Provn of Chain Link Fencing and 200 KVA DG Set

Amount

Excavation in post holes (or similar holes) each not exc. 0.5 Cum, getting out ,returning filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc. 25cm in soft/loose soil and getting out.

S & F mild steel work of any section as in posts and struts in fencing, flat iron as in straps to hold chain link fencing incl. cutting tops to shape as directed , drilling holes, notching for wire etc.,flat iron fillets (for securing wire mesh etc.)incl. all necessary drilling, bolting or riveting etc. and similar workconfirming to FE-290 Gde E-165 complete all as specified.

M&L for cement concrete type C2, 1:3:6 (40mm graded crushed stone agg) as in foundation, filling and mass concrete and similar wks complete all as specified and directed.

M&L PCC type B-1,1:2:4 (20mm graded stone aggregate) as in coping, side kerbs, mud stops etc complete including necessary form work, complete all as specified and directed.

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

M&L for hard core of broken stone or boulders gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface all as specified.

M&L for 100mm thick cement concrete Type B2,1:2:4 (40mm graded agg) as in floors, finished cement concrete surface even and smooth without using extra cement complete all as specified.

M&L for forming contraction (Dummy) joints 65mm deep x 10mm wide filled with sealing compound grade "A" complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails straining bolts, etc including provision of binding wire etc complete all as specified and as directed.

Supply only chain link MS galvanized fencing, any size or type complete all as speciifed and directed.

S&F Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts ,including ,securing or tying at crossing with end provision of galvanised mild steel wire staple or steel pins,etc as directed.

S&F for 10mm round bars as in stiffner to hold the chain link fencing fixed to angle iron post by binding wire or staple pins or by welding as directed, confirming to Fe-410-W(Gde E-250) quality A complete all as specified and directed .

Supply only mild steel screw bolts (machine made) with hexogonal or square heads at one end and screwed the other , or screwed both ends , each screwed end to be fitted with washers and one hexogonal or square nut 11 to 15 mm dia and exc. 5 cm but n exc. 10 cm long complete all as specified and as directed.

Removing excavated material (soil) exc 1.5 Km but n exc 5.0Km and depositing, where directed at a level n. exc 1.5 m above the starting point complete all as specified and as directed.

Supply, strech and fix mild steel concertina coil 750mm dia in stress position hot dip galvanized steel wire coated with CLR anti corrosive paints making diamond shape with the help of dove tail clip (18 SWG) for fencing, fixing with galvanized mild steel wire staple etc complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed.

M&L reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in columns, pillars, piers etc complete all as specified and as directed.

M&L form work to sides of pillars, posts, struts, columns for rough/fair finished surface of concrete complete all as specified.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality confirming to all as specified.

Description same as per item No. 19 above but, 5 mm dia and over and including 10mm dia as in stirrups, spacers and binders

M & L 12mm thick cement plaster on fair faces of brick work or concrete surface on wall in CM 1:6 finished fair and even complete all as specified and directed.

S & F framed work rolled mild steel as in doors or gates of angle or other section with gusset plates, rails, braces etc.,compelete drilled for fixing of steel sheeting or other covering . Doors etc. to be prepared for hanging or sliding with and incl. either hooks and hinges or steel hanging door fittings and hanging, also fastening and fixing confirming to Fe 410-w (Gde E-250) quality A complete all as specified.

M & L for preparation of new (Previously untreated) plastered surfaces of walls and applying two coats of cement based paint on walls, complete all as specified and directed

M & L for preparation of new steel or iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified

M & L for preparation of new steel or iron surfaces of any description not otherwise described not exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5M in depth for foundation etc and getting out in soft/loose soil complete all as specified and as directed.

M & L for brick work using fly ash bricks straight or curved on plan exc. 6 M mean radius built C.M. 1:6 all as specified

M&L for 12 mm thick rendering on fair faces of brick/concrete surfaces in CM 1:6, including finishing the surfaces even and smooth, complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 of type D-2 using 40mm graded stone agrregate as in sub base of floors etc complete all as specified and directed.

M&L for cement concrete type B2, 1:2:4 (40mm graded crushed stone agg) as in foundation, filling and mass concrete and similar wks all as specified and directed.

M&L for PCC 1:3:6 type C-2, (using 40mm graded stone aggregate) as in plinth protection laid in alternate panels 75mm thick finished even and smooth without using extra cement complete all as specified and directed.

S&F for mild steel plate girder or single stanchions, built up of one beam, tube or channel section with flange plates, caps, bases, splices, angle brackets cleats or other connections of Fe 410-W (Gde-E-250) quality 'A' complete all as specified and directed.

S&F for mild steel work in roof trusses (framed) trussed, purlins, crane gantries, rails fastening and heavy framing (Beam, tee, angle, channel or hollow sections ) including distance pieces, cleats etc confirming to Fe 410-W (Gde-E-250 quality-A)

S&F for mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates of Fe 410-W (Gde-E-250) quality 'A' complete all as specified and directed.

S&F for MS Plates (Plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment, Fe-410-W(Gde-E-250) complete all as specified and directed.

S&F Pre-painted Trapezoidal profile galvalume aluminium zinc coating steel sheet (Make: Tata bluescope/ Jindal ) 0.50mm thick (base metal thickness) of any colour having tensile strength of 550 Mpa minimum yield strength conforming to IS - 513 (1994) coated with hot dip alloy of 55% aluminium + 43.50%Zinc +1.50% silicon and finished with resin coat ( of thickness not less than 35 micron) on both surface @150gm/sqm of coating (total both surfaces) of approved colour as in roof covering/cladding, fixed with self tapping screws (make hilty/fissers), neoprene and epdm washers class 3 of AS-3566(5.5-14X5 for crest and 5.5-14X25 for valley fixed) with 150mm end lap and one corrogation side lap whereever required penetrations and lap in sheet shall be sealed by using proper sealant profile/HDPE fillers shall be provided whereever required to close voids between sheets and fastners etc. as in roof covering/ cladding in straight or curved surface in any height complete all as specified and directed. Note : (i) The colour of sheet for bldg shall be approved by GE. (ii) Sheeting shall be fixed of any height.

All as per item No 36 here in before but Trapezoidal section as in ridge,valley,gutters complete all as specified and directed by the Engineer-in-Charge.

M&L for preparation of newly plastered surfaces and applying three coat of white wash on walls complete all as specified and directed.

Supply, installation testing and commissioning of factory assembled 200 KVA silent diesel engine driven generating set specially designed to meet stringent MOEF/CPCB norms of 75 dBA @ 1 Mtr at 75% load under free field conditions.complied with standard control panel, fuel tank of suitable capacity( capacity shall not be less than 10 Hrs consumption), first filled lubricating oil and coolent, designed to have optimum serviceability,air inlet louvers specially designed to operate at rated load, made on special CNC machines for consistency in quality and workmanship, powder coated for long lasting service life and superior finish, with UV resistant powder coating,use of special hardware for longer life insulation material meets exacting IS 8183, specifications for better sound attenuation, flush styling- no projections, Fluid drains for lube oil and fuel, fuel filling point. etc, PCC foundation as per manufactures drawings complete all as specified and comprising of following:-

(A) Prime mover :- Prime mover (Diesel Engine) suitable for driving 200 KVA capacity alternator, 3 Phase 4 wire of 415 V, 50 Hz comprising of water cooled, direct injection, turbo charged, four stroke conforming to IS: 10000/BS- 5514 rated for continous running capable of taking 10% over load for any one hour in 12 hours running complete with Engine control Panel and including following accessories:- Heavy fly wheel and fly wheel housing complete with starting gear ring and to suitable coupling duly covered with guard, Air filter oil bath type/Dry type . Fan and water pump assembly. Fuel pump Electronic Governor, Starter Motor for electric start complete with dynamo/alternator including Maintenance free battery ------01 No (180AH), 24 Volt an initially charged complete with starting/ stopping switch, volt meter and battery leads etc, 01 set Antivibration pad, Make : Cummins, Greaves Cotton, Kirloskar Oil Engines Ltd

(B) Alternator : Synchronous alternator suitable for continuous operation at 1500 RPM, 415 Volts, 0.8pf (lag) suitable for 50 Hz, 3 phase, 4 wire system, conforming to BS 5000/IS 4722. The alternator is brushless type, screen protected, revolving field , self excited, self regulated through an AVR. The alternator has the following features:- (a) + 1.0% Voltage regulation (max) in static conditions. (b) IP: 23 protection with insulation class H. (c) Permissible overload of 10% for one hour in 12 hours of operation. Make : Stamford , Crompton Greaves, catterpillar, KOEL Green

(C) Control & Metering Circuit : The control Panel is manufactured with 14 Gauge CRCA sheet & is powder coated for a weather proof & long lastingfinish. The control panel consists of following parts:- Instrument cluster displaying water and lube oil temperature, lube oil pressure, Engine RPM, running hours, battery charging current with LED indications for battery charging failure and low lube oil pressure, MCCB of suitable rating with overload and short circuit protection. Microprocessor based AMF logic controller, 1 No.kWh meter, 1 No. Line Voltage Monitor as per ISI marked make. 1 Set of Control Fuses, Reverse Polarity indication, 02 No. DC, 12V, 180AH, maintenance free battery each charging ammeter etc complete all as specified and directed by Engr-in-Charge. NOTE :- Silent DG Set will be factory assembled of reputed manufacture ; M/S Sudhir Power , M/s KOEL, M/s Jackson, M/S Greaves Power

(xi) Electronic timer type ET, suitable for 24 Volts, DC supply as per recommendation of DG manufacturer - DC supply for 0-10 second ------------ 01 No. (xii) Electronic timer type, suitable for 240 Volts 50 Hz AC supply for 0-60 second ON relay ----------------------- 02 Nos. (xiii) Electronic timer type, suitable for 240 Volts 50 Hz AC supply for 0-60 second OFF relay -------------------- 01 No. (xiv) Engine starting relay with sequence timer & master timer suitable for 24 Volts DC supply as per recommendation of DG manufacturer ---------------- 01 No. (xv) Battery charging transformer 24 Volts DC as per recommendation of DG manufacturer ----------------------- 01 No. (xvi) By pass arrangment with rotary type by pass change over switch of capacity 315 Amps AC on load to isolate the AMF panel at the time of low voltage. Make : Schinder/Siemens/Legrand. (xvii) Three pole power contactor with standard coil voltage of 415 Volts 50 Hz and axiliary contract of 02 Nos having AC three phase rating of 315 Amps MNX series type of L&T or eqvt of Siemens/Schinder/Legrand/BCH ------------- 02 Nos. (xviii) Booster relay of 24 Volts capacity -------------------------- 01 No. (xix) Provision of protection against single phasing & phaseversal. Make: M/s Sudhir Power, M/s KOEL Green, M/S Greaves Power Note:- DG Set as mentioned in item No 39 of BOQ along with Prime mover, Alternator, Control & Meeting Circuit and AMF Panel with detailed specification, wiring, circuit diagram duly indicating various spares (makes/capacity) along with bill of materials will be got approved from the Accepting officer before placing order to the firm.

(E) Civil Works : As per manufacturer's instruction, (quoted rates are deemed to be included in the item rate). All typle of civil work like foundation, base plate with anti-vibration pad of Make : Dunlop or equivalent ISI marked for engine and alternator and shock vibration absorption material including PCC plateform (1:2:4) type B-1 using 20mm graded aggregate and brick work in CM 1:4 all around the foundation including finished all as directed by Engr-in-charge for resting of DG set and sound proof enclosures.

Supply, laying in trenches passing through pipe/duct fixed to pole testing & commissiong and cable XLPE insulated screened PVC bedded galvanized flat strip or wire armoured electric power cable (Heavy duty) with stranded aluminium conductor LT 1100 volts grade earth system size 400 Sq mm 3.5 core. Make: Havells/Polycab/Plaza/Grandlay

Returning filling including spreading, levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and directed by Engr -in-charge.

M&L for Brick, sub class ‘B’, old size, laid in trenches as in cable protection complete all as specified and as directed.

M&l sand cushioning 8cm below the cable and 15cm above the cable for cable protection in trenches complete all as specified and directed by Engr-in-charge. Note:- After cushioning total thickness measured as 18 cm. (Punned thickness only will be measured & paid)

Supply and laying and fixing in position galvanised iron pipe 80 mm bore light grade fixed to pole with mild steel clamps of required size or laid through wall/under floor/under road/in trenches complete all as specified and directed.

M&L for Earthing complete with Galvanised steel plate 600x600x6.3mm thick, buried directly in ground (earth pit not less than 2.5 m deep below ground level) with top edge of the plate n.less than 1.5 m below normal ground level, connected to galvanised iron strip 32X6mm as earthing lead by means of bolts, nuts, check nuts & washers of tinned brass including concrete chamber shall be in cement PCC (1:2:4) type B-1 Chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1 using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia , PGI funnel and wire mesh, 20 mm dia GI Pipe medium grade for watering complete all as shown in drg and connected to earth test point including testing on completion complete all as specified and directed by Engr-in-Charge

M&L for Boring of holes in true horizontal position under road / pavement / hard standing /Blast Wall by trench less technology using ultra sound technique and necessary machine incl HDPE pipe of 150mm dia suitable for 0.4 mpa working pressure complete all as specified and directed.

Supply and fix ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 630 Amps complete all as specified and directed. Make: Havells Cat Part No; IHCNFE0630 or equivalent to HPL/ L&T.

Supply , install, testing commissioning of factory fabricated CPRI approved outdoor type LT panel board, cubicle type floor mounted suitable for 415 volts, 3 phase, 4 wire, 50 HZ AC supply system having bus bar chamber with air insulated PVC sleeved Aluminium bus bar of rating 800 Amps for phases and neutral installed on porcelain insulators. The panel shall be dust and vermin proof and made out of 3.15 mm CRCA MS sheet and 40X40X6mm thick MS angle iron frame work front and back opening type of adequate and easy maintenance size for housing LT switchgear in separate compartment and, locking arrangement , duly powder coated on both sides including internal wiring in the panel with PVC insulated multi stranded copper conductor cable 1100 Volt grade IS 694 marked or PVC sleeved copper strips of appropriate size and rating and comprising of followings:-

(a) Bus Bar chamber comprising 4 Nos Aluminium strip bus bars air insulated and PVC sheathed capacity 800 Amps with colour coding in separate sheet steel chamber of panel box. INCOMING (b) MCCB 400 Amp rating, 4 Pole , 415 V,adjustable type, Thermal Magnetic based release incoming supply with overload, short circuit and earth fault protection, Breaking Capacity 50KA -1 No Make: Havells /Legrand/HPL. OUTGOING (c) MCCB 400 Amps rating, 4 Pole , 415 V,adjustable type, Thermal Magnetic based release incoming supply with overload, short circuit and earth fault protection, Breaking Capacity 50KA -01 Nos Make: Havells /Legrand/HPL. (d) MCCB 63 Amps, 4 pole, 415 V, 10 KA breaking capacity -1 No Make: Havells Legrand/HPL.

Supply and fix lighting arresters expulsion type complete (with IS-9385 Part-II 1980) all fittings, transmission class discharge capacity of 65 kilo Amp, suitable for HT 11 KV including work steel work reqd for mounting on steel structure complete all as specified and directed by Engr-in-Charge.

Supply and fixing heavy duty Exhaust fan, metal body, AC single phase 230/ 240 volts of size 450 mm sweep, 1400 RPM with louver including appropriate size of wall opening in circular shape complete all as specified and directed by Engr-in-Charge Make: Havells, Model : Turbo Force SP or equivalent to Cromption Greaves/Bajaj.

BAJAJ CONSTRUCTION

M/S ALOK SRIVASTAVA

Ashirwad Contractor and Supplier

B.K.ASSOCIATES

HG construction

Deepesh Electricals