Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹28.3 LAccepted-AOC VILL BHANDWAR PO CHANDPUR 165 TEHSIL SADAR DISTT BILASPUR HP 174004 | BILASPUR | BILASPUR | HIMACHAL PRADESH | 174004 | ₹28.3 L Quoted ₹28.6 L | L1 | Accepted-AOC Being lowest |
| 2 | L2₹28.8 LRejected-Finance BROADWAY SHIVPORA SRINAGAR 190004 J K | SRINAGAR | SRINAGAR | J K | 190004 | ₹28.8 L | L2 | Rejected-Finance Other than L1 |
| 3 | L3₹29.9 LRejected-Finance H NO 1395 SECTOR 21 PANCHKULA 134112 HARYANA | PANCHKULA | HARYANA | 134112 | ₹29.9 L | L3 | Rejected-Finance Other than L1 |
| Sl No | Description | Qty | Unit | R B TRADERS L3 | H M INFOTECH L1 | LEO TRADERS L2 |
|---|---|---|---|---|---|---|
| 1.00 | Demolition of cement concrete (un reinforced) in ground floors and pavings not exc 15 cm thick (below or above ground level) and removing debris off the premises complete all as specified and/or as directed by Engr-in-Charge. | 2.88 | Cum | 250 ₹720 | 450 ₹1,296 | 400 ₹1,152 |
| 2.00 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing debris off the premises, complete all as specified and/or as directed by Engr-in-Charge. | 1.5 | Cum | 250 ₹375 | 450 ₹675 | 400 ₹600 |
| 3.00 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing), removing rubbish off the premises complete all as specified and/or as directed by Engr-in-Charge. | 115 | Sqm | 20 ₹2,300 | 50 ₹5,750 | 100 ₹11,500 |
| 4.00 | Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) etc. any thickness including covered fillets and supporting members, complete all as specified and/or directed by Engr-in-Charge. | 316 | Sqm | 20 ₹6,320 | 50 ₹15,800 | 20 ₹6,320 |
| 5.00 | Dismantling unframed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc. under 40 sqcm in section, complete all as specified and/or directed by Engr-in-Charge. | 1,150 | RM | 10 ₹11,500 | 10 ₹11,500 | 10 ₹11,500 |
| 6.00 | Demolition of precast concrete block walling built in cement mortar including all quoins, arches, pillars etc. complete all as specified and/or directed by Engr-in-Charge. | 6.85 | Cum | 250 ₹1,712.50 | 450 ₹3,082.50 | 400 ₹2,740 |
| 7.00 | Dismantling boarding, any description, fixed in any position with nails, complete all as specified and/or directed by Engr-in-Charge. | 45 | Sqm | 20 ₹900 | 25 ₹1,125 | 20 ₹900 |
| 8.00 | Taking down cement plaster on brick/PCC block or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and/or as directed by Engr-in-Charge. | 298 | Sqm | 20 ₹5,960 | 50 ₹14,900 | 5 ₹1,490 |
| 9.00 | Taking down chowkat or frame with shutters (without taking of shutters from the frame) not exc 1.5 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge. | 6 | Each | 100 ₹600 | 150 ₹900 | 400 ₹2,400 |
| 10.00 | Taking down chowkat or frame with shutters (without taking of shutters from the frame) exc 1.5 sqm each but not exc 4 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge. | 7 | Each | 150 ₹1,050 | 200 ₹1,400 | 400 ₹2,800 |
Updated dates
Tender Value
₹28.1 L
EMD Value
₹56,200
Closing Date
24 Nov 2025, 6:00 pmClosed
CWE, HQ 138 WE
CWE, HQ 138 WE
SPECIAL REPAIR OF BLDG NO P-60 AND PROVN OF 03 X TOILET CUM BATHROOM FOR OR AT AVN BDE UNDER GE 865 EWS
2025_MES_725820_3
138WE/L-162/2025-26
Open Tender
Civil Works
180 days
GE 865 EWS
Please refer Tender documents.
6 documents required · 6 mandatory
₹500
GE 865 EWS
₹56,200
Yes
22 Jan 2026
28 Oct 2025
1 Dec 2025
28 Oct 2025
24 Nov 2025
4 Nov 2025
Amount
Demolition of cement concrete (un reinforced) in ground floors and pavings not exc 15 cm thick (below or above ground level) and removing debris off the premises complete all as specified and/or as directed by Engr-in-Charge.
Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing debris off the premises, complete all as specified and/or as directed by Engr-in-Charge.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing), removing rubbish off the premises complete all as specified and/or as directed by Engr-in-Charge.
Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) etc. any thickness including covered fillets and supporting members, complete all as specified and/or directed by Engr-in-Charge.
Dismantling unframed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc. under 40 sqcm in section, complete all as specified and/or directed by Engr-in-Charge.
Demolition of precast concrete block walling built in cement mortar including all quoins, arches, pillars etc. complete all as specified and/or directed by Engr-in-Charge.
Dismantling boarding, any description, fixed in any position with nails, complete all as specified and/or directed by Engr-in-Charge.
Taking down cement plaster on brick/PCC block or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and/or as directed by Engr-in-Charge.
Taking down chowkat or frame with shutters (without taking of shutters from the frame) not exc 1.5 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge.
Taking down chowkat or frame with shutters (without taking of shutters from the frame) exc 1.5 sqm each but not exc 4 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge.
M&L for not less than 15mm thick wooden battens of 100mm wide fixed each other with male and female grooves fixed with screws to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed.
M&L for not less than 15mm thick wooden battens of 100mm wide fixed each other with male and female grooves fixed with screws to timber frame work as in ceiling panelling, complete all as specified and as directed.
Hacking out old broken glass (any thickness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and/or directed by Engr-in-Charge.
M&L 6mm (5 ply) thick veneered decorative (Knoty Pine) plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work in wall, complete all as specified and as directed.
M&L 6mm (5 ply) thick veneered decorative (Knoty Pine) plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work in ceiling, complete all as specified and as directed.
M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed.
M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in ceiling panelling, complete all as specified and as directed.
M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and not exc 25 sqcm in section, complete all as specified and directed by Engr-in-Charge
M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 6 sqcm and not exc 13 sqcm in section, complete all as specified and/or as directed by Engr-in-Charge.
M&L for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws complete all as specified and/or as directed by Engr-in-Charge.
M&L Prelaminated particle board,18/19 mm thick, prelaminated both side interior grade, one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and as directed.
M&L for 75 mm thick PCC 1:3:6 type C-2 (using 20mm graded aggregate) as plinth protection finished even and smooth with out using extra cement, complete all as specified and/or as directed by Engr-in-Charge.
M&L Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' in plinth protection, complete all as specified and/or as directed by Engr-in-Charge.
M&L for PCC 1:4:8, type D2 (using 40mm graded crushed aggregate) as in mass concrete and filling of foundation, complete all as specified and/or as directed by Engr-in-Charge.
M&L for Cement concrete type 1:4:8, D-2, (using 40mm stone graded aggreate) 100 mm thick as in sub -floors, sub- bases, etc., complete all as specified and as directed.
M&L for Cement concrete type 1:4:8, D-2, (using 40mm stone graded aggreate) 75 mm thick as in sub -floors, sub- bases, floors and pavings etc., complete all as specified and as directed.
M&L PCC 1:3:6 type C-2 (using 20mm graded stone aggregate) 75mm thick sub base of floor etc., complete all as specified and directed.
M&L for Chequred cement concrete tiles (glazed) 30cm X 30cm X 20mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments .Layed over 20mm thick cement screed base (1:6) and all as directed by Engr-in - charge.
Demolition of reinforced cement concrete of any description and position not otherwise specifically provided for.
M&L for reinforced cement concrete (Nominal Mix) 1:2:4 type B1 (20mm graded aggregate) as in slabs supported of walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc. complete all as specified and/or as directed by Engr-in-Charge.
M&L for precast cement concrete 1:2:4 type B1 (20mm graded aggregate) in landings, cover slabs (for manholes etc.), chullah hoods, chhajja, water troughs, shelves and similar articles with plain faces, set in CM 1:6, complete all as specified and/or as directed by Engr-in-Charge.
M&L for form work to soffits of suspended slabs flat type such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or slopping etc.) complete all as specified and/or as directed by Engr-in-Charge.
M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and/or as directed by Engr-in-Charge.
M&L mild steel TMT bars, 6mm dia and over, cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips as in stirrups, spacer, binders, etc complete all as specified and directed.
M&L for hardcore of broken stone gauge nexc 63mm, deposited, spread and levelled in layers not exc. 15cm thick watered and rammed to a true surface. complete all as specified and as directed.
S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guide, for sliding doors fixed with angle cleats or other connecting plates and similar work conforming to Fe -290 Gde E-165, complete all as specified and/or directed by Engr-in-Charge.
Preparation of new/ previous untreated steel surface of any description over 10cm grith or width, not otherwise described with one coat of red oxide zinc chrome primer followed by two coats of synthetic enamel paint complete all as specified and directed.
M&L precast solid blocks in cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in block masonry, exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by Engr-in-Charge.
M&L for 10mm thick rendering on fair faces of block/ brick wall works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and/or directed by Engr-in-Charge.
M&L for 5 mm thick rendering on ceiling finished even and smooth without using extra cement in cement mortar 1: 3 complete all as specified and/or directed by Engr-in-Charge.
M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 including mixing of liquid water proofing compound as per manufacturer's instructions complete all as specified and as directed by Engineer-in-Charge. Note : WPC will be measured and paid separately.
Supply only integral liquid water proofing compound. Make : Pidilite/Sika/Asian paints.
M&L for preparation of new plastered wall surface of any description and applying two coats of cement based paint over a coat of chalk whiting complete all as specified and/or as directed by Engr-in-Charge.
M&L French polishing on wood or wood based surface of any width or girth or any description, including cleaning and preparing the surface including a coat of wood filler on new surface with two or more coats to obtain required finish complete all as specified and as directed.
S&F 35mm thick 2nd class hard wood plain framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and/or as directed by Engr-in-Charge.
S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and/or as directed by the Engr-in-Charge.
M&L for powder coated aluminium door shutters, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, hinge type B-21 100 mm long (3 Nos) suitable handle (2 Nos), complete all as specified and/or as directed by Engr-in-Charge. Note : Glass / Wiremesh be measured separately.
S&F anodised aluminium window and ventilator shutters, including aluminium jali fixed in one side, side hung type without sashbars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (2 Nos) suitable handle (1 No) etc. complete all as specified and/or as directed by Engr-in-Charge. Note : Glass / Wiremesh be measured seperately.
S&F factory made aluminium 50 micron powder coated grill, opening size 101.6 X 63.5 mm (4"X2½") and of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows in all respect as specified
S&F 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and/or as directed by the Engr-in-Charge.
S&F 2nd class hard wood 35 mm thick Glazed and Skelton shutter, open and prepared to receive the glass, gauze etc. (without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc., complete all as specified and/or as directed by Engr-in-Charge. Note : Glass / Wiremesh be measured seperately.
S&F for 30mm thick 2nd class hard wood plain framed factory made glazed and skeletion window/ventilator shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beds for securing glass etc size of members of shutters as specified in SSR part I, Section 8, clause 8.24(a) supplied and fitted to chowkats, complete all as directed by Engr-in-Charge.
M&L for preparation of new untreated wood or wooden based surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and/or as directed by Engr-in-Charge.
M&L sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc. 0.50 sqm in each pane complete all as specified and/or as directed by Engr-in-Charge.
M&L sheet glass 5.5mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc. 0.50 sqm in each pane complete all as specified and as directed.
S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and/or as directed by Engr-in-Charge.
S&F repair 300mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.
S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and/or as directed by Engr-in-Charge.
S&F100mm long mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed.
S&F 100mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and/or as directed by Engr-in-Charge.
S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and/or as directed by Engr-in-Charge.
S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and/or as directed by Engr-in-Charge.
S&F in repair aluminium (die cast) body door closer hydraulically designation No 3 universal type suitable for door shutter of 851 to1000mm in width and weight 61 to 80 kg complete all as specified and/or as directed by Engr-in-Charge.
S&F floor door stopper (length of cover plate) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and/or as directed by Engr-in-Charge.
S&F 75mm long aluminium anodized, butt hinges of extruded section type C-21, complete all as specified and/or as directed by Engr-in-Charge.
S&F 100mm long aluminium anodized, butt hinges of extruded section type B-21, complete all as specified and/or as directed by Engr-in-Charge.
S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and/or as directed by Engr-in-Charge.
S&F continuous (piano) hinges, stainless steel, width of flap when open 40 mm complete all as specified.
S&F hasp and staple 125 mm, mild steel, safety type, stove enameled black, including bolt to hinge plate including fixing screws, complete all as specified.
S&F auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for cabinet shutters complete in all respect and fixed in position all as specified. Make : KAFF/Hettich or equivalvent approved make as approved by GE.
S&F tower bolts 250mm long of stainless steel 304 finished/of outer plate metal matt finished complete fixed in position all as specified. Make : Harrison (Cat No 0812) or equivalvent approved make as approved by GE.
S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 200mm long matt finished complete fixed in position all as specified. Make : Harrison (Jasmine) or equivalvent approved make as approved by GE.
S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified. Make : Hettitch or equivalvent approved make as approved by GE.
S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified. Make : Harrison (Jasmine) or equivalvent approved make as approved by GE.
M&L for 25 mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in sub floor complete all as specified and/or as directed by Engr-in-Charge.
M&L for joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exc. 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and/or as directed by Engr-in-Charge.
M&L for 15-18 mm thick granite stone (any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite including cutting etc. and screed bed with CM (1:4) 20mm thick for laying floor tiles complete all as specified and/or as directed by Engr-in-Charge.
M&L for glazed ceramic coloured tiles in vertical surfaces of size 450x350x7mm/ 350x250x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering 10 mm thick in cement mortar (1:4) as in backing coat complete all as specified and/or as directed by Engr-in-Charge.
M&L for dismantling water tanks exc 250 but not exc 500 Litres, and removing to store, complete, all as specified and as directed by the Engineer-in-Charge.
S&F tripple layered rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 litres including all accessories, complete all as specified and/or as directed by Engr-in-Charge.
S&F in repairs 25mm bore stop valve chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule, complete all as specified and as directed.
S&F in repairs 25mm ball brass valves, high pressure with polythene float and fly nut complete screwed for iron/PPR, complete all as specified and as directed.
S&F in repairs Towel Hanger with 6 Nos of pin and 600mm long chromium plated etc. complete all as specified and/or as directed by Engr-in-Charge.
S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and/or directed by Engr-in-Charge.
M&L for hard wood 2nd class factory made wooden boarded floors 10mm thick and skirtings planed one side & edges tonged and grooved or rebated, including backing with thermocol sheets, over 6 micron polythylene sheeting over the concrete to minimize moisture migration from the concrete complete all as specified by manufacture all as specified and directed.
M&L preparation of newely plaster surfaces and applying 02 coats of distemper oil emulsion paint (light shade) @ 10 sq.m/litre/2 coats by using roller/brush to new surfaces , over a coat of putty thickness vary from 1 to 1.5 mm over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.
M&L preparation of newely plaster surfaces and applying 02 coats of exterior emulsion paint (light shade) @ 5 sq.m/litre/2 coats by using roller/brush to new surface of walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over a coat of wall putty thickness vary from 1 to 1.5 over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed.
M&L applying 02 coats of exterior emulsion paint (light shade) @ 5 sq.m/litre/2 coats by using roller/brush to old external wall surfaces walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over a coat of wall putty thickness vary from 1 to 1.5 over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer, including complete removal of existing treatment ocomplete all as specified and directed.
M&L for preperation of new concrete/ plastered surface of ceiling of, any description and applying three coats of white wash complete all as specified and as directed.
M&L for preperation of new plastered wall surface of any description and applayng three coats of white wash complete all as specified and as directed.
S&F in repair 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs complete all as specified and/or directed by Engr-in-Charge.
S&F vitreous china urinal half stall type, white complete including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with and including 60 mm brass screws, pointing around urinal back in cement, fixing grating and union for discharge pipe excluding flushing cistern, flush pipe but including CP waste coupling, PTMT urinal spreader, etc. complete all as specified and as directed by the Engr-in-Charge.
S&F Vitreous China wash basin fancy type pedestal pattern, white, flat back, size 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified and/or directed by Engr-in-Charge.
All as per Ser item No 93 above, but in repairs.
S&F water closet white vitreous china ware Orissa pattern of size 580 x440mm with integral foot rest ‘P’ or ‘S’ trap 100mm bore front or back inlet incl provision of PCC bedding type B1, 1:2:4 (using 20 mm graded aggregate) and connection pipes (excluding flushing cistern but including flushing pipe 32 mm dia MS chromium plated), complete all as specified and directed.
S&F 15 mm bore pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe.
S&F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engr-in-Charge.
S&F sheet glass basin shelf assembly consisting of 8mm thick glass shelf 300 x 300mm wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and directed.
S&F sheet glass basin shelf assembly consisting of 8mm thick glass shelf 600 x 150mm wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and directed.
S&F soap dish, any type, fixed to plugs with chromium plated brass screws completed all as specified and directed.
S&F CP toilet jet spary ABS with double lock 1.2 mtr CP tube stainless steel flexible hose complete all as specified and/or directed by Engr-in-Charge.
S&F towel rod brass CP 60 cm long between flanges and including all accessories like brackets/ screws etc as recommended by manufacturer and complete fixed in position complete all as specified and/or directed by Engr-in-Charge.
All as per Ser item No 102 above, but in repairs.
S&F in repair grating doom 75mm dia of PTMT (min weight 25gms) complete all as specified and/or directed by Engr-in-Charge.
S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete.all as specified and as directed by the Engr-in-Chage
M&L PCC 1:3:6, type C1 (using 20 mm graded stone aggregate) as in hold fast, bed block and like complete all as specified and as directed by the Engr-in-Charge.
S&F vitreous China wash down water closet (pedestal), white (EWC) including plastic sheet cover of same colour of WC, closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as specified and/or directed by Engr-in-Charge.
S&F in repair One Piece EWC with built in Cistern Vitreous china wash down water closet (Pedestal), white (EWC) including Plastic seat of same colour of WC, closed patttern with flat bottom, and cover and mild steel chromium plated hinging device complete with flushing cistern.
Supply only flushing cistern of PVC 10 ltr. cap. with dual flushing system, white colour, valveless symphonic action type, low level, with inlet, ball valve, float and including brackets and connection to pipe etc. incl all necessary accessories like rag bolts/ gel gasket etc as recommended by manufacturer for fixing, packing complete all as specified and/or directed by Engr-in-Charge.
S&F in repairs 15mm dia angle stop valves, fancy type chromium plated with long shank and cast copper alloy (concealed type), screwed down high pressure screwed both ends for iron pipes complete all as specified and/or directed by Engr-in-Charge.
S&F in repairs 15mm dia stop valves, fancy type chromium plated with long shank and cast copper alloy (concealed type), screwed down high pressure screwed both ends for iron pipes complete all as specified and/or directed by Engr-in-Charge.
S&F in in repairs 15mm bore CP wash basin mixer for mixing hot & Cold water copper alloy fancy type high pressure screwed for iron pipe complete all as specified and/or directed by Engr-in-Charge.
M&L for wall mounted mixer assembly, brass chromium plated, comprising of centre outlet tap, double inlets for hot & cold water, with telephonic shower arrangement, with connecting legs & wall flanges, inlets suitable for 15mm bore connections complete all as specified and directed. Make : Jaquar (Continental Series)/ Hindware (Contessa Plus Series)/ Cera (Ocean Series)/ Prayag (Neptune Series)
S&F in sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, Waste pipe including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.
S&F Sink Cock wall mounted with swinging spout and with wall flange, fancy type chromium plated cast copper alloy screwed down, high pressure, screwed one ends for 15mm bore of iron pipe or for union and fixed in position complete all as specified and directed. Make : Jaquar (Continental Series)/ Hindware (Contessa Plus Series)/ Cera (Ocean Series)/ Prayag (Neptune Series)
Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and/or directed by Engr-in-Charge.
M&L for PVC (SWR) pipe single socketed, 110mm soil, waste and rain water drainage pipes laid in trenches and jointed complete all as specified and/or directed by Engr-in-Charge.
M&L for PVC (SWR) pipe single socketed, 110mm soil, waste and rain water drainage pipes fixed with wall and jointed complete all as specified and/or directed by Engr-in-Charge.
S&F in PVC (SWR) 75 mm bore, single socketed in any length with rubber ring joints using solvent as per manufacture instruction, fixed with wall and jointed complete all as specified and/or directed by Engr-in-Charge.
S&F in PVC (HDPE) SWR 75 mm bore, single socketed in any length with rubber ring joints using solvent as per manufacture instruction, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.
S&F PVC (SWR) vent cowl of 75mm bore, complete all as specified and as directed.
S&F 110 mm dia PVC (SWR) bend any radius, complete all as specified and as directed.
S&F 75 mm dia PVC (SWR) bend any radius, complete all as specified and as directed.
M&L PVC (SWR) 75 mm dia floor trap with plain with grating including jointing with solvent cement complete all as specified and directed.
M&L stack clamp out of 50mm x5mm flat iron stays including bolt and nuts and securing ends of stays to walls or roof for 100mm bore pipe, complete all as specified and directed.
S&F sand cast iron 'P' or S trap 100mm bore for indian type water closet, complete all as specified and directed.
M&L for PCC 1:4:8, type D-2 (using 40mm graded stone aggerate) bed to drain pipe incl packing under and haunching against side after they are laid and tested up to 110mm dia pipe, complete all as specified and/or directed by Engr-in-Charge.
M&L for Cast iron Nahani trap 100mm with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed.
Taking up or down 25 mm to 32mm bore steel tubing and connections and set aside for re-use or removal to store, complete all as specified and/or directed by Engr-in-Charge.
S&F 25mm dia 3 layer PP-R polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engr-in-Charge.
S&F 32mm dia 3 layer PP-R polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engr-in-Charge.
S&F in repairs fancy type 15 mm bore chromium plated bib taps, cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed.
S&F 15mm bore, PVC connection pipe 600 mm long with PTMT nuts at both ends, complete all as specified and as directed.
All as per Ser item No 133 above, but 450 mm long.
S&F in repairs, 40mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams), complete all as specified and/or directed by Engr-in-Charge.
S&F in repairs, 32mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams), complete all as specified and/or directed by Engr-in-Charge.
All as per Ser item No 137 above, but in repairs.
Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified.
Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth, for foundation etc. or for shafts, wells cesspits, manholes, pier holes, etc. not exc 10 sqm on plan and not exc. 1.5m in depth in hard/dense of soil and getting out, complete all as specified and as directed.
Returning, filling in (soil), including spreading, levelling, watering and well ramming in layers not exc. 25cm, complete all as specified and directed by Engr in Charge.
Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified and directed by Engr in Charge.
M&L precast solid blocks in cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in block masonry, not exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by Engr-in-Charge.
M&L form work for rough finished concrete surfaces to sides and soffits of floor or roof beam ,beam haunchings ,girders, bresum-mers,lintles,cantilevers,shelves including supports ,overhanging, etc. also splays between floors and beams, etc, complete all as specified and directed.
Taking down carefully copper/ aluminium point wiring (light, fan, socket and power point) including complete fittings such as switches, ceiling rose, regulators, socket etc. and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface, complete all as specified and/or as directed by Engr-in-Charge.
Point wiring complete with 1.5 sqmm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts cable drawn through & including PVC casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5 sqmm copper conductor cable as continuous earth lead complete all as specified and/or directed by Engr-in-Charge for the followings:-
One light/exhaust fan point controlled by one way switch.
One light point controlled by two way switch.
One switch socket outlet 6 Amps, 230 volts point on same board.
One switch socket outlet 6 Amps, 230 volts point on independent board.
All as per Srl item No 146 above, but using cables 4 Sq mm size.
S&F switch piano flush button single pole 6 Amps 230 volts one way complete all as specified and/or directed by Engr-in-Charge.
Supply and fix switch piano 16 Amps, flush type, single pole, two way, 230 volt , AC supply, ISI Marked, complete all as specified and/or directed by Engineer-in-Charge.
S&F socket outlet two in one, 3 pin 6 Amps flush type.230 volts complete all as specified and/or directed by Engr-in-Charge.
S&F socket outlet two in one, 5 pin 6 Amps flush type.230 volts complete all as specified and/or directed by Engr-in-Charge.
S&F switch Socket combination outlet multi purpose 3 pin 6 Amps and 16 Amps 230 volts complete all as specified and/or directed by Engr-in-Charge.
Supply and fix switch socket combination 2 in 1, 3 pin, 6 Amp flush type 230 volts complete all as directed.
S&F ceiling rose, surface Bakelite three terminals complete all as specified and/or directed by Engr-in-Charge.
S&F in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 12 Ways complete all as specified and/or directed by Engr-in-Charge.
S&F sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 08 Ways complete all as specified and/or directed by Engr-in-Charge.
All as per Ser item No 156 above, but in repairs.
S&F MCB SPN 63 Amp 240 Volts AC ISI marked complete all as specified and/or directed by Engr-in-Charge.
S&F MCB SP 6-32 Amps. 240 Volts 50 HZ complete all as specified and/or directed by Engr-in-Charge.
Supply and fix in replacement LED light fitting 1X20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and/or directed by Engr-in-Charge. Make-Havells /Crompton/ Bajaj.
All as per Ser item No 161 above, but in repairs.
Supply and fix LED light fitting mirror type with high output diffuser 2 feet. 10 watt 220 V AC decorative type with driver holder and LED lamp connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed .
Supply and fix in repairs LED light fitting 10 watt 220 V AC decorative type with driver holder and LED lamp connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.
S&F LED luminaire 600 x 600 mm, 36 watt, 220 volt AC surface / recessed type with high efficiency PMMA difuser soft glair free light complete with driver, holders and LED lamp suitable for roof ceiling including connecting up with driver 3 core flexible copper conductor cases of suitable size complete all as specified and directed.
S&F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and/or directed by Engr-in-Charge.
M&L for submain wiring along with earth wire with the following sizes of FRLSH PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing caping wire size 2x10 sqmm + 1x10 sqmm earth wire including taking down complete all as specified and/or directed by Engr-in-Charge.
M&L for submain wiring along with earth wire with the following sizes of FRLSH PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing caping wire size 2x2.5 sqmm + 1x2.5 sqmm earth wire including taking down complete all as specified and/or directed by Engr-in-Charge.
Supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300 mm complete connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Note:- Old retreived exhaust fan has to be deposited to MES store.
All as per Ser item No 168 above, but in repairs.
Supply and laying XLPE insulated, aroured, heavy duty electric cables, with stranded aluminium copper conductor rating 1100 volts grading of size 70 sqmm 3.5 core laid in trenches or passing through pipes, ducts or fixed to walls / poles, complete all as specified and/or directed by Engr-in-Charge.
Supply and laying in replacement of XLPE insulated, aroured, heavy duty electric cables, with stranded aluminium copper conductor rating 1100 volts grading of size 16 sqmm 2 core laid in trenches or passing through pipes, ducts or fixed to walls / poles, complete all as specified and/or directed by Engr-in-Charge.
Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth, for foundation etc. or for shafts, wells cesspits, manholes, pier holes, etc. not exc 10 sqm on plan and not exc 1.5m in depth in any type of soil and getting out, complete all as specified and as directed.
Returning, filling in (soil), including spreading, levelling, watering and well ramming in layers not exc. 25cm, complete all as specified and directed by Engr in Charge.
Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified and directed by Engr in Charge.
M&L for Sand cushioning to under ground cables 8 cm below the cable before laying & 15 cm above the cable after laying, complete all as specified in clause 19.75 of SSR Part-I, 2009. Note : Punned thickness only will be measured and paid.
Supply and laying of factory made, machine pressed, unreinforced, pre-cast concrete cable cover class LV type-1 flat size 250 mm x 150 mm x 40mm, complete all as specified and directed.
S&F in repair electric water heater, storage type steel body with copper inner tank and heating element up to 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. Note:- Old retreived geyser has to be deposited to MES store.
Supply and fix in replacement LED street light fitting 35 Watt 230 Volt AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics with IP 65/66 protection complete all as specified and/or directed by Engineer-in-Charge.
S&F in repair 4 Way double door Tripple Pole Neutral vertical load line Distribution Board suitable for Flush mounting and suface mounting with 250 A copper bus bar with neutral bars and earth bars including MCCB 160 Amps TPN as incomer and SP/TP MCBs as outgoing and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.
M&L for Earthing complete with galvanised steel earth plate electrode 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to and including 4 mm dia GI wire as earthing lead, by means of bolts, nuts, check nuts and washers of galvanised iron all as shown in electrical plate No 3 of MES SSR Part I and testing on completion including excavation and earth work in any type of soil, PCC (1:3:6) type C1 chamber, MS frame and cover 6 mm thick in cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric or XPM (weight not less than 4 Kg per Sqm) with cast iron frame, funnel with wire mesh, GI watering pipe 20mm dia medium grade and lugs complete all as specified and/or as directed by Engr-in-Charge.
LEO TRADERS (BID ID -3481544)
R B TRADERS (BID ID -3467754)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.33 MB
TenderL16225263rdcall.pdf
Tender Documents • 1.19 MB
BOQ_825546.xls
BOQ • 3.83 MB
Download all tender documents and submit your bid