Development of Bus Depot fo...

Amount

Constructing Silt trap at maximum silt accumulation location of strom water drain on design and build basis and as approved by Engineer-in-Charge of size 1500mm x 3000mm x 2000mm deep in R.C.C. walls including necessary excavation, PCC 100mm thick (1:2:4)(1 cement : 2 coarse sand derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) and Raft 450mm thick, RCC walls 230mm thick and RCC slab 300mm thick and RCC baffle wall 600mm high in M-30 grade including reinforcement, centering and shuttering , MS Screen etc. and Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality as per drawing or as directed by Engineer-in-Charge.

Constructing Brick masonry Rain Water Harvesting pit 3m dia and 5m deep with bricks of class designation 10.5 in cement mortar 1:6, base concrete 1:4:8 below the brick wall, including cost of necessary excavation in any type of soil, back filling as required in 20cm thick layers, dewatering if any, shuttering and shoring and disposal of surplus excavated material. 1 no. 300mm dia borings to a depth of 150 metre (to be measured from the bottom of the Harvesting pit), provisioning and fixing 160mm O.D. PVC pipes, tested to 6kg/sqcm, in each bore and upto the height of 300mm above the RCC top slab. The PVC pipe shall be slotted except 3.0 metres at the top and 3.0 metres below from the bottom of the pit, which shall be blind. Top of the PVC pipe shall be covered with PVC Socket and plug. Each bore around the PVC pipe shall be filled with pea gravels. The harvesting pit shall be filled with river stone/pebbles as shown in drawing. The top slab shall be 150mm thick with RCC M20 including nominal reinforcement and 2 nos. of 560mm internal dia SFRC manhole covers with frames conforming to IS:12592 (total weight of cover and frame shall not be less than 182 kg) shall be provided in the top slab. PVC encased 12mm dia steel bar Footrests shall be provided 300 centre to centre. 300mm dia RCC pipe for inlet and overflow.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron `Y` shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and erecting 2.00 metre high temporary barricading at site as per drawing/ direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in- Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge.(Note :- One time payment shall be made for providing barricading from start of work till completion of work i/c shifting. The barricading provided shall remain to be the property of the contractor on completion of the work.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge)

Providing and fixing K-Span open roofing on design and build basis to protect Charging Infrastructures [K-Span Sheet Thickness = 1.00 mm (Min.)], the sheeting material should conform ASTM A-792 Standards, PPGL coil: Width 914 mm, Thickness and Tensile Strength as per the approved Design and Technical specification, Galvanized Coating: AZ-150, Paint Coat: Regular Modified Polyester, Paint Coating: 20-25 microns above 5-7 microns primer, 5-7 microns above 5 microns primer (Back coat Industry color), including, fabrication, consumables, profilling the sheeting material at site with the help of K-Span machines, erection in position including any purlins etc. if required, one hanger/ tab per 4 Sq Mtr roof area having maximum point load capacity of 40 kg complete inclusive all, as per technical specification and as per the direction of Engineer-in-Charge. The Contractor shall submit the shop drawing of all the K-Span roofing for approval of the Engineer-in-Charge, including sample of the material for choosing colour etc.before any procurement. The payment shall be made based on the actual finished roof curved area at site. The contractor has to ensure two years warranty term against any leakage or manufacturing defect for which 5% amount shall be kept hold till end of two year from the date of commissioning or can be release against an equivalent amount of bank guarantee

Providing and fixing K-Span open roofing on design and build basis to protect Workshop Block [K-Span Sheet Thickness = 1.30 mm (Min.)], the sheeting material should conform ASTM A-792 Standards, PPGL coil: Width 914 mm, Thickness and Tensile Strength as per the approved Design and Technical specification, Galvanized Coating: AZ-150, Paint Coat: Regular Modified Polyester, Paint Coating: 20-25 microns above 5-7 microns primer , 5-7 microns above 5 microns primer (Back coat Industry color), including, fabrication, consumables, profilling the sheeting material at site with the help of K-Span machines, erection in position including any purlins etc. if required, one hanger/ tab per 4 Sq Mtr roof area having maximum point load capacity of 40 kg complete inclusive all, as per technical specification and as per the direction of Engineer-in-Charge. The Contractor shall submit the shop drawing of all the K-Span roofing for approval of the Engineer-in-Charge, including sample of the material for choosing colour etc.before any procurement. The payment shall be made based on the actual finished roof curved area at site. The contractor has to ensure two years warranty term against any leakage or manufacturing defect for which 5% amount shall be kept hold till end of two year from the date of commissioning or can be release against an equivalent amount of bank guarantee.

Designing of MS Structure for K-Span roofing on design and build basis to protect Charging Infrastructure and Workshop facilities, as per technical specification and as per the direction of Engineer-in-Charge. The Contractor shall submit the shop drawing of all the MS Structure for K-Span roofing for approval of the Engineer-in-Charge

Supply, installing, testing and commissioning of Effluent Treatment Plant [ETP] of approved make on already constructed tanks of 12000 ltrs treated capacity as per the attached drawings to treat the effluent (waste wash water) biophysically (without use of any chemical) including providing and fixing pumps of standard design to recycle the treated water for reuse (electrical and plumbing) complete in all respects (labour, machinery, etc.) as per the requirement and direction of Engineer-in Charge

Steel Almirah (DSS 5505) without locker and heavy quality.Dimension: 78`x36`x19`

Cash chest fire resistance: 36`x24`x24`

Staff lockers with 18 lockers : 78`x36`x19` (Deluxe Storage-DLSX 1010)

Plastic chairs make neel kamal or equivalent

Steel Racks open type (DSS 5532) with 5 shelves 10g/18g : 72`x36`X15`

Office table with 3 drawer boxes in sun mica with make Godrej lock or equivalent: Dimension:36`x24`x30`

Chair PCH 7044R - Fabric with base in metal

Front Desk with pedestal table (Executive Office Desk - DAS 8002) Size: 1500x750x750 mm in prelaminated particle board

Supply, Installation testing Commissioning of Water cooler with inbuilt Aqua guard RO Purification of Storage type 80 ltrs capacity (Blue star or Voltas make) made of Stainless-steel tank of SS304 grade all complete i/c plumbing and drainage arrangement and electrical connection etc.

Supply of XLPE (E)II kv HT XLPE Insulated aluminium conductor armoured cable.3c x 300 Sq.mm

Main PCC Panel : IP54 Compartment : Incomer:- 1No. 800A, 4pole, 50kA EDO ACB with Microprocessor Based Released O/C, S/C and E/F Protection–Schneider/ABB/Siemens Make:Bus bar:- 400A, Air Insulated, AL.: Outgoings:- 5 No. 100A,FP 25kA, MCCB with Microprocessor Based Released O/C and S/C- Schneider/ABB/Siemens 6 No. 63A, 4P, 25kA, MCCB with Microprocessor Based Released O/C and S/C - Schneider/ABB/Siemens

Supply of 150W LED high bay luminaire having powder coated high pressure die-cast aluminum housing and LED driver compartment, secondary lens optics provided, IP66 complete with driver etc. , pre-wired fixture complete in all respect as directed by engineer-in-charge. High Mast

Supply of 18W LED Tube light fitting (1200mm length) surface mounted, having powder coated aluminum housing with driver complete with all accessories complete in all respect as directed by engineer-in-charge.

Supply of following 60-watt LED floodlight luminaire with high pressure die cast housing with IP66 degree of protection. 60 watts complete in all respect as directed by Engineer-in-charge.

Supply of Industrial type heavy duty wall fan 600mm sweep , double ball bearing, complete with all accessories complete in all respect in all respect as directed by engineer-in-charge.

Supplying stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. ( single module).complete in all respect in all respect as directed by engineer-in-charge.

Supply of 2` x 2` LED Ceiling Panel 36 watt recessed type, 6500 K luminare Metal body frame complete in all respect in all respect as directed by engineer-in-charge.

Supply Installing and analysing 90 watt LED light fixture having Die-cast housing with Epoxy coating and having profiled cooling fins at the top for effective heat dessipation separate driver and LED lamp cavity, heat resistant toughened clear glass cover with high transmittance and high quality gasketing system, high power LED complete as required on existing 8 mtr poles including transportation and connection complete in all respect as directed by engineer-in-charge.

Supply of following sizes of 1.1KV grade multicore aluminum/copper conductor XLPE insulated and PVC sheathed armoured cable conforming to IS : 7098 (Part-I) 1998. 4C X 6 Sqmm Aluminium cable

Supply of following sizes of 1.1KV grade multicore aluminium/copper conductor XLPE insulated and PVC sheathed armoured cable conforming to IS : 7098 (Part-I) 1998. 4C X 10 Sqmm. Aluminium

Supply of following sizes of 1.1KV grade multicore aluminium/copper conductor XLPE insulated and PVC sheathed armoured cable conforming to IS : 7098 (Part-I) 1998. 4C X 16 Sqmm. Aluminium

Supply of following sizes of 1.1KV grade multicore aluminium/copper conductor XLPE insulated and PVC sheathed armoured cable conforming to IS : 7098 (Part-I) 1998. 4C X 35 Sqmm. Aluminum

Supply of following sizes of 1.1KV grade multicore aluminium/copper conductor XLPE insulated and PVC sheathed armoured cable conforming to IS : 7098 (Part-I) 1998. 3½C X 50 Sqmm. Aluminium

Supply of following sizes of 1.1KV grade multicore aluminium/copper conductor XLPE insulated and PVC sheathed armoured cable conforming to IS : 7098 (Part-I) 1998. 3½C X 70 Sqmm. Aluminium

Supply installation testing and commissioning of pure sine wave Inverter of Capacity:-2000 VA/ 24 V and input voltage:- more than 1500 Watts, batteries of capacity 150 Ah/12 V with trolly and suitable output frequency 50 Hz, Battery Low Cut off 21 V, No load output voltage 220 V and necessary connections in all respect as directed by engineer-in-charge.

Supply of Inverter Split AC with outdoor unit, anti-dust filter, 2 Tons Capacity, 5 Star rating,

Installation testing and commissioning of Split AC with outdoor unit, anti-dust filter, 2 Tons Capacity, 5 Star rating, and all necessary connections complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of IP based Full HD 1080p Bullet Camera, IR LED irradiation distance Approx. 30 m, 30 fps image, 2 megapixel, FR 0.3 m, Day/Night capability, H.264 and MJPEG codec, triple stream support, PoE Supported, Motion detection, with FCL 10mm lens, including junction box and powder coated complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of IP based Full HD Indoor Dome Camera, 3 mega pixel [4 : 3] (30 fps) image with sensor, super resolution techniques, ensures glare-free images, True Day/Night provides vivid colour images by day and clear black-and-white images at night with ICR, Excellent low-light performance with 3D noise reduction, saving storage and bandwidth together with VFL 13/32 inches, motorized focus/zoom lens, IR LEDs provide up to 30 m , Smart IR technology provides even distribution of IR, Complete as required, Support Defog, Motion Detection, Audio and alarm supported, SD Card Supported , PoE supported, IP 66 rated, including junction box and powder coated complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of 32 Channel Network Video Recorder having internal memory 10 TB and Expendable to 48 TB with video management software with 4 SATA ports, H.265/ H.264 compression, non-VMS surveillance, 512 mbps with HDMI interface, 1 RJ 45 - 10/100/1000 M port for communication, Alarm Input and 1 Output client Support H.264 Video Compression, including junction box Complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of Hard Disk Drive(6TB) etc. complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of 55` LED TV with 1920x1080 full HD resolution and as per specifications attached suitable for mounting on wall including connection etc. complete as required.

Desktop set:Intel(R) Core(TM) i3-9100 CPU @ 3.60GHz 3.60 GHz, 8.00 GB RAM, 1 TB Hard disk, 21.5 inch screen, 64-bit operating system, x64-based processor, Windows 11 Pro complete in all respect as directed by engineer-in-charge.

8 -10/100/1000Mbps RJ45 ports, Durable metal casing with Power Cord, Installation Guide, Rubber Feet complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of 24U Rack, With all Accessories For Network Video Recorder. In Control Room etc. complete in all respect as directed by engineer-in-charge.

Supply, laying, testing and commissioning of single mode 6 CORE OFC unarmoured cable direct in ground with 32 mm HDPE pipe including excavation and back filling etc.complete in all respect as directed by engineer-in-charge..

Supply, laying, testing and commissioning of SFP Modules complete in all respect as directed by engineer-in-charge.

Supply, laying, testing and commissioning of12 Port Fully Loaded LIU Box with Pig tails complete in all respect as directed by engineer-in-charge..

Supply, laying, testing and commissioning of HDMI Cable(5Mtr),complete in all respect as directed by engineer-in-charge.

Supply, laying, testing and commissioning of Inds.Juncation IP66 Enclsoure for field location 380x280x180,/ IP66, including power point and Mountings complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of 2 KVA online UPS with 1 Hour Power Backup including suitable battery and battery rack, complete in all respect as directed by engineer-in-charge.

Supplying and fixing of following sizes of steel conduit along with accessories in surface / recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit ,complete in all respect as directed by engineer-in-charge. 20 mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface / recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit complete in all respect as directed by engineer-in-charge. 25 mm

Supply, installation, testing and commissioning of Sound Projector speakers speech and music reproduction in indoor /outdoor type for clear reproduction of speech, waterproof, inputs 10 Watt ,along with Junction Box, etc, complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of Voice Alarm Router is and expansion unit that can add up to six zone, Connectors MC1,5 / 14-ST-3,5 having feature of multiple zone amplifiers automatic announcement including with required Professional public address units. automatic volume control system, Bass extended, Voltage230/115 VAC, ±10%, 50/60 Hz, There are to use , taking the complexity away from the user and putting it where it to belongs inside the equipment, providing a crisp call or clear music. etc, complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of 480 W power amplifier in a 3U high 19” housing,EN 54/16 certified,70 V / 100 V and 8 ohm outputs ,Dual inputs with priority switching,100 V input for slave operation on 100 V speaker line, Output power (rms/maximum) 720 W, flat at max volume control )90db, etc, complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of multi zone Call Station/Announcement Unit including a flexible microphone stem, and aunidirectional condenser microphone etc, complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of 6U Wall Mount Rack for PA Syatem complete in all respect as directed by engineer-in-charge.

Supply, laying, testing and commissioning of 2 Core 1.5Sqmm Speaker XLPE Armoured Copper armoured cable 1.1 KV Grade Armoured Power Cable complete in all respect as directed by engineer-in-charge.

Supply and installation of 01 no. 8 passanger elevator/ Automatic Geared a) Capacity:-544 kg b) Speed:- 0.65 mtr/sec, c) Car size:-1.3 x 1.1 mtr d) 415 volts, 3-phase, 50 Hz.A.C e) Indicators:- Combiled luminous Hall Button with digital Hall button indicators at all floors, car operating panel with Luminous button. f) Driving ropes:- 8x19 construction 3 No`s 13 mm g) Acceleration rate 0.6-1m/sec^2 h) Car type i)Door type j) Car size k) Interiors: Ceiling COP Display Mirror- Half height mirror. Handrail Stainless Steel, End-Mounted. sidewall flooring- anti skid-PVC/Tiles flooring and Rubber flooring l) Safety Features:- Over speed governor, Over load sensor, Automatic Rescue Device(ARD), Buffer spring, Car door safety, Landing door safety, Battery operated alarm bell, Firealarm switch at main lobby.complete in all respect as directed by engineer-in-charge.

Providing and fixing M.S Heavy `C` Class Pipe including all fittings like couplings, bends, elbows, offsets, blindflanges, plugs,tees, flanges ( flanges Wall/Tank),etc.welding joints (all type )as required, supports,cutting holes and chases in brick or RCC walls/floors and making good complete as. Pipes conforming to (`C` class).complete in all respect as directed by engineer-in-charge. 25 mm dia

Providing and fixing M.S Heavy `C` Class Pipe including all fittings like couplings, bends, elbows, offsets, blindflanges, plugs,tees, flanges ( flanges Wall/Tank),etc.welding joints (all type )as required, supports,cutting holes and chases in brick or RCC walls/floors and making good complete as. Pipes conforming to (`C` class).complete in all respect as directed by engineer-in-charge. 50 mm dia

Providing and fixing M.S Heavy `C` Class Pipe including all fittings like couplings, bends, elbows, offsets, blindflanges, plugs,tees, flanges ( flanges Wall/Tank),etc.welding joints (all type )as required, supports,cutting holes and chases in brick or RCC walls/floors and making good complete as. Pipes conforming to (`C` class).complete in all respect as directed by engineer-in-charge. 65 mm dia

Providing and fixing M.S Heavy `C` Class Pipe including all fittings like couplings, bends, elbows, offsets, blindflanges, plugs,tees, flanges ( flanges Wall/Tank),etc.welding joints (all type )as required, supports,cutting holes and chases in brick or RCC walls/floors and making good complete as. Pipes conforming to (`C` class).complete in all respect as directed by engineer-in-charge. 80 mm dia

Providing and fixing M.S Heavy `C` Class Pipe including all fittings like couplings, bends, elbows, offsets, blindflanges, plugs,tees, flanges ( flanges Wall/Tank),etc.welding joints (all type )as required, supports,cutting holes and chases in brick or RCC walls/floors and making good complete as. Pipes conforming to (`C` class).complete in all respect as directed by engineer-in-charge. 100 mm dia

Providing and fixing M.S Heavy `C` Class Pipe including all fittings like couplings, bends, elbows, offsets, blindflanges, plugs,tees, flanges ( flanges Wall/Tank),etc.welding joints (all type )as required, supports,cutting holes and chases in brick or RCC walls/floors and making good complete as. Pipes conforming to (`C` class).complete in all respect as directed by engineer-in-charge. 150 mm dia

Supplying and painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved color to givean even shade including surface preparation complete in all respect as directed by engineer-in-charge.. 25 mm dia

Supplying and painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved color to givean even shade including surface preparation complete in all respect as directed by engineer-in-charge.. 50 mm dia

Supplying and painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved color to givean even shade including surface preparation complete in all respect as directed by engineer-in-charge.. 65 mm dia

Supplying and painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved color to givean even shade including surface preparation complete in all respect as directed by engineer-in-charge.. 80 mm dia

Supplying and painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved color to givean even shade including surface preparation complete in all respect as directed by engineer-in-charge.. 100 mm dia

Supplying and painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved color to givean even shade including surface preparation complete in all respect as directed by engineer-in-charge.. 150 mm dia

Providing and fixing one coat of 4 mm thick MAKPOLY KOTE anti rust pipe protection including primer and lap of 25mm on external M.S. pipe complete including surface preparation complete in all respect as directed by engineer-in-charge. 80 mm dia

Providing and fixing one coat of 4 mm thick MAKPOLY KOTE anti rust pipe protection including primer and lap of 25mm on external M.S. pipe complete including surface preparation complete in all respect as directed by engineer-in-charge. 100 mm dia

Providing and fixing one coat of 4 mm thick MAKPOLY KOTE anti rust pipe protection including primer and lap of 25mm on external M.S. pipe complete including surface preparation complete in all respect as directed by engineer-in-charge. 150 mm dia

Excavting treches of required width for pipes, cabales etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5m including getting out the excavated soil and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and deposing of surlpus excavated soil as directed with a lead of 50m all type of soil : Pipes, cables etc. exceeding 80mm dia but not exceeding 300 mm dia. complete in all respect as directed by engineer-in-charge.

Providing and fixing Stainless steel Fire Hydrant valve with 100 mm N B flanged inlet, SS spindal one no. 63 mm dia female instantaneous outlet type SS coupling, blank cap, chain, Conforming to IS:5290 Including tapping from wet riser Complete as required.: Single outlet complete in all respect as directed by engineer-in-charge.

Providing and fixing 63 mm dia 15m long rubberized fabric lined hose including Steel Stainless male and female instantaneous type coupling approved by fire authority, machine wound with copper wire complete in all respects. Hose shall conform to IS 636 TypeII and coupling toIS 903 -1975. RRL Hose pipe complete in all respect as directed by engineer-in-charge.

Providing and fixing standard short size Stainless Steel branch pipe with nozzle 16 mm dia outlet with standard instantaneous type 63 mm dia coupling. Branch pipe complete in all respect as directed by engineer-in-charge.

Providing and fixing first aid fire hose reel wall mounting swinging type fitted with 20 mmdia 30 m long high pressure hose IS. 5132 with 5 mm outlet nozzel with shut off valve conforming to I.S.884-1969. first aid fire hose reel complete in all respect as directed by engineer-in-charge.

Providing and fixing fire hose cabinet fabricated from 16 gaugeM.S. sheet with single or double glazed front door and locking arrangement, painted `Fire Red` with powder coated paint `Fire Hose` written on front including suitable supports to place 900mm above ground level , approximately size 750x600x250 mm deep(to house two lengths of canvas hose with couplings, branch pipeand nozzle for external hydrants). Fire Hose Box complete in all respect as directed by engineer-in-charge.

Providing and fixing dial type pressure gauge with isolation cock and ms pipe at hydrant station.Dial diameter 100 mm celebration 0-10 kg/sq.cm.: dial type pressure gauge complete in all respect as directed by engineer-in-charge.

Providing and fixing C.I. butter fly valves PN1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table E complete in all respects as directed by Engineer-in-charge

Providing and fixing C.I. butter fly valves PN1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table E complete in all respects as directed by Engineer-in-charge 80 mm dia

Providing and fixing C.I. butter fly valves PN1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table E complete in all respects as directed by Engineer-in-charge 100 mm dia

Providing and fixing C.I. butter fly valves PN1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table E complete in all respects as directed by Engineer-in-charge 150 mm dia

Providing and fixing cast iron dual plate wafer type non return valves of PN.1.6 including nuts,bolts, 1.5mmthick compressed asbestos gasket including matching flanges asper table`E` complete in all respects as directed by Engineer-in-charge 150 mm dia

Providing and fixing cast iron dual plate wafer type non return valves of PN.1.6 including nuts,bolts, 1.5mmthick compressed asbestos gasket including matching flanges asper table`E` complete in all respects as directed by Engineer-in-charge 100 mm dia

Providing and fixing brass ball valve full bore type with plastic coated lever and female ends tested to 16 Kg cm2 of approved quality as specified. 25 mm dia complete in all respects as directed by Engineer-in-charge

Providing and fixing SS fire brigade suction 100 mm dia for fire tank complete with campanion flange as per table etc.complete in all respects as directed by Engineer-in-charge Withdrawl

Providing and fixing SS fire brigade suction 100 mm dia for fire tank complete with campanion flange as per table etc.complete in all respects as directed by Engineer-in-charge Four way Inlet connection

Providing and fixing SS fire brigade suction 100 mm dia for fire tank complete with campanion flange as per table etc.complete in all respects as directed by Engineer-in-charge Two way inlet connection

Supply Installing , testing and commmissioning of Fire Authority approvel Electric driven fire pump suitable for automatic/ manual operation consisting of the following Horizontal high pressure single multistage centrifugal type fire pump complete with mechanical seal proper conection to suction and delivery line Squirrel cage inducation motor TEFC type suitable for 415 volt, 3 phase, 50Hz Ac supply. complete with common bace plate for mounting pump and motor fabricated of mild steel channel as per manufacturers. complete in all respects as directed by Engineer-in-charge MAIN PUMP :- 2280 LPM 70 MTR Head

Supply Installing , testing and commmissioning of Fire Authority approvel Electric driven fire pump suitable for automatic/ manual operation consisting of the following Horizontal high pressure single multistage centrifugal type fire pump complete with mechanical seal proper conection to suction and delivery line Squirrel cage inducation motor TEFC type suitable for 415 volt, 3 phase, 50Hz Ac supply. complete with common bace plate for mounting pump and motor fabricated of mild steel channel as per manufacturers. complete in all respects as directed by Engineer-in-charge JOCKEY PUMP :- 180LPM, 2900RPM 70 MTR Head HP as complete in all respects as directed by Engineer-in-charge

Supply installing, testing and commissioning of following diesel engine driven pumping sets for fire fighting purpose including, making piping and electrical connections and suitable for automatic operation. The pump set shall consist of / complete with : i) Horizontally mounted single / multistage end suction type pump of cast iron body and, ii) Water cooled diesel engine capable of developing BHP suitable for the specified duty of pump synchronous speed of RPM, iii) Common robust bed plate fabricated out of mild steel channel of appropriate size with foundation vibration damping arrangement fixed over suitably designed cement concrete foundation block, iv) Suitable coupling between pump and engine including sheet metal coupling gravel, v) Suitably designed exhaust piping system with residential type silencer to discharge engine gases to outside open air as per site conditions. Piping charges will be paid extra, vi) Welded steel constructed fuel tank conforming to relevant I.S. standard having storage capacity sufficient to allow the engine to run on full load for 6 hrs. but not less than 200 litres, vii) Automatic engine starting system including battery, boost / trickle charger including battery mounting arrangement, battery leads and other control cabling. Standby diesel engine operated Fire Pump 2280 LPM 70 MTR Head complete in all respects as directed by Engineer-in-charge

Supply Installation, Testing and Commissioning of Electric Driven Terrace Pump suitable for auto operation and consisting of following: complete in all respect as required : 450 LPM,35 Mtr HEAD complete in all respects as directed by Engineer-in-charge

Supply, fixing, testing and Commissioning of Electrical starter Control Panel for Automatic operation of above pump complete with star delta automatic switch panel. complete in all respects as directed by Engineer-in-charge

Supplying and fixing of air vessel of the following specifications:- Diameter : 450 mm, Shell Thickness: 10 mm, Dish Ends : 12 mm, Height : 2000 mm, Finishing: Two coats of red enamelpaint overprimer out side and twocoats of epoxy coatinginside. Material of construction: M.S, Test Pressure: 20 kg/sqcm., Size of Inspection flange:150 mm dia, Height of supporting legs: 300 mm complete in all respects as directed by Engineer-in-charge

Supplying and fixing of air vessel of the following specifications:- Diameter : 250 mm, Shell Thickness: 10 mm, Dish Ends : 12 mm, Height : 1500 mm, Finishing: Two coats of red enamelpaint overprimer out side and twocoats of epoxy coatinginside. Material of construction: M.S, Test Pressure: 20 kg/sqcm., Size of Inspection flange:150 mm dia, Height of supporting legs: 300 mm complete in all respects as directed by Engineer-in-charge

Providing and fixing heavy duty PVC insulated, PVC armoured aluminium conductor cables 1100V grade including necessary support clamps and connection lugs complete in all respects as directed by Engineer-in-charge Power cable 3core 10 sqmm.

Providing and fixing heavy duty PVC insulated, PVC armoured aluminium conductor cables 1100V grade including necessary support clamps and connection lugs complete in all respects as directed by Engineer-in-charge Power cable 3.5 core 36 sqmm.

Providing and fixing heavy duty PVC insulated, PVC armoured aluminium conductor cables 1100V grade including necessary support clamps and connection lugs complete in all respects as directed by Engineer-in-charge Power cable 7 core 2.5 sqmm.

Providing and fixing GI earthing wire 2 Nos. 6mm dia from motor and MCC panel to be connected in an approved manner to the general earthing system.complete in all respects as directed by Engineer-in-charge.

Fabricating and Installing following size of perforated Hot dip G.I cable tray including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with MS suspenders and including painting etc. as required.complete in all respects as directed by Engineer-in-charge 80 mm width x 50 mm depth x 1.6 mm thickness

Fabricating and Installing following size of perforated Hot dip G.I cable tray including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with MS suspenders and including painting etc. as required.complete in all respects as directed by Engineer-in-charge 150 mm width x 50 mm depth x 1.6 mm thickness

Providing and fixing M.S Heavy `C` Class Pipe including all fittings like couplings, bends, elbows, offsets, blindflanges, plugs,tees, flanges ( flanges Wall/Tank),etc.welding joints (all type )as required, supports,cutting holes and chases in brick or RCC walls/floors and making good complete as. Pipes conforming to (`C` class)complete in all respects as directed by Engineer-in-charge 25 mm dia

Providing and fixing M.S Heavy `C` Class Pipe including all fittings like couplings, bends, elbows, offsets, blindflanges, plugs,tees, flanges ( flanges Wall/Tank),etc.welding joints (all type )as required, supports,cutting holes and chases in brick or RCC walls/floors and making good complete as. Pipes conforming to (`C` class)complete in all respects as directed by Engineer-in-charge 100 mm dia

Providing and fixing M.S Heavy `C` Class Pipe including all fittings like couplings, bends, elbows, offsets, blindflanges, plugs,tees, flanges ( flanges Wall/Tank),etc.welding joints (all type )as required, supports,cutting holes and chases in brick or RCC walls/floors and making good complete as. Pipes conforming to (`C` class)complete in all respects as directed by Engineer-in-charge 150 mm dia

Providing and fixing M.S Heavy `C` Class Pipe including all fittings like couplings, bends, elbows, offsets, blindflanges, plugs,tees, flanges ( flanges Wall/Tank),etc.welding joints (all type )as required, supports,cutting holes and chases in brick or RCC walls/floors and making good complete as. Pipes conforming to (`C` class)complete in all respects as directed by Engineer-in-charge 200 mm dia

Supplying and painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved color to givean even shade including surface preparation. complete in all respects as directed by Engineer-in-charge 25 mm dia

Supplying and painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved color to givean even shade including surface preparation. complete in all respects as directed by Engineer-in-charge 100 mm dia

Supplying and painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved color to givean even shade including surface preparation. complete in all respects as directed by Engineer-in-charge 150 mm dia

Supplying and painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved color to givean even shade including surface preparation. complete in all respects as directed by Engineer-in-charge 200 mm dia

Supplying, Installation, Testing and Commissioning of CI body flanged (both ends) type `Y` strainer with (stainless steel/ brass mesh) conforming to relevant IS specifications amended upto date complete including providing and fixing nuts, bolts, washers, gaskets etc. complete as required. 200 mm dia complete in all respects as directed by Engineer-in-charge

Providing and fixing dial type pressure gauge with isolation cock and ms pipe at hydrant station.Dial diameter 100 mm celebration 0-10 kg/sq.cm. dial type pressure gauge complete in all respects as directed by Engineer-in-charge

Providing and fixing C.I. butter fly valves PN1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table E complete in all respects as directed by Engineer-in-charge 200 mm dia

Providing and fixing C.I. butter fly valves PN1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table E complete in all respects as directed by Engineer-in-charge. 150 mm dia

Providing and fixing C.I. butter fly valves PN1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table E complete in all respects as directed by Engineer-in-charge. 100 mm dia

Providing and fixing cast iron dual plate wafer type non return valves of PN.1.6 including nuts,bolts, 1.5mmthick compressed asbestos gasket including matching flanges asper table`E`complete in all respects as directed by Engineer-in-charge. 200 mm dia

Providing and fixing cast iron dual plate wafer type non return valves of PN.1.6 including nuts,bolts, 1.5mmthick compressed asbestos gasket including matching flanges asper table`E`complete in all respects as directed by Engineer-in-charge 150 mm dia

Providing and fixing cast iron dual plate wafer type non return valves of PN.1.6 including nuts,bolts, 1.5mmthick compressed asbestos gasket including matching flanges asper table`E`complete in all respects as directed by Engineer-in-charge 100 mm dia

Supply and installation of Pressure switches of suitable range for pump sets with Isolation valves.: Pressure switches complete in all respects as directed by Engineer-in-charge

Providing and fixing C.I. foot valves including nuts, bolts,1.5mm thick compressed asbestos gasket complete and companion flange as per table ` E `in all respects . 100mm dia.complete in all respects as directed by Engineer-in-charge

Providing and fixing resilient rubber lined neoprene single arch vibration eliminators with unit control suitable for fire pump upto 450 C. Temperature working pressure 20 Kg. per square centimeter. complete in all respects as directed by Engineer-in-charge 150 mm dia

Providing and fixing resilient rubber lined neoprene single arch vibration eliminators with unit control suitable for fire pump upto 450 C. Temperature working pressure 20 Kg. per square centimeter. complete in all respects as directed by Engineer-in-charge 100 mm dia.

Providing and fixing stainless steel single acting air release valve with screwed inlet 25 mm dia. air release valve complete in all respects as directed by Engineer-in-charge

Providing and fixing brass ball valve full bore type with plastic coated lever and female ends tested to 16 Kg cm2 of approved quality as specified. 25 mm dia complete in all respects as directed by Engineer-in-charge

Supply, installation, testing and commissioning of ISI marked (IS:2878) Fire Extinguisher, Carbon-di-oxide type capacity 4.5 Kg. Flat base including valve, discharge hose of not less than 10 mm dia, 1M long and complete in all respects including initial fill with CO2 gas conforming to IS:307-1966 and walll suspension braket as required as per specifications.complete in all respects as directed by Engineer-in-charge

Providing and fixing Foam type (ISImarked) fire extinguishers consisting of welded M.S.cylindrical body squeeze leverdischarge valve 30cm long high pressuredischarge hose, discharge nozzle suspension bracket ISI marked as per IS 933finished externally with red enamel paint andfixed to wall with brackets complete withinternal charger(New Is Code: 15686) complete in all respects as directed by Engineer-in-charge 9 litres capacity

Providing and fixing Foam type (ISImarked) fire extinguishers consisting of welded M.S.cylindrical body squeeze leverdischarge valve 30cm long high pressuredischarge hose, discharge nozzle suspension bracket ISI marked as per IS 933finished externally with red enamel paint andfixed to wall with brackets complete withinternal charger(New Is Code: 15686) complete in all respects as directed by Engineer-in-charge 50 litres trolley mounted

Providing and fixing ABC Type dry powder extinguisher as per new IS:15686 consisting of Welded MS Cylindrical body, with discharge valve, hanging arrangement complete.Capacity-4 Kg

Supply, installation of fire bucket with stand including sheet metal (16 gauge) shade, platform and associated 4 Nos. bucket each set.complete in all respects as directed by Engineer-in-charge

Providing and fixing M.S. Structural work fabricated from standard sections e.g. M.S. rounds, angles, channels incleding cutting to size, drilling, welding, fixing and welding to insert plates in RCC structural members as directed by Project Manger including cutting and making good the walls and floors [for pipe supports from floor. (40x40x5)complete in all respects as directed by Engineer-in-charge

Providing and fixing signages printed on acrelic PVC sheet of 1.0 mm ( plus -10%) containinglumigen II as base chemical, covered under UV stablized coating and of appropriate size (Gio-lite or eq. Make) including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects as directed by Engineer-in-charge

Providing and fixing 25 mm dia gunmetal sight glass assembly including making connection with drain line (inlet, outlet and bypass valves to be paid seperately).

Providing and fixing electric flow switch, capable of sensing a minimum flow of one sprinkler, including making electrical cable termination. 80 mm to 150 mm dia.

Providing and fixing Announcation Panel 6 Zone for operation of flow switch.

Providing and fixing 15 mm dia gunmetal quick response sprinkler head with quartz bulb and set to operate at specified temperature. Sprinkler head shall UL-FM approval. A. pendent/upright type sprinkler

Providing and fixing 25 mm dia, UL-FM approval flexible stainless steel (SS 304) pipe for making final connection of sprinkler head with sprinkler system piping network including 2 nos. 25mm diameter G.I. connector, G.I. Nipple, Reducer, elbow and threaded jointing complete as per detail. (Make HD/VIKING ) : 1000-1200 mm long.

Supply, installation, testing and commissioning of 150 mm dia Zonal Control Valve inclusive of 1 nos 100 mm dia butterfly valve, 100mm diam. non return valve, Flow Switch, water pressure gauges and 25 mm dia. Auxillary Drain valve with sight glass with necessary GI (H) piping with threaded fittings of required sizes complete.

Supply, installation, fixing, testing and commissioning of addressable analog plug in type of smoke detectors Photoelectric type with optical chamber, red led lamp for indication,complete in all respect as directed by engineer-in-charge.

Supply, installation, fixing, testing and commissioning of response indicator lamp assembly mounted on walls/partitions etc. in dust tight enclosures, complete in all respect as directed by engineer-in-charge.

Supply, installation, fixing, testing and commissioning of addressable analog Manual call point in ABS plastic body(Break glass) to initiate audio visual alarm as per specifications complete in all respect as directed by engineer-in-charge.

Supply, installation, testing and commissioning of addressable analog Fire Alarm Hooter having an audible range of 25 meters complete in all respect as directed by engineer-in-charge..

Supplying, installation, fixing, testing and commissioning of analog Addressable type 1 Loop Automatic main fire alarm control panel annunciation to indicate fire and fault,LCD display, LED lamps for visual indication, audio alarm unit, push buttons for acknowledge, test, reset complete with power supply unit for 24 Volt DC from 230 Volt AC and backed up in a suitable M.S. sheet enclosure complete with painting complete in all respect as directed by engineer-in-charge.

Supply and fixing of 11KV pilfer resistant metering cubicles consisting of 1 nos 3 Ph dry type PT confirming and3 Nos 11KV Measuring CTs of Various ration confirming with latest DHBVN Specification.

Supply and fixing of 11KV XLPE U/G Outdoor heat Shrinkable end termination kit.3c x 185 Sq.mm

Supply and fixing of heat Shrinkable for straight through joint kit for 3/c x 300sqmm11 KV cable.

Providing and fixing Lettering with Stainless Steel Grade 304 material of desired thickness including fixing accessries such as nut, bolt, fastners, bond etc. as per drawing approved by Engineer in charge. (For payment purpose only height of letter will be considered in cm)

Bidder Name

Amount

pyramid builders (GSTN-06AABFP1803F1ZT) BID ID -1120227

M/s Harpal Singh (GSTN-06ATWPS9686B1ZS) BID ID -1120960

M/s Harpal Singh

M/s Harpal Singh