PROVISION OF PARKING SHEDS QRT ROOM ALONGWITH REST ROOMS AND TOILET BATHROOM BLOCK AT CERTAIN LOCATION AT AF STATION ARJAN SINGH UNDER GE AF PANAGARH

Amount

Sch 'A' Part-I, Earthwork, Site Clearance, Demolition, Dismantling

M&L for Surface dressing n exc 15 cm deep and Site Clearance of any types of soil complete all as specified and directed.

M&L for Surface dressing Soft/loose soil n exc 15 cm deep complete all as specified and directed.

Excavating in trenches in any type of soil not exc 1.5m wide and n.exc 1.5m in depth for foundation etc and getting out complete all as specified and as directed

M&L for hard core (broken stone) of gauge n.exc. 63mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rolled / rammed to a true surface complete all as specified and directed.

Earth (approved) filling under floors, spreading, levelling in layers n.exc 25cm thick each incld watering & well ramming as specified.

Excavating in post holes in soft/loose soil n.exc. 0.5 cum and getting out and removing surplus soil to a distance n.exc. 50 mtr and making good the surface complete all as specified and directed.

M & L for sand filling under floors or in foundations including watering and connsolidation as specified and directed

M&L Damp proof course 40 mm th in cement concrete 1:2:4 type B-0( using 12.5 mm graded stone aggregate) to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M & L for Damp proof course, Bitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.5kg. per sq. m per coat and Polythene film, black, 50micron laid in floors complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft and loose soil.

Excavating over areas, n exc 1.5 m deep and getting outand getting out in soft/loose soil complete all as specified and as directed.

Excavating over areas, exc 1.5 m deep but not exc. 3.0 m deep and getting out getting out soft and loose soil

Sch 'A' Part-II, B/R Work

Material and labour for cement concrete 1:4:8 type D -2 using 40mm graded crushed stone aggregate as in fdn filling and mass concrete complete all as specified and as directed by Engineer-in-Charge.

M&L for reinforced cement concrete design mix M-25 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and the like complete all as specified and directed.

M&L for reinforced cement concrete design mix M-25 (using 20mm graded stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L RCC design mix M-25 (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M & L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, build in cement mortar (1:6) complete all as specified and as directed.

M&L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for cloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

TMT mild steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally or hooping for cloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&l for Mild steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter of rough finished surfaces of concrete flat complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions etc. of rough finished surfaces of concrete flat complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. of rough finished surfaces of concrete flat complete all as specified and directed.

M & L for Brickwork with fly ash bricks of class 7.5 and above as per IS 12894:2002, straight or curved on plan exc 6m mean radius, build in CM (1:6) complete all as specified and as directed.

M & L for brickwork with fly ash bricks of class 7.5 and above as per IS 12894:2002, straight or curved on plan to any radius in half brick thick walls, built in CM 1:3 complete all as specified and as directed by Engr-in-Charge.

M & L for brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and as directed by Engr-in-Charge.

M&L for 15mm thick rendering on surface other than fair face of brick-workfair faces of brick/concrete/ Stone surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified

M&L 15 mm thick rendering in CM 1:4 on fair faces of brick/concrete/ Stone surfaces,using water proofing compound (WPC measured seperately) finished even and smooth without using extra cement.

Supply only liquid water proofing compound

M&L for two coats of oil bound distemper over a coat of priming coat on newly prepared wall surfaces, all as specified and directed..

M & L for preparation of new plastered surfaces of walls 3mm thick wall care putty on wall and applying two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, over a coat of primer on walls.

M&L for preparation of new surfaces and applying two coats of weather proof exterior emulsion (Anti fungal) paint on wall over a coat primer complete all as specified and as directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L PCC 1:3:6 type C2 (40mm graded stone aggregate) as in foundation, filling & mass concrete complete all as specified and directed.

M&L steel work as in hand rails, wind ties for roof including securing bolts, posts and struts in fencing including cutting top to shape as directed drilling holes, notching for wire etc flat iron fillets for securing wire mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

M & L for structural steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt weldedtubes conforming to I. S.1161- 1979 grade St.-240

M & L mild steel Fe-410W (Gde-E-250) quality B Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without anyattachment

S& F Mild steel bolts(machine made). Neck exc 12 mm but n exc 20 mm purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. exc 30cm long

M&L for preparation of new steel and iron surfaces of any des-cription, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer.

S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified. Make: Tata/Jindal/JSW

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet with approved profile and 0.50 mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed by Engr-in-Charge. Make: Tata/Jindal/JSW

Material and labour for providing 100 mm thick Cement Concrete (1:2:4) type B2 using 40 mm graded stone aggregate as in hard standing finished concrete surface even and smooth without using extra cement all as specified and directed

M&L for 75 mm thick plain cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) in sub base of floor over hardcore over rammed earth.

Material and labour for providing 100 mm thick cement concrete (1:4:8) type D2 using 40 mm graded aggregate as in sub base of floor all as specified and directed.

M&L for 40 mm thick PCC type B-1, (1:2:4) using 20mm graded stone aggregate, complete all as specified and as directed.

Material and labour for glass dividing strips, 3 mm thick and 38 mm wide all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.36 sqm in floors etc set and jointes in neat cenment slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick for CM (1:4) for laying floor finishes.

M & L Coloured Glazed ceramic tiles in vertical surfaces 300x600mmx7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM(1:3) complete all as specified and directed

M&L for Vitrified Ceramic colour tiles light shade (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes complete all as specified and as directed by Engr-in-Charge.

M&L for Vitrified Ceramic colour tiles light shade (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, as in skirting/ dadoo etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick plaster in CM(1:4) complete all as specified and as directed by Engr-in-Charge

M&L for coloured vitrified heavy duty tiles dark shade (premium quality) of size 300mm x 300mm x 10 mm thick (square/ rectangular) polished as in steps/stairs/raiser/vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

M&L for Granite 20 mm thick machine cut, bedded & jointed with grey cement slurry & pointed with white cement with admixure of pigment to match the shade of granite stone in floors, cooking plateform including cutting & polishing over 15mm thick screed in CM(1:4),all as specified and as directed.

M & L for rounding edges of stone slabs one edge, such as steps,cooking platforms and other similar situations, complete all as specified and as directed.

M&L for 6mm thick decorative E-board (approved by GE) fixed in ceiling or laid/Aluminium frame work with Aluminium anodised snap grid frame work as in false ceiling all as specified size of grid 605 X 605 mm with aluminium main T section of size 36.5 X 25 mmX 1.4 mm weighing 0.24 kg per running metre and cross T of size 23.5 X 26.4 X 1.4 mm weighing 0.191 kg per RM with aluminium wall angle of size 40 X 25 X 2 mm including GI supporting wire of 3mm dia incl dismantling existing ceiling and (fibre,pulp,insulation board/slabs/blankets . complete all as specified and as directed.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection laid to slope of 1 in 12 and finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: (a) For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable.Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made. (b) The quoted rate shall be inclusive of required size and dia of M.S. hold fast/ lugs or SS dash fasteners.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

S&F Factory made decorative lamination finish single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58- Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. . Note: (a) For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable.Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made. (b) The quoted rate shall be inclusive of required size and dia of M.S. hold fast/ lugs or SS dash fasteners.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture, proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. Note: (a) Stainless steel butt hinges and necessary S.S screws shall be paid separately

S & F for Soild PVC door frames of size 50mmx47mm madeout of 5mm wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet reinforced with MS Square tube all as specified and as directed.

S & F 30 mm thick Factory Made Solid Core, Single Leaf PVC Moulded Door Shutters 28 to 30 mm thick (stiles), but 2 mm thick 3 D wood grains moulded PVC sheet polyurethene painted on front face and 2 mm prelam PVC sheet on back face with 2,4 or 6 raised panel design, supplying & fixing in frame at site as per specification & drawing

Providing and fixing undermentioned factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. all complete as per approved drawing & direction of Engineer-in-Charge. Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.

Providing and fixing undermentioned factory made uPVC white colour sliding glazed window/ventilators upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. all complete as per approved drawing & direction of Engineer-in-Charge. Two track two panels sliding window/ventilator made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension.

S&F for SS Butt hinges 100 mm long, , and fixed complete all as specified.

Providing and fixing alloy metal brass finished handles of size 150 mm, with necessary screws etc. complete all as specified and directed.

Providing and fixing alloy metal brass finished tower bolts (barrel type) of size 200x10 mm with necessary screws etc. complete all as specified and directed

Providing and fixing alloy metal brass finished sliding door bolt of size 250x16mm with nuts and screws complete all as specified and directed

S&F Aluminium handles, cast type, anodised of size 150mm complete all as specified.

S&F powder coated anodised aluminium ventilator shuters and frame, fixed type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing anodised aluminium snap beading, screws, grills anodised aluminium fittings such as peg styas 150 mm long (3 No. hinges type B-21 100mm long (2 Nos0 suitable handle (1 No.). The ventilator system should be glazed with 4mm thick glass figured glass, pin head type of size as required in ventilatior compete all as specified and directed.

M&L for Returning, filling in soil of any type , inclduing spreading, levelling, watering and well ramming in layers n,exc 25 cm.

Removing excavated material n exc. 50m and depositing where directed at a level n.exc 1.5m above the starting point

M & L for Reinforced cement concrete (nominal mix) type M-20, 1:1.5:3 (20 mm graded aggregate) Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified.

S&F for Rotational moulded polythylene water storage tank (ISI marked multilayer) with float valve, plastic lid cover, double layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs and making connections inlcuding suitable GI wash out, over flow, nipple and including 20mm bore ball valve (minimum weigth of valve 210 gms) high pressure of PTMT with epoxy coated aluminium rod and high density plasic ball screwed for iron pipe and fixed complete all as specifed and directed.

S&F for Rotational moulded polythylene water storage tank (ISI marked multilayer) with float valve, plastic lid cover, double layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 500 ltrs including dismantling old unserviceable tank and making connections inlcuding suitable GI wash out, over flow, nipple and including 20mm bore ball valve (minimum weigth of valve 210 gms) high pressure of PTMT with epoxy coated aluminium rod and high density plasic ball screwed for iron pipe and fixed complete all as specifed and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 15 mm dia on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 20 mm dia on walls/ceiling or laying in floors complete all as secified.

S&F Vitreous China Urinal, Full stall type,white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; including flush pipe, grating and union for discharge pipe, complete all as specified and directed .Make:- Jaquar/Hindware/Cera.

S&F for SS Gratings 100mm dia with/ without waste hole, complete complete all as specified and as directed by Engr-in-Charge.

S&F cast copper alloys Chromium plated fancy type Urinal spreader with Auto closing system Push cock ( Urinal Valve) with chromium plated hose pipe fixed suitable for 15mm dia pipe for urinals all as specified and directed.Make:- Jaquar/Hindware/Cera.

S&F in repairs Vitreous china urinal partition white of size 310x700 mm.Make:- Jaquar/Hindware/Cera.

S & F repair, vitreous china wash down water closet pan (pedestal pattern) white with P or S trap incl flushing pipe , seat and PVC seat cover (white) closed pattern with flat bottom & cover brass chromium plated hinging device, incl connection to drain and to flushing pipe, anti syhonage pipe etc complete.Make:- Jaquar/Hindware/Cera.

S& F Vitreous china squatting pan Orrissa pattern size 580mmx 440mm white with integral foot rest with 'p' or 's'trap including flush pipe PVC 32 mm dia, complete all as specified, making connections to trap and to flush pipe, fixing flushing cistern etc, and making good to floors, fixed in repairs, complete all as specified.Make:- Jaquar/Hindware/Cera.

S&f EWC with wall Hung Cistern,Drainage L Bend Pipe, Gasket and installation kit with PP normal close seat cover, Hinges, fixing Accessories and Accessories set, size:350x480x395 mm 'S' Trap , including to existing water supply line and water closet pan complite.Make : Jaqur cat noCNS-WHT-551SNPP184LZ or equivalent price make of CERA / Hindware

S & F in repairs PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and 32 mm flushing pipe connection to pipe etc. all as specified. Make:- Commander/Hindware/Cera.

S&F table Top basin of size 485x395x150 mm including waste coupling and waste pipe complete all as specified and as directed. Make: Cat No.JDS-WHT-25909 of JAQUAR or equivalent price make of CERA / Hindware .

S&F vitreous china wash basin countr top, white flat back of size(mm)425x425x145(CAT No-ONS-WHT-10901) excluding tap incl bracket,Bottle trap complete all as specified and as directed.Make:JAQUAR CAT NO-ALD-769L250X190 or equivalent price make of CERA / Hindware .

S & F 32 mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete.Make:- Jaquar/Hindware/Cera.

S & F in repairs over head shower rose 150 mm X 150 mm square shape single flow with shower arm square 450 mm long complete all as specified and as directed. Make: JAQUAR or equivalent price make of CERA / Hindware .

S&F single lever wall mixer with telephone shower arrengement, connecting legs & wall flanges , cast copper alloy chromium plated, fancy type, screwed down, of 15mm bore. Make: Jaqur CATNo-FUS-29119 or equivalent price make of CERA / Hindware ,

M&L On site LLDPE for 20 user's septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete all as specified and directed.

S & F CP toilet paper roll holder with flap complete all as specified and as directed. Make: Cat No.AKP - 35753 of JAQUAR or equivalent price make of CERA / Hindware .

S&F Sheet glass sheif assembly consisting of 5.5mm thick glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long .Make:- Jaquar/Hindware/Cera.

S&F Tubular Towel rail Brass cromiumplated 20 mm dia D type 60 cm long between flanges complete.Make:- Jaquar/Hindware/Cera.

S&F Towel ring square with round flange CP Brass all as specified. Make:Jaqur CAT NO.ACN-CHR-1121n/F880007 of Hindware or equivalent price make of CERA .

S&F Towel rack 600 mm Long with Lower Hangers Superior finished CP Brass all as specified.Make:Jaqur CAT NO.ACN-CHR-1181S/F580008 of Hindware or equivalent price make of CERA .

S&F in repairs, Brass CP Wall mixer for mixing hot & cold water with provision of over head shower with 115mm long bend pipe on upper side connecting legs and wall flanges screwed down for iron pipe 15mm dia bore complete all as specified and as directed.(Make : Cat No. CON- 273KNUPR or equivalent price make of CERA / Hindware )

S&F for Angular stop cock with wall flange for 15mm dia of chorumium plated fancy type in repairs complete all as specified and as directed. MAKE: Cat No. KUP-35053PM of JAQUAR or equivalent price make of CERA / Hindware

S&F concealed stop cock with fitting sleeves,operating lever &adjustable wall flange with seal(comatible with ALD-083& ALD -089)valves cast copper alloy chromium plated with long shank and cup (concealed type) fancy type screwed down high pressure screwed both ends for pipe . Make: Jaquar Cat no COP -083KPM /F280027 of Hindware or equivalent price make of CERA ,

S&F for Chroumium plated fancy type 2in1 bib tap fixed with existing pipe all as speicified and as directed : Cat No. KUP- 35041PM of Jaquar or equivalent price make of CERA / Hindware .

S & F in repairs Health Faucet with 8mm dia, 1.5 m long flexible tube and wall hook with back flow preventer in repairs all as specified and as directed MAKE:Cat No.ALD-577 of JAQUAR or equivalent price make of CERA / Hindware .

S&F Corner shelf (with bracket) Make : Jaquar CAT NO-1173 or equivalent price make of CERA / Hindware .

S & F soap dish complete all as specified and as directed. Make:Cat No.ACN-1131N of JAQUAR or equivalent price make of CERA / Hindware .

S&F brass chromium plated telescopic Health Faucet(ABS Body) with 1.2 Meter long Easy Flex Tube in Chrome Finish& wall Hook all as specified Make:Jaqur Cat No:ALD-CHR-573 or equivalent price make of CERA / Hindware

S&F in repairs pillar tap 15 mm bore, chromium plated Continental Right Side Knob Swan Neck complete all as specified. Make :CON-CHR-127BKN of Jaquar or equivalent price make of CERA / Hindware .

S&F in repairs Bib tap fancy type chormium plated fixed to 15mm dia in repairs,complete all as specified and as directed.Make:- Jaquar/Hindware/Cera.

S&F for PVC Connections for 15mm size 450mm length and fixed complete all as specified and as directed. Make:- Jaquar/Hindware/Cera.

S&F PVC connection 60 cm long fitted with PTMT nut and washer on both ends, fixed to 15 mm bore iron pipes.Make:- Jaquar/Hindware/Cera.

S&F vitreous china wash basin countr top, white flat back of size(mm)425x425x145(CAT No-ONS-WHT-10901) excluding tap incl bracket,Bottle trap complete all as specified and as directed.Make:JAQUAR CAT NO-ALD-769L250X190 or equivalent price make of CERA / Hindware .

S&F for 600 mm long PVC hot water connection pipe including nuts for Geyser hose pipe complete as in repairs all as specified and directed.(Make: Blue Star & Silver Shine/ Prayag Polymer Pvt. Ltd./ Polytuff)

S&F PVC (SWR) Floor/Nahani trap, plain with CP grating including jointing to waste pipe with solvent cement, dia of outlet 75mm, complete all as specified.

S & F for PVC (SWR) pipes 75 mm single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed.

S & F for PVC (SWR) pipes 75 mm single socketed, in any length with rubber ring joints, fixed to walls,complete all as specified and as directed.

S & F for PVC (SWR) bends 75mm any radius, complete all as specified and as directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S & F for PVC (SWR) pipes 110mm single socketed, in any length with rubber ring joints, laid in trenches or in floors,complete all as specified and as directed.

S & F for PVC (SWR) pipes 110mm single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and as directed.

S & F for PVC (SWR) vent cowl 110mm complete all as specified and as directed.

M & L for RCC design mix M-25 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc of rough finished surfaces of concrete flat complete

On site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type o soil, PCC 1:4:8 below foundation, vent shaft, connection etc complete or

M&L for Cement concrete type 1:2:4 type B2 (40mm stone aggregate) in foundations, filling and mass-concrete complete all as specified and directed.

Material and labour salt glazed stone ware drain pipes 150 mm bore grade ‘A’ laid in trenches and jointed in cement mortar 1:1 complete all as directed and specified.

M&L for Concrete bed to drain pipes of size 150mm bore including forming cradles in cement concrete 1:3:6 type C2, complete all as specified and directed.

Reinforcement concrete pipes, class NP3 of size 150mm, laid and jointed complete with collars complete all as specified and directed.

Supply only liquid water proofing compound

M&L for Providing cement concrete 1:2:4 type B1 (20 mm stone aggregate) as in coping, benching complete all as specified and directed.

M&L for cement concrete type B-0,1:2:4 (12.5mm graded stone aggregate) as in coping incl surface channel of drain and manhole necessary formwork complete

M&L Cement concrete type C2-1:3:6(20 MM graded stone aggregate)in surface channels and drains

Material and labour for reinforced precast cement concrete 1:2:4 type B1 using 20 mm graded crushed stone aggregates in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces with cement mortar 1:4

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in sub base of floor over hardcore over rammed earth.

M&L for non skid heavy duty vitrified outdoor (designer) tiles of size 300mmX300mmX10mm to 12mm thick as in floors etc jointed in neat cement slurry and pointed in white cement with pigment to match with the colour of tiles over 15mm thick screed in CM (1:4) complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in coping including weathering, slightly rounded or chamfered angles and throating, as directed and necessary form work complete all as specified and directed.

M&L for Black bituminous paint on steel surfaces complete all as specified and as directed by the Engr-in-Charge

Sch 'A' Part-III, E/M Work

M&L for Point wiring (concealed) controlled by one switch with 1.50 Sqmm (nominal area) FRLSH, PVC insulated 1100 volts grade multi stranded copper conductor single core unsheathed cable and FRLS, ISI marked, PVC insulated 1100 volts grade multi stranded copper conductor single core of size 1.50 Sqmm as earth continuity conductor connected to common earth dolly, not less than 1.50mm thick, drawn through in and including rigid PVC conduit (Medium Grade) of suitable size, with all fittings, ISI marked and accessories, the pipe shall be fixed with clamping and shadle including provision of mild steel terminal boxes/Sunken boxes of suitable size made with 1.22 mm thick mild steel sheet recessed in wall with a coat of black bituminus paint , suitable for fixing of switches / sockets / etc. fixed in recess of wall with brass chromium plated screws and cap washer complete all as specified and directed for the following :-

(a) One light point controlled by one way switch 5/6 amps.

(b) One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps.

(c) One socket out let 5/6 amps point on the independent board

(d) One socket out let 5/6 amps point on the same board

All as per item No above but wiring with 2.5 sq mm single core multistranded copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and directed

S&F of Modular switch, single pole, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular switch, single pole, one way, 16 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 5 Pin, 6 Amp, 2 Module, 230 volts, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 6 Pin, 6/16 Amp, 2 Module, 230 volts, (ISI marked) complete all as specified and as directed.

S&F of stepped type modular electronic fan regulator 120 watt 2 module suitable for 1200/1400 mm sweep energy saving fans,ISI marked complete all as specified and directed.

S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and directed.

S&F LED white glass Lamp 1x9 Watt 230V Base-22 complete all as specified and directed.

S&F in ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed.

S&F IP 20, class I, LED light 1X18 W (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified.

S&F IP 20, Class I, LED Mirror light fitting 1 x 10 W, (or nearest next higher wattage) 5700 K, wall /Surface mounted with aluminium housing 2 feet long, integrated type, with high efficiency PMMA diffuser, integrated high efficiency electronic driver & surge suppressor of 2 KV or more, luminaire efficacy > 95 lumens/Watt, power factor >/ 0.90, operating range – 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/square blocks, screws etc complete including 01 No 10 W LED lamp with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size including necessary taking down the old unserviceable fitting complete all as specified.

S & F of MCB, DB Vertical TPN, 415 volts 4 ways Double door, IP-43, with MCCB Incomer, metal door, rated bus bars, earth bar, neutral links complete incl. blanking plates as required & fixed flush to wall/other surface complete all as specified and as directed.

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), single door, single pole & neutral with 200 amps rated bus bar, 240Volt IP-43 protection suitable for fixing MCB"S/lsolators complete all as specified and directed. Make : Legrand/ Hager/ABB/C&S.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), single door, single pole & neutral with 200 amps rated bus bar, 240Volt IP-43 protection suitable for fixing MCB"S/lsolators complete all as specified and directed. Make : Legrand/ Hager/ABB/C&S.

Supply and fixing 415V 10KA TPN 32 Amp 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning.

S&F MCB, Triple pole & neutral 63 amps, 240 volts, ‘C’ curve, 10KA complete all as specified and as directed. Make :L & T ,Cat No: BB40630C,& Eqv to Legrand/ Hager/ABB/C&S.

S&F MCB, Single pole & neutral, 32 to 63 amps, 240 volts, ‘C’ curve, 10KA all complete with and including taking down old unsv one as specified and as directed.

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete with and including taking down old unsv one as specified and as directed.

S&F Modular white cover plate with frame 3 module complete all as specified and directed.

M&L for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 Security light fitting luminaire with high power LEDs as light source and driver of capacity 35 watts withpre wired and nacessary mounting arrangements, provision of new 3 core multistranded copper conductor cabe from ceilling rose to fitting and GI Pipe bracket made out of GI pipe medium grade 0.75 Mtr long 32 mm dia , MS clamp, nut, bolt and washers complete all as specified and directed by Engineer-in-charge.

Material and labour for concealed sub-main wiring alongwith earth wire of size of 2 x 6.0 sq. mm + 1 x 6.0 sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete, including taking down old unsv aluminium submain wiring all as specified and as directed. NOTE : Two runs of 6 sqmm conductor for main and one run of 6 sqmm conductor as earth wire with proper colour coding including one run run of PVC conduit shall be measured as one unit length. Connections of cables wit MCBs or bus bar shall be done through appropriate size brass/ copper thimbles

Material and labour for earthing complete with galvanized steel plate electrodes of size600x600x6mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised wire 4.00 mm earth lead by means of nuts, bolts, checknuts and washers including 15 mm bore galvanized iron pipe, medium grade for protection of earth lead upto the length of 7.5 meter towards test terminal and 20 mm bore galvanized iron pipe, medium grade for watering, and providing of charcoal and common salt in alternate layers, includig necessary earth work in any type of soil and including PCC pit in PCC 1:2:4 with provision of wire mesh and funnel, complete all as shown in electrical plate No 5 of SSR Part- I including testing on completion all as directed and as specified.

Supply and fixing ceiling fans complete with blades, down rods of 600mm long and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star including fixing clamp and with all accosaries. Make:- Havells, Model: Swing and equivalent to V-Guard,Usha & Bajaj.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers all as specified and as directed.

Supply and fix electric water heater, storage type steel body with stainless steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

S&F Modular white cover plate with frame 1 module complete all as specified and directed.

S&F Modular white cover plate with frame 2 module complete all as specified and directed.

S&F Modular white cover plate with frame 3 module complete all as specified and directed.

S&F Modular white cover plate with frame 6 module with blank switches as required complete all as specified and directed.

S&F Modular white cover plate with frame 8 module with blank switches as required complete all as specified and directed.

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated PVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 10 sqmm 2 core with and including all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc complete as specified and as directed. (NOTE: Earthwork & Excavation, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule 'A').

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated PVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 16 sqmm 4 core with and including all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc complete as specified and as directed. (NOTE: Earthwork & Excavation, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule 'A').

Supply and laying sub class B bricks of size 25cmx12.5cmx7.5cm (+/-10% tolerance) for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified and as directed.

M&L for 40 mm bore steel tubing light grade ISI marked for protection of cable including necessary joints complete all as specified and as directed. Make: Tata/Jindal/Bansal

M & L for horizontal boring across the existing road without disturbing the road surface for inserting 32mm GI pipe complete all as specified and as directed. Note :- (i) Removal of surplus soil shall be deemed to be include in the unit Rate. (ii) GI pipe will be measured and paid separately under relevant item of Sch 'A'.

bholanath bera (BID ID -3506979)

UNIVERSAL TRADING (BID ID -3507017)

M/S KUMAR AVINASH (BID ID -3495513)

S.M.CONSTRUCTIONS (BID ID -3505434)