Annual Repair of I.T.I at Bhodia Khera (Non-Residential) (Admn. Block, Workshop Block, Scooter Stand and Auto Parking) in Fatehabad Distt. for the year 2021-22 (Re-invited).

Amount

Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 1 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete (HSR 4.33)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkats, architrave, holdfasts etc. complete and stacking within 50 metres lead of area 3 Sq. metres and below (HSR 5.29.1)

Dismantling old plaster or skirting raking out joints and cleaning sqm the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead (HSR 5.45)

Brick work with common burnt clay non-modular bricks of class designation 7.5 in superstructure above plinth level upto floor IV level in all shapes and sizes in: (HSR 7.22.2) Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing & fixing UV stabilised fibreglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified (HSR 9.32.1) 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified

Providing and Fixing on wall face un-plasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382. Leaving 10 mm gap for thermal expansion, (i) Single socketed pipes (HSR 9.57.2) 110 mm diameter

150 mm diameter (HSR 9.57.3)

Providing and Fixing on wall face un-plasticised – PVC moulded fittings / accessories for un-plasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382. Leaving 10 mm gap for thermal expansion, (HSR 9.58.5.3) Bend 87.50 150 mm bend

Bend 87.50 150 mm bend (HSR 9.58.5.3)

Providing and laying conglomerate floor 40 mm thick cement concrete topping 1:2:4 (HSR 10.8)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades, except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 Cement : 3 Coarse Sand) and jointing with grey cement slurry @ 3.30 Kg / Sqm including pointing in white cement mixed with pigments of matching shade complete (HSR 10.58)

Providing and laying ceramic glazed floor tiles of size 300 x 300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make in all colours, shades, except white, lvory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse Sand), jointing with grey cement slurry @ 3.30 Kg / Sqm including pointing the joints with white cement and matching pigments etc. complete (HSR 10.59)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.30 Kg/Sqm including grouting the joints with white cement and matching pigments etc. complete (HSR 10.63.2) Size of tile 600 x 600 mm

Providing and laying 60 mm thick factor made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over (BIS 15658 : 2006) and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-In-Charge (HSR 10.76)

12 mm thick cement plaster of mix (HSR 11.5.4) 1:6 (1 Cement : 6 Fine Sand)

Pointing on tile brick work with cement mortar 1:3 (1 Cement : 3 Fine Sand) (HSR 11.26.1) Flush/ Ruled/ Struck or weathered pointing

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete (HSR 11.58)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade (HSR 11.64.1) New work (two or more coats) over and including water thinnable priming coat with cement primer

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface (HSR 11.67.1) Water thinnable cement primer

Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete (HSR 11.76)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (HSR 11.77)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade (HSR 11.78)

Finishing walls with acrylic smooth exterior paint of required shade (HSR 11.95.1) New work (two or more coat applied @ 1.67 litre/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 Kg/ 10 Sqm

Providing and fixing wire gauge shutters using galvanized MS wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws (HSR 12.19.2.1.2) 30 mm thick shutters with ISI marked MS pressed butt hinges bright, Kiln seasoned and chemically treated Hollock wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross brands and face veneers on both faces of shutters (HSR 12.37.2) 30 mm thick including ISI marked stainless steel butt hinges with necessary screws

Providing & Fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 4.0 mm thick glass panes (HSR 13.10.1)

Supply & fixing Windows frames (Chowkhats) including mullions consisting frame fabricated from sheet roll formed out of 1.2mm thick galvanized sheet as per IS:277 (Base steel as per IS 513) with zinc of 120 gm/sqm & Powder coated with pure Polyester powder up to 50 microns (as per approved colour), 3 Nos. 100mm butt - hinges 2mm thick, 6 Nos. 1.2mm thick CRCA electroplated stiffner, 6 Nos. M.S hold fast with split and tail welded to stiffner plate 200mm long, receiver for aldrop, weld less corner assembly with brackets & screws, M.S tie rod 50mm x 25mm to be fixed at bottom finished with powder coated total thickness of coating 0.6mm of approved shade, fixed in position including the cost of cement concrete for 1:2:4 for fixing lugs complete in all respects as per drawing, design, specification & entire satisfaction of Engineer-in-charge (HSR 13.21.1) Door Frame of size 80mm x 50mm with 37mm wide single rebate for 35mm door shutter

Door Frame of size 125mm x 60mm with 37mm wide double rebate for 35mm door shutter (HSR 13.21.2)

Removing dry or oil bound distemper, water proofing cement paint and the like by scraping, sand papering and perparing the surface smooth including necessary repairs to scratches etc. complete (HSR 30.22)

P.H. Items Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require (HSR 22.1.2) White vitreous chinaware Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required (HSR 22.10.2.2) Kitchen sink without drain board, 610x460 mm bowl depth 200 mm

Providing and fixing draining board with C.I. brackets including painting of brackets, cutting and making good the walls wherever required (HSR 22.11.1) White glazed fire clay draining board of size 600x450x 25 mm

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required (HSR 22.22.1) White vitreous chinaware Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous chinaware pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required (HSR 22.23.1)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge (HSR 22.85.2) 20 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes (HSR 22.85.3)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 (HSR 22.104.1) 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms (HSR 22.105.1) 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 (HSR 22.107.1) 15 mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms (HSR 22.127)

Providing and fixing Unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour (HSR 22.128.1)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the case support for tank (HSR 22.181)

Providing & fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with CP brasss screws and washers complete (HSR 22.209).