REPAIR REPLACEMENT TO CERTAIN MISC BR WORK IN MARRIED ACCN IN DOMESTIC AREA UNDER GE AF JAMMU

Amount

Dismantling wall and ceiling board (fiber, pulp, PVC, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillets fixed with screws complete all as spd and directed.

S &F Exposed metal frame ceiling with 08MM thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600x8mm grid (Frame work for ceiling shall be measured and paid separately) complete all as spd and directed.

Supply and fixing Hollow PVC Wall Lining consisting of 5 to 6 mm thick colour/ printed PVC sheet including fillets ,fittings and fixture with all accessories etc as per approved design as.complete all as spd and directed by engr-in-charge

Supply and fixing Hollow PVC Ceiling Lining consisting of 5 to 6 mm thick colour/ printed PVC sheet including fillets,fittings and fixture with all accessories as per approved design,drawing.complete all as spd and directed by Engr-in-charge.

S&F Gl frame work (size of grid 605x605mm) for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed by Engr-in-charge.

Taking down cement plaster,existing wall tile/mosaic in any thickness including racking out joint hacking for key scrubing down with water etc complete all as specified.

M&L Vitrified Light/dark shade tiles double charge 9 to 10 mm thick (Square or rectangular ) polished , area of each tiles exc 0.42 sqm but n exc 1.00 sqm in wall/skirting with 10 mm thick cement mortar 1:4 to match the shade, pattern complete all as specified and directed by Engr in charge.

M&L Ceramic matte digital wall external tiles Light/dark shade 9 to 10 mm thick (Square or rectangular ) polished , size of each 300mmx600mm, in wall/skirting with 10 mm thick cement mortar 1:4 to match the shade, pattern complete all as specified and directed by Engr in charge.

M&L for 300x600 x7 mm thick glazed ceramic tiles of premium quality as in dado/ skirting and vertical surfaces set&jointed in neat cement slurry and pointed in colored cement over and incl 10 mm thick cement mortar 1:4 to match the Shade, pattern, laying at site complete all as spd and directed by Engr-in-charge.

Material and labour for 15 mm rendering in CM 1:6 on fair face of wall or on concrete surfaces finished even and smooth without using extra cement complete all as specified as directed by Engineer-in-Charge.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or over roof concrete surfaces mixed with integral water proofing compound finished even & fair without using extra cement upto the 4 th storey complete all as spd and directed by Engr-in-charge. Note : WPC shall be measured & paid seperately.

Supply only integral water proofing compound ISI marked complete all as spd and directed by engr-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed Notes:-Dismantled material should be thrown out of the defence line at govt approved dumping area.

M&L for colored non skid ceramic tiles 7to 8 mm thick, area of each tile exc 0.11 sqm but n exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement over and incl 15 mm thick screed bed or bedding layers of cement mortar 1:4 (including hacking of floors) to match shade, pattern, laying etc of tiles as directed at site complete all as specified and directed.

M&L Vitrified Light/dark/Highlighter shade tiles double charge 9 to 10 mm thick (Square or rectangular ) polished , area of each tiles n exc 0.36 sqm in floors in repair,set and jointed in neat cement slurry and pointed in colored cement over and incl 15 mm thick screed bed or bedding layers of cement mortar 1:4 (including hakcking of floors) to match shade, pattern, laying etc complete all as specified and directed by Engr in charge.

M&L Vitrified Light/dark/Highlighter shade tiles double charge 9 to 10 mm thick (Square or rectangular ) polished , area of each tiles exc 0.42 sqm but not exe 1.0 sqm , in floors in repair,set and jointed in neat cement slurry and pointed in colored cement over and incl 15 mm thick screed bed or bedding layers of cement mortar 1:4 (including hakcking of floors) to match shade, pattern, laying etc complete all as specified and directed by Engr in charge.

M& L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado,pillar and floor laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including Grinding blushing to achieve granite finish including moulding to exposed edges. complete all as spd and directed. Note:- The work should be executed in patch work & kota stone in steps should be provided in one piece with 2mm of groove.

Dismantling of, stone slabs and tiles of any description or any thickness in floors, aprons including screed bed or flooring etc complete all as specified and directed Notes:-Demolished material should be thrown out of the defence line at govt approved dumping area.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; all as specified and directed by Eng-in charge. Note:- Before execution of above mentioned item it is compulsary to make good the existing surface of PCC so that paver block could be fixed properly and no extra cost will be bourne by department.

M&L for Cemented tiles of size 30cm x 30xm x22mm thick (Designer tile flower type), machine pressed; set, jointed and pointed in net cement slurry in floors, and cut and polished with grey cement and color pigment, laid over 20 mm thick bedding layer of cement mortar 1:4 all as specified and directed by Eng-in charge Note:- Before execution of above mentioned item it is compulsary to make good the existing surface of PCC so that paver block could be fixed properly and no extra cost will be bourne by department.

M&L for Preparation of old surface of paver block,cemented tile and concrete surface including cleaning with wire brushes and mechanically and apply two coats of apex floor guard high performance floor coat emulsion,keep 8 hrs interval time in each coat.complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level).complete all as spd and directed. Notes:-Demolished material should be thrown out of the defence line at govt approved dumping area.

M&L PCC 1:2:4 type B-1(20 mm graded stone agg) as in copings, kneelers, apex stones,bed plates, kerbs and the like including weathering, slightly rounded or chamfered angles and throating, as directed etc complete all as spd and directed.

Taking down Chowkats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) complete all as spd and as directed. Note : including making good to disturbed surface with brick work,plaster,matching finishes to receive new frame or chowkhats and no extra cost will be paid to contractor against same.

Taking down chowkats or frames exc 1.5 sqm but n exc 4.0 sqm each with shutters (without taking off shutter from the frame).complete all as spd and direcetd. Note : including making good to disturbed surface with brick work,plaster,matching finishes to receive new frame or chowkhats and no extra cost will be paid to contractor against same.

S&F A Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45x85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F A Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F A Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge

S&F Factory made solid panel PVC door shutter 30 mm thick (style)Consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing of wire gauzed i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly complete all as spd and as directed

S/F solid PVC Door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, suppling & fixing in opening as per specification and drawing & all as specifed and as directed by Engineer-in-Charge..

S/F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specifed and as directed by Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F Aluminium anodised powder coating grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening including EPDM rubber, all complete as per requirement and direction of Engineer-in- charge.

S&F PVC roller not exceeding 40mm dia fixed to aluminium sliding window shutter with necessary clip or screw etc complete all as spd and directed

S&F for ACP Board of 12mm thickness to be fixed in aluminum partition frame including all necessary clip or screw etc complete all as spd and directed

S &F in repair 5.5mm thick, ordinary quality and glazing with rouber beading, joining cleat etc in square exc 0.5 sq. m in each pane complete all as specified and as directed bu Engr-in-charge.

S &F in repair 5.5mm thick, ordinary quality and glazing with rouber beading, joining cleat etc in squar n exc 0.5 sq. m in each pane complete all as specified and as directed bu Engr-in-charge.

S &F in repair 4.0mm thick, figured glass,pin headed type and glazing with oil putty in square n exc 0.5 sqm in each panel with rouber beading, joining cleat etccomplete all as specified and as directed bu Engr-in-charge.

Supply and fixing stainless steel wire cloth 0.63 mm nominal dia of wire and avg wide 1.40 mm aperture of tinned tacks of galvanised wire staple to steel windows/fixed with wooden beads of 2nd class HW to wooden doors/windows complete all as spd and direcetd.

S&F in repair Stainless steel barrel tower bolt of extruded section and fixed complete of Size 200 mm long complete all as specified.

S&F in repair Butt hinges 125mm size, extruded stainless steel with galvanised mild steel hinge pin,type B-21 complete all as spd and directed.

Supply and fixing in repair stainless steel sliding door bolts 250 mm long with hasp and staple (bold type) complete all as specified (ISI Marked) fixed in repair complete all as spd and directed.

S&F in repair stainless steel Handle cast type anodized of size 150mm complete all as specified.

S&F in repair stainless steel Handle cast type anodized of size 125mm complete all as specified.

S&F in repair Floor door stopper of stainless steel and toungue with hard drawn steel spring of 75 mm complete all as spd and directed.

Taking down or cutting MS helical door spring 150mm to 200 mm long by welding or chiseling etc from metal door frames and M&L in same position by running welding n. exc 6 mm thickness of metal and including fixing roller plate on wooden rail with screws complete all as spd and ditected by Engr-in- charge.

S&F in repair for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

Dismentling of wrought iron or mild steel work such as agle iron fencing post and similar type work or any description not other wise provided complete all specified and directed

M&L for Structural steel work (Ornamental and Special Design) in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed by Engineer-in- Charge. Note:- Pattern and design (Ornamental and Special Design) should be approved by GE and no extra cost will be bourne by department.

M&L for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165,including joing cleats and other necessary required items as per site.complete all as spd and directed by engr-in-charge and any type of ornament pattern and design as approved by GE. Note:- 1.Contractor shall not have any claim in respect of design/Ornamental shape/designer member,the differnece of rate and amount of desinger pattern will not be paid by Department.

M & L for providing and fixing stainless steel (Grade 304) railing,Gate made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc of required size, on the top of floor or the side of waist slab with suitable arrangement including joing cleats and other necessary required items as per site.complete all as spd and directed by engr-in-charge and any type of ornament pattern and design as approved by GE. Note:- 1.Contractor shall not have any claim in respect of design/Ornamental shape/designer member,the differnece of rate and amount of desinger pattern will not be paid by Department.

Dismantling of asbestos cement sheets,poly-carbonate sheet,corrugated or semi corrugated etc in roof covering.complete all as spd and direcetd.

S& F in repairs Pre-painted galvalume aluminium zinc coated corrugated sheet (including pre-laminated guard film) 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding in any shape (Curved shape or Plan Shape as per direction of GE and no extra payment will be paid to contractor against the same)/size as per user requirement to roof, wall, fixed with self tapping screws.complete all as spd and direcetd. Note:- 1.Contractor have to fixed the sheet upto 30 feet hight including necessory scaffolding or mechanically as per site requirement and no extra payment will be made to the contractor against the same.

S& F in repair 08 mm thick Poly-Carbonate UV protected hollow sheet with side lap fixed with coach screw and washer etc in roof, wall in any shape (Curved shape or Plan Shape as per direction of GE and no extra payment will be paid to contractor against the same)/size as per site requirement, fixed with self tapping screws.complete all as spd and direcetd. Note:- 1.Contractor have to fixed the sheet upto 30 feet hight including necessory scaffolding or mechanically as per site requirement and no extra payment will be made to the contractor against the same.

M&L preparation newly plastered surface of wall and Applying two coats of oil bound distemper over one coat of primer followed by 3mm wall care putty to achieve the surface even and smooth properly and upto the desired finish.complete all as specified and as directed by engr-in-charge.

M&L for preparation of new surface of walls and applying two coat of exterior emulsion/apex paint over a coat of primer incl filling gaps with wall care putty and applied using airless spray technology and capable of operating single spray gun with a suitable hose length the spray machine should be reputed manufacturer with pro guard technology and capability of tracking pressure as well as paint and primer usage including cleaning the floor, joinery, surfaces, usage complete all as specified and directed.

M&L for Preparation of new or previously untreated steel or steel based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L for injecting at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) 0.5 Litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same white cement complete all as specified and directed by Engineer-in-Charge. Note: Depth of hole will be measured for payment purpose only.

NOTE:- (A) SCHEDULE 'A' PART-II (Schedule of credit) Credit amount of Rs (Refer schedule of credit) for retrieved material mentioned in Sch 'A' Part-II of Tender documents in PDF form will be deducted offline during acceptance of tender of lowest bidder. (B) Group"A" Material to be used for the work. (C) Area surrounding to buildings should be cleaned of all debris & other fareign materials after completion of work & any damage done to the existing nearby structure, path, sewage lines manholes to repaired by the contractor without any cost.

M/S IMTESH BHAT (BID ID -3455723)

M/s Sunny Gupta (BID ID -3454882)

CCC (CHOUDHARY CONSTRUCTION COMPANY) (BID ID -3455444)