Renovation of Quarter No. P/4-SA (AandB) at Wimberlygunj

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. Columns. Plinth wall. Plinth wall (Var). For Septic Tank

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 20% of excavated earth. Varndah, Drawing room, Bed Room, Kitchen, Bath room, Toilet, Dinning room.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). Varndah, Drawing room, Bed Room, kitchen, Bath room, Toilet, Dinning room, Col, Plinth wall, Plinth wall (Var).

1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size). Plinth wall, Plinth wall (Var).

Centring and shuttering including strutting, propping etc. and removal of form work for : Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. Plinth wall, Plinth wall (Var).

Providing and fixing up to floor five level precast cement concrete hollow block including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)./1:1½:3 (1 Cement: 1½ coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). [40 x 20 x 15 cm- Outer, Front wall Drawing, Front wall bed, side wall, Window (W) TH, Window (W) DH, Door, Ventilator (V)]. [40 x 20 x 10 cm- Inner wall, Varndah, partion btwn draw & Bed, partion btwn Din &Kit, Partin btwn bath & Drw, Partin btwn Bed & Kit, Toilet, Bath, wall for cub board, wall for water tank].

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including

Providing cement concrete surface drain with 1:4:8 finishing with cement mortar 1:4, including floaoating cont. of neat cement in- side the drain on including top and exposed side including earth work excavation. 15 cm x 15 cm. Suface drain

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). Main Building Col., 2nd footing, 3rd footing, Short Column.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering. 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). Col, Plinth wall, Plinth wall (Var), Plinth wall For Over head Slab, Tie beam, Tie beam For Over head Slab, Lintel Beam ( Outer ), Lintel Beam( Inner)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)/.with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). Tank Slab, Shelf for kitchen, Shelf for cup board.

Centring and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete. Main Building Col., 1st footing, 2nd footing, 3rd footing, Short Column.

Suspended floors, roofs, landings, balconies and access platform. Tank Slab.

Shelves (Cast in situ). Cupboard

Lintels, beams, plinth beams, girders, bressumers and cantilevers.Plinth wall, Plinth wall (Var), Plinth wall For Over head Slab, Tie beam, Tie beam For Over head Slab, Lintel Beam ( Outer), Lintel Beam( Inner).

Columns, Pillars, Piers, Abutments, Posts and Struts. Main Building Col.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Cold twisted bars. Jali 10Q @ 0.15 c/c both ways, Col 12Q 4 Nos Main, Stirrups 8mm Q @15 cm c/c Main, Plinth Beam 12 mm Q 04 Nos, Plinth Beam 12 mm Q 02 Nos, Stirrups 8mm Q @15 cm c/c, Plinth Beam 12 mm Q 04 Nos, Plinth beam For Over head Slab, Tie Beam 12 mm Q 04 Nos, Tie For Over head Slab, Lintel Beam 10 mm Q 04 Nos, Lintel Beam( Inner), Slab Dist.Bar 10 mm dia, Slab Main Bar 12mm dia, K/Shelf 10mm @30 cm c/c, Dist. bar 8mmQ@112cmc/c, Cupboard 10 mm Q @ 20 cm c/c, Cupboard 08mmQ @12cm c/c.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Frame for door and window. Door (D), Door (D1), Door (D2), Window(TH) W, Window(DH) W1, Ventilator (V).

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws excluding, panelling which will be paid for separa. Second class teak wood, 35 mm thick shutters. Door (D), Door (D1), Door (D2), Window(TH) W, Window(DH) W1, Ventilator (V).

Providing and fixing M.S. grills of required pattern in frames of dowsetc. with M.S. flats, square or round bars etc. including iming coatwith approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. Windows,Ventilator and Gate etc.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size. Door (D), Door (D1), Door (D2), Window(TH) W, Window(DH) W1, Ventilator (V).

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm ( Front & back Door)

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150 x10 mm. Door (D), Door (D1), Door (D2)

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 100 x10 mm. Window(TH) W, Window(DH) W1, Ventilator (V).

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm. Door.

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 100 mm. Window, Ventilator.

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. Main Truss, 50 mm Q, Tie 50 mmQ, Support25 mmQ, Middile Rafter, 50 mm Q, Tie 65 mmQ, Support 25 mmQ, Jack Rafter, 65 mm Q, Tie 65 mmQ, Support32 mmQ, Porch, Purlin Main Bldg.40mmQ, Plate 20x20x8mm, Plate 25x25x8mm, Flat 40x6mm, Bolts & Nuts with washer

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Kitchen, Bath room, Toilet.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge hickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, rail and 115 mm wide provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick etc. complete as per dire. 30 mm thick pre laminated PVC door shutters.

Providing and fixing factory made P.V.C. door frame of size 50x47 mmwith awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. Kitchen, Bath Room, Toilet.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm. Varndah, Drawing Room, Bed Room, Dining Room, Skirting, Varndah, Drawing Room, Bed Room, Dining Room.

Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately) : White face insulating board. 12 mm thick, Varndah, Drawing room, Bed Room, Kitchen, Bath room, Dinning room.

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes. 75 mm diameter.

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes. 110 mm diameter.

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expan. Single tee with door. 110x110x110 mm.

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expan. Single tee without door. 75x75x75 mm.

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expan. Bend 87.5°. 75 mm bend.

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expan. Bend 87.5°. 110 mm bend.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any etc.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 0.05 % total coated thickness, Zinc coating 120gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 m. Ridges plain (500 - 600mm).

12 mm cement plaster of mix : 1:4 (1 cement : 4 fine sand). Front wall Drawing, Front wall bed, Side wall, Inner wall, Varndah, partion btwn draw & Bed, partion btwn Din &Kit, Partin btwn bath & Drw, Partin btwn Bed & Kit, Toilet, Bath, wall for cub board, Tank.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr / 10 sqm. Front wall Drawing, Front wall bed, Side wall, Inner wall, Varndah, partion btwn draw & Bed, partion btwn Din &Kit, Partin btwn bath & Drw, Partin btwn Bed & Kit, Toilet, Bath, wall for cub board.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work. Door (D), Door (D1), Door (D2), Window(TH) W, Window(DH) W1, Ventilator (V), Gate, Window,and Ventilator Grills

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040 mm bowl depth 250 mm

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe. 32 mm dia

Providing and fixing white vitreous china water closet squatting pan (Indian type). Orissa pattern W.C. pan of size 580x440 mm

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank.

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in- charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). "L" angle (2.5mm thick 11/2" x 11/2" ). varndah, Drawing room, Bed room, Kitchen, Bath room, Toilet, Dining room, Varandah. "T" (2.5mm thick 11/2" x 1" ).

Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer-in-charge.

Removing wood work in frames, trusses, purlins , rafters, weather boards, roofing including ridges, hips, valleys and gutters etc.and up to 10 metres span and 5 metres height including stacking the material within 50 metres lead :

Providing & Fixing of Polyethylene Septic tank 1000 mm to 2000 mm with Man hole Round Dim -310 mm ( 20-25 Flushing per day ) with its all fittings etc.

Whole Electrification works

Whole Plumbing works

T ABDUL BASHEER

R SELVAM

N H CONSTRUCTION

KANTI BALA

Abdul Gafoor

Haneefa Constructions

A SAMSUDDIN

A P HUSAINAR

M/S HABIB CONSTRUCTION

A Palani