Establishment of Administrative Building with laboratory, Kennel for Male and Female Dogs and Water supply arrangements for Regional Centre for Conservation of Native Dogs in Pavoorchathiram at Tenkasi District

Amount

Civil Works

Earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in hard rock requiring blasting inclusive of shoring strutting and baling out water wherever necessary refilling the sides of foundation with excavated earth in layers of not more than 15cm thick well rammed consolidated and depositing the surplus earth with in the compound in places shown by the departmental officers within an initial lead and lift and clearing, levelling the site etc., complete complying with standard specifications.

Supplying and filling in foundation, basement, etc with filling Stone dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five M.sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Refilling in foundation, basement, etc with excavated earth in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling of gravel by lorry in basement filling including conveyance loading and unloading charges and all other incidential charges filling laying watering and consolidation etc., complete as directed by the Dept., Officers with standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) For square or rectangular colums, boxing top and bottom slab, sill slabs, sunshade facia, fins and drops etc.,

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) For slabs, rectangular Tee or Eill beams, lintels, staircase waist and landing salbs, landing beams, loft slabs, canopy slabs, beams etc.,

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) For Curved Vertical Surface.,

Reinforced Cement Concrete 1:11/2:3 (One Cement, one and half M.sand and three hard broken stone jelly) using machine broken 20 mm gauge hard broken granite stone jelly for all RCC item of works excluding cost of reinforcement grill, fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrator, finishing, curing, etc., complete and providing fixtures like fan clamps in the RCC floor/roof slab wherever necessary and bearing surfaces of wall, beam etc. shall be finished smooth with cement mortar 1:3 (One Cement and Three P.Sand) 12mm thick and kraft paper laid over it without claiming extra, etc., complete complying with standard specification as directed by the departmental officers. For foundation and basement

For superstructure in Ground floor

From 3.00m to 6.00m height above Ground Level

From 6.00m to 9.00m height above Ground Level

Reinforced Cement Concrete 1:2:4 (One Cement, two M.sand and four hard broken stone jelly) using machine broken 20 mm gauge hard broken granite stone jelly for all RCC item of works excluding cost of reinforcement grill, fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrator, finishing, curing, etc., complete and providing fixtures like fan clamps in the RCC floor/roof slab wherever necessary and bearing surfaces of wall, beam etc. shall be finished smooth with cement mortar 1:3 (One Cement and Three P.Sand) 12mm thick and kraft paper laid over it without claiming extra, etc., complete complying with standard specification as directed by the departmental officers. For foundation and basement

For superstructure in Ground floor

Supplying, fabricating and placing in position of steel reinforcements using MS / RTS rods for all RCC works as per design given including cost of steel. Binding wire, straightening the rods, welding of rods, dia above 25mm in all floors complying with standard specifications. [The welding should conform to BIS. Wherever required at contractor’s expense.]

Brick work in Cement Mortar 1:5 (One cement and Five M.sand) using second class ground moulded chamber burnt bricks of size 9”x 4½”x 3” for the following including curing, etc., complete complying with standard specification For foundation and basement

For superstructure in Ground floor

Brick partition walls of 11.50cm thickness using best quality II class ground moulded chamber burnt bricks of size 9" x 4-1/2" x 3" in Cement Mortar 1:3 (One Cement and Three M. Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately) For Foundation and Basement

For superstructure in Ground floor

Plastering with Cement Mortar 1:5 (One cement and Five P.sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three P.Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Paving the floor with Designed Colour double charged Vitrified tiles of size 60 x 60 x 8mm in all floors over a base layer of Cement Mortar 1:3 (One cement and three M.sand) 20mm thick and pointed with white cement mixed with colouring pigments at the rate of 0.3 Kg/sq.m including finishing neatly and curing, etc. complete, complying with standard specification and as directed by the departmental officers. (The basic cost of tiles should not be less than Rs.80/-- Sq.ft)

Flooring with the Eurocon tiles of size 300mm x 300mm laid over cement mortar 1:3 (One cement and three sand) 20mm thick and pointing the joints to full depth of slabs with cement mortar 1:3 (One cement and three sand) mixed with colour oxide including laying, finishing, polishing with machine polish, curing etc., complete complying with standard specification

Supplying and fixing with anti-skid step tiles of size 300 x 300 x 25mm with 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three M.sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the engineer,i/c., before use on works)

Supplying and paving the floor with design mat finished ceramic tiles of approved brand and quality of size 305 X 305 X 6mm in all floors over a base mortar using cement mortar 1:3 (One cement and three M.sand) 20mm thick laid in situ true to alignment and pointed with colour cement (White cement mixed with colouring pigment) to suit the colour and shade of the ceramic tiles used neatly and fixed in position without any air gap in between the ceramic tiles etc., complete complying with standard specification and as directed by the departmental officers. (The sample colour and shade of the ceramic tiles should be got approved from the departmental officers before use on works).

Dadooing walls with best approved quality, printed design colour glazed tiles of size 300 mm x 450 mm x 6 mm sizes set in Cement Mortar 1:2 (One Cement and Two M.sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers

Painting two coats of newly plastered wall surface with ready mixed exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive engineer before use of work).

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Engineer,i/c., before use on works).

Supply and fixing country wood scantling (first quality wood) for door frames including labour charges for making, applying anti corrosive paint on the back sides of frame and fixing the frame in position, etc. complete complying with standard specification. (The wood have to be got approved by departmental Engineers before use on work).

Supplying and fixing flush door shutters 35mm thick of single leaf with skin type paneled door made up of hard wood of approved quality including fixing necessary furniture fittings such as iron oxide MS hinges of 125mm x 30mm size 3 Nos., aluminium aldrop of size 250 x 16mm – 1 No. aluminium tower of size 250 x 12mm – 1 No. Aluminium tower bolt of size 200x12mm – 1 No., D type aluminium handle of size 125mm – 2 Nos. Aluminium door stopper / magnet catch 3” depth – 1 No. respectively, etc. complete complying with standard specification.

Supplying and fixing of country wood (first quality Paddock) paneled door of double leaf using first class Country wood. The vertical styles will be 120mm x 38mm and top rail will be 250mm x 38mm bottom rail and middle rails will be 200mm x 38mm including cost of furniture fittings like oxidized iron butt hinges of size 125 x 30mm - 6 Nos., Aluminium tower bolt of size 250x12mm – 2 Nos., Aluminium tower bolt of size 200 x 12mm - 1 No., Aluminium aldrop of size 250 x 16mm - 1 No. to be fixed with 40mm bolt, etc. D type aluminium handle of size 125mm – 3 Nos. Aluminium door stopper / magnet catch 3” depth – 2 Nos. respectively, etc. complete complying with standard specification. (Wood shall be Paddock or its equivalent)

Supplying of MS hold fasts of size 330x50x6mm MS flats suitably folded to the rejoined ‘Z’ shape to have two end flabs 50mm long and over all length of the horizontal position as 230mm and including making necessary groove in the two end flats to accommodate screws etc complete

Supplying, fabricating and fixing in position standard pristine white U-PVC (Un-Plasticized Polyvinyl Chloride) partly fixed and partly sliding windows as per the design and drawings and making necessary opening for the exhaust fan fixing in all floors with extruded UPVC sections of required sizes as per IS standard with necessary accessories such as rubber beedings with best quality rubber, lock, handle, supplying and fixing 4mm thick plain / frosted glass including the cost of all materials, labour, power consumption required for the fabrication, drilling holes in RCC columns, floor, mansory wall wherever necessary with power drills to the required extent and making good to the original condition after fixing etc., and as directed by the Engineer,i/c.,

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI / 1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the departmental Engineer,i/c., before use on work.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) doors the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI / 1mm 125 GSM and 100% corrosion free, the profiles are multi-chambered sections with all thick of 2mm. The FPDM rubber covered with over all the edges of frame and shutter the shutter will be provided with ESPAG multi power point locks and also handle to be provided. The corners and joints should be welded and cleaned. Strong locking systems and as per size for arresting noise and energy loss. The door should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The door should be got approved from the Executive Engineers before use on work.

Supplying and fixing of M.S.grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification.

Supplying and fixing 50mm dia (2mm min tickness), MS tube hand rails with balustrade and horizontal rails as per design and drawings including floor flange ,anchor plate, grouting, welding and grinding etc., Running length of mild steel hand rail will only be measured for payment) etc., complying with standard specification and as directed by the departmental officers

Supplying and fixing in position best approved ISI quality PVC Rain water down fall pipes of 110mm dia meter having working pressure of 4Kg/Cm2 including cost of PVC pipe, with necessary shoes, bends, nails, teakwood plugs, screws etc., and fixing of cost iron gratings of required dia meter and special clamps at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cost of brass screws, teakwood plugs to be used shall be 150mm X 25mm in front and 200mm X 75mm in rear and all other sides to a depth of 100mm. The PVC pipe shall be fixed with teak wood plugs by means of “U” clamps using brass screws. Special types of “U” clamp at the centre of the pipeline shall be fixed in addition to those for more than 3 meter pipe length complying with standard specifications.

Supplying and fixing in position by means of 75 mm long and 65 mm dia counter sunk bolt and nuts embedded in the floor with rubber or fiber washer white glazed European Water Closet white colour with 100 mm "P" trap with double flapped rigid PVC black seat and seat cover with C.P. brass hinges including supply and fixing 10 litres capacity PVC low level flushing tank with a pair of C.I. brackets, etc., complete with all fittings such as 15 mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40 mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15 mm brass connections, 15 mm G.M. wheel valve, 15 mm brass nipple (2 Nos.), 15 mm nylon connection and fixing the low level ISI marked flushing tank with T.W. plugs and screws and giving necessary connection to the CI / PVC pipe including cost of 600 mm length of 100 mm dia C.I. Pipe and painting the C.I. Brackets with 2 coats of approved paint over one coat of red oxide primer and redoing the dismantled masonry to original condition etc. complete. (The EWC and flushing tank should be got approved by the Executive Engineer before use on works: Make: Parry ware / Hind ware or its equivalent))

Supplying and fixing in position CP Two way bib cock with Health faucet of best approved quality and approved make etc.,complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Providing & fixing first quality white vitreous china oval / round / square wash basin (size as per architectural drawing) for under counter mounting, specially fabricated CI / MS brackets, painted with two or three coats of enamel paint of approved shade over a coat of primer, 32 mm CP brass waste and CP brass cast bottle trap and pipe to wall with CP brass flange and rubber adopter for waste connection complete including filling gap between counter and wash basin with approved type poly sulphide sealant, cutting and making good the walls wherever required. Vanity counter top type. (rate including the granite counter, size as per drawing and RCC slab wherever necessary)

Supplying and fixing C.P. wall mixer 2 in 1 with over head Shower Rose with arm of approved make and best quality including labour charge for fixing and finishing, etc. complete complying with standard specification.

Supplying and fixing in position best quality brass chromium plated towel rail of 600mm length 20mm dia with CP brackets of same materials including fixing with necessary T.W. plugs, brass C.P. screws and dismantling masonry etc., complete with standard specifications. (The towel rail should be got approved by the Departmental officer before use on works).

Supplying and fixing in position 15 mm dia C.P. long body tap (Heavy type) of approved make conforming to IS specification and quality including cost of shellac, thread, etc., complete, complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Departmental Officer before use on the works)

Supplying and fixing in position 15 mm dia C.P. Screw down tap (Heavy type) of approved make conforming to IS specification and quality including cost of shellac, thread, etc., complete, complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Departmental Officer before use on the works)

Providing and fixing CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11 (operating pressure - 7 Bar @ 82 Deg C and 28 Bar @ 23 Deg C)for pipes from 1/2 Inch to 2 Inch. Pipe to be used from 2-1/2 Inch to 6 Inch. Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers, Unions, Reducers, brushings etc. including transition fittings (connection between CPVC & metal pipe/GI) i.e. Brass Adaptors (both Male & Female threaded) conforming to ASTM D-2846. ASTM F441 with only CPVC solvent cement conforming to ASTM F-493.Cost shall be inclusive of (a)Making maximum of 7.5 x 7.5 cm chasing in wall and floors for the pipe, making good the same by using 1:1 cement mortar over the wire mesh and providing protection to embedded pipes and fittings (in wall chase) by wrapping two layers of 400 micron polythene sheet including proper overlaps on joints complete as required or (b) Fixing/supporting the pipes (& fittings) at wall/ceiling level supported by galvanized clamps, hangers etc, as per specification. Exposed pipes to be painted of legends with direction arrow. GI pipe sleeves suitable higher size shall be provided wherever the pipes are crossing the fire rated walls / floors slab and sealing the sleeves with glass wool in between and fire sealant compound at either end all as per Project Manager's / Consultant requirement. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings. (Higher Pressure rating with higher pipe thickness) standard dimension Ratio - 11. 20mm dia CPVC pipe

25mm dia CPVC pipe

32mm dia CPVC pipe

Supplying, laying and jointing UPVC pipe (Schedule-40) of the following dia of approved quality and best variety and laid properly to alignment including fixing the required specials lent excluding cost of such specials but including cutting, threading and fixing to the wall with necessary clamps, screws, teak wood plugs making holes in the wall (or) drilling holes in the roof and making good the disturbed portion to the original condition with necessary brick work and plastering etc., complete complying with standard specifications. (The UPVC pipe should got approved by the Engineer,i/c., before use on work). 40mm dia UPVC pipe (Schedule - 40) - Above Ground Level

Supplying, laying and jointing UPVC pipe of the following dia of approved quality and best variety and laid properly to alignment including fixing the required specials lent excluding cost of such specials but including cutting, threading and fixing to the wall with necessary clamps, screws, teak wood plugs making holes in the wall (or) drilling holes in the roof and making good the disturbed portion to the original condition with necessary brick work and plastering etc., complete complying with standard specifications. (The UPVC pipe should got approved by the Engineer,i/c., before use on work). 50mm dia UPVC pipe - (Schedule - 80) - Below Ground Level

Supplying and fixing in position best quality PVC soil waste pipes of various size having ISI mark and pressure of 6 Kg/Sq.cm providing leak proof joints with PVC adhesive etc. including fixing to the walls with necessary T.W. plugs, brass screws mild steel clamps etc. and giving connection to the sanitary fittings including dismantling brick masonry /RCC works / roof slab etc. wherever necessary and making good the dismantled portion to the original condition, complying with standard specifications etc. complete (The PVC pipe should be got approved by the Departmental Officer before use on works).- 75mm dia pipe 6 Kg / Cm2 with ISI mark

110mm dia pipe 6 Kg / Cm2 with ISI mark

Providing and fixing in position 100mm PVC .Multi inlet Floor traps with CP grating, joining, embedding in concrete etc. complete rate to include making of opening in floor, marble / tiles, for fixing grating. Size 100 mm x 75 mm floor trap

Providing inspection chambers of various sizes using 9” thick brick walls using second sort table moulded chamber burnt bricks of sizes 9”x 4½”x3” in Cement Mortar 1:3 (One cement and three sand) 12mm thick and outside surfaces in C.M. 1:5 (One cement and five sand) 12mm thick. A precast cover slab of 75mm thick shall be provided for the chamber. The rate includes necessary earth work excavation to the required depth, Plain Cement Concrete 1:5:10 (One cement five sand and ten aggregate) 75mm thick etc., complete.-0.60x0.60x0.60 Mtr

Supplying and fixing in position the following UPVC specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and pipes jointing the special complete complying with standard specifications. (The PVC specials used on the work shall be got approved by the departmental officer before use on work). 50mm dia UPVC Elbow With ISI Mark

50mm Dia UPVC TEE with ISI mark

50mm dia UPVC Coupler with ISI mark

Supplying and fixing in position CPVC specials such as plain bend, door bend, plain tee, door tee, off sets of various sizes of best approved quality conforming to ISI and providing leak proof joint including fixing to wall etc., complete complying with standard specification. (The specials should be got approved by the Engineer,i/c., before use on work). 32mm dia CPVC Elbow With ISI Mark

25mm dia CPVC Elbow with ISI mark

20mm dia CPVC Elbow with ISI mark

32mm dia CPVC TEE with IISI mark

25mm dia CPVC TEE with ISI mark

20mm dia CPVC TEE with ISI mark

32mm dia CPVC coupling with ISI mark

25mm dia CPVC coupling with ISI mark

20mm dia CPVC coupling with ISI mark

32mm dia CPVC union with ISI mark

25mm dia CPVC union with ISI mark

20mm dia CPVC union with ISI mark

Supplying and fixing in position PVC specials such as plain bend, door bend, plain tee, door tee, off sets of various sizes of best approved quality conforming to ISI and providing leak proof joint including fixing to wall etc., complete complying with standard specification. (The specials should be got approved by the Engineer,i/c., before use on work). 4" dia PVC Door Bend With ISI Mark

4" dia PVC Plain Bend with ISI mark

4" dia PVC Plain TEE with ISI mark

4" dia PVC Plain Elbow TEE with ISI mark

3" dia PVC Door Bend with ISI mark

3" dia PVC Plain Bend with ISI mark

3" dia PVC Plain Tee with ISI mark

Providing rain water harvesting pit by earth work excavation in circular shape of 90 cm dia at 100 cm depth. The pit is encased with well ring of 90 cm dia , 30 cm depth, 50 mm thick using RCC 1:2:4 using 20 mm metal for 4 nos. The entire depth ie. 120 cm is filled with 40 mm size metal. The top of the pit is covered with RCC 1:2:4 50mm thick perforated slab including cost and fabrication of reinforcement grills for ring and cover slab, labour charges, cost of materials, moulding curing, finishing and fixing in position etc. complete.

Supplying and fixing in position the following Gun metal gate / wheel valve of best quality and approved make and heavy type quality including cost of cutting, threading of the pipes and fixing of the G.I. pipe in position with white lead, spun yarn etc., complete complying with standard specifications. 50mm dia Gate valve

32mm dia Gate valve

Supplying and fixing in position best approved quality C.P. brass soap tray of size 150 x 150 mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position Indian make decorative type wooden framed Mirror of approved quality and brand of size 600 x 450 mm x 5.5 mm shelf type with necessary ply wood backing, rubber buttons, brass CP screws, T.W. plugs etc. complete complying with standard specification. (The mirror should be got approved by the Departmental Officer before use on woks)

Supplying and erecting of 1000 litre capacity PVC Sintex water tank to ISI standard of approved quality and make including labour charges for fixing etc. complete.

Painting new wood work with two coats of synthetic enamel ready mixed paint of approved quality and colour over a priming coat in all floors. The rate is inclusive cost of all materials and labour including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Engineer,,i/c., before use on works).

Varnishing the new wood work two coat with best shellac and with fine best varnish of approved quality varnish over one coat of Bee’s wax of teak wood natural finish including preparation of surface with sand papering including patty priming etc., complete complying with standard specification and as directed by the Engineer,i/c.,

Fabrication, supply, delivery and fixing of outside MS ladder of 45cm wide made out of 50 X 50 X 6mm MS angle for sides and steps in 20mm MS plain rods fixed at 30cm centre to centre welded, jointed etc., providing with suitable side supports, clamps and locking arrangements provided with one coat of red oxide paint for providing access to roof top 30,000 Liters capacity OHT of suitable inclined length, including bottom anchorage and transportation and as directed by the department engineers.

Supplying and fixing in position of C.I. Manhole cover with frame of size 0.60 x 0.60m (Heavy duty) including locking arrangements and as directed by the departmental Engineers.

Providing and fixing of RCC inner access ladder in RCC 1:1½:3 (One cement, one and half M.sand and three aggregates) using 20mm HBG stone for OHT including cost of reinforcement, placing grill in position, centering, shuttering charges, mixing concrete curing etc., to required height and clear width of 45cm consisting of two nos. of vertical post of 10cm X 15cm and step slab of 25mm X 25mm etc., complete and as directed by the department engineers.

Supplying and fixing in position PVC ventilating shaft of 110mm dia with working pressure of 6kg/cm2. PVC cylindrical cowl and covered with mosquito proof mesh and fixing in position as directed etc., complete. (The PVC pipe and cowl should be got approved from the Engineer,i/c., before use on work).

Supplying, laying and jointing 2” dia G.I. pipes of approved quality and best variety of “B” class pipe of the following dia including labour fixing G.I. specials, (excluding charges for cutting and threading of pipes, cost of such specials) to wall with necessary teak wood plugs, clamps, screws, thread balls, shellac etc., making holes on the walls (or) drilling holes in roof and making good the dismantled portions to original condition with necessary brick work / concrete and plastering wherever necessary with necessary scaffolding charges. The pipes are to be painted with the 2 coats of good variety and approved best quality of synthetic enamel paint over a priming coat of red oxide etc., complete in all floors complying with standard specification. G.I. pipes shall be got approved by the Executive Engineer before use on works.

Supplying and fixing in position the following Gun metal gate / wheel valve of best quality and approved make and heavy type quality including cost of cutting, threading of the pipes and fixing of the G.I. pipe in position with white lead, spun yarn etc., complete complying with standard specifications. 2" dia G.M. Gate valve

Floor finishing with Cement Mortar 1:3 (One cement and three P.sand), 10mm thick and finishing neatly including curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying, laying and jointing PVC pipe of the following dia of approved quality and best variety and laid properly to alignment including fixing the required specials lent excluding cost of such specials but including cutting, threading and fixing to the wall with necessary clamps, screws, teak wood plugs making holes in the wall (or) drilling holes in the roof and making good the disturbed portion to the original condition with necessary brick work and plastering etc., complete complying with standard specifications. (The PVC pipe should got approved by the Engineer,i/c., before use on work). 50mm dia PVC pipe - (Schedule - 80) - Below Ground Level

Supplying and fixing in position of weld mesh grill of size as may be directed using 40X40x6mm M.S. angle for outer frame, 40X6mm M.S. flats for bracings, 1¼”X 1¼”M.S. weld mesh 10 gauge for panels including cost of materials, labour for wrought and put up and applying a coat of primer etc., complete.

Providing Granolithic floor finish for 25 mm thickness using plain Cement Concrete 1:2:4 (One cement, two M.sand, and four stone jelly) using 10 to 12mm hard broken stone jelly and the top surface shall be rubbed smooth in all floors, finishing, threading and curing etc., complete complying with standard specification.

Plastering in cement mortar 1:3 (One cement and three P.sand) 12mm thick in all floors with water proofing compound at 2% by weight of cement and finishing neatly including provision of cement mortar bands and raised plastering for doorways wherever required and as directed without any extra claim complying with standard specifications

Supply laying and jointing PVC pipe of approved quality and make of the following dia fixed on walls with necessary clamps and screws including cutting and threading wherever necessary, etc. complete complying with standard specification and as directed by Engineer-in-charge. (Below Ground Level). 50mm dia PVC pipe - 10 Kg /CM2 with ISI mark (Finolex or equivalent)

32mm dia PVC pipe - 15 Kg /CM2 with ISI mark (Finolex or equivalent)

25mm dia PVC pipe - 15 Kg /CM2 with ISI mark (Finolex or equivalent)

Supplying and fixing in position the following Gun metal gate / wheel valve of best quality and approved make and heavy type quality including cost of cutting, threading of the pipes and fixing of the G.I. pipe in position with white lead, spun yarn etc., complete complying with standard specifications. 50mm dia Wheel valve

32mm dia Wheel valve

25mm dia Wheel valve

Weathering course concrete using best quality broken brick jelly of size of 20mm uniform gauge in pure slaked lime (No M.Sand to be used) over the RCC roof slab, the proportion of brick jelly to lime being 31:12.5 by volume laid over in a single layer and consolidated to the required designed and finished thickness by beating the concrete with wooden of beaters of approved pattern, keeping the surface constantly wet by sprinkling water, etc. complete as directed by the Engineer-in-charge.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three M.Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position best approved ISI quality PVC Rain water down fall pipes of 110mm dia meter having working pressure of 4Kg/Cm2 including cost of PVC pipe, with necessary shoes, bends, nails, teakwood plugs, screws etc., and fixing of cost iron gratings of required dia meter and special clamps at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cost of brass screws, teakwood plugs to be used shall be 150mm X 25mm in front and 200mm X 75mm in rear and all other sides to a depth of 100mm. The PVC pipe shall be fixed with teak wood plugs by means of “U” clamps using brass screws. Special types of “U” clamp at the centre of the pipeline shall be fixed in addition to those for more than 3 meter pipe length complying with standard specifications.

Casting and fixing of RCC Precast slab of 50mm thick in Concrete Cement 1:2:4 (One Cement, two sand and four stone jelly) using 20mm broken granite stone jelly excluding cost of reinforcement grill in position but including moulding charges, casting of jally, finishing, curing, fixing the jally in position and pointing the joint with C.M 1:2 in full depth in all floor etc., complete complying with standard specification.

Supplying and fixing of M.S. pipe of various sizes (3" dia pipe for vertical posts and 1½" dia M.S. pipe for stay) embedding with cement concrete 1:2:4 to a depth of 0.50 and leaving 1.50m above the ground including providing necessary for lening applying a coat of primer ect. complete.

Supplying and fixing of powder coated galvanized aluminium metal roofing sheet 0.47mm thick jew or equivalent of ISI make of different colour sheet for roofing with necessary adjustable ridges seater by using “U” or “J” bolts and nuts with washers or SDST screws and also the labour charges for fixing in position etc., complete as directed by the Engineer,i/c.,

Supplying fabricating, erecting of colour Galvalume 0.47mm ridge sheet including cost of self drilling (SDST) screws with washers, fixing charges lead and lift etc., complete.

Bidder Name

SRI NAACHIMAAR ENGINEERING CONSTRUCTIONS