Construction of Deep Burial Pits and safe pits for sharp wastes for Project Hospital, Kom-Keirap, Loktak Power Station.

Amount

Earth work excavation by mechanical means (Hydraulic Excavator) /manual means in foundation trenches or drain (not exceeding 1.5 m in with or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surpluse excavated soil as direction, within a lead of 50 m. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm normal size)

Brick work with 1st class common burnt clay F.P.S. (non-modular) bricks in foundation and plinth in: 1:4 (1 cement : 4 coarse sand)

12mm cement plaster of mix : 1:4 (1 cement : 4 fine sand)

Neat cement punning.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.5.20.2 TMT Bar.

Centering and shuttering including strutting, propping etc. and removal of form for: 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete.

Providing and laying in position specified grade of reinforced cement concrete Excluding the cost of centering, shuttering, finishing and reinforcement – All work upto plinth level :5.1.11:1.5:3(1 cement: 1.5 coarse sand : 3 graded stone aggregate 20mm

Steel work in built up tubular (round, square or rectangular tubes etc.) trusses etc., including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc. complete. 10.16.3 Electric resistance or induction butt welded tubes.

Providing and fixing precoated galvanised iron Profile sheets (size, shape and pitch of corrugation as approved by Engineer in-charge) with zinc coating 120 grams per sqm as per IS:277, in 240 mpa steel grade,5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. sheet should have protective guard film of 25 microns minimum to avoid scrateches during transportation and should be supplied in single length upto 12 meter or as desired by Engineer-in charge. the sheet shall be fixed using self drilling /self tapping screws of size (5.5 x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or cured surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with 12.46.2 Precoated galvanised iron profile sheets 0.40mm thick.

Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required. In grating, frames, guard bar, railing, brackets, gates and similar works.

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of Ist class teak wood and priming coat with approved steel primer all complete.

Providing and laying factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of course sand filling the joints with fine sand etc. all complete as per the direction of Engineer in charge. 6.1 60mm thick.

Add EPF @ 3.25%

Add CESS @ 1.00%

Add GST @ 18.00%

M/S RAJ ENTERPRISES (BID ID -3163332)

M/S ANGOM DEBACHANDRA SINGH (BID ID -3164747)