SPECIAL REPAIR TO MT COMPLEX AT AF STN AWANTIPUR

Amount

B/R PORTION

Dismantling floor hearth or wall tiling including cement mortor bedding (but not backing) removing serviceable tiles & rubbish of the premises complete.

M&L coloured/printed non skid ceramic tiles 7 mm thick (squre/rectangular) area of each tile exc 0.11 but not exc 0.18 sqm laid in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement, complete all specified and directed.

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of 450x300x7mm / 350x 250x 7 mm / 450X 350X 7mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, laid over and including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M&L 25mm PCC 1:2:4 Type B-0 (Using 12:5mm stone agg) as in sub base floor , complete all as directed and specified .

Demolition of cement concrete to ground floor(unreinforced) and paving n.exc 15cm thickness (below or above ground level) and removing rubbish of out side MOD land, complete all as specified and directed.

M&L Cement concrete work in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A'

Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'A'

Finishing surface of concrete roads, pavements, by brooming.

S&F in repair wire netting of nylon wire 2.00mm dia with 12mm size of mesh and fixed to roof ceiling and any area as specified, upto any height for bird proofing with all necessary arrangement complete all as specified and directed by Engr-in-charge

Dismentalling of plain or corrugated steel sheeting of any gauge, thickness etc in roof coverings/cladding/eave etc complete all as specified.

S&F galvanised corrugated mild steel sheeting, with two corrugation side lap fixed with 'L' type or 'J' type or cranked hooked bolts with washers in roof, 0.63mm thick, grade-O quality, with 120 grms/sqm zinc coating and grade 'B' Class 8 complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised plain mild steel sheeting 0.63mm thickness fixed with 'L' type or 'J' or cranked hook boltes with washers, in roofs as in ridge etc all as specified and directed.

Refixing Plain or corrugated steel sheeting, any gauge, thickness, roof coverings with two corrugation side lap fixed with L' type or 'J' type or cranked hooked bolts and dome type bitumen washers complete all as specified and directed by Engineer-in-Charge. Note:-serviceable sheets obtained under item No 11 above shall be re-used.

Demolition of brick or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone works and precast concrete articles, complete all as specified and directed

M&L Brick work with sub class B bricks ,straight or curved on plan exc 6m mean radius built in CM 1:6 Complete all as Specified and directed.

Taking down Cement Plaster, any description on Brick Walls or on Concrete Surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc, and removing same from the Site(s), complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of concrete/brick interior surfaces in cement mortar 1:6 as per manufacturer's instruction, finished fair and even without using extra cement complete all as specified and directed.

M & L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 on wall surfaces, finishing the surface even and smooth without using extra Cement complete all as specified. Note:- Intgral water proofing compound shall be measured and paid for separately.

M & L 100 mm thick PCC (1:3:6) type C-2 using 40mm graded aggregate as in flooring even and smooth without using extra cement complete all as specified and directed.

M&L for Plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in benching for manholes, bands , coping , bed plate etc. with slightly chamfered or rounded angles including necessary form work, if any required, and finishing exposed surface even and smooth without using extra cement, complete all as specified and as directed.

M&L preparation of newly plastered wall surface and applying of Birla/JK white wall putty approx 3 mm thick as per manufacturer's instruction and make the surface smooth by rubbing with sand papers and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and directed.

Preparing new plastered or un-plastered surfaces of walls and applying two coats Acrylic exterier emulsion paint in camouflaging (Disruptive) pattern (Green, Grey & Brown colour) over a coat of acrylic primer complete all as specified and directed. (Make:Asian/Berger/Nerolac/ICI/Shalimar/Garware/Johnson).

Preparation of new surfaces of steel or iron work or CGI/ PGI sheeting in walls or roofing, over 10cm width or girth, not otherwise described and applying two coat of synthetic enamel paint in camouflaging (Disruptive) pattern in three colours (Green, grey and brown) over a coat of acrylic primer complete all as specified and directed. Make : Asian/ Berger/ Nerolac/ ICI/ Shalimar/ Johnson

Preparation of old painted surfaces of steel or iron work or CGI/ PGI sheeting in walls or roofing, over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint in camouflaging (Disruptive) pattern in three colours (Green, grey and brown), complete all as specified and directed. Make : Asian/ Berger/ Nerolac/ ICI/ Shalimar/ Johnson.

Preparing old plastered or un-plastered surfaces of walls by scraping the surfaces, brooming down or steel wire brushing down smoke soot, mould, moss and efflorescence salts and trading oil and greasy spots etc and applying one coat of exterior acrylic emulsion paint in camouflaging (Disruptive) pattern in three colours (Green, grey and brown), complete all as specified and directed. Make: Asian/ Berger/ Nerolac/ ICI/ Shalimar/ Johnson.

M&L for Complete removal of existing treatment of old decorated plastered or un plastered surfaces of wall and applying two coats of Acrylic washable distemper over a coat of primer , complete all as specified and directed.

S&F in repair PVC flushing cistern 10 ltr capacity white with all internal fittings including brackets PVC connection 45cm long including nut and PVC washer at both ends including 32mm bore PVC long bend flush pipe 90cm long complete all as specified and directed.

S & F Vitreous china wash hand basin coloured, flat back type of size 550mm x 400mm including waste pipe & plug, porcelain stopper, 32mm dia PVC waste pipe with CP brass coupling and set of bracket complete all as specified and directed.

S&F in repair Vitreous China wash down water closet (pedestal pattern), White/coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and chromium plated jet including PVC connection, fixed complete including demolition of old unservicable WC and provision of plain cement concrete M-15, type B-I, using 20mm graded crushed stone aggregate, fixed in repairs complete all as specified and directed.

S&F in repair Vitreous China urinals of minimum size 580x380x350 mm, crystal white, HALF STALL URINAL, with 32 mm bore waste fittings, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including spreader, 60mm long brass screws, pointing around urinal back in cement with brackets, flush pipe, trap, grating and Union for discharge pipe. (Including fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

Taking down chowkhats of frames of any description n.exc 1.50 sqm with shutters (without taking off shutters from the frames) and making good disturbed portion complete all as specified and directed.

Taking down shutters of any description exc. 1sqm and not exc. 2 sqm each, complete all as specified and directed.

S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube supply and fixing as specification and drawing.

S&F of factory Made Solid panel PVC door shutter, 28 to 30mm thick (stiles) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded and wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheetb eadingplain colour PVC sheets for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling and fixing in the frame at site as per specification & drawing.

S & F Factory made Glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass/gauze etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); in second class hardwood, Complete all as specified and directed by Engineer-in-Charge

S&F 35 mm thick Second class hard wood factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated as directed by Engineer-in-Charge.

Supply and fixing Butt hinges, (ISI Marked), aluminium alloy with galvanised mild steel, of size 100mm long all as specified & directed.

S&F 125 mm long stainless steel butt hinges medium weight with stainless steel screw complete.

S&F extruded aluminum alloy handles of size 100mm fabricated type anodised complete.

S&F extruded aluminum alloy handles of size 150mm fabricated type anodised complete.

S&F extruded aluminum alloy handles of size 125mm fabricated type anodised complete.

S&F Aluminium alloy anodised barrel tower bolts of extruded section 150 mm long and fixed complete.

S&F Aluminium alloy anodised barrel tower bolts of extruded section 200 mm long and fixed complete.

S&F Aluminium alloy anodised barrel tower bolts of extruded section 100 mm long and fixed complete.

S&F Aluminium alloy, anodised, sliding door bolt size 200mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring 150mm long complete all as specified and directed.

S&F Anodised aluminium frame for doors,windows and ventilator with one or more rebates including joining cleat for fixing etc. complete all as specified

Anodised aluminium window and ventilator shutters, fixed type without sash bars, aluminium sections weighing of 0.55 kg/RM including fixed with alumnium beading, silicon lining and gaskets,necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed

S&F anodised aluminium door shutters, aluminium section weighing 1.10kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

4.8 mm thick sheet glass, ground or obscured or frosted/ tinted and glazing with oil putty or fixed with bead/glazing pins in squares of exe 0.5 sqm in each pane all as specified and directed.

S & F Anodised aluminium grill (anodised transparent or dyed to requiredshade according to IS: 1868 with minimum anodic coating of gradeAC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge

S&F of galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks, or galvanized wire staples all as specified & directed.

M&L for 12 mm prelaminated particle board both side decorative, fixed with aluminium beading and rubber neoprene packing to aluminium frame

3mm thick sheet glass, ordinary type and glazing with oil putty or fixed with bead/glazing pins in squares size n.exc 0.5 sqm in each pane including hacking out old broken glass (any thickness, size quality or description) all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets on any description, any thickness, including cover fillets.

M&L for prelaminated particle board 12mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination with all around 6mm thick teak wood beading as in cup board shutters, shelves,palmet boxes etc, fixed to timber frame complete all as specified

Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for preparing of new or previous untreated steel surfaces over 10cm width or girth and making good including primer and make the surface smooth by rubbing with sand papers etc and applying two coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing of old painted steel surfaces over 10cm width or girth and making good with & including by necessary red lead putty and make the surface smooth by rubbing with sand papers etc and applying one coat of synthetic enamel paint on old prepared surfaces of steel complete all as specified and directed.

Preparation of new wooden surfaces of any description not otherwise described, over 10 cm width or girth and providing two coat of synthetic enamel paint over one coat of pink primer all as specified & directed.

S&F PVC SHEET WALL PANELLING of thickness 5mm consisting of panels of desired size stuck on inner frame work of 50mm wide strips of 5mm thick prelam PVC sheet. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. A groove of 2mm may be left at the joint of two panels for aesthetic looks. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a U Channel at top, bottom and side edges and strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement complete all as specified and directed ( Note- Including all nesscesary fittings and scafolding for heighted site)

Taking up or down 15 mm dia steel tubing in wall, ceiling or floor and connections,including cleaning for refixing or removal to store etccomplete.

S&F 15 mm dia medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors.

Cutting chases,pinning for concealed water tubing and making good to facing where required and pointing in cement mortar 1:3 ,cutting exc 10cm but n.exc 20cm girth all as specified and as directed.

S&F in repair 20mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rails 20mm dia D type 60cm long between flanges with chromium plated bracket and fixed all as directed.

S&F 500 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical double layered with closed top) duly provided with necessary fittings/ fixtures for connecting inlet, outlet, washout and overflow pipes; hoisted and fixed in position incl dismantling PVC water sotrage tanks of capacity more than 250 to 500 litres capacity complete all as specified and directed.

S&F in repair 15 mm bore CP Bib tap cast copper alloy fancy type crutch or butterfly handles screwed down for iron or for brass ferrule complete.

S&F in repair stop valve/angle valve,fancy type, chromium plated, cast copper alloy screwed down,high pressure, with crutch or butterfly handle of 15mm dia. Screwed both ends for iron pipe or for unions and fixed. all as specifid & directed.

S&F in repair Brass CP central hole wash basin mixer for hot & cold for 15mm dia complete fixed to connection as specified and directed.

S&F PVC (SWR) pipes single socketed,75mm bore, in any length with rubber ring joints fixed to wall and floor, complete all as specified and directed.

PVC (SWR) 75mm bore (dia), Bends, any radius with access door and Jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as directed.

M&L PVC (SWR) floor trap 75 mm dia including jointing with solvent cement complete.

Taking down shutters of any description area exc 2.00 sqm each all as specified & directed.

S&F Steel rolling shutters tickness of lath 1.25mm thick with out ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer; erected in position as indi cated, complete: push pull or gear operated type with bevel gear box & crank handle complete all as specified and directed by Engr-In-Chagre.

E/M PORTION

Taking down copper/aluminium point wiring(light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials and making good disturbed surfaces of walls, floors, etc.

Taking down DB TPN/SPN 4/8/12 Way 415 Volt/240 Volt including MCB/MCCBs.

Taking down light fittings of any type complete all as directed .

Taking down old aluminium sub main wiring of any size.

M&L for Point wiring complete as specified with 1100 volt grade 1.5sq.mm. (nominal area) single core PVC FRLS insulated unsheathed cable multi-stranded copper conductor drawn through and including rigid non-metallic PVC conduit of suitable size but not less than 20mm dia , with all fittings, fixed on concealed along with necessary metal flush boxes of required module mounting for modular fittings in the wall suitable for housing modular pattern switches/ sockets/ regulators etc. duly earthed with same cable size FRLS type as for wiring above but green in colour as continuous earthing wire complete all as specified for :- (a) One light /fan/bell point controlled by one nos, one way 5/6 Amps switch.

One 3/5 pin Modular type socket outlet, 5/6 Amp on the same board controlled by one nos, one way switch.

One 3/5 pin modular type socket outlet, 5/6 Amp, independent controlled by one nos, one way switch.

All as per item No 84.00 above but point wiring for 5/15A modular socket outlet with 2.5 sqmm PVC FRLS insulated multistranded copper conductor and one run of 2.5 sqmm cable for earth in green colour complete all as specified and as directed by engr-in-charge.

S&F in replacement of modular piano type switch one way one module, SP, flush type, 5/6 Amps, 230 volts AC, 50 Hz complete all as specified.

S&F in replacement of modular piano type socket outlet flush type 2 module, 5 pin, 5/6 Amps, 230 volts AC, 50 Hz, multipurpose type complete all as specified.

S&F in replacement of modular piano type switch one way one module, SP, flush type 15 Amps, 230 volts AC, 50 Hz complete all as specified.

S&F in replacement of modular piano type socket outlet flush type 2 module, 5 pin, 5/15 Amps, 230 volts AC, 50 Hz, multipurpose type complete all as specified.

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLS cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non-metallic PVC conduit of suitable size but not less than 20mm dia , with all fittings, fixed on concealed in wall complete with making good the wall surface with plastering and painting after point wiring as required on site and as specified and directed with all connected accessories including one single core multistranded PVC insulated, unsheathed, FRLS type, 1100 volts grade, 1.5 sqmm copper conductor cable as earth continuity cable including pressed steel terminal boxes made out of MS sheet not less than 1.2mm thick duly painted with one coat of red oxide primer with 3mm thick laminated sheed cover for mounting of switches, socket, for One light controlled by one switch complete all as specified and as directed. (a) One light /fan/bell point controlled by one nos, one way 5/6 Amps switch.

One 3/5 pin socket outlet, 5/6 Amp, independent controlled by one nos, one way switch.

All as per item No 90.00 above but point wiring with 2.5 sqmm PVC FRLS insulated multistranded copper conductor and one run of 2.5 sqmm cable for earth in green colour complete all as specified and as directed by engr-in-charge.

S&F in replacement of piano type switch socket combination flush type, 2 in 1 , 6 Amps flush type, 230 volts AC, 50 Hz, multipurpose type complete all as specified.

S&F in replacement of piano type switch socket combination flush type, 5 in 1 , 6/16 Amps, 230 volts AC, 50 Hz, multipurpose type complete all as specified.

S&F Piano type switch , Flush type single pole, one way 6 amps

S/F Ceiling rose PVC polycarbonate , isolated body 3 terminals 230 V complete.

Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp.

S&F in replacement of LED bulk head light fittings of capacity 13.5 W weather proof, anti corrosion wall/ceiling mounted opel colour decorative, round shape with PC cover including 3 core conductor cable for connection complete with all accessories all as specified..

S & F surface mounted 40 watts LED tube light fitting 220volts AC decorative box type with driver holder incliuding LED tube light connecting up with 3core flexible copper conductor cable of suitable size from ceiling rose complete. Make: Havells/Bajaj/Phillips/Crompton

Supply and fixing LED light fitting mirror type with high output diffuser 2 feet, 10 watts 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete as directed. Make: Havells/Bajaj/Phillips/Crompton

Supply and fixing LED bldg security light light fitting 100 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply and fixing GI Bracket bent to shape fabricated with GI Pipe 40mm dia light grade 1.5m long including mounting clamps nut bolts complete all as specified and directed.

S & F Sub main wiring with PVC insulated cable 2 single core 4 sq mm 1100 V grade with stranded copper conductor in and incl PVC conduit ISI marked not less than 20mm dia concealled in wall complete with making good the wall surface with plastering and painting after point wiring incl all specials like joint elbow, Tee ,junction , bend etc and provision of PVC insulated copper conductor single core 4 sq mm for earth continuity all as directed.

S & F Sub main wiring with PVC insulated cable 2 single core 6 sq mm 1100 V grade with stranded copper conductor in and incl PVC conduit ISI marked not less than 20mm dia concealled in wall complete with making good the wall surface with plastering and painting after point wiring incl all specials like joint elbow, Tee ,junction , bend etc and provision of PVC insulated copper conductor single core 6 sq mm for earth continuity all as directed.

S&F in replacement of factory VTPN DB double door made out of CRCA mild steel sheet with insulating material like polyester epoxy quoted surface mounting 4 way TPN 415 volts, vertical type, surface mounting with suitable busbar, neutral link & earth link suitable for MCCB TP as incomer & MCB SP/TP as out going complete including MCCB 63-100 A four pole breaking capacity 15 kA for incoming complete all as specified.

S & F Single pole and neutral sheet steel powder coated vertical type Double door Distribution board for MCCB/MCBs fitted with 200 Amps rated bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply SP&N DB system 8 ways. Make: Legrand/L&T/Havells/ABB

Supply and fixing amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of Single pole & Neutral and current carrying capacity 32 Amps in the MCB DB complete with connection testing and commissioning.

Supply and fixing amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of Single pole and current carrying capacity 6 to 32 Amps in the MCB DB complete with connection testing and commissioning.

Supply, laying or passing through pipe underground cable PVC sheathed, XLPE insulated armoured LT 1100 volts grade with aluminium conductor of size 35 Sqmm, 4 core including making electrical connection with thimbles complete all as specified.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for laying of cables or other items and getting out soil in soft/loose soil complete all as specifed.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm complete all as specified.

Removing excavated material not exceeding 50 mtr and depositing where directed in a level not exceeding 1.5 mtr above the starting point of any type of soil complete all as specified.

M&L for sand cushioning to under ground cable provided with a layer of sand 8 cm depth before laying of cable and 15 cm depth after laying and stretching the cable all as specified. Note: Punned thickness of sand shall be measured & paid.

M&L for well burnt sub class 'B' bricks of nominal size 230X115X75 mm abutting each other for mechanical protection of cable with width equal to lenght of brick complete all as specified.

M&L for cutting of bitumen road/PCC road/hard standing for laying of GI pipe and passing of cable including making good to disturbed surface with PCC 1:4:8 and matching with existing surface complete all as specified.

Supplying and laying GI tubing light grade of size 50 mm bore for cable protection complete all as specified.

Earthing complete with galvanised earth plate electrode 60 cm x 60cmx 6.0 mm thick, buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the earth plate not less than 1.5m below ground level , connected to GI earth wire 4 MM Dia through GI pipe "light Grade" as earthling lead by means bolts and nuts check nuts and washers of galvanized iron and connected to main switch board including watering arrangement with PCC chamber , MS funnel with wire mesh,. CI cover with frame etc including necessary excavation in any type of strata , returning, filling removal of soil outside MD land ,filling of charcoal and salt complete all as shown in electrical plate No. 3 of MES Sch Part I , connected to Earthing test point all as specified and directed on testing on completion.

Earthing complete with galvanised earth plate electrode 60 cm x 60cmx 6.0 mm thick, buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the earth plate not less than 1.5m below ground level , connected to GI strip 25X4 mm size as earthling lead by means bolts and nuts check nuts and washers of galvanized iron and connected to main switch board including watering arrangement with PCC chamber , MS funnel with wire mesh,. CI cover with frame etc including necessary excavation in any type of strata , returning, filling removal of soil outside MD land ,filling of charcoal and salt complete all as shown in electrical plate No. 3 of MES Sch Part I , connected to Earthing test point all as specified and directed on testing on completion. Note : On testing after complition of earthing, if desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own expense and risk to the entire satisfaction of engr-in-charge

M/S ABBAS M. ENTERPRISES (BID ID -3295736)

M/S LATIF AHMED MIR (BID ID -3293481)

M/S SK ATLANTIC ENTERPRISES (BID ID -3296135)