REPAIR MAINT OF EXTERNAL WATER PIPE LINES AND WATER PUMP SETS IN AREA UNDER AGE (I) POKARAN.

Amount

S&F in repair,3 pole contactor (ISI marked) AC type MNX 50. As per IS. complete all as specified & directed by Engineer-in-charge. (Make L & T SWITCHGEAR )

S&F in repair,3 pole contactor (ISI marked) AC type MNX 70. As per IS. (Make L & T SWITCHGEAR ) complete all as specified & directed by Engineer-in-charge. (Make L & T SWITCHGEAR ) .

Taking out the submersible pump set of 12.5 HP to 33 HP capacity from deep bore well with connected cable and column pipes and disconnecting the cable for removing the submersible pump set for carrying out necessary repairs at site incl all loading unloading, veh after repair at work shop complete all as directed by Engineer-in-charge.

M&L for lowering of submersible pump set 12.5 HP to 33 HP in bore well with connected cables & column pipes, re-assembling column pipe with flange ends and testing and commissioning of pump set after repairs including rectification of any leakage to the entire satisfaction of Engineer-in-charge.

M&L in repair for rewinding of AC 3 Phase induction motor of 12.5 HP capacity (Submersible motor) by cutting of burnt winding, cleaning of starter slots, cleaning, bleaching of motor and rewinding with appropriate gauge of copper winding wire complete all as specified & directed by Engineer-in-charge.

M&L in repair for rewinding of AC 3 Phase induction motor of 30/33 HP capacity (Submersible motor) by cutting of burnt winding, cleaning of starter slots, cleaning, bleaching of motor and rewinding with appropriate gauge of copper winding wire complete all as specified & directed by Engineer-in-charge.

M&L for dismantling of 2 to 5 HP capacity motor from 3 phase centrifugal pump set & segregating to its parts for repairs and M & L rewinding of motor with super enameled copper wire of same wire gauge of existing wire including varnishing, turning and polishing to the shaft and / or rotor, including replacement of suitable bearing and spare parts ( if required ) etc incl removing old unsv burnt wire complete & refitting motor after completion of work including testing of motor of following capacity complete all as specified and directed by Engr-in-charge Note : (i) S&F cost ' of bearing and terminal plate will be measured and paid seperately .ii) Rate for transport site to work shop and work shop to site are deemed to be included in the quoted rates.

All as per ser item No 7 here-in-before but capacity of motor 10 to 20 HP

All as per ser item No 7 here-in-before but capacity of motor 30 to 40 HP

All as per ser item No 7 here-in-before but capacity of motor 50 HP

All as per ser item No 7 here-in-before but capacity of motor 75 HP

S & F in repacement of ball bearing suitable for 10-20 HP motor complete all as specified & directed at site.

All as per ser item No 12 here-in-before but suitable for 50 to 75 HP motor complete all as specified & directed at site.

All as per ser item No 12 here-in-before but suitable for 30 to 40 HP motor complete all as specified & directed at site.

All as per ser item No 12 here-in-before but suitable for 2 to 7.5 HP motor complete all as specified & directed at site.

S& F in replacementof coupling suitable for 5 to 7.5 HP Pump set including necessary nuts, bolts, washers, rubber bush etc complete all as specified and directed at site.

All as per ser item No 16 here-in-before but coupling suitable for 10 to 20 HP pump set complete all as specified & directed at site.

All as per ser item No 16 here-in-before but coupling suitable for 30 to 40 HP pump set complete all as specified & directed at site.

All as per ser item No 16 here-in-before but coupling suitable for 50 to 75 HP pump set complete all as specified & directed at site. Note : the rate quoted above are deemed to be included the cost of minor alteration to the shaft of the Pump set for fixing of above coupling complete

S&F in replacement of terminal plate with brass nuts,washers suitable for 3 phase 7.5 HP pump motor complete all as specified and directed at site.

All as per ser item No 20 here-in-before but terminal plate with brass nuts,bolts and washers suitable for 10 to 20 HP pump motor complete all as specified & directed at site.

All as per ser item No 20 here-in-before but terminal plate with brass nuts,bolts and washers suitable for 40 to 50 HP pump motor complete all as specified & directed at site.

All as per ser item No 20 here-in-before but terminal plate with brass nuts,bolts and washers suitable for 75 HP pump motor complete all as specified & directed at site.

S&F in replacement of shaft sleeve suitable for centrifugal pump set of capacity 10 to 20 HP complete all as specified and directed at site.

All as per ser item No 24 here-in-before but shaft sleeve suitable for 40 to 50 HP pump set complete all as specified & directed at site.

All as per ser item No 24 here-in-before but shaft sleeve suitable for 75 HP pump set complete all as specified & directed at site.

S&F in replacement of Impeller set suitable for centrifugal pump set of capacity 10 to 20 HP complete all as specified and directed at site.

All as per ser item No 27 here-in-before but impeller set suitable for 40 to 50 HP pump set complete all as specified & directed at site.

All as per ser item No 27 here-in-before but impeller set suitable for 75 HP pump set complete all as specified & directed at site.

M&L for dismantling centrifugal pump and motor 40 to 75 HP three phase from foundation with base plate, nut, bolt, to shift safe place and cleaning pump motor part with greasing, oiling, gland dori, air release valve, pipe and minor repair and fixing in new foundation with new nut, bolt, elect connection complete with running condition without vibrating the foundation complete all as specified and as directed by Engr-in-charge.

S&F in repair PVC insulated water proof multi stranded copper conductor cable 3 core 10 sq mm 1100 volts grade ISI marked from LT panel to submersible pump motor set in bore well all as specified & directed by Engineer-in-charge.

S&F in repair, star delta starter fully automatic suitable for electric pumpset motors 75 HP cap 3 phase 415volts, comprising of main star delta starter with 'D' range contractor & electric star delta timer in S.S. enclosure complete all as specified & directed by Engineer-in-charge. Make : C&S , L&T / Siemens of equivalent size and specification.

S&F in repair, star delta starter fully automatic suitable for electric pumpset motors 50 HP cap 3 phase 415volts, comprising of main star delta starter with 'D' range contractor & electric star delta timer in S.S. enclosure complete all as specified & directed by Engineer-in-charge. Make : C&S , L&T / Siemens of equivalent size and specification.

S&F in repair, star delta starter fully automatic suitable for electric pumpset motors 40 HP cap 3 phase 415volts, comprising of main star delta starter with 'D' range contractor & electric star delta timer in S.S. enclosure complete all as specified & directed by Engineer-in-charge. Make : C&S , L&T / Siemens of equivalent size and specification.

S&F in repair, star delta starter fully automatic suitable for electric pumpset motors 30/35 HP cap 3 phase 415volts, comprising of main star delta starter with 'D' range contractor & electric star delta timer in S.S. enclosure complete all as specified & directed by Engineer-in-charge. Make : C&S, L&T / Siemens of equivalent size and specification.

S&F, in repair, star delta starter fully automatic suitable for electric pumpset motors 20 HP cap 3 phase 415volts, comprising of main star delta starter with 'D' range contractor & electric star delta timer in S.S. enclosure complete all as specified & directed by Engineer-in-charge. Make : C&S ,L&T / Siemens of equivalent size and specification.

S&F, in repair, star delta starter fully automatic suitable for electric pumpset motors 10/15 HP cap 3 phase 415volts, comprising of main star delta starter with 'D' range contractor & electric star delta timer in S.S. enclosure complete all as specified & directed by Engineer-in-charge. Make : C&S , L&T / Siemens of equivalent size and specification.

S&F in repair, star delta starter fully automatic suitable for electric pumpset motors 5/7.5 HP cap 3 phase 415volts, comprising of main star delta starter with 'D' range contractor & electric star delta timer in S.S. enclosure complete all as specified & directed by Engineer-in-charge. Make : C&S ,L&T / Siemens of equivalent size and specification. Note for item No 32 - 38 : The rate coated above are deemed to be included the cost of minor alteration to the panel for fixing of above starter complete.

Excavation in trenches not exc 1.5m wide and n. exc 1.5M deep for fdn / trenches and getting out for soft / loose soil.

Removing excavated material n exc 50m and depositing at a level n.exc 1.5M above ground.

Returning/filling in layers, spreading leveling, watering and well ramming in layers n.exc 25m in sof/loose soil.

Supply and replacement of MS Pipe 80 mm dia medium grade column pipe (ISI Marked ) in 18 - 20 feet in length, both size of flange welded with 04 no holes in each flange for fixing , with and including nuts and bolts & washers of suitable size of dia complete all as specified & directed by Engineer-in-charge.

taking up/ down of GI pipes 15 mm bore including all fitting from trenches/walls /floors and connections etc complete all as specified and directed at site.

All as per ser item No 43 here-in-before but GI pipe of size 20 mm bore complete all as specified & directed at site.

All as per ser item No 43 here-in-before but GI pipe of size 25 mm bore complete all as specified & directed at site.

All as per ser item No 43 here-in-before but GI pipe of size 40 mm bore complete all as specified & directed at site.

All as per ser item No 43 here-in-before but GI pipe of size 50 mm bore complete all as specified & directed at site.

All as per ser item No 43 here-in-before but GI pipe of size 80 mm bore complete all as specified & directed at site.

All as per ser item No 43 here-in-before but CI/DI pipe of size 100 mm bore complete all as specified & directed at site.

All as per ser item No 43 here-in-before but CI/DI pipe of size 150 mm bore complete all as specified & directed at site.

All as per ser item No 43 here-in-before but DI pipe of size 200 mm bore complete all as specified & directed at site.

Supply, fixing and testing of CI pipe fitting for spigot socketed pipe such as bends (any type, redius and angle), tapers any type (straight, bends, increasing/ decreasing or double socket etc) Tee pieces, single branch, "Y" junctions, double branch, cross ( all sockets spigot ), collar, Caps and plugs, for pipe upto 150 mm bore all as specified & directed by Engineer-in-charge.

M&L for run lead joints including all materials and testing for leakagess including burning out old lead joints and recovering of lead for further disposal for CI pipe line sizes of 80 mm dia complete all as specified and directed at site.

All as per ser item No 53 here-in-before but CI pipe of size 100 mm bore complete all as specified & directed at site.

All as per ser item No 53 here-in-before but CI pipe of size 150 mm bore complete all as specified & directed at site. Note : Quantity of lead of lead retrived from each joint shall be the property of contractor and neccesory cradit shall be recovered as per schedule of cradit for each lead joint and shall be calculated as under (I) for 80 mm dia pipe joint @1.8 Kg per joint (ii) for 100 mm dia pipe joint @ 2.2 Kg per joint (iii) for 150 mm dia pipe joint @ 3.4 Kg per joint

M&L for rubber gasket joint (tyton joint) for CI/DI pipe spigot and socketted pipe fittings conforming to IS 12820-1989/IS 5382-1985 for 150 mm dia CI/DI pipe complete all a specified & directed by Engineer-in-charge.

All as per ser item No 56 here-in-before but CI /DI pipe of size 200 mm bore complete all as specified & directed at site.

M&L for rubber/ fiber board flanged joints including all materials and testing as applicable suitable for 80 mm bore CI pipe including dismantling of old flanged joints complete all as specifiedand directed at site.

All as per ser item No 58 here-in-before but CI /DI pipe of size 100 mm bore complete all as specified & directed at site.

All as per ser item No 58 here-in-before but CI /DI pipe of size 150 mm bore complete all as specified & directed at site.

Supplying, laying & Jointing 15 mm bore galvanised steel water tubings medium grade (ISI marked) laid in trenches with medium grade galvanised iron fitting (ISI marked) such as bends, tees, sockets, nipples & union, flanges etc and connecting complete all as specified and directed at site.

All as per ser item No 61 here-in-before but GI pipe of size 20 mm bore complete all as specified & directed at site.

All as per ser item No 61 here-in-before but GI pipe of size 25 mm bore complete all as specified & directed at site.

All as per ser item No 61 here-in-before but GI pipe of size 40 mm bore complete all as specified & directed at site.

All as per ser item No 61 here-in-before but GI pipe of size 50 mm bore complete all as specified & directed at site.

All as per ser item No 61 here-in-before but GI pipe of size 80 mm bore complete all as specified & directed at site. Note for ser item No 61 to 66 : (i) Excavation and earth work will be measured and paid separately. (2). Suitable size of Union will be provided at all branches tees joints and at a maximum distance of 30 RM of straight pipe and rates are deemed to be included in the rate quoted above for easy in maintenance.

Supply, laying, jointing and testing of cast iron pipes Class 'LA' of size 150 mm bore with spigot and socket ends, centrifugaly cast suitable for tyton joints, in any length, laid in trenches/pillars complete all as specified and directed at site.

All as per ser item No 67 here-in-before but CI pipe of size 100 mm bore complete all as specified & directed at site.

All as per ser item No 67 here-in-before but DI pipe of size 200 mm bore class K-9 (IS-8329-2000) icluding taking down complete all as specified & directed at site. NOTE for ser item No 61 to 69 :- Excavation and earth work, tyton / lead joint, CI specials and fitting will be measured and paid separately

S&F in replacement, Gun metal globe or gate valve, heavy duty SI -778 with iron wheel head, screwed both ends for iron pipe of size 15 mm bore complete all as specified and directed at site.

All as per ser item No 70 here-in-before but Gate valve of size 20 mm bore complete all as specified & directed at site.

All as per ser item No 70 here-in-before but Gate valve of size 25 mm bore complete all as specified & directed at site.

All as per ser item No 70 here-in-before but Gate valve of size 40 mm bore complete all as specified & directed at site.

All as per ser item No 70 here-in-before but Gate valve of size 50 mm bore complete all as specified & directed at site.

S&F non return valve of size 150 dia of GM sheet and flap H7 class both ends flanges including taking down unserviceable non return valve complete all as specified and directed at site.

All as per ser item No 75 here-in-before but NRV of size 100 dia complete all as specified & directed at site.

All as per ser item No 75 here-in-before but NRV of size 80 dia complete all as specified & directed at site.

S&F cast iron air release valve with two air outlet 25 mm dia including gun metal hexagonal nipple with rubber gasket and fixing in CI pipe line including drilling , boring and tapping to CI line for fixing air valve complete including taking out old unserviciable air valve.

S&F in repair, Pressure gauge with chromium plated brass cock and tube range up to 4" dia 0-14 Kg / sq cm for pumpset including all accessories required to be fixed on CI / GI pipe lines including taking out old unserviciable pressure gauge complete all as specified and directed by Engineer-in-charge.

Supply, installation, connecting and testing sluice valve, cast iron body (long body) class PN 1.6 of size 80 mm dia with flanged ends drilled suitable for following bore of pipes, isi marked (IS 14846:2000) having brass spindle with iron wheel at top complete with nuts, bolts,washers, rubber gasket, etc including taking down old sluice valve all as specified and directed at site.

All as per ser item No 80 here-in-before but Sluice valve of size 100 dia complete all as specified & directed at site.

All as per ser item No 80 here-in-before but Sluice valve of size 150 dia complete all as specified & directed at site.

All as per ser item No 80 here-in-before but Sluice valve of size 200 dia complete all as specified & directed at site.

M&L for filling the gland suitable for 150 mm dia nominal bore sluice valve and replacing the old unserviceable nut, bolts washers etc incl removing old gland complete all as specified and directed at site.

All as per ser item No 84 here-in-before but Sluice valve of size 100 dia complete all as specified & directed at site.

S&F in replacement, half turn valve/butter fly valve of 50 mm bore screwed both ends suitable for fixing to G I pipe complete all as specified & directed by Engineer-in-charge.

M & L for cleaning of RCC UG water storage sump / ground level tank by pumping out dirty water & removing all sludge, dirt silt etc from walls and floor of the tank & treating the wall with bleaching powder,rubbing scrasping walls and floor with the wire brushes and taking out all silt, sludge and dirt from the sump and depositing to a distance up to 50 meter complete all as directed by engineer in charge after primery cleaning the empty sump shall be cleaned further with mixture of fresh water and potassium permagnate at the rate two percent with water & washing the sump shall be continued till water stored in the tank shall be continued till water stored in the tank looks clear and then appling two coats of lime wash inside the sump and writing the date of cleaning and capacity of sump of size of letter 4" with synthetic enemel paint (white) distinctively for 20000 - 30000 gallons capacity complete all as specified and as directed by Engr -in-charge.

M & L for cleaning of RCC UG water storage sump / ground level tank by pumping out dirty water & removing all sludge, dirt silt etc from walls and floor of the tank & treating the wall with bleaching powder,rubbing scrasping walls and floor with the wire brushes and taking out all silt, sludge and dirt from the sump and depositing to a distance up to 50 meter complete all as directed by engineer in charge after primery cleaning the empty sump shall be cleaned further with mixture of fresh water and potassium permagnate at the rate two percent with water & washing the sump shall be continued till water stored in the tank shall be continued till water stored in the tank looks clear and then appling two coats of lime wash inside the sump and writing the date of cleaning and capacity of sump of size of letter 4" with synthetic enemel paint (white) distinctively for 100000.00 gallons capacity complete all as specified and as directed by Engr -in-charge.

M & L for cleaning of RCC overhead water storage tank any staging by removing all sludge, dirt silt etc from walls and floor of the tank & treating the wall with bleaching powder,rubbing scraping walls and floor with the wire brushes and taking out all silt, sludge and dirt from the sump and depositing to a distance up to 50 meter complete all as directed by engineer in charge after primery cleaning the empty sump shall be cleaned further with mixture of fresh water and potassium permagnate at the rate two percent with water & washing the sump shall be continued till water stored in the tank shall be continued till water stored in the tank looks clear and then appling two coats of lime wash inside the sump and writing the date of cleaning and capacity of sump of size of letter 4" with synthetic enemel paint (white) distinctively for 50000 gallons capacity including complete all as specified and as directed by Engr -in-charge.

M & L for cleaning of RCC UG water storage sump / ground level tank by pumping out dirty water & removing all sludge, dirt silt etc from walls and floor of the tank & treating the wall with bleaching powder,rubbing scrasping walls and floor with the wire brushes and taking out all silt, sludge and dirt from the sump and depositing to a distance up to 50 meter complete all as directed by engineer in charge after primery cleaning the empty sump shall be cleaned further with mixture of fresh water and potassium permagnate at the rate two percent with water & washing the sump shall be continued till water stored in the tank shall be continued till water stored in the tank looks clear and then appling two coats of lime wash inside the sump and writing the date of cleaning and capacity of sump of size of letter 4" with synthetic enemel paint (white) distinctively for 250000 to 300000 gallons capacity complete all as specified and as directed by Engr -in-charge.

S&F in replacement Tyre Type Automatic Flexible Cushion Couplings – TC Series of TC/P/014 and TC/Q/013 suitable for centrifugal pump sets.

S&F in replacement GREASED AND GRAPHITED Gland packing made from natural fiber, lubricated and graphited used in centrifugal pumps size of 10mm and 12mm.

S&F in replacement, to water level indicator for over head tanks including replacement of brass pully copper float steel wire rope of required size etc. including painting of water level indicator and making good of water level indicator and marking distinctively the scale of water level by synthetic enamel paint all as directed by engineer in charge.

Demolition of concrete in ground floors and pavings n exc 15 cm thickness (belove or above ground level) complete all as specified and as directed by the Engineer-in-Charge.

Demolition of stone/boulder, built in cement mortar including all quoins, arches, pillars, etc, but exceeding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engr-in-charge

M & L PCC 1:4:8 Type D2 (40 mm graded stone aggregate) as in foundations, filling and mass concrete etc complete all as specified and directed.

M&L for Squared rubble masonry , Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified and directed.

M&L for extra over stone masonry for hammer dressing face stones and dressing of the face beds & joints all as specified of squared rubble walling brought upto courses, Jodhpur type, with maximum depression of face from straight edge held against the dressed surface n exc 20mm..

M&L for rendering 15mm thick plaster on stone masonry surfaces in cement mortor (1:6) finished the surface even and smooth without extra cement.

PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in coping etc and like, including weathering, slightly rounded or chamfered angles and throating as directed with and includings necessary fro work complete.

S&F framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 gde E- 165.

M&L preparation of new iron surfaces and applying two coats of synthetic enamel over a coat of red oxide zinc chrome primer complete all as specified & directed.

M&L for Site clearance including clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots, and trees not exceeding 30cm grith and removing rubbish outside the periphery of the area under clearance for soft/ loose soil complete all as specified & directed by Engineer-in-charge.

S&F in replacement MS sheet plate of suitable thickness with nut bolts for CI/DI pipe line 200 mm dia for stop the leakage complete all as specified and directed by Engineer-in-charge.

S&F in replacement MS sheet plate of suitable thickness with nut bolts for CI/DI pipe line 100/150 mm dia for stop the leakage complete all as specified and directed by Engineer-in-charge.

M&L for repair existing leakage of GI pipe line 15 to 25 mm by welding or cutting and making threading for insertion nipple, socket, union socket, pipe piece up to 01 mtr for any place ie. Pokaran/Gomat/Khetolai/Lathi/Nachna complete all as specified and directed by Engineer-in-charge.

M&L for repair existing leakage of GI pipe line 40 to 80 mm by welding or cutting and making threading for insertion nipple, socket, union socket pipe piece up to 01 mtr for any place ie. Pokaran/Gomat/Khetolai/Lathi/Nachna complete all as specified and directed by Engineer-in-charge.

M&L for repair existing leakage of CI pipe line 100 mm by excavation, cutting of pipe for insertion new pipe, if required change the joint, MS round plate clip set for any size of pipe at any place complete all as specified and directed by Engineer-in-charge.

M&L for repair existing leakage of CI pipe line 150 mm by excavation, cutting of pipe for insertion new pipe, if required change the joint, MS round plate clip set for any size of pipe at any place complete all as specified and directed by Engineer-in-charge.

M&L for repair existing leakage of DI pipe line 150 mm by excavation, cutting of pipe for insertion new pipe, if required change the joint, MS round plate clip set for any size of pipe at any place complete all as specified and directed by Engineer-in-charge.

M&L for repair existing leakage of DI pipe line 200 mm by excavation, cutting of pipe for insertion new pipe, if required change the joint, MS round plate clip set for any size of pipe at any place complete all as specified and directed by Engineer-in-charge.

S&F in repais, Brass foot valve ball type heavy duty suitable for 80 mm bore pipe line including dismantling of old unserviciable foot valve any type and make from suction pipe of pumpset at any place complete all as specified and directed by Engineer-in-charge.

S&F in repais, Brass foot valve ball type heavy duty suitable for 100 mm bore pipe line including dismantling of old unserviciable foot valve any type and make from suction pipe of pumpset at any place complete all as specified and directed by Engineer-in-charge. Note for item No. 104 to 113 : (a) The rate quoted for above item are deemed to be included the cost of minor repair/alteration to the pipe or fixing of above foot valve complete. (b) The all complaint should be done within two days of any place/location other wise Rs. 500/- panality recovered from the contractor.

S& F in replacement detachable joints with rubber ring suitable for CI pipe line 150 mm bore including dismantling taking out unserviciable joint at any place complete all as specified and directed by Engineer-in-charge.

M&L for detachable joints with rubber ring suitable for CI pipe line 200 mm bore including dismantling taking out unserviciable joint at any place complete all as specified and directed by Engineer-in-charge.

M&L for detachable joints with rubber ring suitable for CI pipe line 100 mm bore including dismantling taking out unserviciable joint, at any place complete all as specified and directed by Engineer-in-charge.

M&L for detachable joints with rubber ring suitable for GI/CI pipe line 80 mm bore including dismantling taking out unserviciable joint at any place complete all as specified and directed by Engineer-in-charge

M&L for spray painting of Pump & Electric motor at site with one coat of weather proof grey synthetic enamel paint after removing all dust rust carbon and oily spots, including well preparation of surfaces and writing / marking SM / MES No as 25 mm stencil with white paint complete all as specified including painting of suction & delivery pipe lines inside the pump house and arrow marking of water direction all as specified and directed for pump set rating of 20 HP to 75 HP at any place complete all as specified and directed by Engineer-in-charge.

Taking down one old u/s existing feeder piller box and Supply, installation, testing and commissioning CPRI approved Make LT panel wall mounted cubicle canopy type, outdoor dust and vermin proof made out of CRCA sheet 3.15 mm thick steet sheel and 40x40x6 mm angle iron section with hinged cubical doors front side openable having locking arrangements and all accessories complete as per IE rule with powder coated paint over one coat of red oxide primer complete with required fixing arrangements etc and all accessories incl necessary PCC (1 : 3 : 6) type C2 as in foundation all as directed, comprising of the following :

(i) 200 Amp MCCB 4 Pole, 36KA - 01 No. Make - Havells,(Incomer) (ii) Aluminium Bus Bar 400 Amps 4 way (iii) 100 Amp MCCB 4 Pole, 25KA - 2 No. Make - Havells (Out going) (iv) 63 Amp MCCB 4 Pole, 25KA - 1 No. Make - Havells (Out going) (v) MCB TPN 63 Amps 25 KA Make - Legrand (Out going) (vi) Digital type Ameter , range 0 to 400 Amp with slector switch and CT Make : AE (vii) Digital type Volt meter, range 0 to 500 Volt with slector switch and PT. Make : AE (viii) Indicator lamp RYB LED. (ix) 3.15 mm thick CRCA Sheet and angle iron 40 X 40 X 6 mm frame

Shree Karni Construction