.C. low level flushing cistern 10 litre capacity - White with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

Providing and fixing 600x450mm beveled edge mirror of superior glass ( of approved quality) complete with 6 mm thick hard board backing fixed to wooden cleats with CP brass screws and washers complete.

Providing and fixing of 100mm dia CP brass shower rose with 15 or 20mm inlet of approved quality.

Providing and fixing white vitreous pedestal type china wash hand basin (Size 630x450 mm) incl pedestal with C.I. Brackets, 15 mm C.P Brass pillar taps, 32 mm C.P. Brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required etc. complete.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Demolishing cement concrete nominal concrete 1:3:6 or richer mix manually/ by mechanical means including disposal of materials within 50 m lead as per direction of Engineer – In – Charge on roof slab.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of : (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying in position cement concrete of 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centering and shuttering etc.

Providing and laying non skid ceramic floor tiles of size 300x300mm ( thickness to be specified by the manufacturer) of approved make, in all colours and shades except white, Ivory, Grey laid on 20mm thick CM 1:4 (1cement :4 coarse sand), incl grouting the joints with white cement and matching pigments. etc. complete.

Providing and fixing water closet squatting pan ( Indian type WC pan) with 100mm sand cast iron P or S trap, 10 ltr P.V.C low level flushing cistern (white) with manually controlled device (handle lever) and flush pipe with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. ( Orissa pattern WC pan size 580x440mm with integral type foot rests) (Make - Hindware/Paryware/Hindustan)

Providing and fixing on wall unplasticised rigid PVC pipes incl jointing with seal ring, single socketed pipes of 100 mm dia.

Providing and fixing on wall unplasticised rigid PVC pipes incl jointing with seal ring, single socketed pipes of 75 mm dia.

SCHEDULE ‘A’ PART- III ( INTERNAL ELECTRIFICATION WORK) Rewiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable and 1.5 and 1.5 sq.mm. FR PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit with modular switch , modular plate, suitable GI box and earthing the point with 1.5 sqmm FR PVC insulated copper conductor single core cable including dismantling as required.

Supply and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supply and fixing 5/6 amps switch piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing 3 pin 5/6 amp socket outlet piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing 15/16 amps switch piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing 15/16 amps switch piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing bell push piano type switch/ socket on the existing switch box/ cover including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required (Upto 450 mm sweep)

SCHEDULE ‘D’ PART- I (01 Nos Type-III married Accommodation) Distempering with oil bound washable distemper approved brand and manufacturer to given an even shad in old work (one or more coats) incl preparation of old surface by removing old paint by scrapping, sand papering incl necessary repairs to scratches etc complete.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer , over the plastered wall surface to prepare the surface even and smooth complete.

Providing and Painting two or more coats with synthetic enamel paint of approved brand and manufacture to give an even shade.

Dismantling of old plaster or skirting raking out joints and cleaning the surface for plaster incl disposal of rubbish to the dumping ground within 50 mtr lead.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead :

Dismantling doors shutters including chowkhats, holdfasts etc complete of area 3 sqm and below.

Providing and fixing 35mm thick factory made laminated flush door shutters decorative type, core of block boards construction with frame of 1st class hard wood including stainless steel butt hinges with screws etc complete.

Providing and fixing of mosquito proof shutters using galvanized MS wire gauge of average width of aperature 1.4mm in both directions with wire of dia 0.63mm for door of 35mm with 2nd class teak wood.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : (25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws)

Providing & fixing Pre painted fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.(Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides)

Providing and fixing glass panes with putty and glazing clips in steel doors, windows and ventilators all complete with 4mm thick glass panes.

Providing and fixing factory made 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles as per manufacturer's specifications and direction of Engineer-in-charge.(Non decorative finish)

Providing and fixing aluminium handles of size : 100 mm, transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing aluminium tower bolts of size : 100x10 mm with necessary screws etc. Complete.

Supply and fixing aluminum sliding door bolts, transparent or dyed to required colour or shade, with nuts and screws etc complete of size 250x16mm.

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: with 4mm thick glass panes.

Providing and fixing of curtain rods of 1.25mm thick chromium plated brass plate , with two chromium plated brass brackets fixed with CP brass screws and wooden plugs etc, wherever necessary complete of size 20mm dia.

SCHEDULE ‘A’ PART- II ( PLUMBING AND SANITARY FITTINGS ) Providing and fixing 32 mm dia flexible P.V.C waste pipe for sink or wash basin including P.V.C waste fittings complete.(Flexible pipe)

Providing and fixing of 15mm nominal bore CP bib cock of approved quality.

Providing and fixing of 15mm nominal bore CP angle cock of approved quality.

Providing and fixing of 15mm nominal bore connection pipe of approved quality.

Providing and fixing PTMT pillar cock of approved quality and colour .

Providing and fixing P.V.C. low level flushing cistern 10 litre capacity - White with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

Providing and fixing 600x450mm beveled edge mirror of superior glass ( of approved quality) complete with 6 mm thick hard board backing fixed to wooden cleats with CP brass screws and washers complete.

Providing and fixing of 100mm dia CP brass shower rose with 15 or 20mm inlet of approved quality.

Providing and fixing white vitreous pedestal type china wash hand basin (Size 630x450 mm) incl pedestal with C.I. Brackets, 15 mm C.P Brass pillar taps, 32 mm C.P. Brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required etc. complete.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Demolishing cement concrete nominal concrete 1:3:6 or richer mix manually/ by mechanical means including disposal of materials within 50 m lead as per direction of Engineer – In – Charge on roof slab.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of : (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying in position cement concrete of 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centering and shuttering etc.

Providing and laying non skid ceramic floor tiles of size 300x300mm ( thickness to be specified by the manufacturer) of approved make, in all colours and shades except white, Ivory, Grey laid on 20mm thick CM 1:4 (1cement :4 coarse sand), incl grouting the joints with white cement and matching pigments. etc. complete.

Providing and fixing water closet squatting pan ( Indian type WC pan) with 100mm sand cast iron P or S trap, 10 ltr P.V.C low level flushing cistern (white) with manually controlled device (handle lever) and flush pipe with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. ( Orissa pattern WC pan size 580x440mm with integral type foot rests) (Make - Hindware/Paryware/Hindustan)

Providing and fixing on wall unplasticised rigid PVC pipes incl jointing with seal ring, single socketed pipes of 100 mm dia.

Providing and fixing on wall unplasticised rigid PVC pipes incl jointing with seal ring, single socketed pipes of 75 mm dia.

SCHEDULE ‘A’ PART- III ( INTERNAL ELECTRIFICATION WORK) Rewiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable and 1.5 and 1.5 sq.mm. FR PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit with modular switch , modular plate, suitable GI box and earthing the point with 1.5 sqmm FR PVC insulated copper conductor single core cable including dismantling as required.

Supply and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supply and fixing 5/6 amps switch piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing 3 pin 5/6 amp socket outlet piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing 15/16 amps switch piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing 15/16 amps switch piano type on the existing switch box/ cover including connections etc. as required.

Supply and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing bell push piano type switch/ socket on the existing switch box/ cover including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required (Upto 450 mm sweep)

aarav enterprises

M/S. MAHESHWARI CONSTRUCTION

M/S. SHIVAM ENTERPRISES